A coupled damage-plasticity model for the cyclic behavior of shear-loaded interfaces

The present work proposes a novel thermodynamically consistent model for the behavior of interfaces under shear (i.e. mode-II) cyclic loading conditions. The interface behavior is defined coupling damage and plasticity. The admissible states’ domain is formulated restricting the tangential interface stress to non-negative values, which makes the model suitable e.g. for interfaces with thin adherends. Linear softening is assumed so as to reproduce, under monotonic conditions, a bilinear mode-II interface law. Two damage variables govern respectively the loss of strength and of stiffness of the interface. The proposed model needs the evaluation of only four independent parameters, i.e. three defining the monotonic mode-II interface law, and one ruling the fatigue behavior. This limited number of parameters and their clear physical meaning facilitate experimental calibration. Model predictions are compared with experimental results on fiber reinforced polymer sheets externally bonded to concrete involving different load histories, and an excellent agreement is obtained.     

A 3D model of the cyclic thermomechanical behavior of shape memory alloys

The model in the first part of this paper is extended to account for SMA behavior under cyclic loading. To this end, three new state variables are introduced: internal stress B, residual strain ?_r and cumulated martensite volume fraction z_e. Several parameters of the extended model depend on z_e, making them evolve with cyclic phase change. Cyclic SMA effects including training and two-way shape memory are accounted for and several numerical simulations are provided and validated in the case of cyclic superelasticity.     

A micromechanical continuum model for the tensile behavior of shape memory metal nanowires

We have previously discovered a novel shape memory effect and pseudoelastic behavior in single-crystalline face-centered-cubic metal (Cu, Ni, and Au) nanowires. Under tensile loading and unloading, these wires can undergo recoverable elongations of up to 50%, well beyond the recoverable strains of 5-8% typical for most bulk shape memory alloys. This phenomenon only exists at the nanoscale and is associated with a reversible lattice reorientation driven by the high surface-stress-induced internal stresses. We present here a micromechanical continuum model for the unique tensile behavior of these nanowires. Based on the first law of thermodynamics, this model decomposes the lattice reorientation process into two parts: a reversible, smooth transition between a series of phase-equilibrium states and a superimposed irreversible, dissipative twin boundary propagation process. The reversible part is modeled within the framework of strain energy functions with multiple local minima. The irreversible, dissipative nature of the twin boundary propagation is due to the ruggedness of strain energy curves associated with dislocation nucleation, glide, and annihilation. The model captures the major characteristics of the unique behavior due to lattice reorientation and accounts for the size and temperature effects, yielding results that are in excellent agreement with the results of molecular dynamics simulations.     

Thermodynamic based model for the evolution equation of the backstress in cyclic plasticity

A nonlinear kinematic hardening rule is developed here within the framework of thermodynamic principles. The derived kinematic hardening evolution equation has three distinct terms: two strain hardening terms and a dynamic recovery term that operates at all times. The proposed hardening rule, which is referred in this paper as the FAPC (Fredrick and Armstrong–Phillips–Chaboche) kinematic hardening rule, shows a combined form of the Frederick and Armstrong backstress evolution equation, Phillips evolution equation, and Chaboche series rule. A new term is incorporated into the Frederick and Armstrong evolution equation that appears to have agreement with the experimental observations that show the motion of the center of the yield surface in the stress space is directed between the gradient to the surface at the stress point and the stress rate direction at that point. The model is further modified in order to simulate nonproportional cyclic hardening by proposing a measure representing the degree of nonproportionality of loading. This measure represents the topology of the incremental stress path. Numerically, it represents the angle between the current stress increment and the previous stress increment, which is interpreted through the material constants of the kinematic hardening evolution equation. This new kinematic hardening rule is incorporated in a material constitutive model based on the von Mises plasticity type and the Chaboche isotropic hardening type. Numerical integration of the incremental elasto-plastic constitutive equations is based on a simple semi-implicit return-mapping algorithm and the full Newton–Raphson iterative method is used to solve the resulting nonlinear equations. Experimental simulations are conducted for proportional and non-proportional cyclic loadings. The model shows good correlation with the experimental results.     

