Direct determination of toxic trace metals in honey and sugars using inductively coupled plasma atomic emission spectrometry

A rapid method for the determination of Pb, Cd, Cu, Cr, Co, Ni, Mn and Zn in honey and sugars without prior digestion or ashing of the sample was developed, using inductively coupled plasma atomic emission spectrometry (ICP-AES). The critical instrumental parameters such as sample flow rate and radio frequency incident power were thoroughly optimized. The effect of matrix type and its concentration was also examined for glucose/fructose, sucrose and honey matrices. The sensitivity was investigated using calibration curves obtained in presence of the above matrices. The obtained recoveries for Cd, Cu, Cr, Co, Ni and Mn at the μg l⁻¹ level were satisfactory and practically independent of the matrix used for the calibration standards. The recoveries of Pb and Zn were less sufficient. Various commercial samples of honey, sugar, glucose and fructose were analyzed with respect to their toxic metal content. The method can be applied for routine analysis, quality and environmental pollution control purposes at the μg l⁻¹ level of concentration, after suitable dilution of the samples.     

Multielemental Analysis of Human Serum by Dynamic Reaction Cell–Inductively Coupled Plasma Mass Spectrometry

The selection of the most suitable dilution methods for determination of trace elements in human serum using inductively coupled plasma mass spectrometry is reported. The trace elements were Al, V, Cr, Fe, Mn, Co, Cu, Zn, As, Cd, Sn, Tl, and Pb. The performance of various dilution methods was assessed by precision, linearity, detection limits, quantification limits, fortified recoveries, and the analysis of reference materials. The results demonstrate that diluted solution containing only nitric acid is most suitable for As, Cr, Mn, and Co in serum. Dilute solutions containing nitric acid and Triton X-100 were most appropriate for Cu, Zn, Cd, and Tl. The optimum conditions for Al, V, Mn, Fe, Cr, Co, Sn, and Pb used tetra-n-butylammonium hydroxide, Triton X-100, and ethylenediamine tetraacetic acid.     

Trace Elements in Pleurotus Ostreatus,P. Eryngii,and P. Nebrodensis Mushrooms Cultivated on Various Agricultural By-Products

Abstract

Mushrooms are efficient accumulators of essential and toxic elements. Although oyster (Pleurotus spp.) mushrooms are widely commercialized and consumed, few data exist regarding trace elements content and bioaccumulation in cultivated P. ostreatus and P. eryngii, while no data are available for P. nebrodensis. The contents of Al, As, Ba, Cd, Co, Cr, Cs, Cu, Fe, K, Mn, Na, Ni, Pb, Rb, Sr, V, and Zn were monitored using inductively coupled plasma-mass spectrometry (ICP-MS) and atomic emission spectrometry (AES) in P. ostreatus, P. eryngii, and P. nebrodensis mushrooms and their cultivation substrates that include wheat straw (WHS), grape marc (GMC), olive leaves (OLV), and two-phase olive mill wastes (OMW), separately or in mixtures. Bioaccumulation factors (BAFs) less than 0.3 were obtained for Al, Ba, Co, Cr, Fe, Mn, Ni, Pb, Sr, and V; BAFs exceeding 1 for K?>?Zn?>?Cd?>?Cr?>?Rb?>?As, while the BAFs for Na were less 0.7. Mushrooms grown on OLV and OMW presented lower BAFs than those grown on WHS and GMC for all elements except for K, Cd, and Cu. P. ostreatus was an effective accumulator for Cr, Fe, and Zn; P. eryngii for Al, Cs, Ni, and V; and P. nebrodensis for As and Cd. The estimated daily intakes (μg kg^?1 body weight) from mushroom consumption were less than 0.010 for As, Cd, Co, Cs, Pb, and V, 0.010–0.10 for Ba, Cr, Ni, and Sr, 0.10–5.0 for Al, Cu, Fe, Mn, Rb, and Zn, 65–83 for Na, and 858–1030 for K. Overall, the mushrooms studied provide significant amounts of K, adequate amounts of Mn and Zn and low amounts of Na and toxic elements.     

