TTF‐TCNQ Functionalized Ormosil Based Electrocatalytic Biosensor: A comparative study on Bioelectrocatalysis

A novel electrocatalytic biosensor for glucose is reported that incorporate encapsulation of tetrathifulvalene‐tetracyanoquinodimethane (TTF‐TCNQ) functionalized organically modified sol gel glass (ormosil). The new ormosil is made using palladium‐linked glycidoxypropyltrimethoxysilane precursor, trimethoxysilane, HCl and TTF‐TCNQ powder at 25 °C. The ormosil is converted into fine powder and incorporated within graphite paste electrode along with glucose oxidase. The bioelectrochemistry of GOD and TTF‐TCNQ functionalized ormosil is examined based on cyclic voltammetry and amperometric measurements. A large electrocatalytic current to the order of 8000 μA/cm² is recorded on the addition of 300 mM glucose. Typical responses of new biosensor are reported. The sensitivity of glucose analysis is found relatively much better as compared to earlier reported glucose biosensors. The role of palladium and TTF‐TCNQ introduction within ormosil and its advantages on bioelectrocatalysis are discussed.     

Congo Red Immobilized on a Silica/Aniline Xerogel: Preparation and Application as an Amperometric Sensor for Ascorbic Acid

Congo red (CR) was immobilized on a silica/aniline xerogel through electrostatic interaction. The dye is strongly retained and is not easily leached from the xerogel matrix. The material containing the adsorbed dye was used to prepare a carbon paste electrode and the electrochemical properties of the hybrid material were investigated using cyclic voltammetry and amperometry. The modified electrode was used to study the electrochemical oxidation of ascorbic acid. The adsorbed dye mediates ascorbic acid oxidation at the solid electrode surface‐solution interface at an anodic potential of 0.18 V at pH 7, in a 0.5 mol L^?1 KCl solution. This novel modified carbon paste electrode shows good analytical performance for the determination of ascorbic acid in commercial Vitamin C tablets.     

Differential selectivity in electrochemical oxidation of ascorbic acid and hydrogen peroxide at the surface of functionalized ormosil-modified electrodes

Functionalized ormosil-modified electrodes have been developed for electroanalytical applications. The functionalized ormosil-modified electrodes are made by encapsulating potassium ferricyanide/potassium ferrocyanide within ormosil film derived from an optimum composition of 3-aminopropyltrimethoxysilane, 2-(3,4-epoxycyclohexyl)ethyl trimethoxysilane and phenyltrimethoxy silane in acidic medium in absence of Nafion/crown ether (system 1), in the presence of Nafion (system 2) and in the presence of dibenzo-18-crown-6 (system 3). Another modified electrode (system 4) is also developed using the reaction product of potassium ferricyanide, 3-aminopropyltrimethoxysilane and either tetrahydrofuran (THF) or cyclohexanone followed by ormosil formation in the presence of 2-(3,4-epoxycyclohexyl)ethyl trimethoxysilane and phenyltrimethoxy silane in acidic medium. The electrochemical oxidation of hydrogen peroxide and ascorbic acid conducted at the surface of these four types of functionalized electrodes shows very interesting observations on the selective sensing of ascorbic acid and peroxide. The results based on cyclic voltammetry justify the relative performances on the kinetics of hydrogen peroxide oxidation and reduction. System 3 shows relatively much better oxidation kinetics of hydrogen peroxide as compared to other three systems with relatively weak reduction kinetics whereas system 4 shows relatively faster reduction kinetics of hydrogen peroxide as compared to other three systems. Similarly system 4 shows excellent response to ascorbic acid whereas system 3 shows insensitivity to ascorbic acid under similar experimental conditions. Typical response curve for the analysis of hydrogen peroxide and ascorbic acid using system 3 and system 4 respectively are reported. The results show that system 3 is the best for probing hydrogen peroxide with lowest detection limit of 0.5 μM without any interference from ascorbic acid as commonly encountered using many conventional and chemically modified electrodes.     