An updated version of the multimechanism model for cyclic plasticity

In this paper we consider the elastoplastic behavior of the 304L stainless steel under cyclic loading at room temperature. After the experimental investigations presented in Taleb and Hauet (2009), the present work deals with modeling in the light of the new observations. An improved version of the multimechanism model is proposed in which the isotropic variable is revisited in order to take into account the non-proportional effect of the loading as well as the strain memory phenomenon. A particular attention has been paid to the identification process in order to capture the main important phenomena: relative parts of isotropic and kinematic hardening, time dependent effects, non-proportionality effect, strain amplitude dependence. Only strain controlled tests have been used for the identification process. The capabilities of the model with “only” 17 parameters are evaluated considering a number of proportional and non-proportional stress and strain controlled tests.     

Constitutive model for stretch-induced softening of the stress-stretch behavior of elastomeric materials

Elastomeric materials experience stretch-induced softening as evidenced by a pre-stretched material exhibiting a significantly more compliant response than that of the virgin material. In this paper, we propose a fully three-dimensional constitutive model for the observed softening of the stress-strain behavior. The model adopts the Mullins and Tobin concept of an evolution in the underlying hard and soft domain microstructure whereby the effective volume fraction of the soft domain increases with stretch. The concept of amplified strain is then utilized in a mapping of the macroscopic deformation to the deformation experienced by the soft domain. The strain energy density function of the material is then determined from the strain energy of the soft domain and thus evolves as the volume fraction of soft domain evolves with deformation. Comparisons of model results for cyclic simple extension with the experimental data of Mullins and Tobin show the efficacy of the model and suggest that an evolution in the underlying soft/hard domain microstructure of the elastomer captures the fundamental features of stretch-induced softening. Model simulations of the cyclic stress-strain behavior and corresponding evolution in structure with strain for uniaxial tension, biaxial tension and plane strain tension are also presented and demonstrate three-dimensional features of the constitutive model.     

A unified plasticity model for cyclic behaviour of clay and sand

This paper presents the development and an experimental evaluation of a simple unified bounding surface plasticity theory for modelling the stress–strain behaviour of sand and clay under both drained and undrained cyclic loading conditions. The model concerned is called CASM-c, which is based on the unified critical state model CASM developed by Yu [Yu, H.S., 1995. A unified critical state model for clay and sand. Civil Engineering Research Report No. 112.08.1995. University of Newcastle, NSW 2308, Australia; Yu, H.S., 1998. CASM: a unified state parameter model for clay and sand. International Journal of Numerical and Analytical Methods in Geomechanics 22, 621–653]. CASM is a relatively simple model as it only requires seven model constants, five of which are the same as those used in the modified Cam-clay model. All these constants have clear physical meanings and may be easily determined from the results of triaxial tests. A key advantage of CASM over many other existing critical state models lies on its simplicity and unified nature as it can model the behaviour of both clay and sand.The extension of the model CASM presented in this paper consists of adopting the bounding surface plasticity theory and treating the reloading and unloading processes differently when calculating the hardening modulus. As a result, a smooth transition of stiffness and gradual accumulation of permanent strain and/or pore pressure in unload–reload cycles as well as the hysteretic behaviour can be reproduced. The results of model simulations show an encouraging agreement with experimental data from triaxial tests subjected to both one-way and two-way cyclic loading conditions.     

A method for the evaluation of design limits for structural materials in a cyclic state of creep

The purpose of the present paper is to demonstrate how the minimum theorems proposed in an accompanying paper (Ponter and Boulbibane, 2002) can be utilised in the prediction of the deformation and life assessment of structures subjected to cyclic mechanical and thermal loadings. The developed method, which is based upon bounding theorems and an associate programming method, the Linear Matching method, takes into account the changes in residual stress field occurring within a cycle. Although the solution provided a bound on the inelastic work, it also appears that generally the displacements predicted by this solution are smaller than those that would be predicted by the rapid cycle solution. By way of illustration a simple non-linear viscous model is adopted and a number of solutions are presented involving a Bree plate problem subjected to cyclic histories of load and temperature. An elastic follow-up factor is identified as a key design parameter for high temperature dwell periods.     

