Electrochemical sensing of DNA immobilization and hybridization based on carbon nanotubes/nano zinc oxide/chitosan composite film

A novel electrochemical DNA biosensor based on zinc oxide （ZnO） nanoparticles and multi-walled carbon nanotubes （MWNTs） for DNA immobilization and enhanced hybridization detection is presented. The MWNTs/nano ZnO/chitosan composite film modified glassy carbon electrode （MWNTs/ZnO/CHIT/GCE） was fabricated and DNA probes were immobilized on the electrode surface. The hybridization events were monitored by differential pulse voltammetry （DPV） using methylene blue （MB） as an indicator. The sensor can effectively discriminate different DNA sequences related to PAT gene in the transgenic corn, with a detection limit of 2.8× 10^-12 mol/L of target sequence.     

Surface structure and adsorption properties of multiwalled carbon nanotubes

The pore structure, sorption parameters, and chemical composition of the surface of multiwalled carbon nanotubes synthesized by catalytic pyrolysis were determined. The dependences of the amount of cholic acid adsorbed by the nanotube surface on time, pH, and concentration of an equilibrium solution were studied. Physical adsorption of cholic acid is mainly the outcome of nonspecific interactions between the acid and the surface of the nanotubes. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1712–1715, October, 2006.     

Pyrene-containing polystyrene segmented copolymer from nitroxide mediated polymerization and its application for the noncovalent functionalization of as-prepared multiwalled carbon nanotubes

This study reports simple and convenient procedures for the preparation of a novel surface modifier for multiwalled carbon nanotubes (CNTs) having uniform and controlled structure through controlled “living” free-radical polymerization technique. The technique afforded pyrene functionalized polystyrene block copolymers (PMAS) having controlled molecular weight, molecular weight distribution and length of each block for effective surface modification of CNTs. The modified CNTs exhibited much improved and stable dispersion in toluene. PMAS-CNT/polystyrene composites afforded clearer and more homogeneous films compared to those containing non-modified CNTs. The polystyrene films containing 2 wt% and 5 wt% of PMAS-CNTs showed improved AC conductivities of approximately 10⁻³ and 10⁻² S/cm, respectively, which were 10 ∼ 10⁶ times higher than those of films containing non-modified CNTs. These results demonstrated that PMAS effectively modified the surface of CNTs, which resulted in improved dispersion of CNTs in polystyrene matrices.     

Synthesis and characterization of pyrene bearing amphiphilic miktoarm star polymer and its noncovalent interactions with multiwalled carbon nanotubes

A novel amphiphilic miktoarm star polymer, polystyrene‐poly(ethylene glycol)‐poly(methyl methacrylate), bearing a pyrene group at the end of PS arm (Pyrene‐PS‐PEG‐PMMA) was successfully synthesized via combination of atom transfer radical polymerization and click chemistry. The structure and composition of the amphiphilic miktoarm star polymer were characterized by gel permeation chromatography and ¹H NMR. The functionalization of multiwalled carbon nanotubes (MWCNTs) via “π–π” stacking interactions with pyrene‐PS‐PEG‐PMMA miktoarm star polymer was accomplished and the resulting polymer‐MWCNTs hybrid was analyzed by using ¹H NMR, UV–vis, fluorescence spectroscopy, and thermal gravimetric analysis. The high‐resolution transmission electron microscopy and analytical techniques aforementioned confirmed that the noncovalent functionalization of MWCNT's with the amphiphilic miktoarm star polymer was successfully achieved. The MWCNT/pyrene‐PS‐PEG‐PMMA exhibited significant dispersion stability in common organic solvents such as dimethyl formamide, chloroform, and tetrahydrofuran. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Complementary effects of multiwalled carbon nanotubes and conductive carbon black on polyamide 6

