Amperometric determination of xanthine in fish meat by zinc oxide nanoparticle/chitosan/multiwalled carbon nanotube/polyaniline composite film bound xanthine oxidase

Xanthine oxidase (XOD) was immobilized on a composite film of zinc oxide nanoparticle/chitosan/carboxylated multiwalled carbon nanotube/polyaniline (ZnO-NP/CHIT/c-MWCNT/PANI) electrodeposited over the surface of a platinum (Pt) electrode. A xanthine biosensor was fabricated using XOD/ZnO-NP/CHIT/c-MWCNT/PANI/Pt as working electrode, Ag/AgCl as reference electrode and Pt wire as auxiliary electrode connected through a potentiostat. The ZnO-NPs were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), and the enzyme electrode was characterized by cyclic voltammetry, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 4 s at 0.5 V potential, pH 7.0, 35 °C and linear range 0.1-100 μM with a detection limit of 0.1 μM. The enzyme electrode was employed for determination of xanthine in fish meat during storage. The electrode lost 30% of its initial activity after 80 uses over one month, when stored at 4 °C.     

Development of an amperometric sulfite biosensor based on a gold nanoparticles/chitosan/multiwalled carbon nanotubes/polyaniline-modified gold electrode

A sulfite oxidase (SOx) purified from leaves of Syzygium cumini (Jamun) was immobilized covalently onto a gold nanoparticles (AuNPs)/chitosan (CHIT)/carboxylated multiwalled carbon nanotubes (cMWCNTs)/polyaniline (PANI) composite that was electrodeposited onto the surface of a gold (Au) electrode. A novel and highly sensitive sulfite biosensor was developed that used this enzyme electrode (SOx/AuNPs/CHIT/cMWCNT/PANI/Au) as the working electrode, Ag/AgCl as the standard electrode, and Pt wire as the auxiliary electrode. The modified electrode was characterized by Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS) before and after the immobilization of the SOx. The sensor produced its optimum response within 3 s when operated at 50 mVs⁻¹ in 0.1 M phosphate buffer, pH 7.0, and at 35 °C. The linear range and detection limit of the sensor were 0.75–400 μM and 0.5 μM (S/N = 3), respectively. The biosensor was employed to determine sulfite levels in fruit juices and alcoholic beverages. The enzyme electrode was used 300 times over a period of three months when stored at 4 °C.     

A new enzyme electrode based on ascorbate oxidase immobilized in gelatin for specific determination of l-ascorbic acid

A biosensor for the specific determination of l-ascorbic acid in fruit juices and vitamin C tablets was developed using ascorbate oxidase (EC 1.10.3.3) from cucumber (Cucumis sativus L.) in combination with a dissolved oxygen probe. Ascorbate oxidase immobilized with gelatin using glutaraldehyde and fixed on pretreated teflon membrane served as an enzyme electrode. The phosphate buffer (50 mM, pH 7.5) and 35 degrees C were established as providing the optimum conditions. The biosensor response depends linearly on l-ascorbic acid concentration between 5.0x10(-5) and 1.2x10(-3) M with a response time 45 s. The biosensor is stable for more than 2 months, while more than 200 assays were performed. The results obtained for fruit juices and tablets were compared with DCIP (2,6 dichlorophenolindophenol) method.     

An amperometric glucose biosensor based on glucose oxidase immobilized in electropolymerized poly(o-aminophenol) and carbon nanotubes composite film on a gold electrode.

An amperometric glucose biosensor is developed that is based on immobilization of glucose oxidase (GOD) in a composite film of poly(o-aminophenol) (POAP) and carbon nanotubes (CNT), which are electrochemically co-polymerized at a gold (Au) electrode. Because of the high surface per volume ratio and excellent electrical conductivity of CNT, the biosensor based on an Au/POAP/CNT/GOD electrode has lower detection limit (0.01 mM), larger maximum response current (0.24 mA cm(-2)) and higher sensitivity (11.4 mA M(-1) cm(-2)) than the values of the biosensor based on an Au/POAP/GOD electrode. Additionally, the biosensor shows fast response time, large response current, and good anti-interferent ability for ascorbic acid, uric acid and acetaminophen. Good reproducibility and stability of the biosensor are also observed.     