Evaluation of strontium isotope abundance ratios in combination with multi-elemental analysis as a possible tool to study the geographical origin of ciders

In order to evaluate alternative analytical methodologies to study the geographical origin of ciders, both multi-elemental analysis and Sr isotope abundance ratios in combination with multivariate statistical analysis were estimated in 67 samples from England, Switzerland, France and two Spanish regions (Asturias and the Basque Country). A methodology for the precise and accurate determination of the ⁸⁷Sr/⁸⁶Sr isotope abundance ratio in ciders by multicollector inductively coupled plasma mass spectrometry (MC-ICP-MS) was developed. Major elements (Na, K, Ca and Mg) were measured by ICP-AES and minor and trace elements (Li, Be, B, Al, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Y, Mo, Cd, Sn, Sb, Cs, Ba, La, Ce, W, Tl, Pb, Bi, Th and U) were measured by ICP-MS using a collision cell instrument operated in multitune mode. An analysis of variance (ANOVA test) indicated that group means for B, Cr, Fe, Ni, Cu, Se, Cd, Cs, Ce, W, Pb, Bi and U did not show any significant differences at the 95% confidence level, so these elements were rejected for further statistical analysis. Another group of elements (Li, Be, Sc, Co, Ga, Y, Sn, Sb, La, Tl, Th) was removed from the data set because concentrations were close to the limits of detection for many samples. Therefore, the remaining elements (Na, Mg, Al, K, Ca, Ti, V, Mn, Zn, As, Rb, Sr, Mo, Ba) together with ⁸⁷Sr/⁸⁶Sr isotope abundance ratio were considered for principal component analysis (PCA) and linear discriminant analysis (LDA). Finally, LDA was able to classify correctly 100% of cider samples coming from different Spanish regions, France, England and Switzerland when considering Na, Mg, Al, K, Ca, Ti, V, Mn, Zn, As, Rb, Sr, Mo, Ba and ⁸⁷Sr/⁸⁶Sr isotope abundance ratio as original variables.     

Use of enzymatic hydrolysis for the multi-element determination in mussel soft tissue by inductively coupled plasma-atomic emission spectrometry

A systematic evaluation of different variables affecting the enzymatic hydrolysis of mussel soft tissue by five enzymes, three proteases (pepsin, pancreatin and trypsin), lipase and amylase, has been carried out for the determination of trace elements (As, Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) by inductively coupled plasma-atomic emission spectrometry (ICP-AES). Enzymatic hydrolysis methods offers advantages such as a less species alteration, safer laboratory conditions and a less contaminant wastes. The enzymatic hydrolysis was performed in an incubation camera Boxcult with orbital and horizontal shaker. Variables affecting the enzymatic hydrolysis process were simultaneously studied by applying a Plackett-Burman design (PBD). For a confidence interval of 95%, the significant factors for all enzymes and for most of the elements were the pH, the incubation temperature and the ionic strength. These significant factors were optimized later by using a central composite design (CCD), which gave optimum conditions at pH of 1, incubation temperature of 37 °C and ionic strength fixed by sodium chloride at 0.2 M when using pepsin. For pancreatin, trypsin, lipase and amylase there were found two different optimum condition sets. The first one involves the use of a 0.5 M phosphate buffer (ionic strength), at a pH of 6 and at an incubation temperature of 37 °C, which allows the quantitative extraction of Al, Cr, Mn, Pb and Zn. The second conditions set employees a 0.1 M phosphate buffer (ionic strength), a pH of 9 and an incubation temperature at 37 °C, and it results adequate to extract As, Cd, Cu, Fe and Ni. Analytical performances, repeatability of the over-all procedure and accuracy, by analyzing DORM-1, DORM-2 and TORT-1 certified reference materials, were finally assessed for each enzyme. Good agreement with certified values has been assessed for most of the elements (As, Cd, Cr, Cu, Mn, Ni, Pb and Zn) when using trypsin, pepsin and/or pancreatin, except for Cd and Pb in DORM-1 and DORM-2 because of the certified contents in such certified reference materials are lower than the limit of detection (0.10 and 0.16 μg g⁻¹ for Cd and Pb, respectively, for the use of trypsin).     

A pilot study on the feasibility of the preparation of a new certified reference material based on the Antarctic Scallop Adamussium Colbecki

As foreseen by the Italian National Programme of Research in Antarctica, a preliminary investigation was performed to ascertain the feasibility of the production of a new Certified Reference Material for trace elements based on the bivalve Adamussium colbecki. The scallops sampled in Antarctica during the 1999–2000 Italian scientific expedition were analyzed by inductively coupled plasma atomic emission spectrometry and high-resolution inductively coupled plasma mass spectrometry for their content in selected trace elements (As, Cd, Cr, Cu, Fe, Hg, Mn, Mo, Ni, V and Zn). The certification campaign will be undertaken on the basis of the findings of this feasibility study in close cooperation with the Institute for Reference Materials and Measurements, Joint Research Centre of the European Commission.     

