Comparison of the elongational behavior of various polyolefins in uniaxial and equibiaxial flows

For processing operations with a pronounced elongational component, it was found that the uniformity of extruded items is improved by the presence of strain hardening usually measured in uniaxial elongation. Many processing operations such as foaming, film blowing, and blow molding are dominated by biaxial deformations, however, and therefore, the question arises how strain hardening in uniaxial and biaxial deformation compares. Besides a linear and long-chain branched PP, one classical LDPE, an HDPE pipe extrusion grade with a bimodal MMD, and a LCB-mPE were also characterized. For the measurements in uniaxial elongation the Münstedt tensile rheometer (MTR) and the ARES-EVF were used, while the lubricated flow method was applied for equibiaxial deformation. It was found that the strain hardening in uniaxial elongation is more pronounced. The dependence of strain hardening on strain rate is qualitatively the same in both modes. In the range of strain rates, the chosen long-chain branched LDPE and PP exhibit a strain hardening, which is approximately independent of the elongational rates applied, whereas for the HDPE it becomes smaller with increasing rate.

Simultaneous measurements of velocity and stress distributions in polyisobutylenes using laser-Doppler velocimetry and flow induced birefringence

An experimental device was set up for the synchronous measurement of velocities and stresses in polyisobutylenes using laser-Doppler velocimetry (LDV) and the two-colour flow-induced birefringence method (FIB). The materials investigated are three low molecular polyisobutylenes. Velocity (LDV) and stress (FIB) measurements are performed in the flow entrance region and inside a slit die with a contraction ratio of 1:10. The behaviour of the polyisobutylenes is Newtonian under the flow conditions applied. Therefore, the stresses inside the fluids can be calculated and compared to the stresses experimentally determined. A good agreement in shear and elongational flows was found between the calculated (LDV) and directly measured stresses (FIB). This result demonstrates the applicability of the experimental setup as an optical rheometer that can preferentially be used to measure elongational properties of low viscous fluids.

Rheological behaviour and molecular structure of long-chain branched semifluorinated thermoplastics

The long-chain branched thermoplastic tetrafluoroethylene–hexafluoropropylene–vinylidenefluoride terpolymers (LCB THV) investigated in this paper are new polymers with a unique combination of properties like a high stability against aging or weathering and a very good chemical resistance. But not much is known about the rheological behaviour of the LCB THV, yet. In this paper, non-linear rheological properties like shear thinning and strain hardening are studied. Two different types of the THV with different contents of comonomers and, therefore, different melting points are examined. The THV with the higher melting point is insoluble. The other with the lower melting temperature is soluble and, therefore, was characterised by size exclusion chromatography coupled with light scattering with respect to its molecular structure. The results of the rheological measurements show a pronounced shear-thinning and strain-hardening behaviour for the long-chain branched materials. Both properties are of great importance for processing operations governed by shear and elongational flows.

Microscale Synthetic Schlieren

We develop the axisymmetric Synthetic Schlieren technique to study the wake of a microscale sphere settling through a density stratification. A video-microscope was used to magnify and image apparent displacements of a micron-sized random-dot pattern. Due to the nature of the wake, density gradient perturbations in the horizontal greatly exceed those in the vertical, requiring modification of previously developed axisymmetric techniques. We present results for 780 and 383 μm spheres, and describe the limiting role of noise in the system for a 157 μm sphere. This technique can be instrumental in understanding a range of ecological and environmental oceanic processes on the microscale.

---

Measurement of the aerodynamic forces on a small particle attached to a wall

Using operating principles similar to that applied in atomic force microscopes, we have developed a novel measuring method to study the aerodynamic forces, in particular the lift and drag force, acting on a small particle attached to a wall and immersed in a linear shear flow. Results thus far have shown that the system is capable of measuring both the minute aerodynamic lift and drag forces that a particle experiences as a result of the flow.C. Muthanna has also published under the name C. M. Kolera

---

Turbulence measurements in a swirling pipe flow

This paper reports laser-Doppler measurements of the mean flow and turbulence stresses in a swirling pipe flow. Experiments were carried out under well-controlled laboratory conditions in a refractive index-matched pipe flow facility. The results show pronounced asymmetry in mean and fluctuating quantities during the downstream decay of the swirl. Experimental data reveal that the swirl significantly modifies the anisotropy of turbulence and that it can induce explosive growth of the turbulent kinetic energy during its decay. Anisotropy invariant mapping of the turbulent stresses shows that the additional flow deformation imposed by initially strong swirling motion forces turbulence in the core region to tend towards the isotropic two-component state. When turbulence reaches this limiting state it induces rapid production of turbulent kinetic energy during the swirl decay.

