Fabrication of multiscale surface-chemical gradients by means of photocatalytic lithography

We describe a new method for the fabrication of surface-chemical gradients. A film of titanium dioxide is brought into close proximity to a uniformly monolayer-covered surface and exposed to UV light to produce oxygen radicals. The use of a gradated grayscale mask between the UV source and the TiO2 allows the production of surface-chemical gradients via oxidation of the monolayer. The technique is demonstrated on gold surfaces bearing alkanethiol SAMs. Oxidation and subsequent replacement of the oxidized thiols has been used to produce surface-chemical gradients with lengths on the submillimeter to centimeter scales. The oxidation, removal, and replacement of the thiols during the process have been demonstrated by means of XPS. This oxidative process may be applied to other surface chemistries. Similarly, other shapes and slopes of gradients may be produced, depending on the photomask employed.     

Nanoemulsions prepared by a two-step low-energy process

A simple low-energy two-step dilution process has been applied in oil/surfactant/water systems with pentaoxyethylene lauryl ether (C12E5), dodecyldimethylammonium bromide, sodium bis(2-ethylhexyl)sulfosuccinate, sodium n-dodecyl sulfate-pentanol, and hexadecyltrimethylammonium bromide-pentanol. Appropriate formulations were chosen for the concentrate to be diluted with water to generate oil-in-water (O/W) emulsions or nanoemulsions. For the system of decane/C12E5/water, bluish, transparent nanoemulsions having droplet radii of the order of 15 nm were formed, only when the initial concentrate was a bicontinuous microemulsion, whereas opaque emulsions were generated if the concentrate began in an emulsion-phase region. Nanoemulsions generated in the system decane/C12E5/water have been investigated both by dynamic light scattering (DLS) and contrast-variation small-angle neutron scattering (SANS). The SANS profiles show that nanodroplets exist as spherical core-shell (decane-C12E5) particles, which suffer essentially no structural change on dilution with water, at least for volume fractions phi down to 0.060. These results suggest that the nanoemulsion droplet structure is mainly controlled by the phase behavior of the initial concentrate and is largely independent of dilution. A discrepancy between apparent nanoemulsion droplet sizes was observed by comparing DLS and SANS data, which is consistent with long-range droplet interactions occurring outside of the SANS sensitivity range. These combined phase behavior, SANS, and DLS results suggest a different reason for the stability/instability of nanoemulsions compared with earlier studies, and here it is proposed that a general mechanism for nanoemulsion formation is homogeneous nucleation of oil droplets during the emulsification.     

Order and composition of methyl-carboxyl and methyl-hydroxyl surface-chemical gradients

A detailed infrared and XPS characterization of surface-chemical gradients of dodecanethiol with 11-mercaptoundecanol or 11-mercaptoundecanoic acid self-assembled on gold, is reported. Gradients were prepared using a simple, two-step process previously reported from our laboratory, which involves a controlled immersion of a polycrystalline gold substrate in a dilute (5 microM) solution of one component and a subsequent back-filling with the other. FTIR measurements show that a single-component gradient of dodecanethiol is composed of disordered, liquidlike alkyl chain conformations. Such a gradient, when back-filled with a complementary thiol, having either a hydroxyl or carboxyl end-group, yields two-component gradients that show similar changes in wettability along their lengths. However, while gradients composed of methyl and hydroxyl end-groups show a well-ordered alkyl chain structure over their entire length, methyl-carboxyl gradients exhibit a greater conformational disordering toward the carboxyl-rich end.     

受控水解法制备纳米TiO2光催化剂及其结构性能

由于纳米TiO2比表面积大,表面活性高,无毒,具有较高的化学稳定性和优良的光催化性能,在作为光催化材料去除空气及水中的有机污染和抗菌、自洁方面具备广阔的前景。     

Synthesis of hydroxylated oligoarene-type phosphines by a repetitive two-step method

Hydroxylated oligoarene-type phosphines with various substitution patterns were synthesized. Such phosphines have potential as ligands for transition metal-catalyzed reactions. A successful route, which includes a repetitive Suzuki-Miyaura coupling-triflation sequence, reduction, and salt formation, was established starting from 2-bromophenyldicyclohexylphosphine oxide. Other key aspects of the method are the use of suitable triflation reagents and the formation of phosphines as HBF₄ salts. Interesting information was obtained from careful analysis of the byproducts in the triflation and reduction steps, and the mechanisms for their formation were proposed.     

