Effects of off-state alignment in polymer dispersed liquid crystals

Partial off-state alignment of the liquid crystal in polymer dispersed liquid crystal (PDLC) droplets was obtained by the application of electric or magnetic fields during their formation. Photopolymerization was used to induce phase separation of the liquid droplets from monomer/liquid crystal solutions. Substantial director directionality was retained in these PDLC films after removal of the fields used during their formation. This alignment affected both the off-state and the on-state electro-optic properties of the films. Transverse electrical fields (5 to 60 V across a 15 μm thickness) applied during PDLC formation from a solution of E7 (BDH Ltd) in a monomer resulted in PDLC films with progressively lower off-state scattering and lower threshold voltage. Strong longitudinal magnetic fields (9 to 14 T) applied during PDLC formation with these materials resulted in strong polarization effects in the light scattering off-state. In the infrared region, where there is less light scattering than in the visible region, the longitudinally aligned films shows tunable birefringent electro-optic effects while retaining the fast time response characteristics of PDLC films with small droplet sizes.     

Propriétés optiques et thermophysiques de composites polyméres-cristaux liquides (PDLC)

Polymer dispersed liquid crystal (PDLC) films can be switched electrically from a light scattering off-state to a highly transparent on-state. Thin films were prepared via a polymerization-induced phase separation process using electron beam radiation. The liquid crystal (LC)/polymer materials were obtained from blends of a eutectic nematic mixture E7 and a polyester acrylate based polymer precursor. The optical and electrooptical properties of the obtained PDLC films strongly depend on the LC concentration. The LC solubility limit in the polymer matrix and the fractional amount of LC contained in the droplets were determined by calorimetric measurements.     

The fabrication of novel optical diffusers based on UV-cured polymer dispersed liquid crystals

Polymer dispersed liquid crystals (PDLCs) with different sizes of the LC droplets are prepared based on the ultraviolet (UV) light curable acrylate monomers/LCs composites to fabricate the optical diffuser films. To acquire light diffusers with high optical performance, the effects of the monomer structure and the UV light intensity on the micro-structure of the PDLC films are studied. Results show that the PDLC films could exhibit a strong light scattering at the premise of maintaining high transmittance in the visible region. As the LC droplets are spherically dispersed in the polymer networks, when the size of LC droplets is about 3.0 μm, the haze can reach 88.5% and the transmittance is nearly 90.0%, which can be used as a bottom diffuser film. While when the size of LC droplets is about 10.0 μm, the haze and transmittance are 39.2% and 90.2%, respectively; hence, it can be a good choice for a top diffuser film. With the advantages of simple preparation, roll-to-roll industrial production and tunable optical properties, it is supported that the films based on UV-cured PDLC films can be applied as outstanding optical diffuser films in the liquid crystal display industry.     

大分子引发剂分子量对接枝聚合物基体的PDLC电光性能的影响

以可逆加成-断裂链转移(RAFT)、引发转移终止(iniferter)活性自由基聚合相结合的方法,用一步法制备了不同分子量的大分子引发剂RAFT-PS-co-PCMSI(MI),并通过紫外光聚合诱导相分离法制备了以接枝聚合物为基体的聚合物分散液晶(PDLC)膜.研究了不同分子量的MI对PDLC的微观形貌,关闭状态透光率,阈值电压,饱和电压以及记忆效应等方面的影响.研究表明,降低PDLC中MI的分子量,会使得液晶微滴粒径增大,阈值电压(Vth)、饱和电压(Vsat)减小,记忆效应、关闭状态透光率升高.     

Control of liquid crystal droplet configuration in polymer dispersed liquid crystal with macro-iniferter polystyrene

A polystyrene macro-iniferter was applied to control the alignment of liquid crystal molecules at the droplet wall of polymer dispersed liquid crystal (PDLC) films. The aspects of the alignment were monitored by observing the droplet in the PDLC film. With increasing the macro-iniferter polystyrene in the composition, the configuration of LC droplets changes from bipolar to radial. This is because the high concentration of the macro-iniferter polystyrene results in a small surface interaction between the LC and the polymer matrix, which favours the formation of radial configuration. The radial configuration was stable under our conditions. However, increasing the LC and the initiator concentrations resulted in the change from radial to bipolar.     