---

Variational optical flow estimation for particle image velocimetry

We introduce a novel class of algorithms for evaluating PIV image pairs. The mathematical basis is a continuous variational formulation for globally estimating the optical flow vector fields over the whole image. This class of approaches has been known in the field of image processing and computer vision for more than two decades but apparently has not been applied to PIV image pairs so far. We pay particular attention to a multi-scale representation of the image data so as to cope with the quite specific signal structure of particle image pairs. The experimental evaluation shows that a prototypical variational approach competes in noisy real-world scenarios with three alternative approaches especially designed for PIV-sequence evaluation. We outline the potential of the variational method for further developments.The publications of the CVGPR Group are listed under .

---

The dynamics of a boiling bubble before and after detachment

An overview is given of prediction methods for motion and deformation of a bubble that is created by boiling at a wall, at times before and after detachment, with a focus on added mass forces in the vicinity of the wall. The possibility to apply added mass coefficients derived in potential flows also to flows with vorticity is examined. An introduction to Lagrangian methods is given. Added mass tensors are derived for deforming bubbles at and away from a plane wall. Expressions for induced hydrodynamic lift forces are given, and validation experiments are briefly discussed.

---

An application of Gappy POD

An iterative procedure, based on the proper orthogonal decomposition (POD), first proposed by Everson and Sirovich (J Opt Soc Am A 12(8):1657–1664, 1995) is applied to marred particle image velocimetry (PIV) data of shallow rectangular cavity flow at Mach 0.19, 0.28, 0.38, and 0.55. The procedure estimates the POD modes while simultaneously estimating the missing vectors in the PIV data. The results demonstrate that the absolute difference between the repaired vectors and the original PIV data approaches the experimental uncertainty as the number of included POD modes is increased. The estimation of the dominant POD modes is also shown to converge by examining the subspace spanned by the POD eigenfunctions.

---

A random synthetic jet array driven turbulence tank

We measure the flow above an array of randomly driven, upward-facing synthetic jets used to generate turbulence beneath a free surface. Compared to grid stirred tanks (GSTs), this system offers smaller mean flows at equivalent turbulent Reynolds numbers with fewer moving parts.

---

Two- and three-dimensional flows in nearly rectangular cavities driven by collinear motion of two facing walls

Two- and three-dimensional flows in nearly cuboidal cavities are investigated experimentally. A tight cavity is formed in the gap between two long and parallel cylinders of large radii by adding rigid top, bottom, and end walls. The cross-section perpendicular to the axes of the cylinders is nearly rectangular with aspect ratio Γ. The axial aspect ratio Λ > 10 is large to suppress end-wall effects. The fluid motion is driven by independent and steady rotation of the cylinders about their axes which defines two Reynolds numbers Re _1,2. Stability boundaries of the nearly two-dimensional steady flow have been determined as functions of Re _1,2 for Γ = 0.76 and Γ = 1. Up to six different three-dimensional supercritical modes have been identified. The critical thresholds for the onset of most of the three-dimensional modes, three of which have been observed for the first time, agree well with corresponding linear-stability calculations. Particular attention is paid to the flow for Γ = 1 under symmetric and parallel wall motion. In that case the basic flow consists of two mirror symmetric counter-rotating parallel vortices. They become modulated in span-wise direction as the driving increases. Detailed LDV measurements of the supercritical three-dimensional velocity field and the bifurcation show an excellent agreement with numerical simulations.

---

Unsteady air–water flow measurements in sudden open channel flows

Measurements of air–water flow properties are reasonably simple in steady flows, but not so in unsteady flows. Some studies investigated periodic flows in which instantaneous data were averaged over several cycles. During the present work, new unsteady air–water flow measurements were performed in sudden open channel flow surges. Unsteady air–water flow measurements were performed in the wave front with an array of resistivity probes. The results demonstrated quantitatively strong aeration of the leading edge in terms of void fractions, bubble count rates and specific interface areas. Experimental results highlighted that this strongly aerated region was relatively short: i.e. typically 0.3 to 0.5 m long. Measurements of air and water chord sizes highlighted a wide range of bubble and droplet sizes. Time-variations of air–water flow structure were observed.

