Kinetics of substitution of aqua ligands from cis‐diaqua (ethylenediamine)platinum(II) perchlorate by L‐asparagine in aqueous medium

The kinetics of the interaction of L ‐asparagine with [Pt(ethylenediamine)(H₂O)₂]²⁺ have been studied spectrophotometrically as a function of [Pt(ethylenediamine)(H₂O)₂²⁺], [L ‐asparagine], and temperature at pH 4.0, where the substrate complex exists predominantly as the diaqua species and L ‐asparagine as the zwitterion. The substitution reaction shows two consecutive steps: the first step is the ligand‐assisted anation and the second one is the chelation step. Activation parameters for both the steps have been calculated using Eyring equation. The low ΔH₁^≠ (43.59 ± 0.96 kJ mol^?1) and large negative values of ΔS₁^≠ (?116.98 ± 2.9 J K^?1 mol^?1) as well as ΔH₂^≠ (33.78 ± 0.51 kJ mol^?1) and ΔS₂^≠ (?221.43 ± 1.57 J K^?1 mol^?1) indicate an associative mode of activation for both the aqua ligand substitution processes. © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 35: 252–259, 2003     

Kinetics and mechanism of the reaction of Ba(No3)2 with TiO2(anatase) in the solid-solid state and the liquid-solid state

The reaction of Ba(NO₃)₂ with TiO₂(anatase) was studied by TG and DTA. According to simultaneous TG and DTA, the reaction occurred sharply around the melting temperature of Ba(NO₃)₂, ～577°C, at low heating rates, and the reaction followed after melting of Ba(NO₃)₂ as the rate was raised. For the isothermal reactions the conversion α vs time relationship was given by the equation: kt = 1 - (1-α)^1/3. The relationship was shown by one straight line below 577°C, and by two lines with a bend above 577°C. The reaction rates at the earlier period above 577°C were about $\text{1}\text{5}$ smaller than those at the later period, which were nearly on the extrapolated log k vs 1/T line obtained below 577°C. The activation energy was 212 kJ mol^?1 for the solid-solid reaction and 231 kJ mol^?1 for the earlier period in the liquid-solid reaction.     

Kinetic parameters and solid state mechanism of the thermal dehydration of trans[CrF(H2O)(aa′)2]K[Cr(CN)6]H2O And trans[CrF(H2O)(aa′)2]K[CrNO(CN)5]H2O (aa′=ethylenediamine or 1,3-diaminopropane)

The solid phase thermal deaquation of trans[CrF(H₂O)(aa′)₂]K[Cr(CN)₆]H₂O and trans[CrF(H₂O)(aa′)₂]K[CrNO(CN)₅]H₂O (aa′=ethylenediamine or 1,3-diaminopropane) has been investigated by means of TG measurements. The kinetic parameters (activation energy, E_a, activation entropy, ΔS^#, and frequency factor, k₀) have been determined by comparison of the isothermal and non-isothermal studies for all the principal g(α) expressions. The values found for the activation energy are low (between 80 and 110 kJ mole^?1, approximately) and permit the assignment of the deaquation-anation mechanism of the S_N1 type, involving square-pyramid activated complex and elimination of water as Frenkel defects.     

Thermal decomposition and non-isothermal decomposition kinetics of carbamazepine

The thermal stability and kinetics of isothermal decomposition of carbamazepine were studied under isothermal conditions by thermogravimetry (TGA) and differential scanning calorimetry (DSC) at three heating rates. Particularly, transformation of crystal forms occurs at 153.75°C. The activation energy of this thermal decomposition process was calculated from the analysis of TG curves by Flynn-Wall-Ozawa, Doyle, distributed activation energy model, ?atava-?esták and Kissinger methods. There were two different stages of thermal decomposition process. For the first stage, E and logA [s^?1] were determined to be 42.51 kJ mol^?1 and 3.45, respectively. In the second stage, E and logA [s^?1] were 47.75 kJ mol^?1 and 3.80. The mechanism of thermal decomposition was Avrami-Erofeev (the reaction order, n = 1/3), with integral form G(α) = [?ln(1 ? α)]^1/3 (α = ～0.1–0.8) in the first stage and Avrami-Erofeev (the reaction order, n = 1) with integral form G(α) = ?ln(1 ? α) (α = ～0.9–0.99) in the second stage. Moreover, ΔH ^≠, ΔS ^≠, ΔG ^≠ values were 37.84 kJ mol^?1, ?192.41 J mol^?1 K^?1, 146.32 kJ mol^?1 and 42.68 kJ mol^?1, ?186.41 J mol^?1 K^?1, 156.26 kJ mol^?1 for the first and second stage, respectively.     