Inductively Coupled Plasma Mass Spectrometry for Sequential Determination of Trace Metals in Rain and River Waters Using Electrothermal Vaporization

Abstract

The sequential determination of 14 trace metals, Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Mo, Cd, Sb and Pb, in rain and river water samples has been investigated using an inductively coupled plasma mass spectrometry (ICP-MS) with a graphite rod electrothermal vaporizer (ETV) in the presence of the mixed modifier of palladium nitrate and magnesium nitrate. The sensitivity enhancements due to the presence of the modifier were observed for all analyte elements. Detection limits as high as 0.52, 0.13, 0.89, 0.35, 1.76, 0.5, 0.9, 0.5, 0.04, 1.03, 0.28, 0.07, 0.1 and 3.78 pg, respectively, for Al, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Mo, Cd, Sb and Pb have been achieved. For the determination of trace metals in both rain and river water samples by this method, the repeatibility of sample solution were very good, i.e. from 1% to 7% (as a coefficient variation) and the recoveries of elements were good enough, i.e. from 81% to 106%, by using a standard addition method. There was no difference between the results obtained by nebulizer ICP-MS and those obtained by this method, except for zinc and arsenic.     

An off-line automated preconcentration system with ethylenediaminetriacetate chelating resin for the determination of trace metals in seawater by high-resolution inductively coupled plasma mass spectrometry

A novel automated off-line preconcentration system for trace metals (Al, Mn, Fe, Co, Ni, Cu, Zn, Cd, and Pb) in seawater was developed by improving a commercially available solid-phase extraction system SPE-100 (Hiranuma Sangyo). The utilized chelating resin was NOBIAS Chelate-PA1 (Hitachi High-Technologies) with ethylenediaminetriacetic acid and iminodiacetic acid functional groups. Parts of the 8-way valve made of alumina and zirconia in the original SPE-100 system were replaced with parts made of polychlorotrifluoroethylene in order to reduce contamination of trace metals. The eluent pass was altered for the back flush elution of trace metals. We optimized the cleaning procedures for the chelating resin column and flow lines of the preconcentration system, and developed a preconcentration procedure, which required less labor and led to a superior performance compared to manual preconcentration (Sohrin et al. [5]). The nine trace metals were simultaneously and quantitatively preconcentrated from ∼120 g of seawater, eluted with ∼15 g of 1 M HNO₃, and determined by HR-ICP-MS using the calibration curve method. The single-step preconcentration removed more than 99.998% of Na, K, Mg, Ca, and Sr from seawater. The procedural blanks and detection limits were lower than the lowest concentrations in seawater for Mn, Ni, Cu, and Pb, while they were as low as the lowest concentrations in seawater for Al, Fe, Co, Zn, and Cd. The accuracy and precision of this method were confirmed by the analysis of reference seawater samples (CASS-5, NASS-5, GEOTRACES GS, and GD) and seawater samples for vertical distribution in the western North Pacific Ocean.     

Uptake,Translocation, and Bioaccumulation of Elements in Forest Nettle (Laportea alatipes)

Elements found in the edible parts of plants are considered to be the main source of nutrients for humans and animals. However, there is insufficient information on the relationship between heavy metal pollution in the growing soil of most edible plants. In this study, the distribution of elements in the edible forest nettle (Laportea alatipes) was evaluated as a function of geographical location. Forest land soils had higher concentrations of minor elements (Cu, Cr, Ni, and Zn) compared to soils from rural and suburban areas. Translocation factors for Cd and Pb showed effective translocation from the roots to the leaves; however, these heavy metals in leaves were still above South African maximum permissible levels for vegetables. Atmospheric depositions may play a significant role in higher Cd and Pb concentrations in the leaves. Bioaccumulation factors showed the plant to accumulate Cu, Mn, and Zn to meet physiological requirement levels. Geoaccumulation indices and enrichment factors showed no soil contamination or minimal enrichment by trace metals. Principal component analysis showed Co, Cr, Cu, Fe, Ni, Pb, and Zn in soil to originate from a common source which may be soil silicates and other minerals.     

