A novel spinel coating on cobalt‐based Superalloy GH605 via an in‐situ oxidation approach

Cr‐Mn‐O spinel coating was prepared on the surface of cobalt‐based superalloy GH605 via an in‐situ oxidation method in H₂O‐H₂ environment. The composition, morphology, and chemical value state of the oxide spinel coatings were investigated by SEM, EDS, XRD, Raman spectra, and XPS. It indicated that the morphology of coating varied with oxidation temperature, and granular surface appeared when oxidation temperature increased to 1100°C. The formed Cr‐Mn‐O spinel coating was composed of Cr₂O₃ and MnCr₂O₄, and the thickness increased significantly with oxidation temperature. In the coating, Cr element existed in the state of Cr³⁺ ions and Cr⁶⁺ ions, while Mn element only existed in the form of Mn²⁺ ions.     

Changes in the surface structure of Pd/Ta2O5 by oxygen and CO studied using X‐ray Photoelectron Spectroscopy (XPS)

Behaviors of Pd structures with different thicknesses supported by Ta₂O₅/Ta in the reaction with oxygen and CO were studied by XPS and SEM. For the samples with a Pd thickness of 3 nm, a new low‐binding‐energy component appeared in the Pd 3d level upon O₂ exposure at ～200 °C and was reduced in intensity after a subsequent CO exposure at 150 and 200 °C. The change in the Ta 4f state could also be found upon oxygen and CO exposure, indicating that both Pd and the Ta‐oxide substrate participate in the chemical reactions. For the sample with a higher Pd thickness, a positive shift in the Pd 3d level due to the oxidation of Pd was observed after exposure to O₂ at a higher temperature (280 °C). A subsequent CO exposure at ～150 °C could not reduce Pd‐oxide layers, as confirmed by the unchanged Pd 3d spectra after CO treatment, i.e. Pd‐oxide was not reactive for CO oxidation. Copyright © 2010 John Wiley & Sons, Ltd.     

Präparation,Kristallstruktur, Schwingungsspektren und thermische Analyse von Kupfer‐tetrahydrogen‐decaoxo‐diperiodat‐hexahydrat CuH4I2O10·6H2O

On Copper‐tetrahydrogen‐decaoxo‐diperiodate‐hexahydrate CuH₄I₂O₁₀·6H₂O: Crystal Structure, Vibrational Spectroscopy and Thermal Analysis By crystallization from a strongly acidic aqueous solution copper‐tetrahydrogen‐decaoxodiperiodate‐hexahydrate CuH₄I₂O₁₀· 6H₂O has been obtained. In the structure of this compound (S.G. P 2₁/c, Nr.14), Z = 2, a = 1060.2(2) pm, b = 551.1(1) pm, c = 1164.7(2) pm, β = 111, 49(3)°) centrosymmetric [H₄I₂O₁₀]^2— anions in the form of two edge sharing octahedra form layers via hydrogen bonds originating from the acidic, trans‐configurated OH groups of the anions. Raman spectra are given and analyzed with respect to the internal vibrations of the periodate anion. The dehydration of the compound takes place via CuH₄I₂O₁₀·3H₂O and Cu(H₂IO₅)₂ which decomposes at 170 °C to Cu(IO₃)₂.     

Crystal Structure and Characterization of Two Layered Copper(II) Coordination Polymers with Anions of 3‐Phosphonopropionic Acid and (RS)‐2‐Phosphonobutyric Acid