聚苯胺纳米纤维修饰石墨箔电极的制备及电化学性能

以石墨箔(GF)为工作电极, 采用循环伏安法(CV), 通过电化学聚合, 制备了聚苯胺(PANI)纳米纤维修饰GF电极(Nano-PANI/GF). 利用红外光谱(FTIR)研究了Nano-PANI/GF修饰电极上聚合物的组成, 利用扫描电镜(SEM)观测了Nano-PANI/GF修饰电极的表面形貌. 利用循环伏安法研究了Nano-PANI/GF修饰电极在0.1 mol/L磷酸盐缓冲溶液(pH=6.9)中的电化学活性, 发现Nano-PANI/GF修饰电极在中性溶液中有良好的电化学活性. Nano-PANI/GF修饰电极对抗坏血酸(AA)电化学氧化的催化作用结果表明, 在0.2 V(vs. SCE)电位下, 在浓度范围1.7~2.0×10³ μmol/L内, 抗坏血酸的氧化电流与浓度呈良好线性关系, 线性方程式为y=0.00013x+0.0031. 修饰电极对抗坏血酸的最低检测限为1.7 μmol/L(S/N=3).     

Electrochemical Characterization of Polymerized Cresol Red Film Modified Glassy Carbon Electrode and Separation of Electrocatalytic Responses for Ascorbic Acid and Dopamine Oxidation

A cresol red modified glassy carbon electrode was prepared using an electrochemical method. The cyclic voltammograms of the modified electrode indicate the presence of a couple of well-defined redox peaks, and the formal potential shifts in the negative direction with increasing solution pH. The modified electrode exhibits high electrocatalytic activity toward ascorbic acid oxidation, with an overpotential of 300 mV less than that of bare glassy carbon electrodes, and drastic enhancement of the anodic currents. The calibration graph obtained by linear sweep voltammetry for ascorbic acid is linear in the range of 50∼500 µM. The electrode markedly enhances the current response of dopamine and can separate the electrochemical responses of ascorbic acid and dopamine. The separation between the anodic peak potentials of ascorbic acid and dopamine is 190 mV by cyclic voltammetry. The linear sweep voltammetric peak currents for dopamine in the presence of 2 mM ascorbic acid vary linearly with a concentration of between 10 and 100 µM.     

基于溶胶-凝胶技术的聚烯丙胺基二茂铁化学修饰电极的组装及其对抗坏血酸的电催化氧化

将聚烯丙胺基二茂铁与聚苯乙烯磺酸盐生成的离子配合物用乙醇溶解后掺杂到溶胶-凝胶中,将此溶液滴涂在玻碳电极表面,制成化学修饰电极.详细地研究了该修饰电极的电化学性能及其稳定性.实验发现,在0.1mol/L磷酸盐缓冲液(pH=2.5)中,该修饰电极对抗坏血酸的电化学氧化具有很好的催化活性和稳定性.     

Carbon nanotube-modified electrodes for the simultaneous determination of dopamine and ascorbic acid

The voltammetric separation of dopamine and ascorbic acid was studied with cyclic voltammetry at two kinds of carbon nanotube-modified electrodes (coated and intercalated). The anodic peak difference reached 270 mV under the present conditions. The separation mechanism and effect factors were carefully studied. Using various types of surfactants as coating dispersants of carbon nanotubes, it was demonstrated that the charge nature of the surfactants had a strong effect on the electrochemical behavior of dopamine and ascorbic acid. When the oxidation solution of carbon nanotubes was changed from the most commonly used mixed concentrated nitric acid and sulfuric acid (1 + 3 v/v) to dilute nitric acid and to hydrochloric acid, the anodic peak separation value of dopamine and ascorbic acid increased significantly, and it was shown that carboxylic acid groups attached to the carbon nanotubes were an adverse factor for the discrimination of DA from AA. These results indicated that the resolution of DA and AA was mainly attributable to the stereo porous interfacial layer formed from aggregated pores and inner cavities of the carbon nanotubes. The modified electrodes exhibited an attractive ability to measure DA and AA simultaneously and showed good stability and reproducibility.     