Investigations on the use of pneumatic cross-flow nebulizers with dual solution loading including the correction of matrix effects in elemental determinations by inductively coupled plasma optical emission spectrometry

The use of a so-called trihedral and a T-shaped cross-flow pneumatic nebulizer with dual solution loading for inductively coupled plasma optical emission spectrometry has been studied. By these devices analyte clouds from two solutions can be mixed during the aerosol generation step. For both nebulizers the correction of matrix effects using internal standardization and standard addition calibration in an on-line way was investigated and compared to elemental determinations using a conventional cross-flow nebulizer and calibration with synthetic standard solutions without matrix matching. A significant improvement of accuracy, both for calibration with internal standardization and standard addition, was obtained in the case of four synthetic solutions containing each 40 mmol L^− 1 Na, K, Rb and Ba as matrix elements and 300 μg L^− 1 Cd, Co, Cr, Cu, Fe, Mn, Ni and Pb as analytes. Calibration by standard addition in the case of dual solution loading has been shown to be very useful in the determination of elements at minor and trace levels in steel and alumina reference materials. The results of analysis for minor concentrations of Cr, Cu and Ni in steel as well as for Ca, Fe, Ga, Li, Mg, Mn, Na, Si and Zn in alumina powder certified reference materials subsequent to sample dissolution were found to be in good agreement with the certificates. Limits of detection were found to be only slightly above those for a conventional cross-flow nebulizer and a precision better than 3% was realized with both novel nebulizers.     

Bioaccessibility of selected trace metals in urban PM<Subscript>2.5</Subscript> and PM<Subscript>10</Subscript> samples: a model study

Bioaccessibility of trace metals originating from urban particulate matter was assessed in a worst case scenario to evaluate the uptake and thus the hazardous potential of these metals via gastric juice. Sampling was performed over a period of about two months at the Getreidemarkt in downtown Vienna. Concentrations of the assayed trace metals (Ti, Cr, Mn, Co, Ni, Cu, Zn, Mo, Ag, Cd, Sn, Sb, Tl and Pb) were determined in PM_2.5 and PM₁₀ samples by ICP-MS. The metal concentrations in sampled air were in the low picogram to high nanogram per cubic metre range. The concentrations in PM_2.5 samples were generally lower than those in PM₁₀ samples. The average daily intake of these metals by inhalation for a healthy adult was estimated to be in the range of <1 ng (Tl) to >1,000 ng (Zn). To estimate the accessibility of the inhaled and subsequently ingested metals (i.e. after lung clearance had taken place) in the size range from 2.5- to 10-μm aerodynamic equivalent diameter, a batch-extraction with synthetic gastric juice was performed. The data were used to calculate the bioaccessibility of the investigated trace metals. Extractable fractions ranged from 2.10% (Ti in PM_2.5) to 91.0% (Cd in PM_2.5), thus yielding bioaccessible fractions (PM_2.5–10) from 0.16 ng (Ag) to 178 ng (Cu).     

Inductively coupled plasma optical emission spectrometric determination of trace element in PM10 airborne particulate matter collected in an industrial area of Argentina

Trace metals of relevance from the environmental and toxicological point of view were quantified in the city of Campana, Buenos Aires, Argentina. The collection of particulate matter was performed on ash-free fiber glass filters using high-volume samplers with a PM₁₀ sampling head, during a 3-month period in 2002. An acid leaching of elements deposited on the filters was adopted paying special attention to the recovery of volatile elements. Analysis was performed by inductively coupled plasma optical emission spectrometry (ICP OES) to ascertain the concentrations of 12 key elements, namely, Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Ti, V and Zn. The validation of the procedure was performed by the analysis of the standard reference material NIST 1648, urban particulate matter, and good agreement between concentrations found and the reported certified values was achieved. Blank filters were spiked with the analytes investigated and the recoveries varied between 83% and 92%. Metal concentrations spanned the range 0.03 ng m⁻³ (equivalent to 0.42 μg g⁻¹) for Cd to 1.9 μg m⁻³ (equivalent to 29.7 mg g⁻¹) for Fe. The results obtained show that the pollutants of special environmental and health concern are As and Pb. Mean As concentration was higher than the guideline value associated with an excess cancer risk of 1:10⁻⁶, reported by the World Health Organization (WHO). Lead is the only element that showed higher concentrations than those recently measured in the large and heavily trafficked metropolitan area of Buenos Aires. Cadmium>Pb>As>Zn>Cu are the elements more enriched in airborne PM₁₀.     