A macroscopic multi-mechanism based constitutive model for the thermo-mechanical cyclic degeneration of shape memory effect of NiTi shape memory alloy

A macroscopic based multi-mechanism constitutive model is constructed in the framework of irreversible thermodynamics to describe the degeneration of shape memory effect occurring in the thermo-mechanical cyclic deformation of NiTi shape memory alloys(SMAs). Three phases,austenite A, twinned martensite Mtand detwinned martensite M~d, as well as the phase transitions occurring between each pair of phases( A → M~t, M~t→ A, A → M~d,M~d→ A, and M~t→ M~d) are considered in the proposed model. Meanwhile, two kinds of inelastic deformation mechanisms, martensite transformation-induced plasticity and reorientation-induced plasticity, are used to explain the degeneration of shape memory effects of NiTi SMAs. The evolution equations of internal variables are proposed by attributing the degeneration of shape memory effect to the interaction between the three phases(A, M~t, and M~d) and plastic deformation. Finally, the capability of the proposed model is verified by comparing the predictions with the experimental results of NiTi SMAs. It is shown that the degeneration of shape memory effect and its dependence on the loading level can be reasonably described by the proposed model.     

A model for the nonisothermal behavior of viscoelastic media

Summary A new constitutive model is derived for the viscoelastic behavior of polymers under non-isothermal loading. The model extends the concept of adaptive links (entanglements) between polymeric molecules to thermoviscoelastic media. By using experimental data for Nylon-6 and polyisobutylene in the vicinity of the glass-transition temperature, we find parameters of the model and study their dependence on temperature. The model is employed for the numerical analysis of the material response to time-periodic loads under isothermal conditions and to time-varying loads under heating. The results of numerical simulation demonstrate fair agreement with experimental data. Accepted for publication 23 May 1996     

Tension–compression asymmetry of phosphor bronze for electronic parts and its effect on bending behavior

In-plane tension and compression experiments on copper alloy sheets (phosphor bronze) and 6000 series aluminum alloy sheets (AA6016-T4) were conducted using a specially designed testing apparatus. The apparatus is equipped with comb-type dies so that stress–strain curves of a sheet specimen subjected to tension followed by compression, and vice versa, can be measured without buckling of the specimen, as well as those for monotonic tension and compression. A difference was observed in the flow stresses between tension and compression for the as-received copper alloy, but not for the aluminum alloy. Moreover, stress reversal tests, such as tension followed by compression and compression followed by tension, were carried out in order to measure the Bauschinger effect. In the second part of the experiment, bending moment–curvature diagrams were measured for the as-received and pre-stretched specimens. The bending moment–curvature diagrams were compared with those calculated using the stress–strain curves obtained from the tension–compression tests, and were in good agreement with those calculated with the tension–compression asymmetry and the Bauschinger effect correctly reproduced.     

A combined isotropic-kinematic hardening model for the simulation of warm forming and subsequent loading at room temperature

A coupled isotropic-kinematic hardening material model was developed based on phenomenological observations of performed two stage experiments on a medium carbon steel – SAE 1144, where the first deformation is performed at elevated temperatures and the second deformation at room temperature. Above all, deformations with orthogonal loading at various temperatures were investigated in order to determine the influence of the loading direction as well as of the temperature. Bergström’s theory of work hardening as well as the nonlinear kinematic hardening of an Armstrong–Frederick type were used as a basis for the model development. In the proposed model a relationship between material coefficients of the classical Bergström model and temperature was investigated. The aim of the new material model was to introduce the least possible amount of new parameters as well as to facilitate the mathematical determination of parameters during the fitting of the model with experimental data. The developed model was implemented in an in-house FE-Code in order to simulate the material behavior due to the dynamic strain aging and the hardening behavior after the dynamic strain aging process. Representative simulation results were compared with the experimental data in order to validate the efficiency and the application range of the model.     

