Towards the Fabrication of the Top‐Contact Electrode in Molecular Junctions by Photoreduction of a Metal Precursor

Langmuir films of 4‐{[4‐({4‐[(trimethylsilyl)ethynyl]phenyl}ethynyl)phenyl]ethynyl} benzenaminium chloride ([ 1 H ]Cl) undergo anion metathesis when assembled on an aqueous auric acid (HAuCl₄) subphase. Subsequent transfer to solid supports gives well‐formed Langmuir–Blodgett (LB) monolayers of [ 1 H ]AuCl₄ in which the trimethylsilyl group serves as the surface contacting group. Photoreduction of the aurate on these monolayers leads to the formation of metallic gold nanoislands, which were distributed over the surface of the film. Electrical properties of these nascent devices were determined by recording current–voltage (I–V) curves with conductive atomic force microscopy (c‐AFM) using the PeakForce tunneling AFM (PF‐TUNA) mode. This gives consistent sigmoidal I–V curves that are indicative of well‐behaved junctions free of metallic filaments and short circuits. The photoreduction of a metal precursor incorporated onto monomolecular films is therefore proposed as an effective method for the fabrication of molecular junctions.     

Effects of Fullerenes on Phospholipid Membranes: A Langmuir Monolayer Study

We investigate two‐component Langmuir monolayers of dipalmitoylphosphatidylcholine (DPPC)/C₆₀ by recording surface pressure/area (π/A) and surface potential/area (ΔV/A) isotherms and by direct Brewster angle microscopy (BAM) imaging. Atomic force microscopy (AFM) is employed to study morphologies of the mixed monolayers transferred to a solid substrate by the Langmuir–Blodgett technique. C₆₀ is shown to have little influence on isotherms of the DPPC/C₆₀ monolayers even at a molar fraction as high as X_C60=0.3. The elastic modulus ( ) versus π curves of the DPPC/C₆₀ monolayers almost overlay each other, as well as that of pure DPPC, that is, the elasticities of pure DPPC monolayers and DPPC/C₆₀ monolayers are remarkably similar. AFM studies reveal that fullerene flocs form at low surface pressures (π≤15 mN m^?1), are gradually disaggregated and dispersed in the DPPC monolayer with increasing surface pressure up to 35 mN m^?1, and are then progressively squeezed out to form protruded islands as the surface pressure increases up to 65 mN m^?1. Our work provides experimental support to the computational result that C₆₀ can dissolve in lipid bilayers without significantly compromising their mechanical properties, a finding which has important implications for the toxicity and development of drug vehicles from fullerene materials.     

Unusual Nortriterpenoid Saponins from Stauntonia chinensis

Four new saponins, yemuosides YM₁₇–YM₂₀ ( 1 – 4 , resp.), were isolated from the rattan of Stauntonia chinensis DC. (Lardizabalaceae) along with a known saponin, nipponoside D ( 5 ). Their structures were elucidated by spectroscopic analysis and chemical evidence as 20,30‐dihydroxy‐29‐noroleanolic acid 28‐O‐α‐L ‐rhamnopyranosyl‐(1→4)‐β‐D ‐glucopyranosyl‐(1→6)‐β‐D ‐glucopyranosyl ester ( 1 ), 20,29‐dihydroxy‐30‐noroleanolic acid 28‐O‐α‐L ‐rhamnopyranosyl‐(1→4)‐β‐D ‐glucopyranosyl‐(1→6)‐β‐D ‐glucopyranosyl ester ( 2 ), 29‐hydroxy‐30‐norolean‐20(21)‐enolic acid 28‐O‐α‐L ‐rhamnopyranosyl‐(1→4)‐β‐D ‐glucopyranosyl‐(1→6)‐β‐D ‐glucopyranosyl ester ( 3 ), 29‐hydroxyoleanolic acid 28‐O‐α‐L ‐rhamnopyranosyl‐(1→4)‐β‐D ‐glucopyranosyl‐(1→6)‐β‐D ‐glucopyranosyl ester ( 4 ), and 23,29‐dihydroxyoleanolic acid 28‐O‐α‐L ‐rhamnopyranosyl‐(1→4)‐β‐D ‐glucopyranosyl‐(1→6)‐β‐D ‐glucopyranosyl ester ( 5 ). Yemuoside YM₁₇–YM₁₉ ( 1 – 3 , resp.) contain novel unusual nortriterpene aglycones.     