Light scattering from acrylate-based polymer dispersed liquid crystals: theoretical considerations and experimental examples

A light scattering (LS) study made using acrylate-based polymer dispersed liquid crystals (PDLCs) is presented. The polarized component IVV is measured for blends of a polyacrylate and the liquid crystal (LC) E7 at several compositions. Only the off-state configuration of the droplets with no external fields is considered here. These composites consist commonly of micron-sized nematic LC droplets dispersed in a solid polymer matrix. Theoretical expressions for the scattered intensities in the case of isotropic and anisotropic spherical droplets are given both in the Rayleigh-Gans approximation (RGA) and in the anomalous diffraction approximation (ADA). Series of VV and VH components of the scattering intensities are calculated using the models of Meeten, Stein and coworkers. The model calculations are compared with the light scattering data. This comparison enables us to extract information on the size and the shape of droplets assuming that the size distribution is uniform and that the scattering is due to single droplets, neglecting inter-particle correlation and multiple scattering effects. This paper demonstrates that the LS technique is a useful tool for studying the morphology of PDLC samples and estimating the average size of nematic droplets.     

Studies on the electro-optical and the light-scattering properties of PDLC films with the size gradient of the LC droplets

Polymer dispersed liquid crystal (PDLC) films with the size gradient of the LC droplets were prepared based on the epoxy/acrylate hybrid polymer matrix. The ultraviolet (UV) intensity gradient was induced by the UV-absorbing dye over the thickness of the samples. Taking advantage of the difference between the epoxy monomers and acrylate monomers in polymerisation rates and the UV intensity gradient, the gradient distribution of the LC droplet size was formed in PDLC films. The effect of the size gradient of the LC droplets on the electro-optical and the light-scattering properties of PDLC films was investigated. The results showed that due to the size gradient distribution of the LC droplets, PDLC films could exhibit the strong light scattering in the UV-visible-near infrared (VIS-NIR) region. Consequently, it provides a potential approach for modulating NIR light transmittance.     

Reverse-mode polymer dispersed liquid crystal films prepared by patterned polymer walls

This article proposes a methodology to prepare polymer dispersed liquid crystal (PDLC) films working in the reverse-mode operation, where the ion-doped nematic liquid crystals (NLCs) with negative dielectric anisotropy (Δε) were locked by polymer walls. On-state and off-state of films were controlled by an electric field. In the absence of an electric field, it appears to be transparent. In the field, the homogeneous alignment NLCs form dynamic scattering, giving rise to opaque. The effect of the cylindrical holes with different diameters of photo masks and liquid crystal Δε on the electro-optical properties and transmittance wavelength range of 400–3000 nm light of samples were investigated. It was found that it exhibited very good electro-optical characteristics, high contrast ratio and excellent infrared energy-efficient of films used as switchable windows.     

Temperature dependence of electro-optical characteristics of polymer dispersed liquid crystal films

Polymer dispersed liquid crystal (PDLC) films consist of microdroplets of a liquid crystal dispersed in a polymer matrix. Their applications are based on the electrically controllable light scattering properties of the liquid crystal droplets. The effects of temperature on the electro-optical properties of PDLC films have been rarely investigated. In this work, we studied the light transmission on varying the temperature and frequency. It was observed that the transmission at a fixed voltage decreased with increasing temperature above 43°C, independent of frequency. We examined possible origins of this unusual dependence of the transmission on the temperature. It was concluded that conductivity effects due to free ions newly created at high temperatures could be responsible for the unusual behaviour observed.     

Temperature dependence of electro-optical characteristics of polymer dispersed liquid crystal films

Polymer dispersed liquid crystal (PDLC) films consist of microdroplets of a liquid crystal dispersed in a polymer matrix. Their applications are based on the electrically controllable light scattering properties of the liquid crystal droplets. The effects of temperature on the electro-optical properties of PDLC films have been rarely investigated. In this work, we studied the light transmission on varying the temperature and frequency. It was observed that the transmission at a fixed voltage decreased with increasing temperature above 43°C, independent of frequency. We examined possible origins of this unusual dependence of the transmission on the temperature. It was concluded that conductivity effects due to free ions newly created at high temperatures could be responsible for the unusual behaviour observed.     

Liquid Crystal-Polymer Composite Materials

Polymer dispersed liquid crystal (PDLC) films can be switched electrically from a light-scattering off-state to a highly transparent on-state. Thin films were prepared via a polymerization-induced phase separation process, using electron beam radiation. The liquid crystal (LC)/polymer materials were obtained from blends of an eutectic nematie mixture E7 and a polyester acrylate-based polymer precursor. The optical and electro-optical properties of the PDLC films obtained depend strongly on the LC concentration. The LC solubility limit in the polymer matrix and the fractional amount of LC contained in the droplets were determined by means of calorimetrie measurements.     