This article introduces a newly innovative idea for preparation of superconductive ternary polymeric composites of polyamide 6 (PA6), conductive carbon black (CCB), and multiwalled carbon nanotubes (MWCNTs) with different weight ratios by a melt‐mixing technique. The complementary effects of CCB and MWCNTs at different compositions on rheological, physical, morphological, thermal, and dynamic mechanical and electrical properties of the ternary composites have been examined systematically. We have used a novel formulation to produce high‐weight fraction ternary polymer composites that show extremely higher conductivity when compared with their corresponding binary polymer composites at the same carbon loading. For example, with an addition of 10 wt % MWCNTs into the CCB/PA6 composite preloaded with 10 wt % CCB, the electrical conductivity of these ternary composites was about 5 S/m, which was 10 times that of the CCB/PA6 binary composite (0.5 S/m) and 125 times that of the MWCNT/PA6 binary composite (0.04 S/m) at 20 wt % carbon loading. The incorporation of the MWCNTs effectively enhanced the thermal stability and crystallization of the PA6 matrix in the CCB/PA6 composites through heterogeneous nucleation. The MWCNTs appeared to significantly affect the mechanical and rheological properties of the PA6 in the CCB/PA6 composites, a way notably dependent on the MWCNT contents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1203–1212, 2010     

Three-dimensional bundle-like multiwalled carbon nanotubes composite for supercapacitor electrode application

Bundle-type mutil-walled carbon nanotubes (MWCNTs) composite electrode is the first investigation and publication for the supercapacitor application. According to the thermogravimetric analysis results, as-synthesized BCNTs are considered as the electrode materials for supercapacitors and electrochemical double-layer capacitor in this study. The Brunauer–Emmett–Teller specific surface area of as-prepared bundled carbon nanotubes (BCNTs) is 95.29 m²/g given to a type III isotherm and H3 hysteresis loops. Slow scanning rates promote and enhance to achieve high C_b because of the superior conductivity of CNT bundles and one side close-layered Ni/Mg/Mo alloy inside the BCNT-based electrode and facile electron diffusivity between electrolyte and electrode. The specific capacitance C_s (1,560 F/g) is nearly equal to the maximum specific capacitance, which the BCNT-based composite electrode can actually be able to charge or fill in. The maximum energy density value is 195 Wh/kg with corresponding power density values of 0.21 kW/kg. Furthermore, the active 3D BCNTs material fabricated electrode enhances to contact the electrolyte directly and decreases the ion diffusion limitation. Electrochemical impedance spectroscopy spectrum summarized as the low-frequency area controls by mass transfer limitation, and the high-frequency area dominates by charge transfer of kinetic control. After 2,000 consecutive cyclic voltammetry sacnings and galvanostatic charge-discharge cycles at a current density of 1.67 A/g performs, the specific capacitance retentions of 3D BCNTs electrodes achieved 128.2 and 77.3%, respectively. Three-dimensional BCNT composite electrodes exhibit good conductivity and low charge transfer resistance, which is beneficial to fast charge transfer between the BCNTs electrode materials and electrolytes.     

The preparation of functionalized single walled carbon nanotubes as high efficiency DNA carriers

The positively charged single walled carbon nanotubes (SWNTs~ ) were prepared by conjugating with-CONH-C_6H_(12)-NH_3~ . The double strand DNA(dsDNA) chains were loaded onto SWNTs~ via the electrostatic interactions.SWNTs~ shows improved loading efficiency (353.5μg/mg) toward dsDNA compared with that of charged free single walled carbon nanotubes (SWNTs) (82.9μg/mg).     

Label-free and sequence-specific DNA detection down to a picomolar level with carbon nanotubes as support for probe DNA

This study describes a simple and label-free electrochemical impedance spectroscopic (EIS) method for sequence-specific detection of DNA by using single-walled carbon nanotubes (SWNTs) as the support for probe DNA. SWNTs are confined onto gold electrodes with mixed self-assembly monolayers of thioethanol and cysteamine. Single-stranded DNA (ssDNA) probe is anchored onto the SWNT support through covalent binding between carboxyl groups at the nanotubes and amino groups at 5′ ends of ssDNA. Hybridization of target DNA with the anchored probe DNA greatly increases the interfacial electron-transfer resistance (R_et) at the double-stranded DNA (dsDNA)-modified electrodes for the redox couple of Fe(CN)₆^3−/4−, which could be used for label-free and sequence-specific DNA detection. EIS results demonstrate that the utilization of SWNTs as the support for probe DNA substantially increases the surface loading of probe DNA onto electrode surface and thus remarkably lowers the detection limit for target DNA. Under the conditions employed here, R_et is linear with the concentration of target DNA within a concentration range from 1 to 10 pM with a detection limit down to 0.8 pM (S/N = 3). This study may offer a novel and label-free electrochemical approach to sensitive sequence-specific DNA detection.     