Electropolymerized network of polyamidoamine dendron-coated gold nanoparticles as novel nanostructured electrode surface for biosensor construction

Polyfuntionalized gold nanoparticles were prepared by using 2-mercaptoethanesulfonic acid, p-aminothiophenol and cysteamine core polyamidoamine G-4 dendron as capping ligands. The nanoparticles were electropolymerized on a Au electrode surface through the formation of a bisaniline-cross-linked network. The enzyme tyrosinase was further crosslinked on this nanostructured matrix. The enzyme electrode, poised at -100 mV, was used for the amperometric quantification of cathecol. The biosensor showed a linear response from 50 nM to 10 μM cathecol, with a low detection limit of 20 nM and a sensitivity of 1.94 A M(-1) cm(2). The electrode retained 96% and 67% of its initial activity after 16 and 30 days of storage at 4 °C under dry conditions.     

Electrodeposited Cu‐Au Alloy Nanoparticles for Uric Acid Electrochemical Biosensor with Quick Response

A uric acid (UA) electrochemical biosensor based on the Cu‐Au alloy nanoparticles (NPs) and uricase was developed. The electrodeposition technique of Cu‐Au alloy NPs was selected to be a convenient potentiostatic method at –0.8 V in a single solution containing both Au(III) and Cu²⁺. Cyclic voltammetry and scanning electron microscopy proved the successful deposition of Cu‐Au alloy NPs. EIS demonstrated the good conductivity of Cu‐Au alloy NPs. The enzyme was immobilized on the surface of Cu‐Au alloy NPs modified electrode by casting with chitosan solution. The ultimate biosensor showed linear amperometric response towards UA in the concentration range of 3.0 to 26.0 μM with a detection limit of 0.8 μM. The main feature of the biosensor was its short response time, which was attributed to the good conductivity of Cu‐Au alloy NPs. Furthermore, the biosensor could avoid the interference of ascorbic acid and oxygen.     

An amperometric biosensor based on acetylcholinesterase immobilized onto iron oxide nanoparticles/multi-walled carbon nanotubes modified gold electrode for measurement of organophosphorus insecticides

An acetylcholinesterase (AChE) purified from maize seedlings was immobilized covalently onto iron oxide nanoparticles (Fe₃O₄NP) and carboxylated multi walled carbon nanotubes (c-MWCNT) modified Au electrode. An organophosphorus (OP) biosensor was fabricated using this AChE/Fe₃O₄/c-MWCNT/Au electrode as a working electrode, Ag/AgCl as standard and Pt wire as an auxiliary electrode connected through a potentiostat. The biosensor was based on inhibition of AChE by OP compounds/insecticides. The properties of nanoparticles modified electrodes were studied by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), cyclic voltammograms (CVs) and electrochemical impedance spectroscopy (EIS). The synergistic action of Fe₃O₄NP and c-MWCNT showed excellent electrocatalytic activity at low potential (+0.4 V). The optimum working conditions for the sensor were pH 7.5, 35 °C, 600 μM substrate concentration and 10 min for inhibition by pesticide. Under optimum conditions, the inhibition rates of OP pesticides were proportional to their concentrations in the range of 0.1–40 nM, 0.1–50 nM, 1–50 nM and 10–100 nM for malathion, chlorpyrifos, monocrotophos and endosulfan respectively. The detection limits were 0.1 nM for malathion and chlorpyrifos, 1 nM for monocrotophos and 10 nM for endosulfan. The biosensor exhibited good sensitivity (0.475 mA μM⁻¹), reusability (more than 50 times) and stability (2 months). The sensor was suitable for trace detection of OP pesticide residues in milk and water.     

Electrochemical synthesis of polyaniline in surface-attached poly(acrylic acid) network, and its application to the electrocatalytic oxidation of ascorbic acid

Acrylic acid was first electropolymerized on the surface of a gold electrode. Then, polyaniline (PANI) was electrodeposited on the poly(acrylic acid) (PAA) network to give a PANI–PAA composite film. Scanning electron microscopy and electrochemical studies confirmed the formation of PANI–PAA composite which exhibited excellent electroactivity over a wide pH range. The electro-oxidation of ascorbic acid (AA) was studied in detail. The modified electrode exhibits significantly reduced oxidation overpotential. The response towards AA is linear in the range 1.0 μM to 9.3 mM (R?=?0.9997, n?=?33) at a potential of 0.1 V (vs. SCE). The sensitivity is 207 μA mM^-1 cm^-2, and the detection limit is 1.0 μM (S/N?=?3). Interferences by uric acid and dopamine are negligible. The electrode thus enables sensitive and selective determination of AA, with a performance superior to many other PANI–based ascorbate sensors.     

