基于Hilbert-Huang变换的数字全息图中的零级项抑制

针对数字全息图中的零级项问题,提出一种用Hilbert-Huang变换对零级项进行抑制的方法.首先将二维数字全息图数据展开为一维数据,然后用Hilbert-Huang变换进行经验模型分解,得到第一层的本征模函数,该函数包含了全息图的高频分量,继续分解,得到第二层的本征模函数,该函数包含了全息图的直流分量.实验结果证明,将第一层的本征模函数进行再现,即为零级项得到有效抑制的共轭像,第二层的本征模函数为零级项.该方法只需在空域中进行一次经验模型分解就可有效抑制零级项,较好地保存了原物波信息,在计算速度上具有明显优势.     

通过保留相位进行全息图信息压缩的方法

从全息图的特点出发,研究了全息图的记录和再现原理,提出了一种对离轴菲涅耳全息图信息压缩的方法。对全息图进行傅里叶变换,滤除零级噪声及物光波的共轭波前,仅仅保留物光波的相位信息,而后以采用较低的采样频率对全息图重新抽样,从而大大减少了数字全息图的信息冗余。压缩后的全息图也可以获得良好像质的再现像。理论和实验均证明了该方法的可行性,为全息图的信息存贮与传输提供一条新的途径。     

复数滤波器在数字全息图处理中的应用

数字全息图在微电路检测、粒度分析、透明场测量等小孔径、小视场对象测量和细胞观测等显微测量方面有着广泛的应用前景。根据离轴数字全息图的频谱特点,提出采用复数滤波器,利用计算机及相关算法对离轴数字全息图进行滤波,消除其零级及共轭像,同时可以得到全息图的相位分布。讨论了复数滤波器的设计方法,给出了实验结果。为数字全息图的压缩、再现和相息图制作提供了方便。     

基于有限脉冲响应滤波器的数字全息零级像消除

针对数字全息中零级像的存在影响数字再现像的质量,分析数字全息图的记录、再现原理及频谱特性,提出了一种利用有限脉冲响应滤波器消除全息图数字再现中零级像的方法.该方法只需记录一幅数字全息图,不需要相移器材或其他辅助设备,直接利用数字图像处理对数字全息图在空域进行预处理,消除全息再现时的零级像干扰.对比了数字模拟和实验拍摄到的全息图在应用有限脉冲响应滤波器消除零级像前后的再现结果,表明该方法可消除零级衍射像,改善重建像质量,并且算法简单.     

数字全息周期像的产生机理及在抑制零级衍射上的应用

在数字全息成像中, 利用CCD的RGB模式采样全息图时, 全息重构像会出现特定的周期性分布. 本文从理论和实验上详细研究了这种周期像产生的机理、分布特性和应用. 研究结果显示, 由于CCD的光谱滤镜会使全息图的RGB三个单色采样阵列出现部分像素信号的缺失, 因此, 需要通过特定的demosaicing数学算法对缺失的像素信号进行重建以形成完整的单色采样阵列, 这是数字全息再现像周期分布产生的根源. 而基于demosaicing算法的采样阵列重建会在全息图频谱中引入调制函数, 导致物体再现像和零级衍射斑的周期分布差异. 本文揭示了全息图的RGB采样、demosaicing算法与全息重构像周期性之间的内在关联. 最后, 讨论了结合空间移位和图像形态学技术, 利用重构像的周期性抑制零级衍射斑的应用. 所有理论与实验研究结果完全一致. 关键词： 数字全息 图像周期性 零级斑抑制     

一种菲涅尔全息图的快速算法

通过分析菲涅尔全息图计算模型,发现大量的平方运算和三角函数运算是计算速度的瓶颈,提出了一种菲涅尔全息图的快速计算方法.根据菲涅尔全息图的数学模型,利用三角函数的和差化积公式,将全息图的数学模型变换为由仅与水平或垂直方向有关的独立分量,通过四则运算来表示.在菲涅尔全息图的计算中,用少量的三角函数、平方运算和大量的四则运算代替原来大量的三角函数和平方运算,减少了全息图的运算量.实验表明,采用该算法后全息图的计算速度提高了9倍以上.     