Phenylpropanoid Esters of Rhamnose from Buddleja asiatica

Four new phenylpropanoid esters of rhamnose, asiatisides A–D, along with the known compounds, buergeriside C₁ ( 5 ), p‐methoxycinnamic acid, ferulic acid, and O‐methylferulic acid were obtained from the aerial parts of Buddleja asiatica Lour by chromatographic methods. The new compounds were elucidated as 3‐O‐acetyl‐4‐O‐(p‐methoxycinnamoyl)‐α‐L ‐rhamnopyranose ( 1 ), 3‐O‐acetyl‐4‐O‐feruloyl‐α‐L ‐rhamnopyranose ( 2 ), 2‐O‐acetyl‐4‐O‐(O‐methylferuloyl)‐α‐L ‐rhamnopyranose ( 3 ), 2‐O‐acetyl‐4‐O‐(p‐methoxycinnamoyl)‐α‐L ‐rhamnopyranose ( 4 ) by spectral data (1D‐, 2D‐NMR, and MS), respectively.     

Theoretical study of two‐dimensionally fused zinc porphyrins: DFT calculations

Electronic structures of D_4h square‐fused zinc porphyrin sheets of two types ( SA , SB ), where SA is a directly meso‐meso‐, β‐β‐, and β‐β‐linked array and SB is a directly β‐fused array, were compared using density functional theory (DFT). The highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO) of oligomeric SA _n are characteristically delocalized at the cyclooctatetraene‐like sites composed of β‐pyrrolic carbons and their nearest‐neighbor nitrogens. Those of oligomeric SB _n remain solitary monomeric features, reflecting weakly interacting porphyrin units. These two‐dimensionally (2D) square‐fused sheets, especially for SA _n, show effective reduction of both the HOMO–LUMO energy gaps (E_g) and the lowest Q‐like excitation energies because of LUMO's greater stabilization with increasing number of porphyrins than the corresponding one‐dimensionally (1D) linear‐fused tapes. To estimate the minimum value of E_g, the electronic band structures of the infinite‐fused SA _∞ and SB _∞ were examined in detail using modern periodic DFT. Results indicate a full metal for SA _∞, with HOMO and LUMO bands crossing the Fermi level, and a semiconductor with E_g ≈ 0.5 eV for SB _∞. Furthermore, the phonon modes and the electron–phonon coupling (EPC) constant of SA _∞ were calculated throughout the Brillouin zone using density functional perturbation theory (DFPT), yielding a weak EPC constant, λ = 0.35. Within the standard phonon‐mediated BCS mechanism, the superconducting transition temperature, T_c is demonstrated using the McMillan formula, predicting ≈0.5 K. Results show that SA _∞ will become a rare synthetic metal/superconductor without a metal‐insulator transition coming from Peierls lattice instability because it has no serious imaginary phonon modes. © 2009 Wiley Periodicals, Inc. Int J Quantum Chem, 2009     

Bifunctional Heterogeneous Catalysis of Silica–Alumina‐Supported Tertiary Amines with Controlled Acid–Base Interactions for Efficient 1,4‐Addition Reactions