Grundlagen zur halbquantitativen Bestimmung von zwanzig Elementen in der Lasermikrospektralanalyse

Zusammenfassung Für die folgenden 20 Elemente wurden die Grundlagen für eine halbquantitative Konzentrationsbestimmung mit Hilfe des Laser-Mikrospektralanalysators ermittelt, und zwar differenziert für Untersuchungen an oxidischen und an metallischen Materialien: Mg, Al, Si, Cr, Mn, Co, Ni, Cu, Zn, Ga, Ge, Pd, Ag, Cd, In, Sn, Sb, Pb, Bi, Fe bzw. Au.

---

Principles of semi-quantitative determination of 20 elements by laser-microspectroscopy

The principles for the determination of the following 20 elements by Laser-microspectroscopy have been investigated separately for oxidic and metallic materials: Mg, Al, Si, Cr, Mn, Co, Ni, Cu, Zn, Ga, Ge, Pd, Ag, Cd, In, Sn, Sb, Pb, Bi, Fe resp. Au.

     

Room temperature acid sonication ICP-MS multielemental analysis of milk

Room temperature acid sonication of milk samples is proposed as a fast alternative methodology for the determination of the total content of 45 elements (Li, Al, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Y, Mo, Ag, Cd, In, Sn, U, Sb, Te, Cs, Ba, Hg, Pb, Bi, Th, La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm, Yb, Lu, Hf and Ta) in milk by inductively coupled plasma mass spectrometry (ICP-MS). The aforementioned procedure involves a 10 min sample pre-treatment. Measurements were made in quantitative and semiquantitative (Totalquant^®) modes of analysis using Rh as internal standard and Be, Ge, Tb and Re for internal calibration of the equipment in the semiquantitative mode. The selected isotopes were in general the most abundant ones of each element, except in cases where polyatomic or isobaric interferences were detected. Results of total concentrations in 10 liquid and 11 powdered commercially available milk samples were presented. Method validation was performed by measuring a SRM NIST-1549 non-fat milk powder and through the use of recovery experiments. Additionally, the proposed methodology was compared with a method based on a previous microwave-assisted digestion of samples and a direct analysis of 1:4 diluted samples.     

电感耦合等离子体原子发射光谱法测定马奶酒中的多种元素

电感耦合等离子体原子发射光谱法测定马奶酒中的多种元素嘎日迪,乌地（内蒙古师范大学化学系,配位化学研究所,呼和浩特,０１００２２）关键词电感耦合等离子体原子发射光谱,马奶酒,微量金属元素蒙古民族喜爱的传统饮料──马奶酒（蒙语“策格”）是用鲜马奶为原料发...     

Determination of ultratrace levels of dissolved metals in seawater by reaction cell inductively coupled plasma mass spectrometry after ammonia induced magnesium hydroxide coprecipitation

A method for the determination of ultratrace amounts of Cr, Fe, Mn, Pb and Zn in seawater has been developed. It combined the low-blank magnesium hydroxide coprecipitation procedure with quadrupole inductively coupled plasma mass spectrometry and used the dynamic reaction cell technique to resolve the polyatomic interferences arising from the residual matrix, the solvent and plasma gases. Detection limits (3σ_B, n = 10) for Cr, Fe, Mn, Pb and Zn were 0.02, 0.10, 0.01, 0.002 and 0.19 nM, respectively, using 50 mL of seawater sample. The accuracy of the analytical procedure was verified by the analysis of the seawater reference materials CASS-4, NASS-5, SAFe D2 and SAFe S. The analytical precision ranged from 3% to 16% (n = 6), with a sample throughput of about 6 samples h⁻¹.     