---

Transient elongational viscosities of aqueous polyacrylamide solutions measured with an optical rheometer

An anionic polyacrylamide solution was characterized in elongational flow by combining laser-Doppler velocimetry to determine the strain rate in the flow direction and the two-color flow-induced birefringence method to measure the first normal stress difference along the axial centerline of a hyperbolic die. The elongational rate was constant along the axial centerline of the planar hyperbolic die as long as vortices at the die entrance did not occur. The transient elongational viscosity μ ⁺ was determined as a function of the elongational rate. The parameters varied are the Hencky strain rate and the polymer concentration. μ ⁺ showed a pronounced increase over the linear viscoelastic behavior above critical Hencky strains of 1.2 to 1.5; that is, a significant strain hardening could be observed for polyacrylamide solutions. This strain hardening is stronger the higher the elongational rate. A slight enhancement of strain hardening was found by increasing the concentration from 0.5 to 1 g/l. The stress optical coefficient was determined as 1.8 × 10⁻⁷ Pa⁻¹ (0.5 g/l) and 1.2 × 10⁻⁷ Pa⁻¹ (1 g/l).

Recent experimental probes of shear banding

Recent experimental techniques used to investigate shear banding are reviewed. After recalling the rheological signature of shear-banded flows, we summarize the various tools for measuring locally the microstructure and the velocity field under shear. Local velocity measurements using dynamic light scattering and ultrasound are emphasized. A few results are extracted from current works to illustrate open questions and directions for future research.

Comment on the Clauser chart method for determining the friction velocity

A known difficulty with using the Clauser chart method to determine the friction velocity in wall bounded flows is that it assumes, a priori, a logarithmic law for the mean velocity profile. Using both experimental and DNS data in the literature, this note explicitly shows how friction velocities obtained using the Clauser chart method can potentially mask subtle Reynolds-number-dependent behavior.

---

Thrust performance of unsteady propulsors using a novel measurement system,and corresponding wake patterns

An apparatus is described for the measurement of unsteady thrust and propulsive efficiency produced by biologically inspired oscillating hydrodynamic propulsors. Force measurement is achieved using a strain-gauge-based force transducer, augmented with a lever to amplify or attenuate the applied force and control the measurement sensitivity and natural frequency of vibration. The lever can be used to tune the system to a specific application and it is shown that, using the lever, the stiffness can be made to increase more rapidly than the measurement sensitivity decreases. Efficiency is computed from measurements of the time-averaged power imparted to the fluid. The apparatus is applied to two different propulsors, demonstrating the versatility of the system; wake visualizations are examined, which provide insight into the physical mechanisms of efficient propulsion.

---

Simultaneous stress and birefringence measurements during uniaxial elongation of polystyrene melts with narrow molecular weight distribution

Tensile stress and flow-induced birefringence have been measured during uniaxial elongation at a constant strain rate of two polystyrene melts with narrow molecular weight distribution. For both melts, the stress- optical rule (SOR) is found to be fulfilled upto a critical stress of 2.7 MPa, independent of strain rate and temperature. Estimation of the Rouse times of the melts, from both the zero-shear viscosity and the dynamic-shear moduli at high frequency, shows that the violation of the SOR occurs when the strain rate multiplied by the Rouse time of the melt exceeds by approximately 3. The presented results indicate that in contrast to current predictions of molecular theories, the regime of extensional thinning observed by Bach et al. (2003) extends well beyond the onset of failure of the SOR, and therefore the onset of chain stretch in the non-Gaussian regime.

Analysis of velocity interpolation schemes for image deformation methods in PIV

The spatial resolution of PIV can be increased significantly by using an image deformation method (IDM) and very small grid distance (i.e. the final distance between vectors), therefore, also increasing the processing time. By using an interpolation scheme with a good spectral response, in the dense predictor step of the algorithm, it is possible to increase the grid distance without decreasing the spatial resolution therefore decreasing the total processing time.

---

A model of a subcritical Joule–Thomson cryocooler with condensation inside the recuperator

To develop a tool for predicting of heat and mass transfer in Joule–Thomson cryocoolers working at subcritical pressures, we study a counter flow heat exchanger with condensation by employing the integral method. The effects of inlet pressure and working fluid are predicted. We also show that there is an optimal value of the enthalpy difference along the heat exchanger for which its length is minimal.

---