We report the first tunable bifunctional surface of silica–alumina‐supported tertiary amines (SA–NEt₂) active for catalytic 1,4‐addition reactions of nitroalkanes and thiols to electron‐deficient alkenes. The 1,4‐addition reaction of nitroalkanes to electron‐deficient alkenes is one of the most useful carbon–carbon bond‐forming reactions and applicable toward a wide range of organic syntheses. The reaction between nitroethane and methyl vinyl ketone scarcely proceeded with either SA or homogeneous amines, and a mixture of SA and amines showed very low catalytic activity. In addition, undesirable side reactions occurred in the case of a strong base like sodium ethoxide employed as a catalytic reagent. Only the present SA‐supported amine (SA–NEt₂) catalyst enabled selective formation of a double‐alkylated product without promotions of side reactions such as an intramolecular cyclization reaction. The heterogeneous SA–NEt₂ catalyst was easily recovered from the reaction mixture by simple filtration and reusable with retention of its catalytic activity and selectivity. Furthermore, the SA–NEt₂ catalyst system was applicable to the addition reaction of other nitroalkanes and thiols to various electron‐deficient alkenes. The solid‐state magic‐angle spinning (MAS) NMR spectroscopic analyses, including variable‐contact‐time ¹³C cross‐polarization (CP)/MAS NMR spectroscopy, revealed that acid–base interactions between surface acid sites and immobilized amines can be controlled by pretreatment of SA at different temperatures. The catalytic activities for these addition reactions were strongly affected by the surface acid–base interactions.     

Chromenone Glucosides Acylated with Monoterpene Acids from the Leaves of Eucalyptus camaldulensis var. obtusa

Three new chromenone glucosides acylated with monoterpene acids, eucamaldusides A ( 1 ), B ( 2 ), and C ( 3 ), were isolated from the leaves of Eucalyptus camaldulensis var. obtusa, together with the five known compounds ursolic acid lactone, obtusilin, β‐sitosterol glucoside, 4‐hydroxybenzoic acid, and cypellocarpin C. The structures of the new compounds were established by exhaustive 1D‐ and 2D‐NMR spectroscopic studies. Their configuration was determined by measuring the [α]_D of the known methyl esters of the monoterpene acids obtained by methanolysis of 1 – 3 .     

Simultaneous determination of acetylsalicylic acid and salicylic acid in human plasma by isocratic high‐pressure liquid chromatography with post‐column hydrolysis and fluorescence detection

A selective, sensitive and rapid high‐performance liquid chromatography method with post‐column hydrolysis and fluorescence detection was developed for the simultaneous quantification of acetylsalicylic acid and its metabolite salicylic acid in human plasma. Following the addition of 2‐hydroxy‐3‐methoxybenzoic acid as internal standard and simple protein precipitation with acetonitrile, the analytes were separated on a ProntoSIL 120 C₁₈ ace‐EPS column (150 × 2 mm, 3 µm) protected by a C₈ guard column (5 µm). The mobile phase, 10 mm formic acid in water (pH 2.9) and acetonitrile (70:30, v/v), was used at a flow rate of 0.35 mL/min. After on‐line post‐column hydrolysis of acetylsalicylic acid (ASA) to salicylic acid (SA) by addition of alkaline solution, the analytes were measured at 290 nm (λ_ex) and 400 nm (λ_em). The method was linear in the concentration ranges between 0.05 and 20 ng/μL for both ASA and SA with a lower limit of quantification of 25 pg/μL for SA and 50 pg/μL for ASA. The limit of detection was 15 pg/μL for SA and 32.5 pg/μL for ASA. The analysis of ASA and SA can be carried out within 8 min; therefore this method is suitable for measuring plasma concentrations of salicylates in clinical routine. Copyright © 2012 John Wiley & Sons, Ltd.     

Effect of Functionalized Groups on Gas‐Adsorption Properties: Syntheses of Functionalized Microporous Metal–Organic Frameworks and Their High Gas‐Storage Capacity