Ascorbic acid biosensor using ascorbate oxidase immobilized on alkylamine glass beads

A biosensor for ascorbic acid based on enzyme kinetics of ascorbate oxidase (E.C.1.10.3.3.) was developed. The enzyme was extracted fromCucurbita maxima, or jerimun and immobilized by covalent bounding, using glutaradehyde as a bifunctional agent, on alkylamine glass beads, with and without enzyme active site protection. A low-cost, home-made oxygen electrode was applied as a transducer. The system has sensitivity from 62.5 up to 500 μM of ascorbic acid with satisfactory operation for more than 2 mo.     

A Highly Sensitive and Selective Multiwall Carbon Nanotubes/Nafion/Au Microarrays Electrode for Dopamine Determination

This work presents the fabrication of Nafion (Nf) or Nafion/Multiwalled Carbon Nanotubes (Nf/MWCNTs) modified gold microarray (Au‐µA) and macro‐(Au‐M)electrode biosensors. The surface morphologies of the above electrodes were examined using SEM. The catalytic properties of the above electrodes towards dopamine were tested using square wave voltammetric technique. The Nf/MWCNT/Au‐µA electrode exhibited a wide range (0.1–1000 nM) of linearity among the other electrodes. The LOD of Nf/MWCNT/Au‐µA electrode was 50 pM for dopamine in the presence of 5000 µM ascorbic acid. Therefore, the Nf/MWCNT/Au‐µA biosensor was applied for the determination of dopamine in human serum.     

Highly Sensitive Enzyme-free Sensor Based on a Carbon Paste Electrode Modified with Binary Zinc Oxide/Polyaniline Nanocomposites for Dopamine,Ascorbic Acid and Uric Acid Sensing

Hybrid composites ZnO/PANI were facily synthesized by a sonication process at room temperature. This procedure is non-expensive, time/energy saving and environmentally safe. The as-prepared ZnO/PANI were characterized by FTIR, UV-vis spectroscopies and SEM in order to investigate the structure and morphology of the studied composites. The samples were used to modify carbon paste electrode (CPE) in order to develop electrochemical biosensors (ZnO/PANI/CPE). The sensing properties of the nanoparticles were evaluated for dopamine, ascorbic acid and uric acid non-enzymatic detection. The effect of percentage of polyaniline in the composites and the effect of calcination on the biosensor's response were also examined in the present study. It was revealed that the existence of PANI in ZnO/PANI/CPE largely enhanced the electroactive surface area and therefore the sensitivity for electrochemical sensing. A good electrochemical behavior was noted for ZnO/40 wt% PANI-cal/CPE modified electrode toward DA, AA and UA oxidation. The electroactive surface area of the previously mentioned modified electrode (0.235 cm²) was two times higher than that of the bare electrode (0.117 cm²). The liner relationships between current intensities and concentrations were found to be 0.01–1.4 mM, 0.1–1.3 mM and 0.01–0.12 mM, with detection limit of 0.029 mM, 0.063 mM and 0.007 mM, for DA, AA and UA respectively. In the mixtures of ascorbic acid (AA), dopamine (DA) uric acid (UA) and glucose (Glu) the sensor showed high selectivity of DA with low interference of ascorbic acid by a current change of 14 %. The as-prepared ZnO/PANI/CPE biosensor displayed a good reproducibility and stability.     

Preparation of Au Nanoparticles Decorated Polyaniline Nanotube and Its Catalytic Oxidation to Ascorbic Acid

With sulfonated electrospun polystyrene fiber as a template, uniform polyaniline(PANI) nanotubes were fabricated via polymerization of aniline followed by template removal. Au nanoparticles(Au_nano) were decorated on the PANI nanotube successfully via auto-reduction of HAuCl₄ on the PANI nanotube. The morphology of the nanotubes was characterized by means of scanning electron microscopy(SEM) and transmittance electron microscopy(TEM). By varying precursor concentration and incubation time, Au_nano-PANI with different size of Au_nano was obtained conveniently. Glassy carbon electrode modified with the Au_nano decorated PANI nanotubes (Au_nano-PANI/GCE) was prepared and used seccessfully for the catalytic oxidation of ascorbic acid(AA). The results of differential pulse voltammetry indicate that there is a good linear relationship between the peak currents and the concentrations of AA in the range of 5-3000 μmol/L, with the limit of detection of 1 μmol/L(S/N>3). There is no mutual interference between AA and dopamine. The electrode has been successfully applied in the detection of AA in vitamin C tablet sample.     