Blue single crystals of Cu[μ₃‐O₃P(CH₂)₂COOH] · 2H₂O ( 1 ) and Cu[(RS)‐μ₃‐O₃PCH(C₂H₅)COOH] · 3H₂O ( 2 ) were prepared in aqueous solutions (pH = 2.5–3.5). 1 crystallizes in space group Pbca (no. 61) with a = 812.5(2), b = 919.00(9), and c = 2102.3(2) pm. Cu²⁺ is fivefold coordinated by three oxygen atoms stemming from [O₃P(CH₂)₂COOH]^2– anions and two water molecules. The Cu–O bond lengths range from 194.0(3) to 231.8(4) pm. The connection between the [O₃P(CH₂)₂COOH]^2– anions and the Cu²⁺ cations yields a polymeric structure with layers parallel to (001). The layers are linked by hydrogen bonds. 2 crystallizes in space group Pbca (no. 61) with a = 1007.17(14), b = 961.2(3), c = 2180.9(4) pm. The copper cations are surrounded by five oxygen atoms in a square pyramidal fashion with Cu–O bonds between 193.6(4) and 236.9(4) pm. The coordination between [O₃PCH(C₂H₅)COOH]^2– and Cu²⁺ results in infinite puckered layers parallel to (001). The layers are not connected by any hydrogen bonds. Each layer contains both R and S isomers of the [O₃PCH(C₂H₅)COOH]^2– dianion. Water molecules not bound to Cu²⁺ are intercalated between the layers. UV/Vis spectra suggest three d–d transition bands at 743, 892, 1016 nm for 1 and four bands at 741, 838, 957, and 1151 nm for 2 , respectively. Magnetic measurements suggest a weak antiferromagnetic coupling between Cu²⁺ due to a super‐superexchange interaction. Thermoanalytical investigations in air show that the compounds are stable up to 95 °C ( 1 ) and 65 °C ( 2 ), respectively.     

Time‐Resolved High and Low Temperature Phase Transitions of the Nanocrystalline Cubic Phase in the Y2O3‐ZrO2 and Fe2O3‐ZrO2 System

The nanocrystalline cubic Phase of zirconia was found to be thermally stabilized by the addition of 2.56 to 17.65 mol % Y₂O₃ (5.0 to 30.0 mol % Y, 95.0 to 70.0 mol % Zr cation content). The cubic phase of yttria stabilized zirconia was prepared by thermal decomposition of the hydroxides at 400°C for 1 hr. 2.56 mol % Y₂O₃‐ZrO₂ was stable up to 800°C in an argon atmosphere. The samples with 4.17 to 17.65 mol % Y₂O₃ were stable to 1200°C and higher. All samples at temperatures between 1450°C to 1700°C were cubic except the sample with 2.56 mol % Y₂O₃ which was tetragonal. The crystallite sizes observed for the cubic phase ranged from 50 to 150 Å at temperatures below 900°C and varied from 600 to 800 nm between 1450°C and 1700°C. Control of furnace atmosphere is the main factor for obtaining the cubic phase of Y‐SZ at higher temperature. Nanocrystalline cubic Fe‐SZ (Iron Stabilized Zirconia) with crystallite sizes from 70 to 137 Å was also prepared at 400°C. It transformed isothermally at temperatures above 800°C to the tetragonal Fe‐SZ and ultimately to the monoclinic phase at 900°C. The addition of up to 30 mol % Fe(III) thermally stabilized the cubic phase above 800°C in argon. Higher mol % resulted in a separation of Fe₂O₃. The nanocrystalline cubic Fe‐SZ containing a minimum 20 mol % Fe (III) was found to have the greatest thermal stability. The particle size was a primary factor in determining cubic or tetragonal formation. The oxidation state of Fe in zirconia remained Fe³⁺. Fe‐SZ lattice parameters and rate of particle growth were observed to decrease with higher iron content. The thermal stability of Fe‐SZ is comparable with that of Ca‐SZ, Mg‐SZ and Mn‐SZ prepared by this method.     

Synthesis,characterization, and optimum reaction conditions of oligo‐2‐[(pyridine‐2‐yl‐methylene) amino] phenol

The reaction conditions of the oxidative polycondensation of 2‐[(pyridine‐2‐yl‐methylene) amino] phenol (2‐PMAP) with air O₂, H₂O₂, and NaOCl were studied in an aqueous alkaline medium between 60 and 90 °C. Oligo‐2‐[(pyridine‐2‐yl‐methylene) amino] phenol (O‐2‐PMAP) was characterized with ¹H NMR, Fourier transform infrared, ultraviolet–visible, size exclusion chromatography (SEC), and elemental analysis techniques. Moreover, solubility testing of the oligomer was performed in polar and nonpolar organic solvents. With the NaOCl, H₂O₂, and air O₂ oxidants, the conversions of 2‐PMAP into O‐2‐PMAP were 98, 87, and 62%, respectively, in an aqueous alkaline medium. According to SEC, the number‐average molecular weight, weight‐average molecular weight, and polydispersity index of O‐2‐PMAP were 2262 g mol^?1, 2809 g mol^?1, and 1.24 with NaOCl, 3045 g mol^?1, 3861 g mol^?1, and 1.27 with air O₂, and 1427 g mol^?1, 1648 g mol^?1, and 1.16 with air H₂O₂, respectively. Also, thermogravimetric analysis showed that O‐2‐PMAP was stable against thermooxidative decomposition. The weight loss of O‐2‐PMAP was 96.68% at 900 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2717–2724, 2004     

