Evaporation of water droplets on polymer surfaces

The evaporation of water droplets on polymer surfaces was investigated by using a digital image analysis technique. There were three distinct stages in the water evaporation process: a constant contact area mode, a constant contact angle mode, and a mixed mode that is independent of both the initial quantity of water droplets and the hydrophobic properties of the polymer surfaces. The physical factors influencing the first and second transitions in the evaporation process were found to be the attainment of the receding angle on the polymer surfaces and the Marangoni instability in the evaporating water droplets, which result from the concentration gradient of contaminants. This study also provides qualitative information about the microfluid flows inside the evaporating water droplets and the morphology of drying stains on polymer surfaces. The contaminants were found to be concentrated at the perimeter of the stains, in agreement with the observed outward microfluid flow in the mixed mode of the evaporation process.     

Effect of surface morphology on measurement and interpretation of boundary slip on superhydrophobic surfaces

Highly liquid repellent surfaces have been obtained by the combination of roughness and hydrophobicity. Studies have reported that the flow over such surfaces exhibits larger boundary slip as compared to the smooth hydrophobic surfaces. However, the surface roughness can also lead to apparent slip. Thus, the effect of the two factors, that is, wettability and roughness, needs to be segregated. In this study, we have measured the slippage of water on rough hydrophilic and hydrophobic surfaces using colloidal probe atomic force microscopy technique (CP‐AFM). Results showed that the effect of surface roughness on the measured slip is dominant over that of wettability. It was also found that slip on surfaces with sparsely distributed asperities is highly local and measurements on various locations give dissimilar results. The results suggested that the main reason of the larger slip, on rough hydrophobic surfaces, is likely to be the roughness and not the hydrophobicity. Moreover, it was also found that the slip does not vary considerably with the increase or decrease in the shear rate. Most likely, this kind of slip phenomena is caused by the apparent decrease of the drag force, because the nanoasperities on the surface restrict the probe from reaching the surface properly. Copyright © 2016 John Wiley & Sons, Ltd.     

Dynamic effects of bouncing water droplets on superhydrophobic surfaces

Superhydrophobic surfaces have considerable technological potential for various applications due to their extreme water repellent properties. Superhydrophobic surfaces may be generated by the use of hydrophobic coating, roughness, and air pockets between solid and liquid. Dynamic effects, such as the bouncing of a droplet, can destroy the composite solid-air-liquid interface. The relationship between the impact velocity of a droplet and the geometric parameters affects the transition from the solid-air-liquid interface to the solid-liquid interface. Therefore, it is necessary to study the dynamic effect of droplets under various impact velocities. We studied the dynamic impact behavior of water droplets on micropatterned silicon surfaces with pillars of two different diameters and heights and with varying pitch values. A criterion for the transition from the Cassie and Baxter regime to the Wenzel regime based on the relationship between the impact velocity and the parameter of patterned surfaces is proposed. The trends are explained based on the experimental data and the proposed transition criterion. For comparison, the dynamic impact behavior of water droplets on nanopatterned surfaces was investigated. The wetting behavior under various impact velocities on multiwalled nanotube arrays also was investigated. The physics of wetting phenomena for bouncing water droplet studies here is of fundamental importance in the geometrical design of superhydrophobic surfaces.     

Literature review on superhydrophobic self‐cleaning surfaces produced by electrospinning

Self‐cleaning surface is potentially a very useful addition for many commercial products due to economic, aesthetic, and environmental reasons. Super‐hydrophobic self‐cleaning, also called Lotus effect, utilizes right combination of surface chemistry and roughness to force water droplets to form high contact angle on a surface, easily roll off a surface and pick up dirt particles on its way. Electrospinning is a promising technique for creation of superhydrophobic self‐cleaning surfaces owing to a wide set of parameters that allow effectively controlling roughness of resulted webs. This article gives a brief introduction to the theory of super‐hydrophobic self‐cleaning and basic principles of the electrospinning process and reviews the scientific literature where electrospinning was used to create superhydrophobic surfaces. The article reviewed are categorized into several groups and their results are compared in terms of superhydrophobic properties. Several issues with current state of the art and highlights of important areas for future research are discussed in the conclusion. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Condensation and freezing of droplets on superhydrophobic surfaces

Superhydrophobic coatings are reported as promising candidates for anti-icing applications. Various studies have shown that as well as having ultra water repellency the surfaces have reduced ice adhesion and can delay water freezing. However, the structure or texture (roughness) of the superhydrophobic surface is subject to degradation during the thermocycling or wetting process. This degradation can impair the superhydrophobicity and the icephobicity of those coatings. In this review, a brief overview of the process of droplet freezing on superhydrophobic coatings is presented with respect to their potential in anti-icing applications. To support this discussion, new data is presented about the condensation of water onto physically decorated substrates, and the associated freezing process which impacts on the freezing of macroscopic droplets on the surface.     

