Poly(dopamine) assisted epoxy functionalization of hexagonal boron nitride for enhancement of epoxy resin anticorrosion performance

Hexagonal boron nitride (h‐BN) is modified by a simple and green method based on self‐oxidation of dopamine and epoxy groups functionalized silane (KH560) grafting. The surface modification and microstructure of h‐BN are characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy, scanning electron microscopy and transmission electron microscopy. The poly(dopamine) and epoxy groups not only increase the compatibility of the h‐BN and enhance its interaction with epoxy matrix but also exhibit a remarkable superiority in enhancing the anticorrosion performance of epoxy coatings. In addition, the anticorrosion mechanisms of h‐BN@PDA‐KH560 are tentatively discussed. Copyright © 2016 John Wiley & Sons, Ltd.     

Raman spectroscopy of C-, BN-, SiC-layers deposited on multifilament substrates

The analytic characterisation of various layers and layer systems on fibrous materials are presented. The layers, deposited by an isothermal CVD process, consisting mainly of pyrolytic carbon, hexagonal boron nitride and silicon carbide were characterised by different analytical methods, especially by Raman spectroscopy [1]. The surface enhanced Raman spectroscopy (SERS) was used first time for the investigation of boron nitride (BN) coatings on fibres.     

Fabrication of Hexagonal Boron Nitride Nanosheets by Using a Simple Thermal Exfoliation Process

A simple and inexpensive method to exfoliate boron nitride powder to form boron nitride nanosheets (BNNSs) with few layers was achieved by using a physically thermal process. The obtained BNNSs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), atomic force microscopy (AFM), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), IR spectroscopy, and Raman spectroscopy. The size distribution of the sheets and average sheet size is in the range of 80–380 nm and 200±62 nm, respectively, and the pure phase h‐BN products were confirmed. XPS result showed the B/N atomic ratio to be 0.99. In addition, the BNNSs can well disperse in aqueous solution to form a cloudy suspension and importantly, can remain suspended for 1 month without precipitate, which would have good potential in a wide range of applications.     

Chitosan‐Templated Synthesis of Few‐Layers Boron Nitride and its Unforeseen Activity as a Fenton Catalyst

A novel procedure for the preparation of few‐layers boron nitride (BN), either as films or as suspended BN platelets, is presented, based on the pyrolysis of chitosan, which serves both as a matrix to embed ammonium borate and as a template for BN synthesis. The resulting BN samples are characterized by XRD, Raman and X‐ray photoelectron spectroscopy, and by TEM and AFM imaging. The samples exhibit deep UV emission, which is characteristic of high quality BN. This template synthesis and the easy exfoliation of BN platelets facilitate the use of BN as an extremely high‐efficiency Fenton catalyst for the generation of highly aggressive hydroxyl radicals in water.     

Functionalization and Dispersion of Hexagonal Boron Nitride (h‐BN) Nanosheets Treated with Inorganic Reagents

A mixture of bulk hexagonal boron nitride (h‐BN) with hydrazine, 30 % H₂O₂, HNO₃/H₂SO₄, or oleum was heated in an autoclave at 100 °C to produce functionalized h‐BN. The product formed stable colloid solutions in water (0.26–0.32 g L ^?1) and N,N‐dimethylformamide (0.34–0.52 g L ^?1) upon mild ultrasonication. The yield of “soluble” h‐BN reached about 70 wt %. The dispersions contained few‐layered h‐BN nanosheets with lateral dimensions in the order of several hundred nanometers. The functionalized dispersible h‐BN was characterized by IR spectroscopy, X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, UV/Vis spectroscopy, X‐ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM). It is shown that h‐BN preserves its hexagonal structure throughout the functionalization procedure. Its exfoliation into thin platelets upon contact with solvents is probably owing to the attachment of hydrophilic functionalities.     

Seamless Rim‐Functionalization of h‐BN with Silica—Experiment and Theoretical Modeling

Boron nitride contains six‐ring layers, which are isostructural to graphene, and it exhibits similar extraordinary mechanical strength. Unlike graphene, hexagonal boron nitride (h‐BN) is an insulator and has some polar features that make it a perfect material for those applications graphene is not suitable for, for example, purely ionic conductors, insulating membranes, transparent coatings, composite ceramics, high oxidation resistance materials. We report here a selective rim‐functionalization of h‐BN with SiO₂ by using the Stöber process. A closed, protruding ring of SiO₂ is formed covering all edges perpendicular to the [001] zones of the h‐BN stacks and thus shield the most reactive centers of BN layers. SEM and HAADF‐STEM images, X‐ray spectroscopy, and atomic force microscopy confirm the rim‐functionalization by SiO₂. XRD demonstrates the absence of any intercalation phenomenon of BN and reveals the glassy nature of the SiO₂ rims. Selected variations of synthesis and theoretical modeling both confirm that rim activation by water prior to the Stöber condensation is crucial. First‐principles calculations also confirm that dangling bonds of clean BN edges merge to give interlayer bonds that make further functionalization much more difficult. The reported reaction pathway should allow for other new functionalizations of pure BN and of the rimmed SiO₂/h‐BN composites.     