Kinetics and mechanism of the interaction of adenosine with cis‐diaqua(cis‐1,2‐diaminocyclohexane)platinum(II) perchlorate in aqueous medium

The kinetics of the interaction of adenosine with cis‐[Pt(cis‐dach)(OH₂)₂]²⁺ (dach = diaminocyclohexane) was studied spectrophotometrically as a function of [cis‐[Pt(cis‐dach)(OH₂)₂]²⁺], [adenosine], and temperature at a particular pH (4.0), where the substrate complex exists predominantly as the diaqua species and the ligand adenosine exists as a neutral molecule. The substitution reaction shows two consecutive steps: the first is the ligand‐assisted anation followed by a chelation step. The activation parameters for both the steps have been evaluated using Eyring equation. The low negative value of ΔH^≠₁ (43.1 ± 1.3 kJ mol^?1) and the large negative value of ΔS^≠₁ (?177 ± 4 J K^?1 mol^?1) along with ΔH^≠₂ (47.9 ± 1.8 kJ mol^?1) and ΔS^≠₂ (?181 ± 6 J K^?1 mol^?1) indicate an associative mode of activation for both the aqua ligand substitution processes. The kinetic study was substantiated by infrared and electrospray ionization mass spectroscopic analysis. © 2011 Wiley Peiodicals, Inc. Int J Chem Kinet 43: 219–229, 2011     

Thermal Decompositions of the Molybdotellurates of Nickel(II) and Cobalt(II)

Molybdotellurates [M(H₂O)₆]₃·[TeMo₆O₂₄], with M=Ni(II) and Co(II), were synthesized and characterized by single-crystal X-ray diffraction for compound 1 and X-ray powder diffraction for compound 2, EDAX, IR, electronic spectra in the solid phase and in solution, and magnetic properties. Thermogravimetry and differential scanning calorimetry of both compounds revealed a loss of 11 water molecules through an endothermal process with ΔH=800 kJ mol⁻¹ for the nickel compound and ΔH=833 kJ mol⁻¹ for the cobalt compound. The residual compounds were characterized by chemical analysis, IR and XPS spectroscopy This revised version was published online in July 2006 with corrections to the Cover Date.     

The solid state reactions of o-aminobenzoic acid with Zn(Ⅱ), Cu(Ⅱ), Ni(Ⅱ), Mn(Ⅱ) acetate hydrate at room temperature

The solid-solid state reactions of o-aminobenzoic acid with Zn(OAc)2.2H2O, Cu(OAc)2 .H2O, Ni(OAc)2.4H2O and Mn(OAc)2.4H2O result in the formation of corresponding complexes M(OAB)2 (M = Zn(Ⅱ), Cu(Ⅱ), Ni(Ⅱ), Mn(IⅡ)). XRD, IR and elemental analysis methods have been used to characterize the solid products. The activation energies of these reactions, which are calculated from the kinetic data obtained by means of the isothermal electrical conductivity measurement method, have been found to increase in the order: Cu(OAc)2.H2O(37.7 kJ.mol-1)~Mn(OAc)2.4H2O (39.7kJ.mol-1) < Zn(OAc)2.2H2O (56.3 kJ.mol-1) < Ni(OAc)2.4H2O (85.2 kJ.mol-1). The trend is related to their crystal structures.     