Chemically bonded multiwalled carbon nanotubes as efficient material for solid phase extraction of some metal ions in food samples

Multiwalled carbon nanotubes chemically functionalized with 2-((3-silylpropylimino) methyl) phenol (SPIMP-MWCNT) and successfully applied for the solid phase extraction (SPE) of some metal ions in food samples. The influences of the analytical parameters including pH, amounts of solid phase, eluent conditions (type, volume and concentrations), sample volume and interference of some metal ions on the recoveries of ions Cu²⁺, Pb²⁺, Fe²⁺, Ni²⁺ and Zn²⁺ ion were investigated. The metal ions retained on SPIMP-MWCNT was eluted using 6?mL of 4?mol?L^?1 HNO₃ solution and their content was determined by flame atomic absorption spectrometry (FAAS) with recoveries more than 95% and relative standard deviations (n?=?5) between 2.4–3.4% for both reproducibility and repeatability. The detection limit of this metal ions was between 1.0–2.6?ng?mL^?1 (3S _b , n?=?10) and their preconcentration factor was 100, while their loading capacity was above 32.9?mg?g^?1 of SPIMP-MWCNT. The proposed method was successfully applied for the preconcentration and determination of analytes in different samples.     

Novel UV initiator for functionalization of multiwalled carbon nanotubes by atom transfer radical polymerization applied on two different grades of nanotubes

A novel nonoxidative method for preparation of functionalized multiwalled carbon nanotubes (MWCNT) has been developed based on a UV sensitive initiator for atom transfer radical polymerization (ATRP). The method has been investigated with respect to ligands and polymerization time for the preparation of polystyrene functionalized MWCNT. It was found that pentamethyldiethylenetriamine (PMDETA) gave superior results with higher loading in shorter polymerization time. A comparative study of the method applied on two different grades of nonoxidized MWCNT has been performed, illustrating large differences in reactivity and polymer loading, underlining the importance of the choice of MWCNT starting material. In addition to styrene, also poly(ethylene glycol) methacrylate (PEGMA) was shown to polymerize from the surface of the MWCNT. Finally, initial results from composites of polystyrene or polyphenylenesulfide are presented. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Conjugated polymer covalently modified multiwalled carbon nanotubes for optical limiting

A new soluble multiwalled carbon nanotubes (MWNTs) covalently functionalized with conjugated polymer PCBF, in which the wt % of MWNTs is approximately calculated as 7.3%, and the average thickness of PCBF covalently grafted onto MWNTs is 10.4 nm, was synthesized by an amidation reaction. In contrast to the starting polymer PCBF‐NH₂, grafting of PCBF onto MWNTs led to a 0.3 eV red‐shift of the N1s XPS peak at 399.7 eV assigning to N in the unreacted NH₂moieties in the resulting copolymer structure and an appearance of new peak at 402 eV corresponding to N bound to the carbonyl C (i.e., NH? C?O). Unlike PCBF‐NH₂, which only displayed a weak optical limiting response at 532 nm, Z‐scan for MWNT‐PCBF exhibited a much broader reduction in transmission and a scattering accompanying on the focus of the lens at both 532 and 1064 nm, indicating a prominent broadband optical limiting response. The thermally induced nonlinear scattering is responsible for the optical limiting. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

多壁碳纳米管表面L-组氨酸手性印迹聚合材料的制备及性能表征

通过酰胺化反应在多壁碳纳米管（MWNTs）表面接枝双键,以L-组氨酸（L-His）为模板,甲基丙烯酸（MAA）为功能单体,乙二醇二甲基丙烯酸酯（EGDMA）为交联剂,偶氮二异丁腈（AIBN）为引发剂,利用表面印迹技术,在MWNTs表面制备印迹聚合物（MWNTs-MIPs）．采用红外光谱,扫描电子显微镜和热重分析表征印迹聚合物的性质,结果表明MWNTs表面成功接枝了一层稳定的、厚度为35～40nm具有识别能力的印迹聚合材料．结合高效液相色谱技术,通过填充色谱柱在线色谱分析,探讨不同pH值的流动相下该印迹材料对L-His的分离行为,结果表明MWNTs—MIPs色谱柱在流动相pH=7．0时分离效果最好,能够选择性地识别L-His和D-His,分离度R为1．78,选择因子α为1．28．     