The microporous metal–organic framework (MMOF) Zn₄O(L1)₂ ? 9 DMF ? 9 H₂O ( 1‐H ) and its functionalized derivatives Zn₄O(L1‐CH₃)₂ ? 9 DMF ? 9 H₂O ( 2‐CH₃ ) and Zn₄O(L1‐Cl)₂ ? 9 DMF ? 9 H₂O ( 3‐Cl ) have been synthesized and characterized (H₃L1=4‐[N,N‐bis(4‐methylbenzoic acid)amino]benzoic acid, H₃L1‐CH₃=4‐[N,N‐bis(4‐methylbenzoic acid)amino]‐2‐methylbenzoic acid, H₃L1‐Cl=4‐[N,N‐bis(4‐methylbenzoic acid)amino]‐2‐chlorobenzoic acid). Single‐crystal X‐ray diffraction analyses confirmed that the two functionalized MMOFs are isostructural to their parent MMOF, and are twofold interpenetrated three‐dimensional (3D) microporous frameworks. All of the samples possess enduring porosity with Langmuir surface areas over 1950 cm² g^?1. Their pore volumes and surface areas decrease in the order 1‐H > 2‐CH₃ > 3‐Cl . Gas‐adsorption studies show that the H₂ uptakes of these samples are among the highest of the MMOFs (2.37 wt % for 3‐Cl at 77 K and 1 bar), although their structures are interpenetrating. Furthermore, this work reveals that the adsorbate–adsorbent interaction plays a more important role in the gas‐adsorption properties of these samples at low pressure, whereas the effects of the pore volumes and surface areas dominate the gas‐adsorption properties at high pressure.     

Synthesis and Crystal Structure of Two Succinato‐Bridged Macrocyclic Nickel(II) Complexes

Two dinuclear succinato‐bridged nickel(II) complexes [Ni(RR‐L)]₂(μ‐SA)(ClO₄)₂ ( 1 ) and [Ni(SS‐L)]₂(μ‐SA)(ClO₄)₂ ( 2 ) (L = 5, 5, 7, 12, 12, 14‐hexamethyl‐1, 4, 8, 11‐tetraazacyclotetradecane, SA = succinic acid) were synthesized and characterized by EA, Circular dichroism (CD), as well as IR and UV/Vis spectroscopy. Single crystal X‐ray diffraction analyses revealed that the Ni^II atoms display a distorted octahedral coordination arrangement, and the succinato ligand bridges two central Ni^II atoms in a bis bidentate fashion to form dimers in 1 and 2 . The monomers of {[Ni(RR‐L)]₂(μ‐SA)}²⁺ and {[Ni(SS‐L)]₂(μ‐SA)}²⁺ are connected by O–H ··· O and N–H ··· O hydrogen bonds into a 1D right‐handed and left‐handed helical chain along the b axis, respectively. The homochiral natures of 1 and 2 are confirmed by the results of CD spectroscopy.     

HPW/PDMAEMA‐b‐PMAA/ZIF‐8 Ternary Lamellar Composite and the Photocatalytic Degradation of Methylene Blue

PDMAEMA‐b‐PMAA block copolymers were prepared by the sequential RAFT polymerization of DMAEMA and tBMA, followed by hydrolysis. Phosphotungstic acid (HPW) was anchored to the PDMAEMA blocks through electrostatic interactions and the as‐obtained HPW/PDMAEMA‐b‐PMAA was added to the synthesis of ZIF‐8. During the formation of ZIF‐8, the PMAA blocks coordinated to the Zn²⁺ ions through their carboxy groups, along with the HPW groups that were anchored to the PDMAEMA blocks. In this way, the block copolymer could consolidate the interactions between HPW and ZIF‐8 and prevent the leakage of HPW. Finally, the HPW/PDMAEMA‐b‐PMAA/ZIF‐8 ternary lamellar composite was obtained and the structure of the HPW/PDMAEMA‐b‐PMAA/ZIF‐8 hybrid material was characterized by using powder X‐ray diffraction (PXRD), X‐ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). As a photocatalyst, the HPW/PDMAEMA‐b‐PMAA/ZIF‐8 ternary lamellar composite showed excellent photoactivity for the degradation of methylene blue (MB). The rate of degradation of MB was 0.0240 min^?1, which was 7.5‐times higher than that of commercially available P25 (0.0032 min^?1). In the presence of H₂O₂, the kinetic degradation parameters of the composite reached 0.0634 min^?1, which was about 19.8‐times higher than that of P25.     