纳米金–壳聚糖修饰电极循环伏安法测定抗坏血酸

介绍纳米金–壳聚糖修饰电极的制备方法及其测定抗坏血酸的分析应用。采用电沉积方法,将氯金酸与壳聚糖的混合电解液直接共沉积,制备了壳聚糖–纳米金修饰玻碳电极的电化学传感器。利用循环伏安法研究了抗坏血酸浓度、p H值等对抗坏血酸在修饰电极上的电化学行为的影响。实验结果表明,修饰电极对抗坏血酸具有良好的电催化氧化作用,抗坏血酸浓度在5×10~(–5)~1×10~(–3) mol/L范围内线性良好,回归方程为I_p=0.433 8c+0.881 9,相关系数为0.998 71。该法可指导纳米金–壳聚糖修饰电极的制备及抗坏血酸含量的测定。     

Determination of Anticholinesterase Activity for Pesticides Monitoring Using a Thiocholine Sensor

Abstract

An acetylthiocholine sensor based on a disposable screen-printed carbon electrode has been assembled for measuring organophosphorus and carbamate pesticides in river water samples through the degree of inhibition of the enzyme acetylcholinesterase (AChE). The carbon working electrode surface was modified by deposition of a mediator, tetracyanoquinodimethane (TCNQ), and Nafion. Acetylcholinesterase catalyses the cleavage of acetylthiocholine to thiocholine, which is measured by differential pulse voltammetry and directly related to the enzyme activity. The scan speed, the pulse amplitude of the differential pulse voltammetry and several parameters in the procedure were optimised. An inhibition calibration curve was obtained using carbofuran. The method was also applied to water samples, showing its suitability as a rapid screening assay (15 min per test) for anticholinesterase activity detection.     

聚苯胺薄膜修饰电极对抗坏血酸的电催化氧化

本文表明聚苯胺(PAn)薄膜修饰电极对水溶液中的抗坏血酸(AH_2)在较宽的pH范围和较宽的浓度范围内均有良好的电催化氧化作用, 为EC平行催化过程。利用旋转圆盘电极(RDE)进行了催化过程动力学分析, 求出了催化反应动力学参数。在抗坏血酸浓度10~(-2)～10~(-6) mol·L~(-1)范围内, 催化峰电流与AH_2浓度均成良好的线性关系, 且PAn薄膜修饰电极具有很好的稳定性, 有应用分析抗坏血酸的意义。     

聚多巴胺/多壁碳纳米管/玻璃碳电极上多巴胺的电分析

基于多巴胺（DA）在多壁碳纳米管（MWCNTs）修饰玻璃碳（GC）电极上的电聚合,制得聚多巴胺(PDA)/MWCNTs/GC电极,并对该修饰电极进行了电化学阻抗谱 (EIS)和循环伏安法(CV)表征。 在该修饰电极上,DA呈现良好的电化学行为。在pH=7.4磷酸缓冲溶液中其氧化电流显著高于在裸电极上的响应,且能有效地抑制2.0 mmol/L抗坏血酸(AA)或K4Fe(CN)6的直接电化学响应,表明MWCNTs可增敏信号,且阳离子选择透过性PDA膜可抑制阴离子的电化学干扰。 采用CV实验检测DA,DA氧化的半微分伏安峰高(ipa-sd)与多巴胺浓度在0.08～1.76 μmol/L范围内呈线性关系,在无抗坏血酸和有0.5 mmol/L抗坏血酸共存时的线性回归方程分别为ipa-sd(μA/s1/2)=0.107+0.405c(μmol/L)（r2=0.986）和ipa-sd(μA/s1/2)=0.628+0.649c(μmol/L)(r2=0.992),检测限均为8.0×10-8 mol/L(S/N=3)。 该法用于盐酸多巴胺注射液中多巴胺的快速测定,结果满意。     

The electrochemical copolymerization of 3,4-dihydroxybenzoic acid and aniline at microdisk gold electrode and its amperometric determination for ascorbic acid

The electrochemical copolymerization of 3,4-dihydroxybenzoic acid (3,4-DHBA) and aniline was carried out at microdisk gold electrodes by means of cyclic voltammetric sweep. The polymer obtained on the electrode shows good electrochemical activity and high stability even though in neutral and weakly basic media. It was found that the response current of ascorbic acid was greatly enhanced at this composite polymer electrode. Moreover, the anodic overpotential was significantly reduced for about 200 mV (vs. SCE) compared with that obtained at bare gold electrodes. The electrode exhibits a rapid current response (less than 2 s) and a high sensitivity (0.21 AM(-1) cm(-2)). The dependence of response currents on the concentration of ascorbic acid was linear in the range of 1.0x10(-4)-1.0x10(-2) M. In addition this composite polymer modified electrode exhibits a high electrode stability for a long-term use.     

