单分散中空介孔结构的盐模板合成及形貌调控

中空介孔结构因具有丰富的内部空间以及多孔渗透性外壳等优势,在催化、能源储存与转化及生物医药等领域得到了广泛应用.然而,目前仍然缺少高效、简便且绿色的合成中空介孔结构的方法.本文以柠檬酸钠胶体颗粒作为模板,通过十六烷基三甲基溴化氨(Cetyltrimethylammonium bromide, CTAB)胶束与正硅酸四乙酯(Tetraethyl orthosilicate, TEOS)的水解低聚物在胶体颗粒表面进行界面共组装,直接生长介孔二氧化硅壳层;然后通过简便的醇洗和水洗分别除去CTAB胶束和柠檬酸钠胶体颗粒后,得到中空介孔结构.进一步研究表明,负电荷的柠檬酸钠胶体颗粒与CTAB胶束之间的静电相互作用是诱导氧化硅低聚物在颗粒表面进行交联组装的关键.基于此,通过控制生长时间实现了对中空介孔结构形貌和壳层厚度的精确调控.所得中空介孔二氧化硅纳米球可以显著增强物质的扩散传输,是理想的催化剂载体,负载金纳米颗粒后可以高效催化4-硝基苯酚的还原反应.研究结果为中空介孔材料的绿色简便合成提供了思路.     

正戊醇对CTAB/KBr胶束体系流变性的影响

报道了正戊醇对CTAB/KBr胶束体系流变性的影响。结果表明：在0.01mol.dm^-^3CTAB(十六烷基三甲基溴化铵)溶液中,正戊醇促使CTAB/KBr胶束体系的粘度增大至一最大值,然后降低在0.08mol.dm^-^3CTAB/KBr的溶液中,正戊醇能促使该胶束体系呈现粘弹性。根据动态荧光法测定的胶束聚集对以上结果进行了解释。     

多级孔Ni/SAPO-5萘加氢制十氢萘催化剂

以CTAB为改性剂,制备了多级孔SAPO-5-x(x为CTAB与SiO_2的摩尔比,x=0.04~0.10)分子筛和多级孔Ni/SAPO-5-x萘加氢制十氢萘催化剂.加入CTAB后形成了微-介孔多级孔孔道结构,孔容和平均孔径均有增加,但是分子筛的晶相结构没有破坏,层状的外貌没有变化.随x值的增大,SAPO-5-x(x=0~0.10)的孔容和平均孔径先增加后减小,SAPO-5-0.07的最大,Ni/SAPO-5-0.07的平均孔径进一步增大;Ni/SAPO-5-x(x=0~0.10)的强酸位强度先下降后增加,x=0.07时强酸位强度最弱,且以L酸中心为主;催化剂的十氢萘选择性先增大后减小,x=0.07时最大.引入CTAB后催化剂活性略有增加,萘转化率接近100%,十氢萘的选择性可以达到95%以上.     

孔径可调的介孔SiO2自支持薄膜的溶剂挥发诱导自组装合成与表征

以十六烷基三甲基溴化铵(CTAB)为模板剂, 正硅酸乙酯为硅源, 在弱酸性条件下利用溶剂挥发诱导自组装(EISA)合成出具有介孔结构的二氧化硅薄膜. 通过控制EISA过程中溶剂挥发的环境, 可在1.4~3.1 nm的范围内调节介孔结构的孔径. 实验表明, 较快的溶剂挥发速率有助于较大孔径的介孔结构生成. 用该方法合成的介孔薄膜具有蠕虫状孔道结构和良好的孔径均一性. 在外观上, 该薄膜具有均匀、透明和无缺陷等特点, 可以自支撑, 并且具有一定的韧性.     

双模板法制备介孔二氧化硅纳米蚕茧

用十八烷基三甲基溴化铵(STAB)作模板剂,左旋香茅醇(CN)为结构助剂,利用溶胶-凝胶法,在CN/STAB摩尔比1∶1条件下制备了介孔二氧化硅纳米蚕茧;采用扫描电镜和透射电镜分析了产物的结构,并对其进行了氮气吸附-脱附测试.结果表明,所制备的介孔二氧化硅纳米蚕茧的孔道与蚕茧表面平行;搅拌速度对介孔二氧化硅纳米蚕茧的长度有较大的影响,随着搅拌速度的增加,其长度减小.     

