铁表面银纳米粒子自组装膜及其缓蚀性能研究

应用化学还原法于水溶液中制备银纳米粒子.在十二烷基硫醇的保护下,将银纳米粒子从水相转移到甲苯相,并将处理好的铁电极浸泡在含有十二烷基硫醇保护的银纳米粒子/甲苯溶液中,制得十二烷基硫醇/银纳米粒子自组装混合膜.电化学方法如交流阻抗谱(EIS)、极化曲线等研究该自组装膜在0.5 mol.L-1H2SO4溶液中的缓蚀作用.XPS测试证实该自组装膜十二烷基硫醇和银纳米粒子之存在.     

正、叔十二烷基硫醇在铜表面上自组装膜测试

研究了正、叔十二烷基硫醇在铜表面上的自组装及混合自组装成膜情况,并利用交流阻抗和极化曲线电化学方法测试了正、叔十二烷基硫醇在铜表面上自组装膜及混合自组装膜对铜的耐腐蚀性,考察了正十二烷基硫醇自组装膜质量与正十二烷基硫醇溶液的浓度及组装时间的关系。研究结果显示,混合自组装膜的质量及其对铜的耐腐蚀性比仅组装正或叔十二烷基硫醇均有很大的提高。     

图案化自组装膜导向的电沉积

通过图案化自组装膜导向的电沉积制备了聚吡咯(PPy)微结构. 由微接触印刷方法制备图案化自组装膜并作为电沉积的模板. 研究发现, 自组装膜在导向电沉积中在不同的基底上具有不同的作用: 在十二烷基硫醇(DDT)、十八烷基硫醇(ODT)修饰的金基底上和十八烷基三氯硅烷(OTS)修饰的铟锡氧化物玻璃上(ITO), 电沉积主要发生在自组装膜未修饰区, 而在半导体单晶硅表面, PPy沉积在OTS修饰区, 是基底表面的导电性及PPy与基底表面基团相容性共同作用的结果.     

硫醇自组装膜对金电极上吡咯电化学聚合的影响

用电化学聚合法在多种烷基硫醇自组装膜修饰金电极上制备了聚吡咯.通过计时安培法、循环伏安法和交流阻抗技术研究了自组装膜的烷基链长和端基功能团对吡咯聚合过程和性质的影响.当自组装膜较完美时,聚吡咯沉积在自组装膜表面;而当自组装膜有一定缺陷时,吡咯在针孔处成核,然后继续生长并完全覆盖在自组装膜表面.研究结果表明,烷基硫醇的链越短,吡咯聚合越容易;疏水的烷基硫醇自组装膜有利于聚吡咯在电极表面的生长.     

具有超疏水性质的图案化Ag膜

以重氮树脂(DR)/聚丙烯酸(PAA)自组装膜的微图案作为模板, 通过DNA和聚二甲基二烯丙基氯化铵(PDDA)在模板上的层层沉积制备了图案化的DNA膜. 再在其中进行Ag的化学沉积得到图案化的Ag膜. 最后利用低表面能的十二烷基硫醇对Ag膜进行表面修饰, 制备了具有超疏水性质的图案化Ag膜. 其静态接触角达到约168°.     

缓蚀膜电化学行为与微观粘附力特征

采用传统电化学测试技术及原子力显微镜(AFM)力曲线分析法对十二烷基硫醇/金电极以及十二烷基磺酸钠(SDS)/铝电极表面缓蚀吸附膜的吸附行为进行了研究. 结果表明, 随缓蚀剂浓度改变, 电极电化学行为与缓蚀膜的微观粘附力特征呈现出关联性的变化趋势, 表明AFM力曲线技术可成功应用于缓蚀膜吸附行为的研究.     

锆离子改善十烷基磷酸组装膜结构及性能研究

利用烷基磷酸、金属锆离子和不锈钢电极表面的相互作用,通过表面自组装,在304不锈钢电极表面分别修饰了单层和双层烷基磷酸自组装膜,采用接触角和极化曲线对修饰电极进行测量.实验表明,双层烷基磷酸修饰膜具有更佳的耐腐蚀性能.     

硫醇分子链长对氧化还原自组装多层膜电化学行为影响的初步研究(英文)

以烷基硫醇和二茂铁衍生物构建的氧化-还原自组装多层膜为模型体系,研究烷基硫醇分子链长对多层膜电化学行为的影响.实验表明,二茂铁基团和电极之间的电子传递反应速率随两者距离的增加呈现指数级下降的趋势;烷基硫醇分子链长对自组装膜电化学行为的影响于不同情况下表现不同.本实验条件下,当多层膜上的电活性基团与电极比较接近时,长链分子自组装膜呈现较强的电化学响应.而当电极与电活性基团之间的距离较远时,短链烷基硫醇分子自组装膜呈现较强的电化学响应.     