Autocatalytic Character of Anodic Polymerization of Aniline in Water–Organic Acid Solutions

A cyclic voltammetry study shows the anodic polymerization of aniline in 2 M HClO₄ water–acetonitrile solutions to proceed via an EC: EC mechanism. In the chemical reaction, pernigraniline catalyzes the aniline oxidation, recovering from emeraldin in the second stage of the electrochemical process.     

Application of Carbon Paste Electrode Modified with Carbon Nanofibres/Polyaniline/Platinum Nanoparticles as an Electrochemical Sensor for the Determination of Bezafibrate

The present study deals with the development of an electrochemical sensor for quantitative determination of Bezafibrate (BZF) based on carbon nanofibers/polyaniline/platinum nanoparticles modified carbon paste electrode (CNF/PANI/Pt/CPE). BZF is a fibric acid derivative and is used largely in the treatment of lipid disorders. The nanocomposite was synthesized by in situ polymerization of aniline using ammonium persulphate and platinum nanoparticles were uniformly decorated on the CNF/PANI surface by reducing hexachloroplatinic acid using sodium borohydride. The electrochemical response of BZF at CNF/PANI/Pt/CPE was studied using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The above study resulted into significant improvement of the electrochemical signal towards the oxidation of BZF, revealing that the oxidation process is highly favorable at the surface of modified electrode. The anodic peak current I_p (μA) is found to be linearly dependent on BZF concentration in the range of 0.025 μM to 100 μM with a detection limit of 2.46 nM. The practical analytical utilities of the sensor were investigated by performing the experiments on synthetic pharmaceutical formulations, human blood serum and urine samples which offered good recovery, suggesting the high efficacy and authenticity of CNF/PANI/Pt/CPE sensor for BZF determination.     

Fabrication of Poly(allylamine)ferrocene Monolayer Based on Electrostatic Interaction and Its Electrocatalytic Oxidation of Ascorbic Acid

A poly(allylamine)ferrocene monolayer was built on the surface of gold electrode modified with negatively charged alkanethiol based on electrostatic interaction. The electrochemical behavior of the modified electrode was characterized by cyclic voltammetry in detail. The modified electrode was shown to exhibit excellent electrocatalytic response to the oxidation of ascorbic acid. The anodic overpotential was reduced by about 170 mV compared with that obtained at a bare gold electrode. The modified electrode possesses several attractive features, such as simple preparation, fast response and good chemical and mechanical stability.     

Development of screen-printed carbon electrodes,chemically modified with cobalt phthalocyanine,for electrochemical sensor applications

A method is described for the production of screen-printed graphite electrodes and also for similar electrodes chemically modified with the electrocatalyst cobalt phthalocyanine. Using cyclic voltammetry, the electrochemical behaviour of these electrodes towards ascorbic acid, reduced glutatione and coenzyme A (CoA-SH) was investigated. The modified electrodes were found to give significant decreases in the over-potential required for the oxidation of these species at carbon electrodes. The useful electrochemical window for the unmodified carbon film electrodes was ?1.08 V to +0.85 V vs. SCE, using 1 μA background current cut-off points.Amperometry in stirred solutions was used to investigate the hydrodynamic behaviour of the electrodes and their calibration performance. The limits of detection for ascorbic acid and reduced glutathione at the modified films were 5 × 10^?8 and 1 × 10^?7 M, respectively. The calibration graphs were also linear up to 2 mM concentrations of both analytes. Using differential-pulse voltammetry, linear calibration graphs were obtained for both species up to 2.5 mM. This technique was also used to assess the reproducibility of the electrode manufacture; the coefficient of variation was 2.8% for 1.49 mM ascorbic acid and 6.9% for 0.92 mM reduced glutathione.     