Polyaniline based nucleic acid sensor

Twenty-bases long NH2-modified DNA and PNA probes specific to a pathogen (Mycobacterium tuberculosis) were covalently immobilized onto a polyaniline (PANI)/Au electrode to detect nucleic acid hybridization with complementary, one-base mismatch and noncomplementary targets within 30 s using Methylene Blue. The PNA-PANI/Au electrode exhibits improved specificity (1000 times) and detection limit (0.125 x 10(-18) M) as compared to that of the DNA-PANI/Au electrode (2.5 x 10(-18) M). These PNA-PANI/Au electrodes can be utilized for detection of hybridization with the complementary sequence in 5 min sonicated M. tuberculosis genomic DNA within 1 min of hybridization time. These DNA-PANI/Au and PNA-PANI/Au electrodes can be used 6-7 and 13-15 times, respectively.     

Synthesis and Electrochemical Investigation of Tetra Amino Cobalt (II) Phthalocyanine Functionalized Polyaniline Nanofiber for the Selective Detection of Dopamine

A new electrochemical sensing platform based on tetra‐amino cobalt (II) phthalocyanine (TACoPc) ingrained polyaniline (PANI) nanofiber composite (TACoPc/PANI hybrid) has been developed for the selective detection of dopamine. The uniform fibrous network of PANI/TACoPc hybrid was synthesized by a one‐step oxidative polymerization at room temperature. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FESEM), energy dispersive X‐ray (EDX), fourier transmission infrared spectroscopy (FTIR), raman spectroscopy, X‐ray diffraction (XRD) and UV‐Visible spectroscopy. The electrochemical behavior of the TACoPc/PANI hybrid material was studied by using different electrochemical techniques, including cyclic voltammetry (CV) and chronoamperometry in 0.1 M phosphate buffer solution (PBS) of pH 7 by modifying the glassy carbon electrode (GCE). Due to the synergistic impact of PANI and TACoPc, the suggested altered electrode provided superior catalytic performance for dopamine even in the presence of ascorbic acid. It exhibited a linear reaction with a high sensitivity of 1.212 μA/μM cm^?2 and a low detection limit of 0.064 μM over the 20–200 μM concentration range in 0.1 M PBS. One of the commonly faced problems of interference of ascorbic acid and uric acid in the electrochemical detection of dopamine was completely excluded from this modified electrode which led to an increase in the catalytic activity of the material for the detection of dopamine in the presence of ascorbic acid.     

Laccase-based amperometric biosensor enhanced by Ni/Au/PPy-COOH multisegmental nanowires for selective dopamine detection

One-dimensional Ni/Au/PPy-COOH nanowires with multiple segments were synthesized in this study. Smooth surfaces and magnetic properties of nanowires were investigated by scanning transmission electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), and Electron Spin Resonance (ESR) techniques. The nanowires were used to modify the screen-printed electrode surface and as a micro-environment for Trametes versicolor laccase. The ability of this enzyme biosensor to detect dopamine change in human biological samples was demonstrated by a wide linear range (0.01–50 μM) and a low LOD (2.265 nM). In addition, the biosensor exhibited excellent selectivity allowing the detection of dopamine in the presence of ascorbic acid, uric acid, L-Cys, serotonin, and glucose, with high sensitivity of reduction currents obtained at −0.2 V (vs. Ag/AgCl). The proposed biosensor allowed the detection of dopamine in commercial serum and artificial urine with recovery values close to 100 %. It also demonstrated reproducibility, reusability, and long-term storage stability. The sensitivity, K_m^app, and I_max values of the biosensor were determined as 2.05 μM and 1.03 μA, respectively. The LAC-Ni/Au/PPy-COOH/NAF/SPE biosensor is a reliable design for detecting dopamine with a wide linear range.     