菲涅耳数字全息成像系统的脉冲响应分析

数字全息成像由CCD记录数字全息图后经过计算机数值重建物光波场,这个过程从傅里叶变换角度看等同于数字全息图的频谱分析。讨论了数字成像系统的脉冲响应函数,并分别推导了其实像、虚像、零级像在平面波和球面波照射下的波前复振幅分布。结果表明,实像和虚像是移位的夫琅和费衍射分布,而零级像是CCD光瞳的菲涅耳衍射分布,且与参考光波前分布无关。     

压缩态光场平衡零拍探测的位相锁定

平衡零拍探测是测量量子光场的重要方法之一. 通过对相位灵敏光学参量放大器注入的信号进行位相调制, 然后利用平衡零拍探测系统测量光学参量放大器输出的压缩光. 将相位灵敏光学参量分别运转在参量放大和参量缩小, 通过观察噪声谱中的调制信号就可确定测量的量子光场是正交振幅或位相分量. 通过解调位相调制信号可获得误差信号, 实现锁定平衡零拍探测系统本底光与待测光场相对位相为零(对应于待测光场振幅噪声分量). 关键词： 平衡零拍探测 位相锁定     

三维物体多重菲涅耳计算全息水印与无干扰可控重建方法

提出了一种基于三维物体的多重菲涅耳计算全息水印方法.将水印信号作为虚拟三维物体的层面,首先结合分区复用层析法和菲涅耳双随机相位编码方法产生复噪声形式的水印信号;然后对水印信号的频谱作共轭对称处理实现实值编码;为减小对宿主全息图数字重建的影响,将水印信号的频谱设置于对宿主数字重建影响小的频谱非感兴趣区域;编码后的信号以一定强度叠加于宿主全息图,水印信号恢复无需原始宿主全息图信息,可实现盲提取,对宿主全息图重建像面的二维码可扫描识别.仿真测试结果表明,所提出的方法具有较好的透明性和稳健性,在宿主全息图遭受滤波、JPEG(联合图像专家小组)压缩、高斯噪声、剪切、旋转等各种攻击的情况下,不论对宿主还是水印信号仍具有良好的数字重建质量,对重建像面的二维码仍可扫描识别;而重建像面水印信号的无干扰可控重建后处理操作解决了不同层面水印信号之间的衍射干扰问题,提高了水印信号的重建质量.虚拟光学手段的应用丰富了水印信号设计方法并提升了算法的安全性.     

灰度调整与数字全息图像质的关系

如何在有限的灰度级别下输出高质量全息图是人们关注的问题之一,文章从数字全息图(计算机制全息图)的灰度直方图出发,研究灰度调整对全息图再现像质的影响.首先通过理论推导研究了压缩计算机制全息图中占比例少的灰度,展宽占比例多的灰度后全息图衍射效率的变化,发现处理后的计算机制全息图经灰度压缩的阈值越大,衍射效率越高.然后研究了...     

Complex-wave retrieval based on blind signal separation

In the process of the reconstruction of digital holography, the traditional methods of diffraction and filtration are commonly adopted to recover the original complex-wave signal. Influenced by twin-image and zero-order terms, the above-mentioned methods, however, either limit the field of vision or result in the loss of the amplitude and phase. A new method for complex-wave retrieval is presented, which is based on blind signal separation. Three frames of holograms are captured by a charge coupled device (CCD)camera to form an observation signal. The term containing only amplitude and phase of complex-wave is separated, by means of independent component analysis, from the observation signal, which effectively eliminates the zero-order term. Finally, the complex-wave retrieval of pure phase wavefront is achieved.Experimental results show that this method can better recover the amplitude and phase of the original complex-wave even when there is a frequency spectrum mixture in the hologram.     

Improved approach for target detection and recognition on optoelectronic hybrid joint transform correlator

A conventional joint transform correlator (JTC) often generates large correlation sidelobes as well as a large correlation peak width, strong zero-order peak, and low diffraction efficiency in target detection and recognition, which make the detection ability of JTC lower. To conquer these difficulties, firstly, a joint power spectrum (JPS) subtraction technique was proposed in Fourier plane, where power spectrum of reference image and power spectrum of object image are subtracted from the JPS before inverse Fourier-transform operation, it is evident that the improved JPS removes the zero-order term. Secondly, a fringe-adjusted filter (FAF) was presented to restrain sidelobes and noises. The revised JPS is multiplied by a FAF before the inverse Fourier-transform operation to obtain the cross-correlation peak. Computer simulations showed the improved method can markedly eliminate zero-order diffraction and effectively control the sidelobes and noises compared to traditional JTC, and then enhance the detection ability for JTC. Experimental results presented the sharp correlation peak and also demonstrated this approach effectiveness.     