Three AgI,CuI and CdII coordination polymers based on the new asymmetrical ligand 2‐{4‐[(1H‐imidazol‐1‐yl)methyl]phenyl}‐5‐(pyridin‐4‐yl)‐1,3,4‐oxadiazole: syntheses,characterization and emission properties

The new asymmetrical organic ligand 2‐{4‐[(1H‐imidazol‐1‐yl)methyl]phenyl}‐5‐(pyridin‐4‐yl)‐1,3,4‐oxadiazole ( L , C₁₇H₁₃N₅O), containing pyridine and imidazole terminal groups, as well as potential oxdiazole coordination sites, was designed and synthesized. The coordination chemistry of L with soft Ag^I, Cu^I and Cd^II metal ions was investigated and three new coordination polymers (CPs), namely, catena‐poly[[silver(I)‐μ‐2‐{4‐[(1H‐imidazol‐1‐yl)methyl]phenyl}‐5‐(pyridin‐4‐yl)‐1,3,4‐oxadiazole] hexafluoridophosphate], {[Ag( L )]PF₆}_n, catena‐poly[[copper(I)‐di‐μ‐iodido‐copper(I)‐bis(μ‐2‐{4‐[(1H‐imidazol‐1‐yl)methyl]phenyl}‐5‐(pyridin‐4‐yl)‐1,3,4‐oxadiazole)] 1,4‐dioxane monosolvate], {[Cu₂I₂( L )₂]·C₄H₈O₂}_n, and catena‐poly[[[dinitratocopper(II)]‐bis(μ‐2‐{4‐[(1H‐imidazol‐1‐yl)methyl]phenyl}‐5‐(pyridin‐4‐yl)‐1,3,4‐oxadiazole)]–methanol–water (1/1/0.65)], {[Cd( L )₂(NO₃)₂]·2CH₄O·0.65H₂O}_n, were obtained. The experimental results show that ligand L coordinates easily with linear Ag^I, tetrahedral Cu^I and octahedral Cd^II metal atoms to form one‐dimensional polymeric structures. The intermediate oxadiazole ring does not participate in the coordination interactions with the metal ions. In all three CPs, weak π–π interactions between the nearly coplanar pyridine, oxadiazole and benzene rings play an important role in the packing of the polymeric chains.     

A Series of Lanthanide Metal–Organic Frameworks with Interesting Adjustable Photoluminescence Constructed by Helical Chains

Based on the isonicotinic acid (HIN=pyridine‐4‐carboxylic acid), seven lanthanide metal–organic frameworks (MOFs) with the formula [Ln(IN)₂L] (Ln=Eu ( 1 ), Tb ( 2 ), Er ( 3 ), Dy ( 4 ), Ho ( 5 ), Gd ( 6 ), La ( 7 ), L=OCH₂CH₂OH) have been synthesized by mixing Ln₂O₃ with HIN under solvothermal conditions, and characterized by single‐crystal X‐ray diffraction, powder X‐ray diffraction, infrared spectroscopy, and fluorescence spectroscopy. Crystal structural analysis shows that compounds 1–6 are isostructural, crystallize in a chiral space group P2₁2₁2₁, whereas compound 7 crystallizes in space group C2/c. Nevertheless, they all consist of new intertwined chains. Simultaneously, on the basis of the above‐mentioned compounds, we have realized a rational design strategy to form the doped Ln MOFs [(Eu_xTb_1?x)(IN)₂L] (x=0.35 ( 8 ), x=0.19 ( 9 ), x=0.06 ( 10 )) by utilizing Tb^III as the second “rare‐earth metal”. Interestingly, the photoluminescence of [(Eu_xTb_1?x)(IN)₂L] are not only adjustable by the ratios of Eu/Tb, but also temperature or excitation wavelength.     