Multielemental Analysis of Camellia Oil by Microwave Dry Ashing and Inductively Coupled Plasma Mass Spectrometry

A simple and practical method is reported for the determination of Mg, Ca, Cr, Mn, Fe, Co, Ni, Cu, Zn, and Pb in camellia oil by inductively coupled plasma-mass spectrometry (ICP-MS). Camellia oil was treated using microwave dry ashing at 380 degree Celsius for carbonization and 550 degree Celsius for ashing in a 110 minute procedure. The operational conditions of the dynamic reaction cell with ammonia as the reaction gas were optimized to minimize interferences. The recoveries and the relative standard deviations of optimized method were between 85.6 and 98.4 percent and 1.1 and 5.5 percent, respectively. The detection limits for Mg, Ca, Cr, Mn, Fe, Co, Ni, Cu, Zn, and Pb were 31, 48, 0.6, 4, 22, 0.4, 0.6, 0.9, 3, and 1 micrograms per kilogram, respectively. The developed method has significant potential for the determination of metals in edible oils.     

电感耦合等离子体原子发射光谱法测定紫斑牡丹胚乳和胚中矿物质元素

为了给离体体细胞胚的人工胚乳配制提供矿物质元素种类和数量方面的参考,用浓硝酸-高氯酸(4∶1)的混合溶液消解紫斑牡丹的胚乳和胚样品,采用电感耦合等离子体-原子发射光谱法(ICP-AES)测定了样品中的(K、Na、Ca、Mg、Fe、Cu、Zn、Mn、Li、Ni、B、Ag、Cd、Pb)14种矿物质元素含量。结果表明:各元素的校准曲线的回归系数在0.9990～0.9999之间,线性良好;方法精密度高,能多元素同时分析;紫斑牡丹胚乳和胚中均含有植物生长必需的K、Ca、Mg 3种大量元素,Fe、Mn、Cu、Zn、Ni、B 6种微量元素,1种有益元素Na,及Li和Pb,Ag、Cd则未被检测到。在被检测到的12种元素中,Mg、Zn、Mn、Fe、K、Na、Li与Ni 8种元素在胚乳中的含量低于胚中的含量,Ca、Cu、Pb与B在胚乳中的含量则高于胚中的含量。     

Certification of the contents of some heavy metals (Cd, Cu, Hg, Ni, Pb and Zn) in three types of soils

Summary The element contents of Cd, Cu, Hg, Ni, Pb and Zn of three types of soil were certified. The preparation, homogeneity and stability are reported. The certified contents as well as values for Co, Cr, Mn and Se and for the aqua regia soluble contents Cd, Cr, Cu, Mn, Ni, Pb and Zn are given.

---

Zertifizierung von Schwermetallspuren (Cd, Cu, Hg, Ni, Pb und Zn) in drei Bodenproben

Zusammenfassung In drei verschiedenen Bodenproben wurden die Elementgehalte an Cd, Cu, Hg, Ni, Pb und Zn zertifiziert. Es wird berichtet über die Bereitung, Homogenität und Stabilität. Die zertifizierten Gehalte sowie der Gehalt an Cr, Co, Mn und Se und der Gehalt an königswasserlöslichem Cd, Cr, Cu, Mn, Ni, Pb und Zn werden angegeben.

     

Geographical Discrimination of Honeysuckle (Lonicera japonica Thunb.) from China by Characterization of the Stable Isotope Ratio and Multielemental Analysis

A total of 117 honeysuckle (Lonicera japonica Thunb.) samples from four major regions of production in China, including Fengqiu in Henan, Pingyi in Shandong, Julu in Hebei, and Xiushan in Chongqing, were analyzed to determine their geographical origin. δ¹³C, δ¹⁵N, and δ¹⁸O values were determined by isotope ratio mass spectrometry (IRMS), and the contents of 18 elements (Fe, Mn, Cu, Zn, K, Ca, Mg, Pb, Cd, Cr, As, Hg, Se, Sr, Ni, Co, B, and Mo) were measured by inductively coupled plasma optical emission spectrometry (ICP-OES) and inductively coupled plasma mass spectrometry (ICP-MS). Multivariate statistical analysis by analysis of variance (ANOVA), principal component analysis (PCA), and linear discriminant analysis (LDA) were performed. The results showed that there were very significant differences in the stable isotope ratios and elemental concentrations in honeysuckle based on geographical origin, with plants from each region having a unique fingerprint. Discriminant functions were established to distinguish the origin of honeysuckle using suitable indicators including Cd, Cr, As, Hg, Se, Co, Ni, Sr, Fe, δ¹³C, δ¹⁵N, and δ¹⁸O. Cross-validated cases of 95.7% were correctly classified.