Profile control in surface amine gradients prepared by controlled-rate infusion

Surface amine gradients that exhibit a wide variety of profiles, including those that incorporate spatially distinct regions having steep and gradual variations in chemical functionality, have been prepared by the sol-gel process using a controlled-rate infusion method. In this work, a substrate that incorporates dimethyl and Si-OH groups is temporally modified with an aminoalkoxysilane (NH(2)(CH(2))(3)Si(OC(2)H(5))(3)) to build a gradient film for which the amine content changes over a 10-20 mm distance. Both X-ray photoelectron spectroscopy (XPS) and contact angle measurements confirm the presence of a chemical gradient across the surface of the film. As expected, a greater density of amine functionalities and lower contact angle were found at the bottom of the gradient relative to the top. The local steepness of the gradient was systematically controlled by changing the rate of infusion. Fast rates of infusion created gradient surfaces where the amine content changed slowly along the surface and never reached saturation, whereas slow rates of infusion formed a surface exhibiting a steep rise in amine content followed by saturation. The steepness of the gradient was also changed at predefined positions along its length by programming the rate of infusion. Gradients prepared using six-step, three-step, and two-step programmed infusion rates are shown. The data fit nicely to a kinetic model that assumes first-order kinetics. The ability to manipulate the gradient profile is particularly vital for applications that rely on mass transport and/or those that require spatial control of gradient properties.     

添加表面活性剂两步沉淀法制备甲醇催化剂

采用添加表面活性剂两步沉淀法制备了具有高表面铜相对浓度的超细甲醇合成催化剂。以组成为H2/CO/CO2/N2=66/27/3/4(体积比）的原料气对催化剂进行了活性评价。结果表明,该催化剂比传统并流沉淀法制备的铜基催化剂活性提高47.9%,比两步沉淀法和添加表面活性剂并流沉淀法制备的铜基催化剂活性分别提高9.3%和16.8%。利用SEM、XRD及XPS方法对催化剂的结构、形貌和表面金属组成进行了表征。     

Preparation and structure of highly confined intercalated polystyrene/montmorillonite nanocomposite via a two-step method

A two-step approach with a combination of emulsion polymerization and melt intercalation with higher clay loading of 33 wt.% is disclosed to highly confine the polystyrene (PS) chains by montmorillonite. The product of the emulsion polymerization is an easily crushable fine powder. And the powder is readily processible by open mill to form a transparent sheet. In the melt intercalation process, further intercalation of polystyrene narrows the space among the tactoids and results a highly confined intercalated nanocomposite. The results of dynamic mechanical thermal analysis (DMTA) and differential scanning calorimetry (DSC) showed that the cooperative motions of PS segments were substantially depressed, indicative of the highly intercalated structure formed in the nanocomposites. A structural model is proposed to explain the highly confined mesostruture of the PS/MMT nanocomposite.     

Effects of preparation conditions of Au/FeOx/Al203 catalysts prepared by a modified two-step method on the stability for CO oxidation

Composite oxide FeO x /Al 2 O 3 -supported gold catalysts were prepared by a modified two-step method. The effects of preparation conditions on the initial catalytic activity and long-time stability were studied for CO oxidation. XRD, XPS and in situ FTIR were employed to investigate the state of FeO x and the species on the catalyst surface. The results showed that Au/FeO x /Al 2 O 3 catalysts prepared by this method exhibited high activity and high stability in a wide pH value range. Calcination pretreatment was proved to be beneficial to improving the activity and stability. The beneficial effects of FeO x acting as a structural promoter could be ascribed to the ability to supply active oxygen species. As the precursor of FeO x , Fe(NO 3 ) 3 is superior to FeCl 3 for obtaining higher stability.     

High compact melamine-formaldehyde microPCMs containing n-octadecane fabricated by a two-step coacervation method

Microcapsules containing n-octadecane were successfully fabricated by an in-situ polymerization process with melamine-formaldehyde (MF) prepolymer and a hydrolyzed copolymer of styrene and maleic anhydride (SMA) as shell materials. To achieve a long service time of microcapsules containing phase change materials (microPCMs), the compactness of shells was improved by adding the MF prepolymer twice. The mechanism of this method was a two-step coacervation (TSC) under the help of hydrolyzed SMA compared to a one-step coacervation (OSC). To understand the influence of both coacervations, properties of shells were investigated in terms of morphologies, density, thickness, and stability by means of scanning electron microscopy (SEM), transmission electron microscopy, and thermal gravimetric analysis (TGA). The data of shells thickness were achieved from the cross-section SEM images. It shows that the average thickness of shells from two kinds of process are 0.1 μm. The density and stability in water of shells fabricated by TSC are both higher than that of shells by OSC. TGA curves show the expected microPCMs of TSC losing weight from 200 to 400 °C. The release curves, relationship between time and logarithmic residual weight of core, show there are two decrease-linear steps after curve regression. It can be concluded from all these results that the TSC method may be a promising method leading to a compact shell structure for various application.     