Polymer-dispersed liquid crystal composites for bio-applications: thermotropic,surface and optical properties

Polymer-dispersed liquid crystal (PDLC) systems based on polysulfone as carrying matrix and 4-cyano-4?-pentylbiphenyl (5CB) liquid crystal (LC) were obtained as thin transparent films. The PDLC films were prepared by solvent- and thermally induced phase separation methods, with various compositions in the two components. Information on the phase separation was obtained by polarised light optical microscopy, differential scanning calorimetry and scanning electron microscopy. The PDLC composites show well-defined droplets of submicrometric size, around 650 nm for a medium content of LC and around 250 nm for a low one. The droplets show a radial configuration and a homeotropic alignment of the LC molecules within. By contact angle measurement and surface free energy calculations, it was established that self-assembling of aliphatic units of the two composite components, at droplet interface, is the driving force of the homeotropic alignment. Moreover, these data indicated the potential biocompatibility of the studied composites. The photophysical behaviour shows a better light emission of the PDLCs containing bigger droplets.     

The relationship between formation kinetics and microdroplet size of epoxy-based polymer-dispersed liquid crystals

Polymer films containing dispersions of liquid crystal microdroplets have considerable potential for use in displays and other light control devices. These polymer-dispersed liquid crystal (PDLC) films operate by electric field control of light scattering, rather than by polarization control as in the case of twisted nematic systems. The scattering characteristics of the PDLC films are determined by the refractive indices of the polymer and liquid crystal and by the size of the microdroplets. We have found that it is possible to regulate the microdroplet size by controlling the droplet formation rate (i.e. the cure kinetics of the film). Using calorimetry and scanning electron microscopy, we determined the influence of cure kinetics on microdroplet size for epoxy-based PDLCs. We found that droplet size increased with increasing cure time constant. However, the relationship changed as cure temperature was varied, perhaps as a result of competing cure processes. We also determined the phase behaviour of the epoxy-based PDLCs. The liquid crystal acted as a plasticizer, depressing the glass transition temperature of the PDLC samples slightly below that of the pure epoxy. The temperature and enthalpy of the nematic to isotropic transition of the liquid crystal material in the microdroplets were both functions of cure temperature. From the transition enthalpy it was possible to estimate a, the fraction of liquid crystal contained in the droplets; we found that a decreased with increasing cure temperature, presumably as a result of greater liquid crystal solubility in the epoxy matrix at higher temperatures.     

Effects of monomer structure on the morphology of polymer networks and the electro-optical properties of polymer-dispersed liquid crystal films

Polymer-dispersed liquid crystal (PDLC) films were prepared by photochemical polymerisation with a series of (meth)acrylate monomers. The effects of monomer structure on the morphology of polymer networks in the PDLC films were studied. The acrylate monomers without sidegroup chain formed uniform polymer networks. The methacrylate monomers with methyl as their sidegroup chains formed lace-like networks. The size of the LC droplets increased with increasing the length of the flexible chain of both methacrylate and acrylate monomers. Meanwhile, the effects of the morphology of the polymer network on the electro-optical properties of PDLC films were also investigated.     

<Superscript>2</Superscript>H-NMR investigation after a polymerisation-induced phase separation process*

Polymer-dispersed liquid crystals (PDLC) are composite materials consisting of micron-sized droplets of liquid crystal dispersed in a polymer matrix. The easiest method to obtain a PDLC film is the polymerisation-induced phase separation process (PIPS). The liquid crystal is mixed with a monomer of low molecular weight and polymerisation is induced by heat or UV light. The increasing molecular weight of the polymer causes the phase separation of liquid crystal from the polymer matrix as micron-sized droplets. In this work, we have studied the structural changes induced in the polymer matrix of a PDLC after the PIPS process by deuterium nuclear magnetic resonance. Two different selectively deuterated monomers have been synthesized and investigated: isobutyl methacrylate (IBMA-d₂) and methyl methacrylate (MMA-d₃). The main results were the disappearance of the characteristic two-site hop in poly-IBMA, due to liquid crystal molecules, and the lack of unreacted MMA molecules in the liquid crystal droplets. In this last case, we found that it is possible to confine temporarily the unreacted MMA molecules within liquid crystal droplets.Abbreviations MMA Methyl methacrylate - IBMA Isobutyl methacrylate - PDLC Polymer-dispersed liquid crystal - PIPS Polymerisation-induced phase separation - ²H-NMR Deuterium nuclear magnetic resonance*Dedicated to Professor V. Bertini for his 70^th birthday     

