等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

La_(0.67)Sr_(0.33)Fe_xMn_(1-x)O_3制备和奇特磁电阻效应

系列陶瓷氧化物La0.67Sr0.33FexMn1-xO3（0.055x0.33）通过共沉淀法工艺合成获得.经X射线衍射分析表明，所得氧化物均为单相，属三方结构.在零场和外加磁场下的四极法电阻测试结果表明：所有样品都具有较大的磁电阻效应，当x<0.13时，样品的电阻率-温度曲线中均出现电阻率峰（电阻率出现从半导体性向金属性的转变），该电阻率峰处的温度（Tp）随x的增大而向低温区移动，磁电阻效应是负值;x＝0.23时，样品已呈半导体性，磁电阻效应仍是负值;然而x＝0.33时，样品虽也表现为半导体性，但其中的磁电阻效应出现奇特的正负交替转换.     

Improvement on Electrical Properties and Magnetoresistance Induced by Pd or Ag Addition in La0.67(Ca0.65Ba0.35)0.33MnO3 Manganites

Electrical properties and magnetoresistance have been studied in two series of xAg-La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃ and xPd-La_0.67(Ca_0.65Ba_0.35)_0.33MnO₃ (abbreviated by xAg-LCBMO and xPd-LCBMO) composites. Both Pd and Ag addition induce a decrease in resistivity and an increase in temperature at which the resistivity reaches its maximum. This is mainly due to the improvement of grain boundaries caused by the segregation of good conductive metal grains on the grain boundaries/surfaces. In addition, both Pd and Ag addition induce a large enhancement of room temperature magnetoresistance (RTMR). Note that 27% molar ratio of Ag addition induces a large RTMR of about 70%, about ten times larger than pure LCBMO, whereas 27% molar ratio Pd addition brings a much larger RTMR of about 170%. The large enhancements of MR can be attributed to the decrease in resistivity of the samples caused by the good conductive metal. On the other hand, the polarization of Pd atoms near the Mn ions on the grain surfaces/boundaries plays a very im-portant role in the increase in MR, which induces a large number of spin clusters in Pd-added samples.     

混合掺杂和非计量比对钕锶锰氧体系的影响

通过对Sr、Ba混合掺杂体系（x＝0．27、0．165、0．06）和非计量体系Nd0.67SrxBaxMnOz（x＝0．27．0．06）,导电性能的研究发现：混合二价离子掺杂体系Nd0.67SrxBa0.33-xMnO3与单一二价离子掺杂体系（Nd0.67Sr0.33MnO3和Nd0．67Ba0.33MnO3）具有不同的导电机制,非计量比使Nd0.67SrxBaxMnOz体系出现晶格收缩,电阻率随温度的降低出现半导体－金属转变,与此同时体系的电阻率减小,另外还发现,Mn离子的非计量与A位离子的相比对体系晶格收缩和导电性能的影响都更为显著。     

1100 ℃合成La2/3Ca1/3Mn1-xCuxO3低场庞磁电阻效应

采用溶胶-凝胶法制备了La2/3Ca1/3Mn1-xCuxO3系列样品.实验研究了系列样品的电输运性质、高温导电机制和低场磁电阻效应.结果发现样品高温下导电遵从Mott变程跳跃机制;在0.3 T的磁场下,绝缘体-金属转变附近磁电阻(MR0=[R(H=0)-R(H)]/R(H=0))由没有掺杂时的2%增加到4%Cu掺杂时的80%;实验同时发现与颗粒晶界有关的磁电阻也有实质性的提高.实验结果表明少量的Cu掺杂可以大大提高低场磁电阻效应.     

Li+,Eu3+共掺杂La2MoO6红色荧光粉的Pechini法合成及近紫外/蓝光激发下的发光特征

采用Pechini法合成了白光LED用红色荧光粉La_1.9-xMoO₆:0.10Eu³⁺,xLi⁺(x=0,0.10,0.20,0.25),并对样品分别进行了X射线衍射(XRD)、扫描电子显微镜(SEM)、电子能谱(EDX)以及荧光光谱(PL)等技术手段分析。 PL光谱显示该荧光粉可被近紫外光(395 nm)和蓝光(466 nm)有效激发,产生616和623 nm强的红光发射,归属于Eu³⁺的⁵D₀→⁷F₂电偶极跃迁。该荧光粉与近紫外LED芯片(370~410 nm)和蓝光LED芯片(450~470 nm)均匹配良好,具有潜在的商业应用价值。 共掺Li⁺离子作为敏化剂能显著提高荧光粉的发光强度,且最优掺杂量为x=0.20。     

Switch-on fluorescence sensor for ascorbic acid detection based on MoS2 quantum dots-MnO2 nanosheets system and its application in fruit samples