Bonding modes of nitrite and nitrate in palladium(II) and platinum(II) complexes

The crystal structures of the well-known complexes, [(Me₄en)M(II)X₂] (Me₄en?=?N,N,N??,N??-tetramethylethylenediamine; M(II)?=?Pd(II) or Pt(II); X ^??=?NO₂ ^? or NO₃ ^?) have been determined. For [(Me₄en)Pd(NO₂)₂] and [(Me₄en)Pt(NO₂)₂], the nitrite anion acts as a monodentate N-donor ligand in the solid state. In contrast, for [(Me₄en)Pd(ONO₂)(O₂NO)], the two nitrate anions act as a monodentate O-donor (ONO₂) and a bidentate O,O??-donor (O₂NO). Recrystallization of [(Me₄en)Pt(NO₃)₂] from Me₂SO yields the Me₂SO adduct with a monodentate O-donor nitrate and a counteranionic nitrate, [(Me₄en)Pt(ONO₂)(S-Me₂SO)](NO₃). The solution behavior of these complexes, including the equilibrium between coordinated and free Me₂SO, has been investigated.     

Non-isothermal decomposition kinetics of diosgenin

The thermal stability and kinetics of isothermal decomposition of diosgenin were studied by thermogravimetry (TG) and Differential Scanning Calorimeter (DSC). The activation energy of the thermal decomposition process was determined from the analysis of TG curves by the methods of Flynn-Wall-Ozawa, Doyle, ?atava-?esták and Kissinger, respectively. The mechanism of thermal decomposition was determined to be Avrami-Erofeev equation (n = 1/3, n is the reaction order) with integral form G(α) = [?ln(1 ? α)]^1/3 (α = 0.10–0.80). E _a and logA [s^?1] were determined to be 44.10 kJ mol^?1 and 3.12, respectively. Moreover, the thermodynamics properties of ΔH ^≠, ΔS ^≠, and ΔG ^≠ of this reaction were 38.18 kJ mol^?1, ?199.76 J mol^?1 K^?1, and 164.36 kJ mol^?1 in the stage of thermal decomposition.     

Thermal decomposition of poly(α,α,α′,α′-tetrafluoro-p-xylylene) in nitrogen and oxygen

The thermal decomposition of poly(α,α,α′,α′-tetrafluoro-p-xylylene) (parylene AF-4) films with thicknesses of ca. 7.5 and 10 μm has been studied by both dynamic (10°C min^?1) and isothermal TG in either nitrogen or oxygen atmospheres. In dynamic studies with nitrogen, gross decomposition occurs between 546.7±1.4 and 589.0±2.6°C, with 26.8±4.4% of the initial mass remaining at 700°C. With oxygen as the purge gas, the onset of decomposition shifts slightly to 530.8±4.2°C. The end of the transition at 587.4±2.6°C is within experimental error of the nitrogen value, but no polymer remains above 600°C. Isothermal data were obtained at 10°C intervals from 420 to 490°C in nitrogen, and from 390 to 450°C in oxygen. Plots of log(Δ%wt/Δt)vs. T^?1 are linear throughout the specified range for oxygen and from 420 to 470°C for nitrogen. The calculated activation energies of (147±16) kJ mol^?1 and (150±12) kJ mol^?1 in N₂ and O₂, respectively, are equal within experimental error.     

Further Studies of Nitrodithioacetates of Ni(II), Pd(II) and Pt(II)

Abstract

Ni(II), Pd(II), and Pt(II) complexes of NO₂CHCS₂ ^?2 have been prepared, and their i.r and u.v spectra described. Spectroscopic evidence is presented to substantiate the existence of the new species K₂Ni(NO₂CHCS₂)₂S, a dithio-perthio carboxylate complex.     

The coordination chemistry of simple phospholes: Complexes of nickel(II), palladium(II) and platinum(II)

The reactions between four very simply substituted phospholes and the chlorides of Ni(II), Pd(II) and Pt(II) are described. The phospholes 1-phenylphosphole, 3-methyl-1-phenyl-phosphole and 3,4dimethyl-1-phenylphosphole all readily form bis-complexes of formula L₂MCl₂ [L = phosphole ligand and M = Ni(II), Pd(II) or Pt(II)] or tris-complexes of formula L₃MCI₂. 1-n-Butyl-3,4-dimethylphosphole appears to form stable complexes only with Ni(II). Evidence is put forward which indicates that the L₂MCl₂ complexes exist in a four-coordinate, square-planar monomeric/five coordinate equilibrium while the L₃MCl₂ complexes are primarily the ionic species [L₃MCl]⁺ Cl^? in solution. Comparisons are made with the behaviour of other simple phospholes which do not form Ni(II) complexes and the results are discussed briefly in terms of both aromatic and non-aromatic phosphole models.     