Coating of multiwalled carbon nanotubes with polymer nanospheres through microemulsion polymerization

We report a simple and noncovalent method for coating multiwalled carbon nanotubes (MWCNTs) with polyaniline (PANI) nanospheres using a microemulsion polymerization method. In this method, aniline polymerization is performed with MWCNTs in the presence of sodium dodecyl sulfate (SDS), which serves as both a surfactant and a dopant. Morphological, structural, thermal, and electrical properties of MWCNT–PANI nanocomposites were analyzed. The TEM results of the nanocomposites prepared with surfactant reveal that 30–50-nm-diameter PANI nanospheres were coated on the surface of the MWCNTs. Composites prepared without surfactant were found to be in core–sheath-type cable structures. The conductivities of the nanocomposites synthesized through microemulsion polymerization were found to be one order of magnitude higher than both the conductivities of pure PANI and the composites prepared via in situ chemical polymerization without an assisting SDS surfactant. The mechanism for the formation of nanostructured composites is presented.     

Preconcentration of diazinon using multiwalled carbon nanotubes as solid-phase extraction adsorbents

A sensitive and selective column adsorption method is proposed for the preconcentration and determination of diazinon. Diazinon was preconcentrated on multiwalled carbon nanotubes (MWCNTs) as an adsorbent and then determined by high-performance liquid chromatography (HPLC). Several parameters on the recovery of the analyte were investigated. The experimental results showed that it was possible to obtain quantitative analysis when the solution pH was 6 using 200 mL of validation solution containing 2 μg of diazinon and 5 mL of acetonitrile as an eluent. Recovery of diazinon was 95.2 ± 4.2% with a relative standard deviation for seven determinations of 4.9% under optimum conditions. The maximum preconcentration factor was 200 for diazinon when 1000 mL of sample solution volume was used. The linear range of calibration curve was 0.3 to 10,000 ng mL^− 1 with a correlation coefficient of 0.997 and the detection limit (3S/N) was 0.06 ng mL^− 1. The proposed method was successfully applied to the determination of diazinon in tap water with high precision and accuracy.     

An unexpected new optimum in the structure space of DNA solubilizing single-walled carbon nanotubes

Here we report quantitative data on the amount of single-walled carbon nanotubes that can be suspended with oligodeoxynucleotides in aqueous buffer, together with rate constants for the thermal denaturation of the resulting DNA-nanotube complexes at elevated temperatures. Sequence motifs d(GT)n and d(AC)n with n=2, 3, 5, 10, 20, or 40 were employed, both individually and as equimolar mixtures of the complementary strands. Unexpectedly, the greatest suspending efficiency was found for the mixture of short, complementary oligonucleotides d(GT)3 and d(AC)3. Unlike the suspending efficiency, the kinetic stability of the nanotube suspensions increases with increasing chain length of the DNA, with half life times of >25 h at 90 degrees C for the complexes of the longest strands. Our results identify a new, unexpected optimum in DNA sequence space for suspending carbon nanotubes. They also demonstrate that suspending power depends on the presence of complementary strands. Exploratory assays suggest that nanotubes can be deposited site-selectively from suspensions formed with short DNA sequences.     

Methane preconcentration in a microtrap using multiwalled carbon nanotubes as sorbents

The GC monitoring of green house gases is a challenging task because the concentration of organic species such as methane are relatively low (ppm to ppb) and their analysis requires some level of preconcentration. Since methane is highly volatile, it is not easily retained on conventional sorbents. In this paper we present multiwalled carbon nanotubes (MWNTs) as an effective sorbent for a microtrap designed for methane preconcentration. Its performance was compared to other commercially available carbon based sorbents, and it was found to be the most effective sorbent in terms of breakthrough volume and enthalpy of adsorption.