SI-traceable certification of the amount content of cadium below the ng g(-1) level in blood samples by isotope dilution ICP-MS applied as a primary method of measurement

The development and implementation of a method for the certification of cadmium in blood samples at low ng g(-1) and sub ng g(-1) levels is described. The analytical procedure is based on inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) applied as a primary method of measurement. Two different sample digestion methods, an optimized microwave digestion procedure using HNO3 and H2O2 as oxidizing agents and a high-pressure asher digestion procedure, were developed and compared. The very high salt content of the digests and the high molybdenum content, which can cause oxide-based interferences with the Cd isotopes, were reduced by a chromatographic matrix separation step using an anion-exchange resin. All isotope ratio measurements were performed by a quadrupole ICP-MS equipped with an ultrasonic nebulizer with membrane desolvator. This sample introduction set-up was used to increase sensitivity and minimize the formation of oxides (less MoO+ interference with the Cd isotopes). Because of the very low Cd concentrations in the samples and the resulting need to minimize the procedural blank as much as possible, all sample-processing steps were performed in a clean room environment. Detection limits of 0.005 ng g(-1) Cd were achieved using sample weights of 2.7 g. The method described was used to recertify the cadmium content of three different blood reference materials from the Community Bureau of Reference (BCR) of the European Commission (BCR-194, BCR-195, BCR- 196). Cadmium concentrations ranged between approximately 0.2 ng g(-1) and approximately 12 ng g(-1). For these materials, SI-traceable certified values including total uncertainty budgets according to ISO and Eurachem guidelines were established.     

Isotopic determination of selenium in biological materials with inductively coupled plasma mass spectrometry

A method for the isotopic determination of selenium in biological matrices is described. The method is based on hydride generation inductively coupled plasma mass spectrometry (ICP-MS). The development is specifically related to the requirements of stable isotope tracer studies in human subjects. The method is based on isotope dilution using 82Se as the in vitro spike and can quantify the 74Se and 77Se contents of samples. It involves wet oxidation (HNO3 - H2O2 or HNO3 - HClO4) of the 82Se-spiked matrix, reduction to selenite by boiling with HCl followed by measurement of the isotope ratios (82Se/77Se and 74Se/77Se) in the gas stream (H2Se) generated from on-line reduction of the sample selenite with NaBH4. Compared with the isotopic signal resulting from a selenite solution containing 5 ng ml-1 of Se, the total sample blank contributions at m/z = 74, 77 and 82 were less than 5% of the respective isotope signal. Worst-case absolute detection limits were 0.2-0.9 ng of Se, depending on the isotope used. Ion beam intensity ratios were measured with an over-all precision [relative standard deviation (RSD)] of 1% for both isotope pairs. Measured ratios (MRa/b) were stable during a given day's operation within the expected precision of the measurements but varied for different days. The magnitude of MRa/b was generally independent of the nature of the matrix. Highly linear relationships were found between ion beam intensity ratios (MRa/b) and the corresponding true isotope ratios for calibration solutions whose isotope ratios had been altered by as much as one order of magnitude.(ABSTRACT TRUNCATED AT 250 WORDS)     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Optimization of microwave digestion for mercury determination in marine biological samples by cold vapour atomic absorption spectrometry

Optimization of acid digestion method for mercury determination in marine biological samples (dolphin liver, fish and mussel tissues) using a closed vessel microwave sample preparation is presented. Five digestion procedures with different acid mixtures were investigated: the best results were obtained when the microwave-assisted digestion was based on sample dissolution with HNO3-H2SO4-K2Cr2O7 mixture. A comparison between microwave digestion and conventional reflux digestion shows there are considerable losses of mercury in the open digestion system. The microwave digestion method has been tested satisfactorily using two certified reference materials. Analytical results show a good agreement with certified values. The microwave digestion proved to be a reliable and rapid method for decomposition of biological samples in mercury determination.     

Development of an ICP-IDMS method for accurate routine analyses of toxic heavy metals in polyolefins and comparison with results by TI-IDMS

An inductively coupled plasma isotope dilution mass spectrometric (ICP-IDMS) method was developed as a suitable method - with respect to its sensitivity, precision, accuracy, and time-consumption - for the analysis of toxic heavy metal traces (Pb, Cd, Cr, and Hg) in polyolefins. Results for Pb, Cd, and Cr were compared with those obtained by thermal ionization isotope dilution mass spectrometry (TI-IDMS), which was used as a reference method. Because of its high first ionization potential and its high volatility mercury could not be determined by TI-IDMS. A multi-element spike solution, containing isotopically enriched 206Pb, 116Cd, 53Cr, and 201Hg, was used for the isotope dilution step. Decomposition of the polyolefin samples was carried out with concentrated HNO3 at temperatures of about 300 degrees C in a high pressure asher (HPA). This procedure decomposes polyolefins completely and allows isotopic equilibration between sample and spike isotopes. Detection limits of 16 ng/g, 5 ng/g, 164 ng/g, and 9 ng/g were obtained for Pb, Cd, Cr, and Hg by ICP-IDMS using only sample weights of 0.25 g. In different commercially available polyethylene samples heavy metal concentrations in the range of < 5 ng/g to 4 x 10(3) ng/g were analyzed. Both mass spectrometric methods were applied within the EU project "Polymeric Elemental Reference Material (PERM)" for the certification of two polyethylene reference materials. The ICP-IDMS results agreed very well with those of TI-IDMS which demonstrates the accuracy of the ICP-IDMS method also suitable for routine analyses.     