Defects in ZnO nanorods prepared by a hydrothermal method

ZnO nanorod arrays were fabricated using a hydrothermal method. The nanorods were studied by scanning electron microscopy, photoluminescence (PL), time-resolved PL, X-ray photoelectron spectroscopy, and positron annihilation spectroscopy before and after annealing in different environments and at different temperatures. Annealing atmosphere and temperature had significant effects on the PL spectrum, while in all cases the positron diffusion length and PL decay times were increased. We found that, while the defect emission can be significantly reduced by annealing at 200 degrees C, the rods still have large defect concentrations as confirmed by their low positron diffusion length and short PL decay time constants.     

Morphology and structure of micro- and nanosize polytetrafluoroethylene powders prepared by the gas-phase method

Formation of fluoropolymer nanoaerosols and micropowders in the gas products of polytetrafluoroethylene pyrolysis and the hierarchical self-organization of ultradispersed powders were revealed. The features of the molecular and supramolecular structures of powders were analyzed. Low- and high-molecular-weight fractions of the fluoropolymers, constituting the powder particles were identified, and a method for their partitioning was proposed.     

Thermoplastic and thermosetting properties of polyphenylsilsesquioxane particles prepared by two-step acid-base catalyzed sol-gel process

Polyphenylsilsesquioxane (PhSiO_3/2) particles were synthesized by a two-step acid-base catalyzed sol-gel process, in which phenyltriethoxysilane used as a starting alkoxide was hydrolyzed and condensed in the first step under two different acid-catalyzed conditions. The PhSiO_3/2 particles prepared under an acid-catalyzed process without using a solvent were thermally hardened after the first heating up to 200°C. In contrast, the PhSiO_3/2 particles prepared under an acid-catalyzed process with ethanol as a solvent were thermally softened with the repeated heating processes up to 200°C. From the gel permeation chromatography measurements, it was found that the average molecular weight of the particles prepared with the use of ethanol was decreased in comparison with that of the particles prepared without using ethanol. The addition of ethanol in the sols during hydrolysis and condensation reaction under the acid-catalyzed process caused the decrease in the average molecular weight, which should result in the changes of thermal property of PhSiO_3/2 particles from thermosetting to thermoplastic.     

Versatile wettability gradients prepared by chemical modification of polymer brushes on polymer foils

A method to create a wettability gradient by variation of the chemical functionality in a polymer brush is presented. A poly(N-methyl-vinylpyridinium) (QP4VP) brush was created on a poly(ethylene-alt-tetrafluoroethylene) (ETFE) foil by the grafting of 4-vinylpyridine and subsequent quaternization. The instability of QP4VP, a strong polyelectrolyte, in alkaline media was exploited to transform it to the neutral poly(vinyl(N-methyl-2-pyridone)) (PVMP), as confirmed with ATR-IR spectroscopy. The slow transformation resulted in a substantial, time-dependent decrease in wettability. A nearly linear gradient in water contact angle (CA) was created by immersion of a QP4VP brush modified sample into a sodium hydroxide solution, resulting in CAs ranging from 10° to 60°. The concurrent decrease in the number of charged functional groups along the gradient was characterized by loading an anionic dye into the polymer brush and measuring the UV transmittance of the sample. The versatility of the wettability gradient was demonstrated by exchanging the counterions of the N-methyl-vinylpyridinium groups, whereby a reversal of gradient direction was reproducibly achieved.     

Effects of preparation conditions of Au/FeO_x /Al_2O_3 catalysts prepared by a modified two-step method on the stability for CO oxidation

Composite oxide FeO x /Al 2 O 3 -supported gold catalysts were prepared by a modified two-step method. The effects of preparation conditions on the initial catalytic activity and long-time stability were studied for CO oxidation. XRD, XPS and in situ FTIR were employed to investigate the state of FeO x and the species on the catalyst surface. The results showed that Au/FeO x /Al 2 O 3 catalysts prepared by this method exhibited high activity and high stability in a wide pH value range. Calcination pretreatm...     