High temperature oxidation of HP40 alloy under H2–H2O and air atmospheres: a surface study

In the present work, high temperature oxidation of HP40 alloy was carried out at 1050 °C under H₂–H₂O and air atmospheres; the influence of atmosphere on surface morphology and composition was studied. Octahedral crystals with considerable spalled regions are present on the surface of alloy oxidized under air, the oxide scale composes of MnCr₂O₄, Cr₂O₃ and (Fe, Ni)Cr₂O₄ and spalled regions exhibit base alloy and SiO₂‐rich regions. The surface of alloy oxidized under H₂–H₂O is fully covered by small granular crystals and blade‐type structures without spallation, and the oxide scale composes of MnCr₂O₄ and Cr₂O₃. Moreover, X‐ray photoelectron spectroscopy analysis shows considerable difference in chemical valence states of Mn, Cr and O elements on both alloy surfaces, and hydroxyl compounds exist on the alloy oxidized under H₂–H₂O atmosphere. Copyright © 2017 John Wiley & Sons, Ltd.     

Copper(II)‐Catalyzed Synthesis of N‐Substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones by the Reaction of N‐Substituted‐2‐iodobenzamides with Malononitrile

A novel Cu(OAc)₂·H₂O catalyzed coupling reaction of N‐substituted‐2‐iodobenzamides with malononitrile to afford N‐substituted‐3‐amino‐4‐cyano‐isoquinoline‐1(2H)‐ones is described. The reaction proceeded in DMSO at 90°C for 5 h in nitrogen without external ligands.     

Production of 5‐Hydroxymethylfurfural from Fructose in Ionic Liquid Efficiently Catalyzed by Cr(III)‐Al2O3 Catalyst

A series of metal‐Al₂O₃ catalysts were prepared simply by the conventional impregnation with Al₂O₃ and metal chlorides, which were applied to the dehydration of fructose to 5‐hydroxymethylfurfural (HMF). An agreeable HMF yield of 93.1% was achieved from fructose at mild conditions (100°C and 40 min) when employing Cr(III)‐Al₂O₃ as catalyst in 1‐butyl‐3‐methylimidazolium chloride ([Bmim]Cl). The Cr(III)‐Al₂O₃ catalyst was characterized via XRD, DRS and Raman spectra and the results clarified the interaction between the Cr(III) and the alumina support. Meanwhile, the reaction solvents ([Bmim]Cl) collected after 1^st reaction run and 5^th reaction run were analyzed by ICP‐OES and LC‐ITMS and the results confirmed that no Cr(III) ion was dropped off from the alumina support during the fructose dehydration. Notably, Cr(III)‐Al₂O₃ catalyst had an excellent catalytic performance for glucose and sucrose and the HMF yields were reached to 73.7% and 84.1% at 120°C for 60 min, respectively. Furthermore, the system of Cr(III)‐Al₂O₃ and [Bmim]Cl exhibited a constant stability and activity at 100°C for 40 min and a favorable HMF yield was maintained after ten recycles.     

4‐Fluoro‐2‐(phospho­no­methyl)­benzene­sulfonic acid monohydrate

The title compound, C₇H₈FO₆PS·H₂O, contains both phospho­nic and sulfonic acid functionalities. An extensive network of O—H?O hydrogen bonds is present in the crystal structure. The three acidic protons are associated with the phospho­nate group. Two protons experience typical hydrogen‐bond contacts with the sulfonate‐O atoms, while the third has a longer covalent bond of 1.05 (3) Å to the phospho­nate‐O atom and a short hydrogen‐bond contact of 1.38 (3) Å to the water O atom (all O—H?O angles are in the range 162–175°). The sulfonate group is positioned so that one S—O bond is nearly coplanar with the phenyl ring [torsion angle O—S—C—C ?8.6 (2)°]. The phospho­nate group is oriented approximately perpendicular to the ring [torsion angle P—C—C—C 99.2 (2)°] with one P—O bond anti to the benzyl C—C bond. The mol­ecules pack in layers in the b–c plane with the water mol­ecules in between adjacent pairs of inverted layers.     