Au纳米粒子在有机溶剂中的电导行为

采用化学方法制备出粒径约10nm的Au纳米粒子,分别用十二、十四和十六烷基硫醇对Au粒子表面进行修饰,再溶入不同有机溶剂中,制备得到Au纳米粒子/氯仿和Au纳米粒子/甲苯溶液.测试了不同溶液的电导率随溶质浓度的变化规律,发现在整个浓度范围内存在一个临界浓度值.当溶质浓度低于临界浓度值时,溶液的电导率随溶质浓度的增加而迅速增加;而当溶质浓度超过临界浓度值时,溶液电导率的增加缓慢.在本文测试的浓度范围内,当Au纳米粒子分别被十二、十四和十六烷基硫醇修饰时,Au纳米粒子/氯仿溶液的临界浓度值分别约为11.22,7.96和5.47g/L.在相同浓度下,Au纳米粒子外面包裹的烷基硫醇的链长越短,其溶液的电导率越大.在整个浓度范围内,Au纳米粒子/氯仿溶液的电导率均高于Au纳米粒子/甲苯溶液的电导率.     

表面活性剂对硫醇单层膜修饰金电极电化学行为的影响

利用自组装方法在金电极表面制备成硫醇单层膜, 循环伏安和交流阻抗实验表明硫醇单层膜与表面活性剂十六烷基三甲基溴化胺作用后, 其电化学行为发生变化, 对于带有不同电荷的探针分子, 表现出一定的选择性响应. 即使是带有相同电荷的探针分子, 由于与表面活性剂的作用方式不同, 也使它们通过硫醇单层膜在电极表面产生电化学响应的程度完全不同.     

The study of self-assembled films of triazole on iron electrodes using electrochemical methods,XPS, SEM and molecular simulation

3-Alkyl-4-amino-5-mercapto-1,2,4-triazole (AAMT) has been evaluated as corrosion inhibition for iron in 0.1 M H₂SO₄ when the films of AAMT were self-assembled on the surface of iron. The films of AAMT inhibitor were characterized by electrochemical impedance spectroscopy, electrochemical polarization curves Results revealed that AAMT performed excellently as a corrosion inhibitor for iron in H₂SO₄ solution. Surface analysis was carried out using X-ray photoelectron spectroscopy and scanning electron microscope. The mechanism of adsorption was discussed using molecular simulation.     

Development of a new C14 monolithic silica column containing embedded polar groups for pressurized capillary electrochromatography

Monolithic columns have been prepared with a novel bonded silica stationary phase, tetradecylamine bonded silica (TDAS), and used in pressurized capillary electrochromatography (pCEC). The monolithic silica column matrix was prepared by a sol-gel process and then chemically modified with the spacer (3-glycidoxypropyl)trimethoxysilane and tetradecylamine. The introduced embedded polar amine groups dominated the charge on the surface of the monolithic stationary phase and generated an EOF from cathode to anode under acidic conditions. The tetradecyl hydrophobic chains in TDAS provide chromatographic interactions. The chromatographic characteristics of the prepared monolithic column were studied. Some aromatic compounds including alkylbenzenes, aromatic hydrocarbons, phenols, and anilines were successfully separated on the TDAS monolithic column in pCEC mode. As expected, the TDAS monolithic stationary phases exhibit typical reversed-phase electrochromatographic behavior toward neutral solutes due to the introduced tetradecyl groups. Hydrophobic as well as electrophoretic migration processes within the monoliths were observed in the separation of basic anilines. Symmetrical peaks can be obtained for anilines because the embedded polar amine groups on the surface can effectively shield the adsorption of positively charged analytes onto the stationary phase.     

基于铁薄膜的表面等离子体耦合定向荧光研究

本文报道了以纳米铁膜为基底的SPCDF检测方法. 以荧光素和卟啉为例, 探讨了SPCDF信号的特性, 在固定角度下检测了荧光素-卟啉双荧光团体系的SPCDF信号, 并应用于全血样品的分析.     

分子结构对硫脲类化合物在铜表面自组装能力的影响

利用电化学阻抗谱和极化曲线研究了硫脲、烯丙基硫脲、苯基硫脲在金属铜表面上的自组装膜的质量和缓蚀效率, 并通过量子化学计算进一步研究了各种分子和金属铜的相互作用. 结果表明硫脲类分子在金属铜表面上的成膜能力顺序为: 苯基硫脲＞烯丙基硫脲＞硫脲, 并揭示了分子结构对硫脲类化合物在金属铜表面自组装影响的本质, 为进一步寻找和制备优良的缓蚀功能自组装膜提供理论依据.     

