电子直线加速器变盘模型束流动力学的三维计算

本文采用变半径盘电荷模型作束流动力学的三维计算,给出了粒子在各向的位移及其变化速率,以及束流在各相平面的均方根发射度的大小和束流发射度图象.     

电子直线加速器变盘横型束流动力学的三维计算

本文采用交半径盘电荷模型作束流动力学的三维计算,给出了粒子在各向的位移及其变化速率,以及束流在各相平面的均方根发射度的大小和束流发射度图象.     

HLS储存环束流发射度研究

 研究了合肥光源(HLS)储存环束流发射度与其长直线节消色散条件之间的关系；在考虑到H函数的匹配时，计算了储存环最低束流发射度；为光源多种运行模式提供了理论依据。     

束内散射效应下HALF储存环物理参数的优化设计

合肥先进光源（HALF）是我国规划建设的软X射线与VUV衍射极限储存环光源（DLSR）。如何有效地实现衍射极限束流发射度,是DLSR物理设计中的核心问题之一。基于束流发射度演化方程,针对HALF预研项目的储存环物理设计方案,计算了束内散射（IBS）效应带来的发射度增长,研究了DLSR中关键参数选择对IBS造成的发射度增长的影响。研究表明,在中低能DLSR物理设计中需要综合考虑储存环的周长、同步辐射阻尼时间等关键参数,以更好地抑制束流发射度的增长。在此研究基础上,通过综合考虑用户需求与储存环物理要求,提出了HALF当前工程项目的储存环物理设计方案。进一步综合应用束团拉伸、全耦合等措施后,更高效地抑制了HALF储存环内IBS造成的束流发射度增长。     

SFC-CSRm的束流匹配与制备

为了把HIRFL的注入器SFC的引出束流匹配到HIRFL-CSR的主环CSRm, 提出对SFC引出束流进行制备, 以减小其纵向能散和横向发射度. 给出了这种束流制备方法的原理及理论计算结果.     

BEPCⅡ直线加速器发射度测量

BEPCⅡ直线加速器采用改变四极磁铁励磁电流, 测量获取的束流横截面荧光图像得到束流包络, 进而通过对束流包络和励磁电流的拟合计算得到束流发射度和Twiss参数. 在BEPCⅡ直线加速器的改进过程中, 发现并解决了影响发射度测量结果准确性的多个问题, 改进了束流横截面测量方法和发射度计算方法, 提高了测量结果的准确性. 根据BEPCⅡ直线加速器的具体情况, 还编写了束流截面测量程序和发射度计算程序, 提高了发射度的测量和计算速度, 方便了发射度测量实验的使用.     

BEPCⅡ直线加速器发射度测量

BEPCⅡ直线加速器采用改变四极磁铁励磁电流,测量获取的束流横截面荧光图像得到束流包络,进而通过对束流包络和励磁电流的拟合计算得到束流发射度和Twiss参数.在BEPCⅡ直线加速器的改进过程中,发现并解决了影响发射度测量结果准确性的多个问题,改进了束流横截面测量方法和发射度计算方法,提高了测量结果的准确性.根据BEPCⅡ直线加速器的具体情况,还编写了束流截面测量程序和发射度计算程序,提高了发射度的测量和计算速度,方便了发射度测量实验的使用.     

层流平衡相对论电子束束流特性的数值计算

通过对层流平衡相对论电子的运动微分方程组进行数值求解,得到正则角动量在pθ=0,pθ=const.和pθ∝r2三种情况下,束流的传输特性.针对pθ=0的相对论实心电子束,利用数值求解得到了与解析方法一致的结果,从而验证了数值方法的合理性;针对无法用解析方法求解的pθ=0环行电子束、pθ=const.和pθ∝r2的情况,利用数值方法得到了束流和空间极限电流关于波导、电子束结构和二极管电压等参数的变化规律及对轴向导引磁场的要求.计算结果表明:当相对论电子束以层流平衡态传输时,环行束较实心束具有更高的空间极限电流和更低的轴向导引磁场,且当阴极发射面与导引磁场的磁场线垂直时,维持电子束层流平衡所需的轴向导引磁场最低;电子束在有限磁场导引下以层流平衡态传输时,空间极限电流明显大于无限大磁场导引下一维近似的情况.利用数值方法对层流平衡相对论电子束进行理论研究,更全面地揭示了电子束在正则角动量满足不同条件时的束流特性,为设计新型结构的高功率微波器件提供理论参考.     

双谐波高频系统的同步加速器中发射度主导的长束团研究

在质子储存环中,长束团的长期储存要求采用比较平的 bucket 以增加纵向接收度。对于经过相空间冷却的低能散的束流,束流内部的库仑散射作用不能被忽略。本文讨论了对于处在临界能量以下的发射度主导的长束团双谐波高频系统的特性。为了保持束团长度不变,高频电压应作适当的提高以补偿空间电荷效应的作用。初始失配的束流的纵向运动也分别对于单谐波或双谐波系统进行了研究,对于前者失配度为20%时,纵向接收度太小导致经过几个同步周期后就出现明显的束流纤维化和散束。本文还引入了一种空间电荷作用因子和纵向失配度的概念来研究和分析发射度主导的长束团的纵向运动。采用ORBIT程序对FAIR-HESR加速器中的束流纵向运动进行了模拟跟踪计算,并与理论分析进行了比较。     

储存环聚焦结构设计中的比例定律

阐述并证明了储存环聚焦结构设计中的比例定律.即储存环的尺寸按一定比例放大或缩小时,可以保持工作点和束流发射度不变; 介诸存环的能量改变时,其束流发射度将会随能量的平方变化.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.