3‐(Triphenyl­phospho­ranyl­idene)pentane‐2,4‐dione and dieth­yl 2‐(triphenyl­phospho­ranyl­idene)malonate

The title ylides, 3‐(triphenyl­phospho­ranyl­idene)pentane‐2,4‐dione, C₂₃H₂₁O₂P, (I), and diethyl 2‐(triphenyl­phospho­ranyl­idene)malonate, C₂₅H₂₅O₄P, (II), differ in the conformations adopted by their extended ylide moieties. In (I), one carbonyl O atom is syn and the other is anti with respect to the P atom, the ylide group is nearly planar, with a maximum P—C—(C=O) angle of 18.2 (2)°, and the P—C, C—C and C=O bond lengths are consistent with electronic delocalization involving the O atoms. In (II), both carbonyl O atoms are anti and the ester groups are twisted out of the plane of the near trigonal ylide C atom, reducing delocalization, the largest P—C—(C=O) angle being 30.2 (2)°.     

Crystal Structures,Magnetic Properties and Catecholase‐Like Activities of μ‐Alkoxo‐μ‐Carboxylato Double Bridged Dinuclear and Tetranuclear Copper(II) Complexes

One μ‐alkoxo‐μ‐carboxylato bridged dinuclear copper(II) complex, [Cu₂(L¹)(μ‐C₆H₅CO₂)] ( 1 )(H₃L¹ = 1,3‐bis(salicylideneamino)‐2‐propanol)), and two μ‐alkoxo‐μ‐dicarboxylato doubly‐bridged tetranuclear copper(II) complexes, [Cu₄(L¹)₂(μ‐C₈H₁₀O₄)(DMF)₂]·H₂O ( 2 ) and [Cu₄(L²)₂(μ‐C₅H₆O₄]·2H₂O·2CH₃CN ( 3 ) (H₃L² = 1,3‐bis(5‐bromo‐salicylideneamino)‐2‐propanol)) have been prepared and characterized. The single crystal X‐ray analysis shows that the structure of complex 1 is dimeric with two adjacent copper(II) atoms bridged by μ‐alkoxo‐μ‐carboxylato ligands where the Cu···Cu distances and Cu‐O(alkoxo)‐Cu angles are 3.5 11 Å and 132.8°, respectively. Complexes 2 and 3 consist of a μ‐alkoxo‐μ‐dicarboxylato doubly‐bridged tetranuclear Cu(II) complex with mean Cu‐Cu distances and Cu‐O‐Cu angles of 3.092 Å and 104.2° for 2 and 3.486 Å and 129.9° for 3 , respectively. Magnetic measurements reveal that 1 is strong antiferromagnetically coupled with 2J =‐210 cm^?1 while 2 and 3 exhibit ferromagnetic coupling with 2J = 126 cm^?1 and 82 cm^?1 (averaged), respectively. The 2J values of 1–3 are correlated to dihedral angles and the Cu‐O‐Cu angles. Dependence of the pH at 25 °C on the reaction rate of oxidation of 3,5‐di‐tert‐butylcatechol (3,5‐DTBC) to the corresponding quinone (3,5‐DTBQ) catalyzed by 1–3 was studied. Complexes 1–3 exhibit catecholase‐like active at above pH 8 and 25 °C for oxidation of 3,5‐di‐tert‐butylcatechol.     

Influence of metal core of mixed‐metal carboxylates in preparation of spinel: ZnFe2O(O2CCF3)6 as a single‐source precursor for preparation of ZnFe2O4

The mixed‐metal and mixed‐valance carboxylates of MFe₂O(O₂CCF₃)₆(C₄H₈O)₂(H₂O) (M = Zn, Mn, Cu) and MFe₂O(O₂CCCl₃)₆(C₄H₈O)₂(H₂O) (M = Zn, Fe) were utilized as potential precursors for the preparation of spinel. In the pyrolysis of ZnFe₂O(O₂CCF₃)₆(C₄H₈O)₂(H₂O) in air at 400 °C pure ZnFe₂O₄ is formed, in contrast to pyrolysis of the trichloro derivative, which resulted in the formation of ZnO and Fe₂O₃. In the pyrolysis of MnFe₂O(O₂CCF₃)₆(C₄H₈O)₂(H₂O) in nitrogen, MnFe₂O₄ was the main phase and single oxides were the minor phases. Copyright © 2005 John Wiley & Sons, Ltd.     