Synthesis of Fluorescent 2,6‐Dicyano‐3,5‐Disubstituted Anilines Using Cellulose Sulfuric Acid in Aqueous Media

The synthesis of some fluorescent 2,6‐dicyano‐3,5‐disubstituted anilines using cellulose sulfuric acid (Cellulose‐SA) as an environmentally benign catalyst in H₂O is described. The one‐pot reaction of 1,3‐diketone and three equiv. of malononitrile was carried out in the presence of one equiv. of a secondary amine, Cellulose‐SA as catalyst, and H₂O as solvent. The photophysical properties (λ_Abs., λ_Flu.) of the synthesized compounds in CH₂Cl₂, MeCN, and MeOH have been measured. The emission spectra of the new compounds in the solid state are also reported.     

Derivatization following hollow‐fiber microextraction with tetramethylammonium acetate as a dual‐function reagent for the determination of benzoic acid and sorbic acid by GC

Derivatization at the injection port following hollow‐fiber‐based liquid–liquid–liquid microextraction with tetramethylammonium acetate as a dual‐function reagent, i.e. an acceptor and derivatization reagent, for the determination of benzoic acid (BA) and sorbic acid (SA) in real samples by GC was developed. BA and SA were extracted from aqueous samples to an organic phase impregnated into the pores of the hollow fiber wall, and then back‐extracted to the acceptor solution located inside the lumen of the hollow fiber. Upon injection, the extracted analytes were quantitatively derivatized to their methyl esters with tetramethylammonium acetate in the GC injection port. Several parameters related to the derivatization and extraction efficiency were optimized. The linearity was satisfactory over a concentration range of 0.1–50 mg/L with r > 0.993 for both analytes. The LODs were 2.0 μg/L for SA and 20 μg/L for BA. The recoveries (83–116%) and precisions (RSDs of 1.2–11.4% (n = 3)) were examined by analyzing real spiked samples. The enrichment factors of BA and SA were 300 and 425. The results demonstrated that this is a simple, rapid, accurate, and sensitive method for the determination of BA and SA in various samples.     

Identification of cis/trans isomers of methyl ester and oxazoline derivatives of unsaturated fatty acids using GC–FTIR–MS

Identification of cis/trans isomers of unsaturated fatty acids cannot usually be achieved by GC-MS (gas chromatography-mass spectrometry) without reference substances. In this study a GC-FTIR-MS system (gas chromatography-Fourier transform-mass spectrometry) was used to identify fatty acid methyl esters (FAMEs) and differentiate between the cis/trans isomers. Besides methyl esters, 2-alkenyl-4,4-dimethyloxazoline derivatives (DMOX), which have been used to locate double bond positions of unsaturated fatty acids, were examined with respect to their suitability for cis/trans differentiation. A combined GC-FTIR-MS system with a wide band (4000–550 cm^?1) mercury cadmium telluride (MCT) detector was used in series and parallel to identify 31 reference unsaturated fatty acids, including 7 pairs of cis/trans isomers. Serum samples of healthy persons and commercially available fish oil were analyzed as examples of complex mixtures. Using splitless injection the detection limit for the less sensitive IR detector was 25 ng/μl in case of the weak cis and trans bands. In the FTIR spectra cis/trans isomers were identified by analysis of bands arising from C? H out-of-plane (oop) bending: for both the FAME and DMOX derivatives cis-1,2-disubstituted double bonds give a strong band near 720 cm^?1 and the corresponding trans isomers near 967 cm^?1. cis Isomers could be identified further by a band at 3012 cm^?1. With the combined data of the GC-FTIR-MS system it is now possible to identify polyunsaturated fatty acids with regard to the discrimination of cis/trans isomers.     

