不同电性Gemini表面活性剂界面扩张性质

利用Langmuir槽法研究了含聚氧乙烯醚链中间链的两性Gemini表面活性剂C8E4NC12、阳离子Gemini表面活性剂C12NE3NC12和阴离子Gemini表面活性剂C8E4C8在空气/水表面和癸烷/水界面上的扩张性质,考察浓度对3种Gemini表面活性剂溶液表、界面扩张性质的影响.结果表明,由于分子间存在库仑引力,两性Gemini分子表现出较高的扩张弹性和粘性,且界面扩张性质类似于表面.对于有相同电荷Gemini分子,C8E4C8分子中的刚性苯环导致其疏水长链在表面上的取向不同于C12NE3NC12分子,两者表现出不同的表面扩张性质;而油分子能改变同电荷Gemini分子中长链烷基的取向,造成其界面扩张弹性和粘性远低于表面.提出了不同电性Gemini分子在界面排布的示意图,并利用弛豫过程的特征参数进行了验证.     

阴离子Gemini表面活性剂在油/水界面行为的分子动力学模拟

采用分子动力学方法研究了磺酸盐型阴离子Gemini表面活性剂在油/水界面的吸附行为, 考察了不同长度的连接基(Spacer)对表面活性剂在界面的聚集形态及界面性质的影响. 密度分布和微观结构信息显示, Gemini表面活性剂能在油/水界面形成单层膜结构. Gemini表面活性剂能使油/水界面的厚度显著增大, 并使界面形成能降低. 当连接基为6个碳时, 此类磺酸盐型Gemini表面活性剂的界面厚度最大, 形成的界面最稳定. 连接基长度对Gemini表面活性剂单层膜周围的水分子和Na⁺的吸附结构影响不大, 但是能影响水分子的扩散行为.     

磺酸盐型Gemini表面活性剂合成研究进展

磺酸盐型Gimini表面活性剂是一类新型的阴离子表面活性剂,它由联结基团通过化学键将2个或多个单体磺酸盐型表面活性剂连接在一起,由此产生高表界面活性,低临界胶束浓度值,增强了洗涤能力,与传统的阴离子表面活性剂有较好的复配性,奇异的流变特性和良好的抗盐性等一系列的性质,从而具有广泛的应用前景。 本文以原料来源不同分类,综述了一系列磺酸盐型Gemini表面活性剂的合成方法,展望了合成磺酸盐型Gemini表面活性剂的研究方向。     

阴离子蠕虫胶束

本文从分析蠕虫胶束形成的分子几何条件和自由能驱动因素入手,总结了传统阴离子表面活性剂蠕虫胶束的形成和性质,指出制约其构筑和产生优良黏弹性的原因。在此基础上,介绍了Gemini表面活性剂构筑蠕虫胶束的分子结构优势,以及由此构筑阴离子蠕虫胶束的研究进展,尤其是长刚性联接链Gemini表面活性剂形成的蠕虫胶束。最后特别指出,基于新颖分子结构优势,Gemini表面活性剂可望成为蠕虫胶束构筑的主要分子对象。     

高盐油藏下两性/阴离子表面活性剂协同获得油水超低界面张力

研究了在高盐油藏中, 利用两性/阴离子表面活性剂的协同效应获得油水超低界面张力的方法. 两性表面活性剂十六烷基磺基甜菜碱与高盐矿化水具有很好的相容性, 但在表面活性剂浓度为0.07%-0.39%(质量分数)范围内仅能使油水界面张力达到10^-2 mN·m^-1量级, 加入阴离子表面活性剂十二烷基硫酸钠后则可与原油达到超低界面张力. 通过探讨表面活性剂总浓度、金属离子浓度、复配比例对油水动态界面张力的影响, 发现两性/阴离子表面活性剂混合体系可以在高矿化度、低浓度和0.04%-0.37%的宽浓度范围下获得10^-5 mN·m^-1量级的超低界面张力, 并分析了两性/阴离子表面活性剂间协同获得超低界面张力的机制.     