嵌段共聚物与阳离子表面活性剂混合模板合成介孔SiO_2

利用三嵌段共聚物EO_(20)PO_(70)EO_(20)与阳离子表面活性剂CTAB作为混合 模板合成了内部孔结构与外观形貌同时受到调控的介孔氧化硅。与使用单一共聚物 模板制备的介孔氧化硅相比，在混合模板作用下得到的介孔氧化硅的孔结构有序度 降低，而孔径则随混合模板中共聚物的质量分数的降低而减小。在EO_(20)PO_(70) EO_(20)与CTAB质量比为1:1时可得到形貌完好、表面光滑的介孔氧化硅微米球，其 平均孔径为3.2nm，比表面积为972m~2/g。     

以EDTANa2为矿化剂近中性条件下室温合成介孔二氧化硅

利用EDTANa2作为矿化剂, 在近中性条件下于室温合成了厚壁(约3 nm)蠕虫介孔分子筛. 在反应物配比为n(CTAB):n(TEOS):n(EDTANa2):n(H2O)=(0.05~0.2):(0.1~2):(0.1~0.5):(100~500)范围内都能得到介孔二氧化硅. 以XRD、N2吸附、FTIR、SEM和TEM详细考察了体系配比和温度对介孔二氧化硅结构和形貌的影响, 发现CTAB用量越大, 介孔d值相应增大. 温度对介孔二氧化硅的结构和形貌有很大的影响, 温度在2~15 ℃范围内都能生成孔径分布较规则的介孔, 介孔材料的形貌随温度的升高由空心管变成小颗粒聚集体; 合成的介孔分子筛中的模板剂可以通过乙醇萃取的方式除去. 提出了介孔的生成遵从(S+-E-)0-I0中性模板机理.     

以阴离子表面活性剂/阳离子聚铵复合胶束为模板合成有序介孔二氧化硅

基于静电作用, 阴离子表面活性剂可与阳离子聚铵组装形成复合胶束. 借助阳离子聚铵,复合胶束可以作为模板与硅源协同组装, 形成高度有序的介孔二氧化硅. 本文通过调变不同种类阴离子表面活性剂、合成体系pH值、合成温度及阳离子聚铵和硅源用量等因素, 合成了具有不同介观结构和形貌的介孔二氧化硅. 实验证实阴离子表面活性剂/阳离子聚铵复合胶束模板法是合成介孔二氧化硅的一种通用方法.     

水和辛胺对ZnO多孔纳米块体孔道结构的影响

以ZnO纳米颗粒为原料, 分别用水和辛胺水溶液作为造孔剂, 利用溶剂热压方法制备了ZnO多孔纳米块体. 实验结果表明, 当以水作造孔剂时, 随着ZnO纳米粉/水(质量比)比值的减小, ZnO多孔纳米块体的孔径分布变宽, 比表面积和孔隙率增加; 加入辛胺后, ZnO多孔纳米块体的孔径分布变窄, 但比表面积和孔隙率略有减少. 随着辛胺用量的增加, 比表面积和孔隙率又同时呈上升趋势. 对ZnO多孔纳米块体进行的红外吸收测试结果表明, 在制备多孔纳米块体过程中, 水及辛胺基本上都从样品中逸出, 孔道中只有微量残留.     

微乳液法合成沸石/介孔二氧化硅复合微球

利用简单微乳液自组装体系, 制备了介孔二氧化硅与Y型或Ti-MWW沸石晶体复合形成的沸石/介孔二氧化硅微球(ZMMS). 硅源正硅酸四丁酯与阳离子型季铵盐表面活性剂形成稳定的O/W微乳液形成大颗粒, 沸石颗粒由于疏水作用而进入油相, 同时, 季铵盐表面活性剂和正硅酸四丁酯组装形成介孔材料. 优化合成条件可以有效控制复合微球的沸石/介孔二氧化硅质量比(0～2.3)和直径(186～965 μm). 两种沸石/介孔二氧化硅复合微球材料的介孔孔径分别为3.98 nm(Y型沸石)和3.75 nm (Ti-MWW型沸石). Ti-MWW沸石/介孔二氧化硅复合微球在液相催化环氧化反应中表现出良好的机械强度, 并且能够达到与Ti-MWW沸石原粉相当的催化活性.     