Computer simulation of elongated bipolar nematic droplets II. External field aligned normal to the droplet axis of symmetry

Numerical results from the modelling and computer simulation of the magnetic-induced director reorientation dynamics in elongated bipolar nematic droplets are presented in this paper. The magnetic field is applied normally to the droplet axis-of-symmetry direction, which is one possible scenario found in applications of polymer dispersed liquid crystal (PDLC) films. This case has not yet been studied numerically, and its understanding is far from complete. The model is composed of the Leslie-Ericksen and Frank continuum theories and is solved in two dimensions since bipolar nematic droplets exhibit mirror symmetry in certain planes. The numerical results replicate frequently reported experimental observations on the performance of PDLC films. These observations include the ubiquitous exponential increase followed by saturation in light transmittance as the external applied field increases, and the exponential increase (decrease) followed by saturation as time increases in the on (off)-state. Furthermore, in contrast to current understanding for both the on- and off-states, the model predicts that the directors in the centre (surface) region of the droplet exhibit a dead time (no dead time) before reorientation. The numerical results presented in this paper provide a better understanding of the director reorientation dynamics in elongated bipolar nematic droplets; this can be used to optimize the design and performance of devices using PDLC films.     

Computer simulation of elongated bipolar nematic droplets II. External field aligned normal to the droplet axis of symmetry

Numerical results from the modelling and computer simulation of the magnetic-induced director reorientation dynamics in elongated bipolar nematic droplets are presented in this paper. The magnetic field is applied normally to the droplet axis-of-symmetry direction, which is one possible scenario found in applications of polymer dispersed liquid crystal (PDLC) films. This case has not yet been studied numerically, and its understanding is far from complete. The model is composed of the Leslie-Ericksen and Frank continuum theories and is solved in two dimensions since bipolar nematic droplets exhibit mirror symmetry in certain planes. The numerical results replicate frequently reported experimental observations on the performance of PDLC films. These observations include the ubiquitous exponential increase followed by saturation in light transmittance as the external applied field increases, and the exponential increase (decrease) followed by saturation as time increases in the on (off)-state. Furthermore, in contrast to current understanding for both the on- and off-states, the model predicts that the directors in the centre (surface) region of the droplet exhibit a dead time (no dead time) before reorientation. The numerical results presented in this paper provide a better understanding of the director reorientation dynamics in elongated bipolar nematic droplets; this can be used to optimize the design and performance of devices using PDLC films.     

Effect of electric field on phase separation of polymer dispersed liquid crystal

The kinetics of the polymerization induced phase separation of liquid crystal (LC)/monomer mixture has been investigated by means of depolarized light intensity technique and polarized light microscope (PLM). To examine the effect of the electric field, a DC electric field was applied across the mixtures during the phase separation process. The kinetic study indicates that the phase separation process is accelerated when the electric field is applied. The morphologies of the formed polymer dispersed liquid crystal (PDLC) films were observed by PLM. The electric field applied during the phase separation process yields the PDLC with small LC domains and fine morphologies. The clearing temperature (T_NI) of the formed PDLC films was measured by the PLM and it is found that the T_NI increases with the applied electric field intensity.     

Control of the microstructure of polymer network and effects of the microstructures on light scattering properties of UV‐cured polymer‐dispersed liquid crystal films

Polymer‐dispersed liquid crystals (PDLC) films were prepared from ultraviolet (UV) irradiation‐induced polymerization of the photopolymerizable monomers in photopolymerizable monomers/nematic liquid crystal (LC) mixtures. The effects of the composition of the mixtures, the curing temperature, and the UV light intensity on the microstructure of the polymer network in the PDLC films were investigated. Furthermore, the effects of the microstructures on the light scattering properties of the PDLC films in the wavelength region of 300–2500 nm were studied experimentally and theoretically based on the combination of three kinds of classical light scattering theories: the Rayleigh‐Gans (RG) approach, the anomalous diffraction (AD) approach, and the geometrical optics (GO) approach. It was found that the sizes of LC domain in PDLC films increased with the increase of the LC content as well as the decrease of the UV curing intensity, while increased at first and then decreased with the increase of the curing temperature. Moreover, smaller LC domain sizes could exhibit strong scattering properties in a smaller VIS wavelength region and the transmittance in NIR region (especially in the wavelength range of 1300–2500 nm) obviously decreased with the increasing sizes of LC domain. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2090–2099, 2008