氧化铁薄膜的水热合成及其光电转换性能

通过水热方法在掺杂氟的SnO2(FTO)导电玻璃上制备了不同形貌的氧化铁薄膜。利用无机铁盐浸渍法在FTO玻璃上进行氧化铁晶种的预处理使得所制备的氧化铁薄膜更致密且均一。研究了表面活性剂对氧化铁晶体形貌的影响。使用十二烷基苯磺酸钠(SDBS)和三嵌段聚合物P123做为形貌导向剂分别得到棒状和四方体形貌的氧化铁薄膜。氧化铁薄膜可调的形貌可能是由于表面活性剂和铁氧团簇的组装或者某些晶面吸附了阴离子而改变了生长速率引起的。同时,研究了其光电性能,具有四面体形貌的氧化铁薄膜可以产生较大的光电流,这是由于其缩短了光生空穴的扩散距离。     

铁、氮共掺杂二氧化钛薄膜的亲水性能

采用溶胶-凝胶法制备了铁掺杂TiO2(Fe-TiO2)薄膜, 将Fe-TiO2薄膜放置氨气气氛中高温处理, 形成铁、氮共掺杂TiO2(Fe/N-TiO2)薄膜. 通过XRD、XPS、SEM、UV-Vis法进行吸收光谱分析及薄膜表面亲水接触角分析, 研究了铁、氮掺杂浓度, 热处理温度, 膜厚等因素对薄膜亲水性能的影响. 结果表明, Fe/N-TiO2(0.5%Fe, 摩尔百分数)显示出更佳的亲水性能, 在可见光下优势尤为明显. 铁掺杂主要作用是降低电子和空穴的复合几率, 氮掺杂可以增强TiO2薄膜在可见光区的吸收, 两种效应相互结合, 共同提高了薄膜在可见光下的亲水性能.     

Adsorption of Polycation and Anionic Surfactant onto Iron Surfaces and the Inhibition of Carbon Dioxide Corrosion

The adsorption process of two polycations (pDADMAC and C‐PAM) with different charge densities has been investigated using the quartz crystal microbalance technique with dissipation monitoring (QCM‐D). The effect of the charge density of the polycation, the NaCl concentration, and the complexation with an anionic surfactant are addressed in this work. X‐ray photoelectron spectroscopy and atomic force microscopy were utilized to analyze the adsorbate with respect to the film coverage and film structure. The corrosion‐inhibiting performance of the films on high‐purity iron in a CO₂ saturated brine, at 25°C, 1 bar CO₂, and pH 4, was investigated by the linear polarization resistance technique. It was found that the polycations adsorbed onto the iron surface, but the corrosion rate of 1 mm yr^?1 was not lowered. However, the polycations formed a complex with an anionic surfactant, and such films showed excellent inhibition performance. Both films, of pDADMAC/SDS and of C‐PAM/SDS, lowered the corrosion rate of iron below 0.01 mm yr^?1. The SDS concentration was below the cmc. It is believed that the SDS adsorbed into the preadsorbed polycation film, forming a complex structure resulting in a hydrophobic and dense film.     

An approach to differentiating between multi‐ and monolayers using MALDI‐TOF MS

Analysis and confirmation of monolayer film thickness on metal oxide surfaces has proven to be challenging. XPS and AFM have been used to investigate the monolayer formation. However, these techniques are difficult to access and/or determine the composition of the organic molecules on the surfaces. Here we demonstrate the ability of MALDI‐TOF to characterize long alkyl chain phosphonic acid molecules in thin films on titanium, iron and stainless steel. These systems are known to be stable, strongly adhered films. The thin films were characterized by IR, AFM, contact angle measurements and the results were confirmed by MALDI‐TOF. Moreover, the MALDI‐TOF was used to differentiate between mono‐ and multilayers on planar surfaces. Copyright © 2007 John Wiley & Sons, Ltd.     

磁性凹凸棒土制备及其脱汞性能研究

对自然界中广泛存在的凹凸棒土(Atp)进行磁改性,通过沉积-沉淀法制备出磁性氧化铁改性的磁性凹凸棒土(MAtp),采用BET、VSM、XRD以及SEM等手段对其理化性质加以分析,并在固定床实验台上进行模拟烟气脱汞性能测试,研究了铁氧化物含量、反应温度和烟气成分对其除汞能力的影响。结果表明,Atp与磁性物质的复合提高了其对Hg~0的脱除能力,并且随铁氧化物含量升高,MAtp脱汞能力逐渐增强;在实验温度区间内,脱汞能力随温度的升高逐渐增强,MAtp对Hg~0以化学吸附为主;O_2、NO的添加有利于Hg~0的脱除,但Hg~0穿透率随浓度变化不显著;SO_2抑制汞的脱除,并且随浓度的增加,其抑制效果更加明显,但是当NO和SO_2共同存在时,NO能明显削弱SO_2对脱汞的抑制作用。