Vapor pressure, kinetics and enthalpy of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II)

The kinetics of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II), [Cu(tmhd)₂] was studied by non-isothermal and isothermal thermogravimetric (TG) methods. The non-isothermal sublimation activation energy values determined following the procedures of Friedman, Kissinger, and Flynn–Wall methods yielded 93 ± 5, 67 ± 2, and 73 ± 4 kJ mol⁻¹, respectively and the isothermal sublimation activation energy was found to be 97 ± 3 kJ mol⁻¹ over the temperature range of 375–435 K. The dynamic TG run proved the complex to be completely volatile and the equilibrium vapor pressure (p_e)_T of the complex over the temperature range of 375–435 K determined by a TG-based transpiration technique, yielded a value of 96 ± 2 kJ mol⁻¹ for its standard enthalpy of sublimation (Δ_subH°).     

Thermal behavior study and decomposition kinetics of salbutamol under isothermal and non-isothermal conditions

The thermal decomposition of salbutamol (β₂ — selective adrenoreceptor) was studied using differential scanning calorimetry (DSC) and thermogravimetry/derivative thermogravimetry (TG/DTG). It was observed that the commercial sample showed a different thermal profile than the standard sample caused by the presence of excipients. These compounds increase the thermal stability of the drug. Moreover, higher activation energy was calculated for the pharmaceutical sample, which was estimated by isothermal and non-isothermal methods for the first stage of the thermal decomposition process. For isothermal experiments the average values were E _act=130 kJ mol⁻¹ (for standard sample) and E _act=252 kJ mol⁻¹ (for pharmaceutical sample) in a dynamic nitrogen atmosphere (50 mL min⁻¹). For non-isothermal method, activation energy was obtained from the plot of log heating rates vs. 1/T in dynamic air atmosphere (50 mL min⁻¹). The calculated values were E _act=134 kJ mol⁻¹ (for standard sample) and E _act=139 kJ mol⁻¹ (for pharmaceutical sample).     

Dinuclear complexes with a μ-cyano ligand. Part VIII(1). Synthesis and characterization of several derivatives ofcis-[CrX(H2O)(en)2]2+ (X=Cl or Br)

Summary The new complex double saltscis-[CrX(H₂O)(en)₂][M(CN)₄] (X=Cl or Br; M=Ni, Pd or Pt) have been synthesised and by anation either in the solid-state or in non-aqueous solvents the corresponding new dinuclear complexes with cyano bridgecis-[(en)₂XCr-NC-M(CN)₃] have been prepared. The complexes have been characterized by chemical analysis and by i.r. and electronic spectroscopy. Powder diffraction patterns indicate that the double salts are isostructural within each series. On the other hand, the dinuclear complexes show low crystallinity. The two dinuclear complexes derived from [Pt(CN)₄]^2– show strong Pt-Pt interactions both in the solid state and in solution.     

The platinum—carbon bond strength in Pt(PPh3)2(Cl)(CPhCHPh)

The enthalpies of the reactions 1 and 2 have been determined as ΔH = Pt(PPh₃)₂(CPhCPh)_cryst. + HCl_g → Pt(PPh₃)₂(Cl)(CPhCHPh)_cryst. (1) Pt(PPh₃)₂(CPhCPh)_cryst. + 2HCl_g → cis-Pt(PPh₃)₂Cl_2cryst. + trans-CHPhCHPh_g (2) ?90.2 ± 6 and ΔH = ?139.0 ± 16 kJ mol^?1, respectively; dissociation energies of bonds involving platinum are expressed by the relationship: 41 kJ mol^?1 + D(Pt-tolane) = 2D(PtCPhCHPh) = {D₁(PtCl) + D₂(PtCl)} ?350 kJ mol^?1     

Reduction from copper(II) to copper(I) upon collisional activation of (pyridine)2CuCl+