阿拉伯树胶对Gemini表面活性剂界面扩张流变性质的影响

利用悬挂滴方法研究了Gemini季铵盐表面活性剂(C₁₂-Ph-C₁₂和C₁₂-8-C₁₂)和阿拉伯树胶的界面张力和界面扩张流变性质, 考察了阿拉伯树胶对C₁₂-Ph-C₁₂和C₁₂-8-C₁₂溶液界面张力和界面扩张流变性质的影响. 研究结果表明, 1%(w)阿拉伯树胶的加入显著降低了C₁₂-Ph-C₁₂和C₁₂-8-C₁₂的界面张力, 但是界面扩张模量增加,这一变化主要是由于阿拉伯树胶分子与Gemini季铵盐表面活性剂分子通过静电相互作用形成复合物. 文中提出了不同结构Gemini季铵盐表面活性剂与阿拉伯树胶分子在界面排布的示意图.     

Gemini 阴离子表面活性剂水溶液的聚集性质

合成了一种Gemini阴离子表面活性剂,测定了其临界胶束浓度cmc和cmc时的表面张力γcmc,与传统的单基表面活性剂相比,其临界胶束浓度降低了一个数量级,具有突出的降低水的表面张力的效率;研究了该种Gemini表面活性剂的浓度对于胶束聚集数的影响,结果表明,随着浓度的增加,胶束聚集数出现了一个极大值,同时观察到液晶微相的生成.     

寡聚表面活性剂的合成及其聚集行为的研究

寡聚表面活性剂是由2个或2个以上单头单链的表面活性剂在头基处或靠近头基处由连接基团通过化学键连接而成的二聚、三聚、四聚乃至更高寡聚度的分子.Gemini表面活性剂(二聚表面活性剂)是最简单,也是最早被发现的寡聚表面活性剂,已经被大量报道.已有综述很好地总结了Gemini表面活性剂的物理化学性质.本文主要综述三聚及三聚以上寡聚表面活性剂的研究进展,包括寡聚表面活性剂的合成和结构、表/界面性质以及溶液中的聚集行为等,以期使研究者比较全面地认识寡聚表面活性剂领域的研究进展.     

烷基酚阴离子表面活性剂的合成与应用进展

将本实验室最新研究成果与相关文献报导相结合,介绍了目前以烷基酚为原料合成阴-非离子表面活性剂、Extended表面活性剂和Gemini表面活性剂的最新动态,特别注重它们在三次采油等非直接环境排放型应用场合的高效合理利用。指出深入开发区域选择性硫酸化/磺化、硫酸酯盐转磺酸盐、羟基直接氧化合成羧酸盐以及烷基酚偶联合成Gemini骨架等技术对于合理和高效利用烷基酚具有重要意义。     

新型阴离子Gemini表面活性剂与非离子表面活性剂C10E6混合溶液的胶团化的研究

研究了烷基苯磺酸盐Gemini表面活性剂Ia与非离子表面活性剂C10E6溶液混合胶团中分子间的相互作用. 通过表面张力法测定了Ia 和C10E6不同比例不同温度下的临界胶束浓度(cmc). 结果表明, 两种表面活性剂以任何比例复配的cmc比单一表面活性剂的cmc都低, 表现出良好的协同效应. 传统型非离子表面活性剂C10E6、Gemini表面活性剂Ia及混合物的cmc都随着温度升高而降低. 而且, 任何配比的混合胶团中两种表面活性剂分子间的相互作用参数β都是负值, 这说明两种表面活性剂在混合胶团中产生了相互吸引的作用. 混合表面活性剂体系的胶团聚集数比单一Ia的大, 但比单一C10E6的小. 向Gemini表面活性剂Ia胶束中加入非离子表面活性剂C10E6会使胶束的微观极性变小.     

阴离子孪连表面活性剂的合成及其表/界面活性研究

合成了疏水链长度不同和连接基长度不同的7种系列阴离子孪连表面活性剂,研究了它们的表/界面活性。结果表明,它们有较低的表面张力和临界胶束浓度(CMC),有很好的表面活性。它们的CMC都在10-5~10-6mol/L之间,表面张力在26·5~34mN/m之间。它们有非常好的抗一价、二价盐的能力。除了C16-C2-C16在高于5%的NaCl溶液中会产生析出外,其余孪连表面活性剂都能耐盐20%以上。随着盐浓度的增加,孪连表面活性剂与烷烃间的界面张力逐渐降低,能达到10-3mN/m。与中原油田原油间的界面张力能降低到10-3~10-4mN/m,表明它们可应用于特高矿化度油藏提高采收率。     

Study on the Interfacial Tensions Between Oils and Alkylbenzene Sulfonate Gemini Surfactant Solutions