Microcellular structure of a thin polycarbonate sheet prepared by compression molding

Microcellular thin polycarbonate sheets have been prepared by compression molding with the cell size in the range of 2∼20 microns, and cell density larger than 10⁸ cells/cm³. The effect of processing parameters on the microcellular polycarbonate structure has been investigated. The cell size decreases with increasing foaming time till 8 minute and then increases. Besides this parameter slightly decreases with increasing foaming pressure, but increases with increasing temperature. The variation of cell density is contrary to that of cell size, and the foam density decreases with increasing foaming pressure and foaming temperature and displays a variable trend with increasing foaming time under different foaming pressures.     

Preparations and properties of uniform size macroporous polymer beads prepared by two-step swelling and polymerization method utilizing divinyl succinate or divinyl adipate as a crosslinking agent

Uniform size macroporous polymer beads were prepared through a typical two-step swelling and polymerization method utilizing divinyl succinate or divinyl adipate as well as ethylene dimethacrylate as crosslinking agents. Stable macroporous polymer beads with good size monodispersity and a slightly nonspherical shape were obtained by homopolymerization of divinyl succinate in cyclohexanol as porogen. BET measurements indicated that the beads prepared by homopolymerization of divinyl succinate and copolymerization of divinyl succinate with vinyl p-tert-butylbenzoate, as well as homopolymerization of ethylene dimethacrylate had relatively large specific surface area. In contrast, copolymerization of divinyl succinate with methyl methacrylate afforded beads having a very small specific surface area. Similarly, all the beads prepared using divinyl adipate had very small specific surface area, while size exclusion chromatography in tetrahydrofuran suggested that these beads acquired a porous structure as a result of swelling. When used as packing materials for high-performance liquid chromatography, the beads prepared with divinyl adipate showed unexpected molecular recognition toward flat solutes in reversed phase liquid chromatography in contrast to those prepared with ethylene dimethacrylate. Copolymerizations with methyl methacrylate led to a decrease in molecular recognition, while those with vinyl p-tert-butylbenzoate enhanced the selectivity. © 1996 John Wiley & Sons, Inc.     

Molecular weight distribution in polyacrylamide prepared by a photochemical method

The molecular weight distribution of polyacrylamide, prepared by uranyl ion-photosensitized polymerization of acrylamide in visible light of wavelength 436 mμ, was studied in detail. The polymer was fractionated and the experimental integral and differential distribution curves were drawn. The theoretical distribution function was derived from the kinetics of photopolymerization, assuming the rate constants calculated from previous studies. The theoretical and experimental molecular weight distributions were compared. The results support the mechanism proposed for the photopolymerization reaction.     

Gelation behavior and phase separation of macroporous methylsilsesquioxane monoliths prepared by in situ two-step processing

An in situ two-step processing using an initial acid catalysis step accompanied by an epoxide-mediated condensation step in the presence of ammonium chloride (NH₄Cl) is reported, and macroporous cocontinuous methylsilsesquioxane (MSQ) monoliths have been successfully prepared by this processing. We explain the hydrolysis, gelation behavior and phase separation of MTMS(methyltrimethoxysilane)-MeOH(methanol)-HCl-PO(propylene oxide) system and the in situ effect of NH₄Cl, and examine the macroporous morphology and pore structures of MSQ monoliths obtained under different conditions. Macroporous MSQ monolith under optimized conditions possesses a narrow macropore size distribution between 3 to 10 μm, surface area as high as 366 m²·g^?1 and minimal shrinkage of only 1 %.     

Direct structure determination of a multicomponent molecular crystal prepared by a solid-state grinding procedure

A three-component molecular cocrystal material has been prepared by a solvent-free route involving mechanical grinding of the pure phases of the individual components. This material is not accessible from conventional solution-state crystallization procedures. Due to the fact that the grinding procedure intrinsically leads to a microcrystalline powder sample, the use of powder X-ray diffraction data is essential for structure determination. This work emphasizes the scope and utility of ab initio structure solution directly from powder X-ray diffraction data for carrying out structural characterization of new materials prepared via the solid-state grinding route, leading to the opportunity to establish structure-property relationships for such materials.