Synthesis of rod-like mesoporous silica with hexagonal appearance using sodium silicate as precursor

Using sodium silicate as precursor, rod-like mesoporous silica with hexagonal appearance was synthesized by controlling the pH value of a mixed micelles solution of cetyltrimethylammonium bromide (CTAB) and cetyltrimethylammonium chloride (CTAC) during hydrolysis of ethyl acetate. The resulting mesoporous silica was characterized by small angle X-ray diffraction, nitrogen gas adsorption-desorption measurement and scanning electron microscopy. Results showed that the regular rod-like shapes with hexagonal appearance were obtained at a 9:1 molar ratio of CTAB to CTAC, and that the amounts and lengths of the rod-like mesoporous silica particles decreased with decreasing CTAB to CTAC molar ratio. There existed a type IV adsorption isotherm and an H1 hysteresis loop in N₂ gas adsorption-desorption curves.     

Synthesis of hollow spherical silica with MCM-41 mesoporous structure

Hollow spherical mesoporous silica was synthesized by using sodium silicate as a precursor and a low concentration of cetyltrimethylammonium bromide (CTAB) (0.154 mol dm^–3). The resulting hollow spherical particles were characterized with scanning electron microcopy (SEM), small-angle X-ray diffraction (SXRD), transmission electron microscopy (TEM), and N₂ gas adsorption and desorption techniques. The results showed that regular spherical mesoporous silica could be obtained only if the molar ratio of propanol to CTAB was in the range of approximately 8:1–9:1. The spherical particles were hollow (inside), and the shell consisted of smaller particles with a pore structure of hexagonal symmetry. With an increase of the molar ratio of propanol to CTAB, the distance (a value) between centers of two adjacent pores increased, and the pore structure of mesoporous silica became less ordered. N₂ adsorption–desorption curves revealed type IV isotherms and H1 hysteresis loops; with an increase of the molar ratio of propanol to CTAB, the pore size with Barrett–Joyner–Halenda (BJH) diameter of the most probable distribution decreased, but the half peak width of the pore size distribution peak increased     

以混合表面活性剂为模板可控合成MCM-48和MCM-41分子筛

利用阳离子和三嵌段共聚物混合表面活性剂为模板,在水热条件、碱性介质中可控合成出MCM-48和MCM-41分子筛。在固定P123(聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物):TEOS(正硅酸乙酯)(物质的量的比)为0.01875的体系中,调节CTAB(十六烷基三甲基溴化铵)∶TEOS(正硅酸乙酯)物质的量比值m,当m在0.12~0.13范围合成出MCM-48分子筛;当m在0.04~0.08范围合成出MCM-41分子筛。通过XRD,TEM,N2物理吸附,IR等方法进行了表征。结果表明:聚氧乙烯-聚氧丙烯-聚氧乙烯三嵌段共聚物(P123)的加入可以更大程度地降低合成介孔材料所需阳离子表面活性剂的用量;可控合成的介孔材料具有高比表面积、高度有序的孔道结构、较集中的孔径分布。     

Study of the Pm3n space group of cubic mesoporous silica.

By using a Gemini surfactant, [C14H25N+(CH3)2-(CH2)2-N+(CH3)2C14H25]2 Br-(C(14-2-14)), with a short spacer group (s = 2) as structure-directing agent and sodium silicate as precursor, high-quality, ordered cubic mesoporous silica with space group Pm3n was prepared by the S+I-route (S = surfactants, I = precursor). The samples were characterized by small-angle X-ray diffraction, transmission electron microscopy, and N2 adsorption-desorption. The results showed that the pore structure of the resulting mesoporous silica belonged to the cubic system (space group Pm3n). The unit-cell parameter of the cubic system was in the range of 8.81-9.14 nm. The high-quality cubic mesoporous structure was formed at molar ratios of C(14-2-14) to sodium silicate of 0.33:1 to 0.16:1 and a molar ratio of ethyl acetate to sodium silicate of 2:1. N2 adsorption-desorption curves revealed type IV isotherms and H1 hysteresis loops. The primary pore volume, and the most probable pore size according to the Barrett-Joyner-Halenda (BJH) model, increased with increasing molar ratio of C(14-2-14) to sodium silicate.     