Interfacial tensions (IFT) of five alkylbenzene sulfonate Gemini surfactants Ia, Ib, Ic, Id, and Ie at different oils/water systems were measured by a spinning drop interfacial tensiometer. And critical micelle concentration (CMC), the interfacial tension at CMC (γ_CMC), maximum interfacial excess concentration (Γ _max) and the surface area per molecule (A_min) were calculated. The results indicated that the CMC values determined with interfacial tension method were lower than those determined with surface tension method. And γ_CMC for Ie is larger than that for Ia, Ib, Ic, and Id. In addition, the effects of temperature and hydrophobic chains on dynamic IFT were also studied. With the increment of temperature, dynamic IFT is easier to reach a stable value. However, with the increment of hydrophobic chains, dynamic IFT is more difficult to reach a stable value. Each Gemini surfactant produces a minimum IFT when measured against a different n-alkane.     

CMC系列高分子表面活性剂与原油超低界面张力形成机理的研究

采用动态激光光散射及环境扫描电镜研究了羧甲基纤维素系列高分子表面活性剂与大庆原油形成超低界面张力的机理.结果表明,CMC系列高分子表面活性剂具有与低分子量表面活性剂相比拟的表/界面活性,其水溶液的表面张力可达2835mN/m,界面张力达到10^-110mN/m.碱的加入可显著降低高分子表面活性剂与原油的界面张力,在适当条件下界面张力达到超低值(10^-3mN/m),可望作为三次采油的驱油剂.等效烷烃模型研究表明,用碱与原油酸性组分的作用来解释碱能使界面张力下降至超低值的传统观点是不完善的,加入碱能使高分子表面活性剂胶束解缔,胶束数量增多,胶束粒径减小,单分子自由链增加,有利于高分子表面活性剂向界面迁移和排布,这是高分子表面活性剂和碱复配体系与原油界面张力下降至超低值的主要原因.     

Synergistic effect of mixed anionic and cationic surfactant systems on the interfacial tension of crude oil-water and enhanced oil recovery

Surfactant based enhanced oil recovery (EOR) is an interesting area of research for several petroleum researchers. In the present work, individual and mixed systems of anionic and cationic surfactants consisting of sodium dodecyl sulphate (SDS) and cetyltrimethylammonium bromide (CTAB) in different molar ratios were tested for their synergistic effect on the crude oil-water interfacial tension (IFT) and enhanced oil recovery performance. The combination of these two surfactant systems showed a higher surface activity as compared to individual surfactants. The effect of mixed surfactant systems on the IFT and critical micellar concentration (CMC) is strongly depends on molar ratios of the two surfactant. Much lower CMC values were observed in case of mixed surfactant systems prepared at different molar ratios as compared to individual surfactant systems. The lowest CMC value was found when the molar concentration of SDS was higher than the CTAB. When the individual and mixed surfacant systems were tested for EOR performance through flooding experiments, higher ultimate oil recovery was obtained from mixed surfactant flooding compared to individual surfactants. Combination of SDS and CTAB or probably other anionic-cationic surfactants show synergism with substantial ability to reduce crude oil water IFT and can be a promising EOR method.     

Investigation Static/Dynamic Surface and Interfacial Tension of Some Synthesized Polymeric Surfactants to Enhance the Egyptian Jet Fuel A1 Atomization

In the present work some exthoxylated polyalkylphenol surfactants have different alkyl chains (nonyl and dodecyl) were synthesized. The static surface tension for these surfactants in water and jet fuel A1 was measured and the critical micelle concentration (CMC) for each surfactant was determined. The data show the general trend of decreasing the CMC against the molecular weight of the synthesized polymeric surfactants. The HLB of these surfactants was also calculated. The dynamic surface tension for the synthesized surfactants was measured at CMC. The dynamic interfacial tension for these surfactants with jet fuel A1 at CMC was also measured using the spinning drop technique. The results showed that the effect of the synthesized surfactants on deceasing the time of droplet maturation was significant remarked. The decrease of this time leads to enhance of jet fuel atomization.     