Efficient interface conditions for the semi-vectorial finite-difference beam propagation method

Efficient interface conditions (EICs) are derived for the propagation equation using the slowly varying envelope approximation for the dominant electric field component. At the interface between two different media, the two lateral second derivatives in the discretized propagation equation are adapted such that the discretized modal field equation is correct up to second order in the lateral grid spacing. Since the error term is then of the order of the lateral grid spacing, our EICs are first-order EICs. These interface conditions are compared with well-known zero-order EICs derived by Stern and Kim and Ramaswamy. It is shown that the first-order EICs yield faster convergence to the exact effective index value as the lateral grid spacing is decreased than do the zero-order EICs. It turns out that our EICs are very much like those derived by Vassallo. Using essentially the same method, he derived EICs of second and first order for the field component respectively parallel and perpendicular, to the interface. Hence the accuracy of his EICs is one order higher for the field component parallel to the interface, although it introduces an extra asymmetry in the propagation matrix.     

基于零级贝塞尔光束干涉产生的局域空心光束

通过对由两个零级贝塞尔光束相干叠加形成的三维衍射光场的理论分析和计算机模拟,发现当双零级贝塞尔光束的有关参量满足一定条件时,会在光轴上形成一系列高质量的局域空心光束。在此基础上,进一步分析了这种阵列局域空心光束的大小、阵列周期及局域空心光束的质量与双零级贝塞尔光束和光路参量的定量关系。推导出双零级贝塞尔光束叠加时在中心暗斑位置达到完全干涉相消的条件是通过两个环缝的能量要相同,以及产生最佳局域空心光束的内外环缝光源半径的比值为0.465。该研究为进一步设计制备基于双零级贝塞尔光束干涉实现阵列局域空心光束的新型衍射光学元件提供了理论依据和设计参量。     

Digital holographic image fusion for a larger size object using compressive sensing

Digital holographic imaging fusion for a larger size object using compressive sensing is proposed. In this method, the high frequency component of the digital hologram under discrete wavelet transform is represented sparsely by using compressive sensing so that the data redundancy of digital holographic recording can be resolved validly, the low frequency component is retained totally to ensure the image quality, and multiple reconstructed images with different clear parts corresponding to a laser spot size are fused to realize the high quality reconstructed image of a larger size object. In addition, a filter combing high-pass and low-pass filters is designed to remove the zero-order term from a digital hologram effectively. The digital holographic experimental setup based on off-axis Fresnel digital holography was constructed. The feasible and comparative experiments were carried out. The fused image was evaluated by using the Tamura texture features. The experimental results demonstrated that the proposed method can improve the processing efficiency and visual characteristics of the fused image and enlarge the size of the measured object effectively.     

A three-spectrum method for accurate calibration of bi-plate zero-order retarder

A new spectroscopic method is proposed for the characterization of optical zero-order retarders. It is demonstrated that the retardance as well as the variation of the effective fast axis of a bi-plate zero-order quarter retarder （633 nm） can be obtained with high accuracy in a broadband wavelength range by taking spectra at only three independent angular orientations of the retarder. The calibration results excellently agree with theoretical models, indicating the new method could be used as a simple and reliable way for efficient self-spectral-calibration of optical zero-order retarders.     

用改进的Fienup迭代算法进行数字全息重建

数字全息成像中往往包括再现像、共轭像和零级项,再现像的分离是常见而又难以彻底解决的问题。提出一种新的全息图重建算法,即利用相干衍射成像（CDI）中的迭代方法处理数字全息图,实现仅有一个实像的再现结果,从而彻底解决该问题。该方法包括两个步骤：首先通过CCD分别测量样品单独存在、样品和参考光同时存在以及参考光的远场衍射分布;然后通过计算机进行迭代运算。由于干涉光的存在,该算法比传统的CDI算法有更快的收敛速度和重建质量。同时进行了数值模拟验证并对生物切片进行了物像重建。     

一种液晶相位调制特性的测量方法

提出一种基于衍射光栅的液晶相位调制特性测量方法.该方法利用液晶构建相位分别为0和φ的二值光栅,通过傅里叶光学的方法推导衍射光栅第0级衍射光斑光强和调制相位φ之间的关系,然后实测光强和液晶驱动电压之间的对应关系来得到相位和液晶驱动电压之间的对应关系,即液晶相位光栅的相位调制特性.最后利用测量相位调制特性结果构建液晶相控阵,用光束偏转误差验证调制特性测量结果,相位测量误差小于1×10~(-3)rad.     

用基于磁场的改进型有限差分法分析光波导的全矢量本征模

提出一种改进的有限差分法,用以求解全矢量磁场波方程,分析光波导承载的全矢量本征模.离散交叉项时,采用与波导结构无关的六点差分格式,考虑磁场分量的导数在芯包分界处的不连续性,比传统四点差分格式有更高的计算精度.分析阶跃型光纤、矩形和脊形光波导的全矢量本征模问题,给出全矢量基模的磁场分布及其归一化传播常数,揭示全矢量本征模的混合特性,所得结果与解析法、高精度模横向谐振法的结果吻合,验证了方法的收敛性与计算精度.