Fabrication of biomimetic superhydrophobic surfaces by a simple flame treatment method

A simple flame treatment method was explored to construct micro/nanostructures on a surface and then fabricate a biomimetic superhydrophobic surface at a relatively low cost. SiO₂‐containing polydimethylsiloxane (PDMS) was used as a substrate. The PDMS replicas with various micropatterned surfaces were fabricated using grass leaf, sand paper, and PET sheet with parallel groove geometry as templates via PDMS replica molding. The PDMS replica surfaces with micron structures and the surface of a flat PDMS sheet as a control sample were further treated by flame. The fabricated surfaces were characterized by scanning electron microscopy and water contact angle measurements. The effect of surface microstructures on the transparency of PDMS was also investigated. The studies indicate that the fine nanoscale structures can be produced on the surfaces of PDMS replicas and a flat PDMS sheet by a flame treatment method, and that the hierarchical surface roughness can be adjusted and controlled by varying the flame treatment time. The flame‐treated surfaces of PDMS replicas and a flat PDMS sheet possess superhydrophobicity and an ultra‐low sliding angle reaching a limiting value of 1°, and the anisotropic wettability of the PDMS replica surface with oriented microgroove structures can be greatly suppressed via flame treatment. The visible light transmittance of the flame‐treated flat PDMS surface decreases with prolonged flame treatment times. Copyright © 2016 John Wiley & Sons, Ltd.     

Molecular dynamics simulations of water droplets on polymer surfaces

Molecular dynamics simulations were used to study the wetting of polymer surfaces with water. Contact angles of water droplets on crystalline and two amorphous polyethylene (PE) and poly(vinyl chloride) (PVC) surfaces were extracted from atomistic simulations. Crystalline surfaces were produced by duplicating the unit cell of an experimental crystal structure, and amorphous surfaces by pressing the bulk polymer step by step at elevated temperature between two repulsive grid surfaces to a target density. Different-sized water droplets on the crystalline PE surface revealed a slightly positive line tension on the order of 10(-12)-10(-11) N, whereas droplets on crystalline PVC did not yield a definite line tension. Microscopic contact angles produced by the simple point charge (SPC) water model were mostly a few degrees smaller than those produced by the extended SPC model, which, as the model with lowest bulk energy, presents an upper boundary for contact angles. The macroscopic contact angle for the SPC model was 94 degrees on crystalline PVC and 113 degrees on crystalline PE. Amorphicity of the surface increased the water contact angle on PE but decreased it on PVC, for both water models. If the simulated contact angles on crystalline and amorphous surfaces are combined in proportion to the crystallinity of the polymer in question, simulated values in relatively good agreement with measured values are obtained.     

Superhydrophobic surfaces with low and high adhesion made from mixed (hydrocarbon and fluorocarbon) 3,4‐propylenedioxythiophene monomers

This work concerns new superhydrophobic surfaces, generated by replacing long fluorocarbon chains, which bioaccumulate, with short chains whilst at the same time retaining oleophobic properties. Here, is described the synthesis of novel 3,4‐propylenedioxythiophene derivatives containing both a short fluorocarbon chain (perfluorobutyl) and a hydrocarbon chain of various lengths (ethyl, butyl and hexyl). Superhydrophobic (θ_water > 150°) surfaces with good oleophobic properties (60° > θ_hexadecane > 80°) have been obtained by electrodeposition using cyclic voltammetry. Surprisingly, the lowest hystereses and sliding angles (Lotus effect) are obtained with the shortest alkyl chains due to the presence of microstructures made of nanofibers on the surfaces, whereas, the longest alkyl chains leads to nanosheets with high adhesion (Petal effect). Such materials are potential candidates for biomedical applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 782–788     

Evaporation of sessile droplets of dilute aqueous solutions containing sodium n-alkylates from polymer surfaces: influences of alkyl length and concentration of solute

The evaporation of sessile droplets placed on polymer surfaces was studied by microscopic observation of the changes in shape of aqueous solution droplets in which the alkyl lengths and the initial concentrations of sodium n-alkylates were varied. Although the initial contact angles of the droplets were not significantly different, the evaporation process varied significantly with the alkyl length of the sodium n-alkylate employed. For the sodium dodecanoate (C 12), showing the highest surface activity, the concentration was found to have a significant effect on the evaporation process of the droplets. In the evaporation of water droplets, variations in the three distinct stages were caused by the different concentration of solutes distributed near or at the air/water interface. It is revealed that the concentration of droplet solute near the air/water interface requires not only solvent evaporation but also some affinity of the solute for the interface. The initial C 12 concentration-dependence of the evaporation of C 12 solution droplets is discussed with particular emphasis on the sudden spreading or sudden contraction of the contact area near the end of evaporation. It is suggested that the cluster formation by C 12 molecules at the air/liquid interface during the evaporation causes Marangoni instability in an evaporating droplet, and the clusters are expected to move dynamically, depending on the droplet concentration of C 12, from the droplet center to the contact line and vice versa, showing Marangoni flow along the air/water interface.     

Preparation of a superhydrophobic rough surface

The relationship between the contact angles, surface tension, and surface roughness is reviewed. Numerical formulas related to the superhydrophobic rough surfaces of polymers are predicted with two approaches, the Wenzel and Cassie–Baxter models. With these models as a guide, an artificial superhydrophobic surface is created. Rough nylon surfaces mimicking the lotus leaf are created by the coating of a polyester surface with nylon‐6,6 short fibers via the flocking process. Poly(acrylic acid) chains aregrafted onto nylon‐6,6 surfaces, and this is followed by the grafting of 1H,1H‐perfluorooctylamine onto the poly(acrylic acid) chains. Water contact angles as high as 178° are achieved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 253–261, 2007.