Effect of Neck Formation on the Measurement of Dynamic Interfacial Tension in a Drop Volume Tensiometer

Dynamic interfacial tension values obtained by drop volume tensiometry will be affected under certain experimental conditions by the formation of a neck between the drop and the capillary tip. This phenomenon must be accounted for to obtain accurate values of interfacial tension. In this work, neck formation for a water–mineral oil system is studied under conditions where hydrodynamic effects can be neglected. A model originally developed for the determination of the surface tension of a suspended drop is modified for application to dynamic interfacial tensions of surfactant-containing liquids. The model relates apparent values of interfacial tension calculated from drops possessing necks to actual values. Experiments with Span 80 (sorbitan monooleate) and sodium dodecyl sulfate (SDS) surfactants in a mineral oil–water system are used to test the validity of the developed model. For the small tip diameter used, good agreement is obtained for Span 80 up to the critical micelle concentration, and for low concentrations of SDS, when the surfactant adsorption is diffusion-limited. In both cases, the neck diameter of the growing drop can be considered constant over the range of dynamic interfacial tensions tested.     

DTAB降低饱和烷烃与水的界面张力的研究

判断一种表面活性剂降低油-水界面张力性能的优劣,就需要对界面张力进行准确有效的测量。文章就不同浓度的十二烷基三甲基溴化铵(DTAB)水溶液分别与正庚烷(n-Heptane)和正十六烷(n-Hexadecane)之间的界面张力进行定量的测量,分别得到了在30℃下水-正庚烷和水-正十六烷体系的界面张力随DTAB浓度变化的曲线。结果表明,在DTAB浓度达到其所在体系中的CMC值时,水-正庚烷体系界面张力小于水-十六烷体系界面张力。DTAB具有较强的抗矿盐能力,界面张力随温度升高有所下降。     

正负离子混合表面活性剂双水相界面张力的研究

用旋转滴法测定了正负离子混合表面活性剂形成的双水相界面张力, 研究了双水相界面张力与表面活性剂的分子结构、正负离子表面活性剂的摩尔比、总浓度、外加无机盐及温度的关系. 结果表明, 双水相界面张力在一定正、负离子表面活性剂的摩尔比时属于超低界面张力范围. 观察到三种界面张力曲线类型, 第一类为摩尔比1:1 的两边的两条曲线, 界面张力随过剩表面活性剂组分的比例增加而降低; 第二类为一条跨过摩尔比1:1的马鞍型曲线; 第三类为位于摩尔比1:1的一边的一条马鞍型曲线. 界面张力曲线的类型主要取决于表面活性剂的分子结构, 包括亲水基类型、疏水链长度及对称性.     

新型磺基甜菜碱/聚丙烯酰胺体系表面及界面性能

采用自制的新型磺基甜菜碱两性表面活性剂与相对分子质量2500万的聚丙烯酰胺进行复配,考察了不同温度和矿化度条件下,聚合物对复配溶液表面、界面性能的影响。 采用滴体积法测定了溶液的表面张力,结果表明,加入聚合物使溶液的临界胶束浓度增大,且复配溶液的表面张力大于单独表面活性剂溶液的表面张力。 当聚合物浓度一定,增大溶液矿化度时,体系表面张力增大。 用旋滴型界面张力仪测定了溶液的界面张力,结果表明,增大聚合物浓度,油水界面张力增大,增大溶液矿化度,油水界面张力有所升高。 聚合物质量浓度为1.5 g/L,表面活性剂质量浓度为0.3 g/L时,可使胜利油田孤岛原油和孤东原油的油水界面张力达到超低数量级（10-3 mN/m）。 用分水时间法测定了溶液的乳化性能,结果表明,聚合物浓度增大,分水时间延长,并考察了75、85和95 ℃条件下体系的乳化性能,温度越高,分水时间越短。     

Experimental Study of the Effect of Strong Alkali on Lowering the Interfacial Tension of Oil/Heavy Alkylbenzene Sulfonates System

Experimental studies were conducted to explore the fundamental mechanisms of alkali to lower the interfacial tension of oil/heavy alkylbenzene sulfonates (HABS) system. Sodium hydroxide was used as the strong alkali chemical to investigate the interfacial tension (IFT) of oil/HABS system. The influences of salt and alkali on the interfacial activity were studied by the measurement of interfacial tension and partition coefficient. Moreover, the alkali/surfactant solutions were measured by dynamic laser scattering. The results showed that compared with the salt, the function of alkali to lower the interfacial tension and improve partition coefficient is more significant. The micelles formed by surfactants could be disaggregated because of adding alkali, so the size of micelles decreases and the number of mono‐surfactants increases, then more surfactant molecules move to the interface of oil/surfactant system and the adsorption of surfactants at oil‐water interfaces increases, which can lead to the decrease of IFT.