Deposition and characterization of TiAlSiN coatings prepared by hybrid PVD coating system

TiAlSiN coatings with different Si contents were deposited on silicon and high‐temperature alloy by using a hybrid physical vapor deposition coating system, where the cathodic arc ion plating was combined with a twin target mid‐frequency magnetron sputtering. The chemical composition, microstructure, cross‐sectional structure and morphology were carried out by X‐ray photoelectron spectroscope (XPS), X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscope (TEM), respectively. NanoTest 600 nanomechanical system and ball‐on‐disc friction tester were used to investigate the mechanical and friction properties of TiAlSiN coatings. The worn surface of the TiAlSiN coatings and counterballs were investigated by means of surface profilometer and optical microscope. The wear rates were also measured by surface profilometer. The results showed that the Si addition did not change the coatings growth orientation, and the coating transfered into amorphous phase when the Si content reached about 13.9 at.%. The tribological properties and the hardness were improved by solid solution of Si atoms and grain boundary strengthening of SiN_x amorphous phase with moderate Si content addition. In addition, the SiNx amorphous phase improved oxidation resistance of TiAlN coating, but with a high Si content (more than 8.3 at.% in this work) the agglomeration of SiN_x amorphous phase would reduce the mechanical properties and oxidation resistance of the coating. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of AA2024‐T3 surface pretreatment on the physicochemical properties and the anticorrosion performance of poly(γ‐glycidoxypropyltrimethoxysilane) sol‐gel coating

This study investigated the dependence of the anticorrosion performance of a poly(γ‐glycidoxypropyltrimethoxysilane) (poly(γ‐GPTMS)) sol‐gel coating on AA2024‐T3 aluminum alloy surface state. Two different AA2024‐T3 surface pretreatment procedures were tested: a degreasing with acetone and a chemical multistep etching process (industrial chemical etching pretreatment). Poly(γ‐GPTMS) coatings were deposited onto both pretreated surfaces using the dip‐coating technique. Surfaces were characterized principally by scanning electron microscopy, X‐ray photoelectron spectroscopy, Fourier transform infrared attenuated total reflectance, contact angles, and roughness measurements. Moreover, for the coated AA2024‐T3 surfaces, a pull‐off test was used to evaluate the poly(γ‐GPTMS) adhesion to the pretreated surface. Bare surface properties depended on the applied pretreatment. The chemically etched surface was the roughest and the most concentrated in hydroxyl groups. In addition, comparatively to the degreased surface, it has a more hydrophobic character. Poly(γ‐GPTMS) coating revealed an uneven nature and a poor adhesion once it was deposited onto the degreased surface. Coatings anticorrosion performances were evaluated using electrochemical impedance spectroscopy measurements (EIS). Electrochemical impedance spectroscopy data proved that the sol‐gel coating applied onto the chemically etched surface had better anticorrosion performance.     

Preparation and characterization of copper/silver bimetallic nanowires with core‐shell structure

Core‐shell copper/silver bimetallic nanowires were prepared by replacement reaction with citric acid and polyvinylpyrollidone at room temperature. A uniform silver coating was obtained by strictly controlling the molar ratio of Ag/Cu. The copper/silver composite was characterized by X‐ray diffraction, scanning electron microscopy, electron probe microanalysis and X‐ray photoelectron spectroscopy. Microscopic analysis shows that a well‐copper/silver core‐shell structure was formed. Thermo‐gravimetry and differential thermal analysis to the composite nanowires show that the silver coatings efficiently inhibit the oxidation of Cu. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of intermediate Ar plasma treatments on CrN coating microstructures and property evolutions

Chromium nitride (CrN) coatings with different steps of intermediate argon plasma treatments were deposited with primary (200) orientation by multi‐arc ion plating technique. By virtue of scanning electron microscopy, X‐ray diffraction and high‐resolution transmission electron microscopy, the influence of intermediate argon plasma treatments on the coating microstructures, mechanical properties and corrosion properties as well as tribological behaviors in artificial seawater solutions were systematically investigated. It was assumed that the mechanical properties, adhesion strength, corrosion and tribological performances of coatings depended on argon plasma treatment steps. High‐performance coatings could be obtained by proper plasma treatment steps. The superior anti‐corrosion ability of coating with appropriate treatment steps may be ascribed to the increased charge transfer resistance due to alternative interface and CrN layer and the compact microstructure. On the other hand, the excellent tribological performances in seawater conditions may be attributed to the enhanced mechanical properties. Otherwise, further increase in treatment steps was assumed to distinctly increase defects and deteriorate the coating integrity thus weakening coating properties and behaviors. Copyright © 2016 John Wiley & Sons, Ltd.     