Dinuclear cobalt(II) complexes with double phosphate ester bridges and tetradentate ligands having anisole or quinoline appendages

Phosphate esters provide a rigid and stable polymeric backbone in nucleic acids. Metal complexes with phosphate ester groups have been synthesized as structural and spectroscopic models of phosphate‐containing enzymes. Dinucleating ligands are used extensively to synthesize model complexes since they provide the support required to stabilize such complexes. The crystal structures of two dinuclear Co^II complexes, namely bis(μ‐diphenyl phosphato‐κ²O :O ′)bis({2‐methoxy‐N ,N‐bis[(pyridin‐2‐yl)methyl]aniline‐κ⁴N ,N ′,N ′′,O }cobalt(II)) bis(perchlorate), [Co(C₁₂H₁₀O₄P)₂(C₁₉H₁₉N₃O)₂](ClO₄)₂, and bis(μ‐diphenyl phosphato‐κ²O :O ′)bis({N ,N‐bis[(pyridin‐2‐yl)methyl]quinolin‐8‐amine‐κ⁴N ,N ′,N ′′,O }cobalt(II)) bis(perchlorate), [Co(C₁₂H₁₀O₄P)₂(C₂₁H₁₈N₄)₂](ClO₄)₂, with tetradentate 2‐methoxy‐N ,N‐bis[(pyridin‐2‐yl)methyl]aniline (L ¹) and N ,N‐bis[(pyridin‐2‐yl)methyl]quinolin‐8‐amine (L ²) ligands are reported. The complexes have similar structures, with distorted octahedral geometries around the metal centres. Both are centrosymmetric (Z ′ = 0.5), with the Co^II centres doubly bridged by diphenyl phosphate ester groups. A number of aromatic–aromatic interactions are present and differ between the two complexes as the anisole group in L ¹ is replaced by a quinoline group in L ². A detailed study of these interactions is presented.     

Crystal structures of four δ‐keto esters and a Cambridge Structural Database analysis of cyano–halogen interactions

The revived interest in halogen bonding as a tool in pharmaceutical cocrystals and drug design has indicated that cyano–halogen interactions could play an important role. The crystal structures of four closely related δ‐keto esters, which differ only in the substitution at a single C atom (by H, OMe, Cl and Br), are compared, namely ethyl 2‐cyano‐5‐oxo‐5‐phenyl‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₂N₂O₃, (1), ethyl 2‐cyano‐5‐(4‐methoxyphenyl)‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₂₀H₂₄N₂O₄, (2), ethyl 5‐(4‐chlorophenyl)‐2‐cyano‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₁ClN₂O₃, (3), and the previously published ethyl 5‐(4‐bromophenyl)‐2‐cyano‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₁BrN₂O₃, (4) [Maurya, Vasudev & Gupta (2013). RSC Adv. 3 , 12955–12962]. The molecular conformations are very similar, while there are differences in the molecular assemblies. Intermolecular C—H...O hydrogen bonds are found to be the primary interactions in the crystal packing and are present in all four structures. The halogenated derivatives have additional aromatic–aromatic interactions and cyano–halogen interactions, further stabilizing the molecular packing. A database analysis of cyano–halogen interactions using the Cambridge Structural Database [CSD; Groom & Allen (2014). Angew. Chem. Int. Ed. 53 , 662–671] revealed that about 13% of the organic molecular crystals containing both cyano and halogen groups have cyano–halogen interactions in their packing. Three geometric parameters for the C—X...N[triple‐bond]C interaction (X = F, Cl, Br or I), viz. the N...X distance and the C—X...N and C—N...X angles, were analysed. The results indicate that all the short cyano–halogen contacts in the CSD can be classified as halogen bonds, which are directional noncovalent interactions.     

Determination of cuticular and internal fatty acids of Chorthippus brunneus males and females using HPLC‐LLSD and GC–MS