Electrospray ionization of dilute aqueous solutions of copper(II) chloride‐containing traces of pyridine (py) as well as ammonia permits the generation of the gaseous ions (py)₂Cu⁺ and (py)₂CuCl⁺, of which the latter is a formal copper(II) compound, whereas the former contains copper(I). Collision‐induced dissociation of the mass‐selected ions in an ion‐trap mass spectrometer (IT‐MS) leads to a loss of pyridine from (py)₂Cu⁺, whereas an expulsion of atomic chlorine largely prevails for (py)₂CuCl⁺. Theoretical studies using density functional theory predict a bond dissociation energy (BDE) of BDE[(py)₂Cu⁺ ‐Cl] = 125 kJ mol^?1, whereas the pyridine ligand is bound significantly stronger, i.e. BDE[(py)CuCl⁺ ‐py] = 194 kJ mol^?1 and BDE[(py)Cu⁺ ‐py] = 242 kJ mol^?1. The results are discussed with regard to the influence of the solvation on the stability of the Cu^I/Cu^II redox couple. Copyright © 2010 John Wiley & Sons, Ltd.     

Water-Exchange Mechanism of Tetraaquapalladium(II). A Variable-Pressure and Variable-Temperature Oxygen-17 NMR Study

Water exchange of square-planar Pd(H₂O)²₄⁺ has been studied as a function of temperature (240 to 345 K) and pressure (0.1 to 260 MPa, at 324 K) by measuring the ^17/O-FT-NMR line-widths of the resonance from coordinated water at 27.11 and 48.78 MHz. The following exchange parameters were obtained: k²⁹⁸_ex = (560 ± 40) s^?1, ΔH* = (49.5 ± 1.9) kJ mol^?1, ΔS* = – (26 ± 6) J K^?1 mol^?1 and ΔV* = – (2.2 ± 0.2) cm³ mol^?1. The values refere to an aqueous perchlorate medium with an ionic strength between 2.0 and 2.6 m and a perchloric-acid concentration between 0.8 and 1.7 m, and are interpreted in terms of an associative (a) activation for the exchange. The exchange rate for Pd(H₂O)²₄⁺ is 1.4 × 10⁶ times faster than for Pt(H₂O)²₄⁺ at 298 K. A comparison with reactions between other nucleophiles and Pd(H₂O)²₄⁺ is also made.     

Cation-Induced dimerization of nickel(II), platinum(II), and palladium(II) meso-tetra(benzo-15-crown-5)porphyrinates

Cation-induced dimerization of nickel(II), platinum(II), and palladium(II) meso-tetra(benzo-15-crown-5)porphyrinates (Ni(II)TCP, Pd(II)TCP, and Pt(II)TCP) on treatment with potassium thiocyanate in a chloroform-methanol solution has been studied by electronic absorption spectroscopy. The formation of [{MTCP}₂(K⁺)₄](SCN^?)₄ in solution induces a hypsochromic shift of the Soret band and a bathochromic shift of the β-band with respect to their positions in the spectrum of MTCP. The equilibrium constants (K) for the 2MTCP + 4K⁺ = [{MTCP}₂(K⁺)₄] processes at 20°C are determined to be as follows: log K _Ni(II)TCP = 27.31 ± 1.67, logK _Pd(II)TCP = 27.16 ± 1.43, and logK _Pt(II)TCP = 26.15 ± 1.56.     

Thermal Study of [Pd(2-Phpy)Cl(L)] Complexes (L=pyridines and amines)

The complex [Pd(2-Phpy)(μ-Cl)]₂ reacts with pyridines (L=pyridine, α-picoline and γ-picoline), amines (L=isopropylamine, tert-butylamine) and ammonia to form the corresponding ortho-palladatedderivatives [Pd(2-Phpy)ClL]. The compounds have been characterized by C, H and Nanalyses and spectroscopic methods (IR and ¹H and ¹³C NMR).TG, DTG and DSC studies of the complexes were carried out in dynamic nitrogen atmosphere. From DSC analyses the heats of decomposition were calculated. The kinetics ofthe first step of thermal decomposition were evaluated from TG data by isothermal methods for L=pyridine and isopropylamine. The activation energies obtained are in the range 90–100 kJ mol^-1. The best fitting for data was observed for R2 and A1.5 kinetic models. This revised version was published online in August 2006 with corrections to the Cover Date.