Nitridation of V5Al8 films with NH3 by Rapid Thermal Processing (RTP)

V₅Al₈ films (thickness about 100 nm) were deposited on sapphire substrates by RF‐sputtering and nitridated with NH₃ at 600‐1250 °C (1 min) in a RTP system. The as deposited and nitridated films were investigated by ESCA (electron spectroscopy for chemical analysis), XRD (X‐ray diffraction), XRR (X‐ray reflectometry), AFM (atomic force microscopy) and SEM (scanning electron microscopy). Formation of an aluminum nitride layer at the surface and precipitation of V(Al) in the bulk was found. In the temperature regime from 600 °C to 900 °C a considerable amount of oxygen is incorporated in the aluminum nitride layer. The roughness of the surface increased with increasing temperature and at 1250 °C a partially detaching of the AlN layer could be observed.     

Thickness determination of TiN and TiAl coatings on steel substrates using X‐ray diffraction method and their composition measurements by GD‐OES

This paper presents a nondestructive X‐ray diffraction method for the accurate determination of thicknesses of polycrystalline TiN and amorphous‐like TiAl coatings deposited by DC magnetron sputtering onto thick polycrystalline stainless steel and carbon steel substrates. This method relies on the measurement of intensity loss of a substrate reflection caused by the deposition of the coating. The uncertainty of the thickness measurements by the X‐ray diffraction depends on the mass absorption coefficient of the coating material and the quality of the collected diffraction patterns. For the coatings considered, thicknesses determined by the X‐ray diffraction method show very good agreement with the thickness values measured by scanning electron microscopy and ball crater techniques.     

Rivalry under Pressure: The Coexistence of Ambient‐Pressure Motifs and Close‐Packing in Silicon Phosphorus Nitride Imide SiP2N4NH

Non‐metal nitrides such as BN, Si₃N₄, and P₃N₅ meet numerous demands on high‐performance materials, and their high‐pressure polymorphs exhibit outstanding mechanical properties. Herein, we present the silicon phosphorus nitride imide SiP₂N₄NH featuring sixfold coordinated Si. Using the multi‐anvil technique, SiP₂N₄NH was obtained by high‐pressure high‐temperature synthesis at 8 GPa and 1100 °C with in situ formed HCl acting as a mineralizer. Its structure was elucidated by a combination of single‐crystal X‐ray diffraction and solid‐state NMR measurements. Moreover, SiP₂N₄NH was characterized by energy‐dispersive X‐ray spectroscopy and (temperature‐dependent) powder X‐ray diffraction. The highly condensed Si/P/N framework features PN₄ tetrahedra as well as the rare motif of SiN₆ octahedra, and is discussed in the context of ambient‐pressure motifs competing with close‐packing of nitride anions, representing a missing link in the high‐pressure chemistry of non‐metal nitrides.     

Surface‐interface microstructures and binding strength of cathodic arc ion plated TiCN coatings on YT14 cutting tools

A titanium carbonitride (TiCN) coating was deposited on YT14 cutting tool by using a CAIP (cathodic arc ion plating). The surface‐interface morphologies, chemical compositions, and phases of TiCN coatings were observed by using a FESEM (field emission scanning electron microscopy), EDS (energy dispersive spectroscopy), XRD (X‐ray diffraction), respectively, and the bonding energy, surface roughness, and bonding strength were characterized with an XPS (X‐ray photoelectron spectroscopy), AFM (atomic force microscope), and scratch test, respectively. The results show that the phases of the TiCN coating are primarily composed of TiN, TiC, and amorphous C, of which the TiC and TiN increases the coating hardness, and the amorphous C atom improves friction and lubrication properties of the coating. The effect of CAIP on the topography of the TiCN coating is at nano‐scale, the Ti and N atoms are enriched in the coating at the bonding interface, and the part of chemical elements are diffused in the gradual transformation layer. The bonding form of the TiCN coating interface is primarily composed of mechanical combination, accompanying with slight metallurgical combination, and the bonding strength is characterized with 60.85 N by scratch test. Copyright © 2016 John Wiley & Sons, Ltd.     