Combining the logarithmic strain and the full-network model for a better understanding of the hyperelastic behavior of rubber-like materials

Suitably defined invariants of the logarithmic strain are shown to be more adequate than the usual invariants of the left Cauchy-Green tensor to define the type and intensity of a strain applied to hyperelastic rubber-like materials. Coupling these invariants with the macromolecular full-network model clarifies some features of the state of strain dependence of these materials. Finally, comparisons of the model with experimental data illustrate the efficiency of the full-network model and the dependence of the material parameters on the applied loading history.     

Experimental investigation and modeling of the tension behavior of polycarbonate with temperature effects from low to high strain rates

The effects of strain rate and temperature on the tension stress–strain responses of polycarbonate are experimentally investigated over a wide range of strain rates (0.001–1700 s⁻¹) and temperatures (0–120 °C). A modified split Hopkinson tension bar is used for high-rate uniaxial tension tests. Experimental results indicate that the stress–strain responses of polycarbonate at high strain rates exhibit the nonlinear characteristics including the obvious yielding and strain softening. The tension behavior is strongly dependent on the strain rate and temperature. The values of yield stress and strain at yield present a dramatic increase at higher strain rates and decrease with the increase in temperature. Moreover, there exists a significant rate-sensitivity transition in the polycarbonate tension yield behavior. Based on the experimental investigation, a physically based three-dimensional elastoplastic constitutive model for the finite deformation of glassy polymers is used to characterize the rate-temperature dependent yield and post-yield behavior of polycarbonate when subjected to tension loading. The model results are shown close to the experimental data within the investigated strain-rate and temperature ranges.     

Conjugate model for heat and mass transfer of porous wall in the high temperature gas flow

Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency. The project supported by the National Natural Science Foundation of China (19889209) and Russian Foundation for Basic Research (97-02-16943)     

Suitability of the k–ω turbulence model for scramjet flowfield simulations

The suitability of Wilcox's 2006 k– ω turbulence model for scramjet flowfield simulations is demonstrated by validation against five test cases that have flowfields representative of those to be expected in scramjets. The five test cases include a 2D flat plate, an axisymmetric cylinder, a backward‐facing step, the mixing of a pair of coaxial jets and the interaction between a shock wave and turbulent boundary layer. A generally good agreement between the numerical and experimental results is obtained for all test cases. These tests reveal that despite the turbulence model's sensitivity to freestream turbulence properties, the numerically predicted skin friction agrees with experimental data and theoretical correlations to their degree of uncertainty. The tests also confirm the importance of using a y⁺ value of less than 1 in getting accurate surface heat transfer distributions. In the coaxial jets case, the importance of matching the turbulence intensities at the inflow plane in improving the predictions of the turbulent mixing phenomena is also shown. A review of guidelines with regard to the setting up of grids and specification of freestream turbulence properties for turbulent Reynolds‐averaged Navier–Stokes CFD simulations is also included in this paper. Copyright © 2011 John Wiley & Sons, Ltd.     

Développement d''un modèle en vue de la prédiction du rallumage d''un foyer de turboréacteur à haute altitudeDevelopment of a model to predict the ignition performance of a turbojet engine at high altitude

Within the context of turbojet engine re-ignition after in-flight extinction, a thermo-diffusive model has been developed to describe the electrical ignition, at low pressure and low temperature, of a cluster of fuel droplets. The model involves the resolution of the conservation equations of mass, species and energy. It also takes into account the various physical and chemical phenomena occurring during the ignition process. This Note presents the ignition model and preliminary results of this model applied to an experimental configuration. To cite this article: V. Quintilla et al., C. R. Mecanique 330 (2002) 811–818.     

Identification of the scatter in high cycle fatigue from temperature measurementsIdentification de la dispersion des limites d'endurance à l'aide d'un essai d'échauffement.

It is proposed to determine the scatter in a Wöhler diagram by analyzing temperature changes induced by microplasticity. A unified framework is introduced to study both phenomena. The identification procedure is applied to a dual-phase steel. To cite this article: C. Doudard et al., C. R. Mecanique 332 (2004).