Bis­[2‐(di­phenyl­phosphinoyl)­benzene] di­sulfide

The title compound, [2‐Ph₂P(O)C₆H₄S]₂ or C₃₆H₂₈O₂P₂S₂, obtained by electrochemical oxidation of 2‐(di­phenyl­phosphino)­benzene­thiol, has twofold crystallographic symmetry. Principal dimensions include S—S 2.0212 (15) Å, S—C 1.786 (3) Å and C—S—S—C 81.34 (14)°.     

Conformational analysis of the disaccharide methyl α‐d‐mannopyranosyl‐(1→3)‐2‐O‐acetyl‐β‐d‐mannopyranoside monohydrate

The crystal structure of methyl α‐d ‐mannopyranosyl‐(1→3)‐2‐O‐acetyl‐β‐d ‐mannopyranoside monohydrate, C₁₅H₂₆O₁₂·H₂O, ( II ), has been determined and the structural parameters for its constituent α‐d ‐mannopyranosyl residue compared with those for methyl α‐d ‐mannopyranoside. Mono‐O‐acetylation appears to promote the crystallization of ( II ), inferred from the difficulty in crystallizing methyl α‐d ‐mannopyranosyl‐(1→3)‐β‐d ‐mannopyranoside despite repeated attempts. The conformational properties of the O‐acetyl side chain in ( II ) are similar to those observed in recent studies of peracetylated mannose‐containing oligosaccharides, having a preferred geometry in which the C2—H2 bond eclipses the C=O bond of the acetyl group. The C2—O2 bond in ( II ) elongates by ～0.02 Å upon O‐acetylation. The phi (?) and psi (ψ) torsion angles that dictate the conformation of the internal O‐glycosidic linkage in ( II ) are similar to those determined recently in aqueous solution by NMR spectroscopy for unacetylated ( II ) using the statistical program MA′AT, with a greater disparity found for ψ (Δ = ～16°) than for ? (Δ = ～6°).     

Synthesis and Photocatalytic Properties of Nano‐crystalline In2O3

A nano‐crystalline In₂O₃ was synthesized using calcinations methods and was used as a photocatalyst to degrade sulfan blue (SB) dye. In addition, this study addresses the conditions of the degradation and the factors that influenced the catalysis. In₂O₃ was prepared by calcining In(OH)₃ at heat ranges of 100–700 °C for 24 h. The In₂O₃ was characterized using field emission scanning electron microscopy (FE‐SEM), an X‐ray diffractometer (XRD), thermogravimetric analysis (TGA), and high‐resolution X‐ray photoelectron spectroscopy (HR‐XPS). The activities of these samples were tested for the photocatalytic degradation of SB dye. The results indicated that the In(OH)₃ that was calcined at 300 °C for 24 h had the best performance.     

Methyl 3‐(4‐methoxyphenyl)prop‐2‐enoate

The title mol­ecule, C₁₁H₁₂O₃, is almost planar, with an average deviation of the C and O atoms from the least‐squares plane of 0.146 (4) Å. The geometry about the C=C bond is trans. The phenyl ring and –COOCH₃ group are twisted with respect to the double bond by 9.3 (3) and 5.6 (5)°, respectively. The endocyclic angle at the junction of the propenoate group and the phenyl ring is decreased from 120° by 2.6 (2)°, whereas two neighbouring angles around the ring are increased by 2.3 (2) and 0.9 (2)°. This is probably associated with the charge‐transfer interaction of the phenyl ring and –COOCH₃ group through the C=C double bond. The mol­ecules are joined together through C—H?O hydrogen bonds between the methoxy and ester groups to form characteristic zigzag chains extended along the c axis.     