Modified boron nitride as an efficient synergist to flame retardant natural rubber: preparation and properties

A new flame retardant system with organic modified boron nitride (m‐BN) and intumescent flame retardant (IFR) was used in this paper, and the synergistic flame retardancy of m‐BN and IFR on natural rubber (NR) was studied. NR/IFR/m‐BN composites were characterized by X‐ray photoelectron spectroscopy(XPS), Fourier transform infrared spectrometry (FTIR), thermogravimetric analysis, UL‐94, limiting oxygen index (LOI), tensile testing, cone calorimeter testing, and thermal conductivity testing. When 4 wt% m‐BN was added, the flame retardancy and mechanical properties of the composites were improved. The LOI value of NR/IFR/4 phr m‐BN reached 26.8%, and suppressed fire spread in a UL‐94 test. Compared with pure NR, the peak heat release rate (pHRR) was reduced by 52.2%, the total heat release (THR) was reduced by 27.6%, and CO yields were reduced by 51.4%. As a key aspect of fire safety, the ignition time is effectively delayed to 23 seconds due to the increased thermal conductivity of NR/IFR/m‐BN. Since the synergistic effect of m‐BN effectively improves the flame retardancy of NR, it provides a feasible method for improving the fire safety of polymers.     

Characterization of Ce‐rich coating on carbon surface by immersing in an aqueous solution containing Ce ions

Surface modification of carbon fibers with Ce‐rich coating was investigated by scanning electron microscopy (SEM), and it is shown that a Ce‐rich coating can protect carbon fibers. After the carbon surface was scratched crosswise, self‐healing behavior of carbon surface with chemical immersion treatment from Ce salt solution was investigated at various immersion times. The Ce‐rich compounds deposited easily on the scratch sites, filling it with Ce‐rich compounds. Such self‐healing behavior enables the carbon surface to protect itself. X‐ray photoelectron spectroscopy (XPS) results indicate that Ce⁴⁺ was the dominant oxidation state for the Ce‐rich coating on the carbon surface. Copyright © 2009 John Wiley & Sons, Ltd.     

Cleaning of pyrolytic hexagonal boron nitride surfaces

Hexagonal boron nitride (h‐BN) has recently garnered significant interest as a substrate and dielectric for two‐dimensional materials and devices based on graphene or transition metal dichalcogenides such as molybdenum disulfide (MoS₂). As substrate surface impurities and defects can negatively impact the structure and properties of two‐dimensional materials, h‐BN surface preparation and cleaning are a critical consideration. In this regard, we have utilized X‐ray photoelectron spectroscopy to investigate the influence of several ex situ wet chemical and in situ thermal desorption cleaning procedures on pyrolytic h‐BN surfaces. Of the various wet chemistries investigated, a 10 : 1 buffered HF solution was found to produce surfaces with the lowest amount of oxygen and carbon contamination. Ultraviolet/ozone oxidation was found to be the most effective ex situ treatment for reducing carbon contamination. Annealing at 1050 °C in vacuum or 10^?5 Torr NH₃ was found to further reduce oxygen and carbon contamination to the XPS detection limits. Copyright © 2015 John Wiley & Sons, Ltd.     

Micropore formation mechanism in iridium coating after high‐temperature treatment

Noble metal iridium is of great interest for high‐temperature applications and extreme environments. A high (110)‐oriented iridium coating was prepared by a double glow plasma process on the surface of niobium substrate. The morphology and composition of the coating were determined by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and X‐ray photoelectron spectroscopy, respectively. The phase of the coating was identified by X‐ray diffraction analysis. The misorientation angle distributions of grains on the surface and cross section of the coating were characterized by electron backscatter diffraction system. The uniform and pure iridium coating consisted of the submicrometer‐sized columnar grains with high‐angle boundary. The mean misorientation angles on the surface and cross section of the coating were 38.6° and 45.6°, respectively. After high‐temperature treatment, the coating was composed of equiaxed grains with distinct grain boundaries. Micropores appeared on the fracture surface of the coating. The micropore formation mechanism in Ir coating after high‐temperature treatment was investigated. Copyright © 2016 John Wiley & Sons, Ltd.     

A simple method to synthesize polyhedral hexagonal boron nitride nanofibers

Hexagonal boron nitride (h-BN) fibers with polyhedral morphology were synthesized with a simple-operational, large-scale and low-cost method. The sample obtained was studied by X-ray photoelectron spectrometer (XPS), electron energy lose spectroscopy (EELS), X-ray powder diffraction (XRD), Fourier transformation infrared spectroscopy (FT-IR), etc., which matched with h-BN. Environment scanning electron microscopy (ESEM) and transmission electron microscope (TEM) indicated that the BN fibers possess polyhedral morphology. The diameter of the BN fibers is mainly in the range of 100–500 nm.     

等离子化学气相沉积硅-硼-氮复合薄膜的组成和结构

利用X射线衍射（XRD）和X光电子能谱（XPS）等技术对射频－直流－等离子化学气相沉积（RF－DC－PVCD）在钢基本上Si-B-N复合薄膜的组成和结构进行分析和研究；结果表明，通过给试样基体加一适当的直流负偏压，得到含有显著六方氮化硼（h-BN)，立方氮化硼（c-BN)结晶相的Si-B-N薄膜。