Insects are of growing significance in veterinary medicine and human healthcare; therefore, an understanding of their biology is very important. The cuticular and internal fatty acid compositions of Chorthippus brunneus males and females have been studied for the first time. The lipids of males and females were separated into classes of compounds using high‐performance liquid chromatography with a laser light scattering detector. The free fatty acid (FFA) fractions obtained by HPLC were silylated and then analyzed by GC–MS. The cuticular lipids of males contained 15 saturated, four unsaturated with even‐numbered and two unsaturated with odd‐numbered carbon chains, FFAs ranging from C8 to C25. The major free fatty acids in males were C16 (20.8%), C18:2 (8.5%), C18:1 (32.9%) and C18 (24.4%). The cuticular lipids of females contained 17 saturated, four monounsaturated and two diunsaturated free fatty acids ranging from C8 to C30. The major cuticular fatty acids in females were C16 (25.1%), C18:2 (6.2%), C18:1 (23.7%) and C18:0 (33.2%). The internal FFAs of males consisted of 20 compounds ranging from C8 to C26. Four of these compounds were detected as major compounds: C16 (14.1%), C18:2 (21.6%), C18:1 (38.0%) and C18 (22.5%). Among 18 internal free fatty acids of females, C16 (22.3%), C18:2 (10.9%), C18:1 (40.2%) and C18 (20.5%) were the most abundant compounds. The following cuticular fatty acids present in the lipids of females were absent in the lipids of males: C26, C27 and C30. On the other hand, only C24 was absent from the cuticular lipids of females. Only C10 and C24 internal fatty acids present in the lipids of males were absent in the lipids of females. Copyright © 2016 John Wiley & Sons, Ltd.     

Impact of the anion and chalcogen on the crystal structure and properties of 4,6‐dimethyl‐2‐pyrimido(thio)nium halides

By the reaction of urea or thiourea, acetylacetone and hydrogen halide (HF, HBr or HI), we have obtained seven new 4,6‐dimethyl‐2‐pyrimido(thio)nium salts, which were characterized by single‐crystal X‐ray diffraction, namely, 4,6‐dimethyl‐2‐oxo‐2,3‐dihydropyrimidin‐1‐ium bifluoride, C₆H₉N₂O⁺·HF₂^? or (dmpH)F₂H, 4,6‐dimethyl‐2‐oxo‐2,3‐dihydropyrimidin‐1‐ium bromide, C₆H₉N₂O⁺·Br^? or (dmpH)Br, 4,6‐dimethyl‐2‐oxo‐2,3‐dihydropyrimidin‐1‐ium iodide, C₆H₉N₂O⁺·I^? or (dmpH)I, 4,6‐dimethyl‐2‐oxo‐2,3‐dihydropyrimidin‐1‐ium iodide–urea (1/1), C₆H₉N₂O⁺·I^?·CH₄N₂O or (dmpH)I·ur, 4,6‐dimethyl‐2‐sulfanylidene‐2,3‐dihydropyrimidin‐1‐ium bifluoride–thiourea (1/1), C₆H₉N₂S⁺·HF₂^?·CH₄N₂S or (dmptH)F₂H·tu, 4,6‐dimethyl‐2‐sulfanylidene‐2,3‐dihydropyrimidin‐1‐ium bromide, C₆H₉N₂S⁺·Br^? or (dmptH)Br, and 4,6‐dimethyl‐2‐sulfanylidene‐2,3‐dihydropyrimidin‐1‐ium iodide, C₆H₉N₂S⁺·I^? or (dmptH)I. Three HCl derivatives were described previously in the literature, namely, 4,6‐dimethyl‐2‐oxo‐2,3‐dihydropyrimidin‐1‐ium chloride, (dmpH)Cl, 4,6‐dimethyl‐2‐sulfanylidene‐2,3‐dihydropyrimidin‐1‐ium chloride monohydrate, (dmptH)Cl·H₂O, and 4,6‐dimethyl‐2‐sulfanylidene‐2,3‐dihydropyrimidin‐1‐ium chloride–thiourea (1/1), (dmptH)Cl·tu. Structural analysis shows that in 9 out of 10 of these compounds, the ions form one‐dimensional chains or ribbons stabilized by hydrogen bonds. Only in one compound are parallel planes present. In all the structures, there are charge‐assisted N⁺—H…X^? hydrogen bonds, as well as weaker C_Ar⁺—H…X^? and π⁺…X^? interactions. The structures can be divided into five types according to their hydrogen‐bond patterns. All the compounds undergo thermal decomposition at relatively high temperatures (150–300 °C) without melting. Four oxopyrimidinium salts containing a π⁺…X^?…π⁺ sandwich‐like structural motif exhibit luminescent properties.