Continuous Flow Reduction of Artemisinic Acid Utilizing Multi‐Injection Strategies—Closing the Gap Towards a Fully Continuous Synthesis of Antimalarial Drugs

One of the rare alternative reagents for the reduction of carbon–carbon double bonds is diimide (HN?NH), which can be generated in situ from hydrazine hydrate (N₂H₄ ? H₂O) and O₂. Although this selective method is extremely clean and powerful, it is rarely used, as the rate‐determining oxidation of hydrazine in the absence of a catalyst is relatively slow using conventional batch protocols. A continuous high‐temperature/high‐pressure methodology dramatically enhances the initial oxidation step, at the same time allowing for a safe and scalable processing of the hazardous reaction mixture. Simple alkenes can be selectively reduced within 10–20 min at 100–120 °C and 20 bar O₂ pressure. The development of a multi‐injection reactor platform for the periodic addition of N₂H₄ ? H₂O enables the reduction of less reactive olefins even at lower reaction temperatures. This concept was utilized for the highly selective reduction of artemisinic acid to dihydroartemisinic acid, the precursor molecule for the semisynthesis of the antimalarial drug artemisinin. The industrially relevant reduction was achieved by using four consecutive liquid feeds (of N₂H₄ ? H₂O) and residence time units resulting in a highly selective reduction within approximately 40 min at 60 °C and 20 bar O₂ pressure, providing dihydroartemisinic acid in ≥93 % yield and ≥95 % selectivity.     

Methyl 4‐O‐β‐l‐fucopyranosyl α‐­d‐­glucopyranoside hemihydrate

The crystal structure of methyl 4‐O‐β‐l ‐fuco­pyran­osyl α‐d ‐gluco­pyran­oside hemihydrate C₁₃H₂₄O₁₀·0.5H₂O is organized in sheets with antiparallel strands, where hydro­phobic interaction accounts for partial stabilization. Infinite hydrogen‐bonding networks are observed within each layer as well as between layers; some of these hydrogen bonds are mediated by water mol­ecules. The conformation of the disaccharide is described by the glycosidic torsion angles: ?_H = ?6.1° and ψ_H = 34.3°. The global energy minimum conformation as calculated by molecular mechanics in vacuo has ?_H = ?58° and ψ_H = ?20°. Thus, quite substantial changes are observed between the in vacuo structure and the crystal structure with its infinite hydrogen‐bonding networks.     

Two new thiophosphoramide structures: N,N′,N′′‐tricyclohexylphosphorothioic triamide and O,O′‐diethyl (2‐phenylhydrazin‐1‐yl)thiophosphonate

The compound N,N′,N′′‐tricyclohexylphosphorothioic triamide, C₁₈H₃₆N₃PS or P(S)[NHC₆H₁₁]₃, (I), crystallizes in the space group Pnma with the molecule lying across a mirror plane; one N atom lies on the mirror plane, whereas the bond‐angle sum at the other N atom has a deviation of some 8° from the ideal value of 360° for a planar configuration. The orientation of the atoms attached to this nonplanar N atom corresponds to an anti orientation of the corresponding lone electron pair (LEP) with respect to the P=S group. The P=S bond length of 1.9785 (6) Å is within the expected range for compounds with a P(S)[N]₃ skeleton; however, it is in the region of the longest bond lengths found for analogous structures. This may be due to the involvement of the P=S group in N—H...S=P hydrogen bonds. In O,O′‐diethyl (2‐phenylhydrazin‐1‐yl)thiophosphonate, C₁₀H₁₇N₂O₂PS or P(S)[OC₂H₅]₂[NHNHC₆H₅], (II), the bond‐angle sum at the N atom attached to the phenyl ring is 345.1°, whereas, for the N atom bonded to the P atom, a practically planar environment is observed, with a bond‐angle sum of 359.1°. A Cambridge Structural Database [CSD; Allen (2002). Acta Cryst. B 58 , 380–388] analysis shows a shift of the maximum population of P=S bond lengths in compounds with a P(S)[O]₂[N] skeleton to the shorter bond lengths relative to compounds with a P(S)[N]₃ skeleton. The influence of this difference on the collective tendencies of N...S distances in N—H...S hydrogen bonds for structures with P(S)[N]₃ and P(S)[O]₂[N] segments were studied through a CSD analysis.