In this work,molybdenum disulfide quantum dots(MoS_2 QDs) were firstly prepared by hydrothermal method using sodium molybdate and glutathione as precursors,and applied in ascorbic acid detection.When joining MnO_2 nanosheets into MoS_2 QDs solution,they produced an obvious fluorescence quenching,which should be due to inner filter effect(IFE).Meanwhile,the fluorescent probe was formed,Interestingly,we found that this quenching phenomenon disappeared with the addition of ascorbic acid,In other words,the fluorescence gradually restored.This recovery phenomenon is mainly due to the reduction effect of ascorbic acid for MnO_2 nanosheets.Under the optimum conditions,the limit of detection(LOD) of 39 nmol/L for ascorbic acid was achieved with a linear range of 0.33-5.00 μmol/L.The repeatability was better than 5.0% for ascorbic acid in both standard and fruit samples(n = 3).Moreover,the as-fabricated fluorescent sensing system was successfully employed to detect the ascorbic acid levels in hawthorn and jujube with satisfactory results.     

(1-x)La_(0.67)Ca_(0.33)MnO_3/xCuO复合体系与La_(0.67)Ca_(0.33)Mn_(1-x)Cu_xO_3电输运行为比较

用不同实验方法制备了名义组分为(1-x)La_(0.67)Ca_(0.33)MnO_3/xCuO(LCMO/CuO)和La_(0.67)Ca_(0.33)Mn_(1-x)Cu_xO_3(LCMCO)两组样品,在宽的温度范围内研究了样品的电输运行为随Cu含量x的变化关系,发现这两组样品表现出不同的行为.对于LCMCO,随x的增加,金属-绝缘体转变温度T_p迅速降低,当x=5.5%,样品表现出绝缘体导电行为;而LCMO/CuO复合样品,当x≤6%时,随x增加,Tp逐渐下降,x≥6%时,T_p不再继续降低,所有样品几乎表现出相同的电输运行为.另外,这两组样品均表现出较好的低场磁电阻效应(LFMR),在0.3 T下样品的最大磁电阻分别达到了～76%和88%.基于样品结构以及制备过程的分析,我们认为LFMR效应的增强主要是因为颗粒边界上形成的Cu相关自旋无序层引起的.     

Ag+存在下催化还原铬黑T及应用于Ag+检测

以铬黑T(EBT)为探针,在有Ag⁺存在的最优条件下,EBT被NaBH 4催化还原,体系在445 nm发射波长处荧光强度明显增强,基于此构建一种光学测定溶液中微量Ag⁺的方法。在最优条件下,Ag⁺浓度在(7.5×10-9~1.0×10^-6 mol·L^-1)范围内呈良好的线性关系,线性回归方程为ΔI F=5.59×10⁸ c-31(c,mol·L^-1,r=0.9966),Ag⁺的最低有效检测浓度为6.0×10^-8 mol·L^-1。在最优条件下,运用该方法对样品中Ag⁺浓度进行检测,样品中Ag⁺浓度的检测回收率在98.8%~102.4%之间,RSD=2.1%。该检测方法能够对水溶液中微量的Ag⁺进行有效定量检测,且操作简单、检测限低、灵敏度高。     

Ultrasonic Study on Jahn-Teller Distortions in La1=3Sr2=3CoO3

The longitudinal ultrasonic velocity (Vl), attenuation (ffl), magnetization and resistivity of single phase polycrystalline La1=3Sr2=3CoO3 were measured as a function of temperature from 20 K to 300 K. The resistivity shows metallic behavior in the whole temperature range and a kink at 235 K was observed, which coincides with the ferromagnetic transition temperature (Tc). As the temperature cools down from Tc, the Vl softens conspicuously at beginning and reaches a minimum at 120 K. After that the Vl dramatically stiffens below 120 K accompanied by a wide attenuation peak. The analysis of the results suggests that these ultrasonic anomalies may correspond to local lattice distortions via the Jahn-Teller effect of intermediate spin Co3+.     

Ca2.9M0.1Co4O9 (M=Ag,La, Ba)复合氧化物体系的制备及电输运性能

采用柠檬酸溶胶-凝胶结合放电等离子烧结方法制备了p型Ca位掺杂的Ca2.9M0.1Co4O9(M=Ag, La, Ba)复合氧化物块体试样, 对其进行X 射线衍射(XRD)分析, 表明产物为单一物相, Ca位掺杂原子可以改变Ca2.9Co4O9多晶体的取向度, 掺杂试样取向度随着掺杂原子电负性的降低而提高|对其进行扫描电子显微镜(SEM)分析结果表明, 试样呈层状结构, 且层状结构随掺杂原子电负性降低而逐渐明显; 电性能分析结果表明, 测试温度范围内掺杂试样各温度点的电阻率随着掺杂原子电负性的降低而升高, 所有试样的载流子传输层未受影响, 导电机理未发生变化. 其中掺杂电负性最高的Ag原子的烧结体保持最低取向度的同时具有最低的电阻率, 在973 K时达6.87 mΩ·cm, 而掺杂电负性最低的Ba原子的烧结体具有高的取向度的同时具有较高的电阻率, 在973 K时达8.22 mΩ·cm.