Fabrication and characterization of poly 2-napthol orange film modified electrode and its application to selective detection of dopamine

The present work is based on the use of a redox mediator containing an azo group for the selective determination of dopamine in the presence of uric acid and ascorbic acid by electrochemical method. A modified electrode was prepared by electrochemical polymerization of the poly 2-napthol orange film (P2NO) on the paraffin wax-impregnated graphite electrode (PIGE) by applying potential between ?0.6 and 0.8 V at scan rate of 50 mV s^?1 for 30 segments. The modified P2NO film electrode was characterized by ATR-IR spectroscopy, FE-SEM, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), hydrodynamic voltammetry (HDV), and chronoamperometry (CA). The P2NO film modified electrode exhibited selective determination of dopamine in the presence of uric acid and ascorbic acid, and the electrocatalytic activity for oxidation of dopamine was excellent. The linear range for the determination of dopamine was 0.6 to 250 μM with a limit of detection of 0.13 μM. The modified P2NO electrode showed good stability and reproducibility. The modified electrode was used for real sample analysis such as human blood serum, rat blood serum, and pharmaceutical samples (dopamine hydrochloride injection). The results obtained were found to be satisfactory.     

水杨酸分子印迹膜电化学传感器的制备

以水杨酸为模板分子,采用循环伏安法电聚合形成聚吡咯膜,以固定电位过氧化法去除印迹分子,制备了水杨酸分子印迹膜电极.本印迹电极能促进水杨酸电氧化过程,有效地避免结构类似物(如苯甲酸)对其测定的干扰.循环伏安法用于电化学检测,当富集时间为10 min,磷酸盐缓冲溶液的pH=6.86 时,在1.0×10-6～2.0×10-3 mol/L浓度范围内,水杨酸氧化峰电流与其浓度呈良好的线性关系,检出限为0.8 μmol/L, 用分子印迹膜电极对加标样品进行分析,回收率为94.6%～103.4%.     

Amperometric sensor for the determination of ascorbic acid based on Cobalt hexacyanoferrate modified electrode fabricated through a new route

A new approach was attempted to prepare a chemically modified electrode using Cobalt hexacyanoferrate (CoHCF) as the redox mediator and to study its stability and electrocatalytic activity for ascorbic acid (AA) oxidation. The basic principle underlying the electrode modification is the coordination of cobalt ion with the amino nitrogen of aniline adsorbed on the surface of a graphite rod. This surface was subsequently derivatized with ferrocyanide to get CoHCF film on the electrode surface. The CoHCF modified electrode as prepared above was characterized using cyclic voltammetry. The effect of scan rate, supporting electrolyte and pH of the medium on the performance of the modified electrode was investigated. The CoHCF modified electrode exhibited good electrocatalytic activity towards the oxidation of ascorbic acid and gave a linear response from 5.52 x 10(-5) M to 3.23 x 10(-2) M with a correlation coefficient of 0.9929. The detection limit was found to be 3.33 x 10(-5) M. Hydrodynamic voltammetry and chronoamperometry studies for the oxidation of ascorbic acid were also carried out. The electrode was highly stable and exhibited good reproducibility. This modified electrode was also applied for the determination of ascorbic acid in commercial samples.     

Application of nickel phosphate nanoparticles and VSB-5 in the modification of carbon paste electrode for electrocatalytic oxidation of methanol

Carbon paste electrodes were modified by nickel phosphate nanoparticles and nickel phosphate Versailles Santa Barbara-5 molecular sieves. Then, transition metal ions of Ni(II) were incorporated to the nickel phosphate by immersion of the modified electrode in a 0.1-M nickel chloride solution. The electrochemical behaviors of the modified electrodes were studied using cyclic voltammetry. These modified electrodes were used as anode for the electrocatalytic oxidation of methanol in alkaline medium. The influence of some parameters such as different molecular sieves, scan rate of potential, and methanol concentration was investigated on the anodic peak height of the methanol oxidation. The best result was obtained by nickel phosphate nanoparticles.