Structural Control of Mesoporous 1,4-Phenylene-silica Using the Mixture of CTAB/SDS

The morphology, pore architecture and crystallinity of the mesoporous 1,4‐phenylene‐silicas were controlled using the mixtures of cetyltrimethylammonium bromide (CTAB) and sodium dodecylsulfate (SDS). When the SDS/CTAB molar ratio increased from 0 to 1.0, the morphology of the mesoporous 1,4‐phenylene‐silicas changed in a sequence of sphere, hexagonal short rod, worm‐like, bent flake and flower‐like structure; the pore architecture of them changed from a hexagonal arranged tubular structure to a lamellar one; and the organization of the smallest repeat units within the wall changed from a random structure to a crystalline structure. At the SDS/CTAB molar ratios of 0.3 and 0.5, 1,4‐phenylene‐silica nanofibers with lamellar mesopores outside and tubular pore channels inside were obtained. The lamellar mesopores should be formed by merging the rod‐like micelles during the reaction process.     

阳离子与非离子混合表面活性剂模板合成介孔SiO2

利用各种两亲分子有序组合体构成超分子模板,合成从介观到宏观尺度不同形态的无机材料成为材料科学新崛起的研究方向[1].介孔SiO2在催化、吸附、分离介质及化学传感器等方面有广阔的应用前景.     

Coexistence of two kinds of fluorinated hydrogenated micelles as building blocks for the design of bimodal mesoporous silica with two ordered mesopore networks

A simple and effective route has been developed for the synthesis of bimodal (3.6 and 9.4 nm) mesoporous silica materials that have two ordered interconnected pore networks. Mesostructures have been prepared through the self-assembly mechanism by using a mixture of polyoxyethylene fluoroalkyl ether and triblock copolymer as building blocks. The investigation of the R(F)(8)(EO)(9)/P123/water phase diagram shows that in the considered surfactant range of concentrations the system is micellar (L(1)). DLS measurements indicate that this micellar phase is composed of two types of micelles; the size of the first one at around 7.6 nm corresponds unambiguously to the pure fluorinated micelles. The second type of micelles at higher diameter consists of fluorinated micelles that have accommodated a weak fraction of P123 molecules. Thus, in this study the bimodal mesoporous silica is really templated by two kinds of micelles.     

Facile fabrication of hollow mesoporous silica nanospheres for superhydrophilic and visible/near-IR antireflection coatings

A series of hierarchically mesostructured silica nanoparticles (MSNs) less than 100 nm in size were fabricated by means of a one-step synthesis using dodecanethiol (C(12)-SH) and cetyltrimethylammonium bromide (CTAB) as the dual template, and trimethylbenzene (TMB) as the swelling agent. Silica nanoparticles with varied morphologies and structures, including mesoporous silica nanoparticles with tunable pore size, mesoporous silica nanoparticles with a thin solid shell, hollow mesoporous silica nanoparticles with tunable cavity size, and hollow mesoporous silica nanoparticles with a thin solid shell, were obtained by regulating the TMB/CTAB molar ratio and the stirring rate with the assistance of C(12)-SH. Silica particulate coatings were successfully fabricated by using MSNs with varied morphologies and structures as building block through layer-by-layer dip-coating on glass substrates. The thickness and roughness of the silica particulate coatings could be tailored by regulating the deposition cycles of nanoparticles. The silica particulate coatings composed of hollow mesoporous silica nanoparticles with a thin shell (S2) increased the maximum transmittance of slide glass from 90 to 96%, whereas they reduced its minimum reflection from 8 to 2% at the optimized wavelength region that could be adjusted from visible to near-IR with a growing number of deposition cycles. The coatings also exhibited excellent superhydrophilic and antifogging properties. These mesostructured silica nanoparticles are also expected to serve as ideal scaffolds for biological, medical, and catalytic applications.     

Mixed micellar phases of nonmiscible surfactants: mesoporous silica with bimodal pore size distribution via the nanocasting process

Highly organized mesoporous silica monoliths were reproducibly prepared by nanocasting mixtures of fluorinated nonionic surfactants and micelles of two hydrocarbon block copolymers. It is the special feature of this fluorocarbon/hydrocarbon template mixture that they form not mixed micelles but individual micelles instead. By careful analysis of the pore architectures by gas sorption measurements and transmission electron microscopy in dependence on the relative template concentration, two different situations could be identified: (a) mesoscopically demixed samples and (b) mixed micellar phases where the two different micelles are packed in some type of organized alloy phase. Besides identification of such mixed phases for the first time for fluorocarbon/hydrocarbon mixtures, the resulting porous systems with controlled bimodal pore size distribution might be interesting from a materials perspective.