Plant tissue-based membrane biosensor for l-ascorbic acid

Coupling of a slice of the mesocarp of squash (Cucurbita pepo) or cucumber (Cucumis sativus) to a Clark-type oxygen electrode allows 0.02–0.57 mmol l^?1l-ascorbic acid to be determined amperometrically. The method is based on monitoring the decrease in the curretn of oxygen at an applied potential of ?650 mV vs. Ag/AgCl; oxygen is consumed in the analyte oxidation catalyzed by ascorbate oxidase in the plant tissue. One tissue slice serves for 50–80 measurements at 30°C and pH 6. Spare slices can be stored for at least a year in aqueous 50% glycerol without substantial loss of enzyme activity. The biosensor is highly selective towards ascorbic acid with a response time of 70–90 s, the relative standard deviation being about 3%. Satisfactory results were obtained in the analysis of some fruit juices and vitamin tablets.     

Potential of Gelatin‐Zinc Oxide Nanocomposite as Ascorbic Acid Sensor

We report on the studies relating to fabrication of gelatin B (GB) and zinc oxide (ZnO) based nanocomposite (GB‐ZnO) film deposited on indium‐tin‐oxide (ITO) glass plate, and used for the immobilization of ascorbate oxidase (AsOx) which was further used for ascorbic acid (AA) detection. The structural and morphological studies of GB‐ZnO, and AsOx/GB‐ZnO/ITO bioelectrodes were carried out using XRD, SEM and FTIR techniques. This bioelectrode showed a broad range of linearity (5–500 mg/dL), low detection limit (1 mg/dL), higher sensitivity (0.106 µA mg/dLcm^?2) and low value of the apparent Michaelis? Menten constant (K_m^app=0.35 mg/dL) for AA. Efforts are being made to utilize this electrode for sensing AA in real samples in a bid to develop a strip based sensor.     

PDMS-based gold electrode for sensing ascorbic acid

Electrode with optical shapes is appreciated in microfluidics. In this article, we reported a flexible poly(dimethylsiloxane) (PDMS)-based gold electrode for ascorbic acid detection. Gold nanoparticles were chemically deposited on PDMS and the composite film was applied as working electrode. The electrode could undergo deformation and display good response performance without damage. This biosensor could give quick response to ascorbic acid (AA) (<5s) and the currents were linear with concentrations of AA in range of 0.023-7.00 mM and 30-100 mM, respectively. Limit of detection was 0.008 mM (S/N=3). This biosensor has been applied to determine ascorbic acid content in vitamin C tablets and the results were consistent with traditional iodometric method.     

Towards the development of an integrated capillary electrophoresis optical biosensor

Extending the previous preliminary study on the construction of a capillary electrophoresis (CE)/sensor for the detection of reducing analytes, we focus the interest on the simultaneous detection of redox active species, which are important indicators of the oxidative damage in tissues, of food preservation, and of pollution. The CE/sensor was built by modifying the detector-portion of the capillary with the redox-sensitive polymer polyaniline (PANI). The analyte is detected by monitoring the changes in optical absorption of the PANI film. The CE/sensor was tested, with good results, with ascorbic acid, glutathione (GSH), as well as with compounds with very close similarity (ascorbic and isoascorbic acid). The kinetics of oxidation and reduction of PANI were evaluated. Further a PANI/CE-biological sensor was developed by coupling an enzyme, glucose oxidase (GOD), to the PANI-modified portion of the capillary. The stability of the immobilized GOD and the sensitivity of the CE/biosensor were studied, by using glucose as test analyte in concentrations within the physiological range. The results indicate that the CE/biosensor had good stability (more than 75% of original activity retained after 30 operational days), manufacturing reproducibility and a sensing range convenient for monitoring physiological glucose (1-24 mM).     

A selective dopamine biosensor based on AgCl@polyaniline core-shell nanocomposites

Silver chloride@polyaniline (PANI) core-shell (AgCl@PANI) nanocomposites were synthesized in the presence of polyvinylpyrrolidone (PVP). The obtained AgCl@PANI nanocomposites could be easily dispersed in aqueous media, which overcame the processible issues of PANI. Moreover, the nanocomposites showed excellent electrochemical behavior at pH neutral environment, and had inhibitive effect on oxidation of ascorbic acid. Fourier transform infrared spectrophotometry (FTIR) confirmed the existence of PVP in the nanocomposites. The C=O group of PVP is easy to form hydrogen bonding with the hydroxyl group of ascorbic acid, which can prevent ascorbic acid from oxidization. A selective dopamine biosensor was constructed based on the particular characteristic of the AgCl@PANI nanocomposites by the simple drop-coating. The biosensor could detect dopamine at its very low concentration in the presence of 5000 time concentration of ascorbic acid at neutral environment.