Isotope dilution gas chromatography/mass spectrometry for platinum determination in urine

The therapeutic importance of platinum (Pt) compounds, the growing accessibility of gas chromatography/mass spectrometry (GC/MS) systems in clinical laboratories, and the lack of a mass spectrometric method for the determination of Pt in biological samples motivated us to develop an isotope dilution GC/MS assay for Pt. The method is based on the use of lithium bis(trifluoroethyl) dithiocarbamate, Li(FDEDTC), as a chelating agent and enriched ¹⁹²Pt for isotope dilution. Conditions were optimized for the precise and accurate determination of isotope ratios of Pt by using a 10-m DB-l fused silica capillary column and a reverse-geometry double-focusing mass spectrometer with selected ion monitoring. An overall precision of 1% was obtained by combining within-run precision and between-run precision at the 10-ng level. No appreciable memory effect was observed when samples with different isotope ratios were analyzed sequentially. The method was validated by the quantitation of Pt in National Institute of Standards and Technology freeze-dried urine sample SRM 2670. A concentration value of 125 ± 6 /Lg/L (n = 6) was obtained by using four different sets of isotope ratios in the molecular ion and supports the National Institute of Standards and Technology recommended value of 120 ± ? μg/L. Limits-of-quantitation, estimated at 3 μg/L, are made possible by the high sensitivity of the method and the low blank value for Pt.     

Determination of ultratrace bismuth in milk samples by atomic fluorescence spectrometry

A sensitive procedure was developed for determination of bismuth (Bi) in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS) after microwave-assisted sample digestion with HNO3 and H2O2. The method provides a sensitivity of 1832 fluorescence units (ng/mL) with a detection limit of 0.01 ng/mL, which corresponds to 20 pg absolute limit of detection, equivalent to 0.50 ng/g in the original sample. Application of the methodology to cow milk samples from the Spanish market showed the presence of Bi at a concentration of 11.8-28.8 ng/g, which compared well with data obtained after dry ashing of samples and with data obtained by inductively coupled plasma-mass spectrometry after microwave-assisted digestion.     

Direct determination of Cd, Cu and Pb in wines and grape juices by thermospray flame furnace atomic absorption spectrometry

The applicability of thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) was evaluated for direct determination of Cu, Cd and Pb in wines and grape juices. The developed procedure does not require preliminary acid digestion of the samples. The optimum conditions for determination of Cu, Cd and Pb in wines were studied and the performance was compared to those typically obtained by flame atomic absorption spectrometry (FAAS). A sample volume of 150 microL was introduced into a heated nickel tube at a flow rate of 0.54 mLmin(-1) and 0.14 molL(-1) HNO(3) was used as sample carrier flowing at 2.5 mLmin(-1) for determining all analytes. The effect of ethanol concentrations on Cu, Cd and Pb absorbance signals were studied. All determinations were carried out by adopting optimized conditions and quantification was based on the standard additions method. Limits of detection (LOD) of 12.9, 1.8 and 5.3 microgL(-1) (n=14) for Cu, Cd and Pb, respectively, were obtained for wine samples (3sigma(blank)/slope, n=14). Relative standard deviations (R.S.D., %) of 2.7, 2.1 and 2.6 for Cu, Cd and Pb, were obtained (n=6) for wine samples. The values determined for grape juice samples were similar to these ones. The analytical throughput was 45 determinations h(-1) and accuracy was checked by addition-recovery experiments.     

Development of an on-line isotope dilution laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) method for determination of boron in silicon wafers

A method has been developed based on an on-line isotope dilution technique couple with laser ablation/inductively coupled plasma mass spectrometry (LA-ICP-MS), for the determination of boron in p-type silicon wafers. The laser-ablated sample aerosol was mixed on-line with an enriched boron aerosol supplied continuously using a conventional nebulization system. Upon mixing the two aerosol streams, the isotope ratio of boron changed rapidly and was then recorded by the ICP-MS system for subsequent quantification based on the isotope dilution principle. As an on-line solid analysis method, this system accurately quantifies boron concentrations in silicon wafers without the need for an internal or external solid reference standard material. Using this on-line isotope dilution technique, the limit of detection for boron in silicon wafers is 2.8 × 10¹⁵ atoms cm⁻³. The analytical results obtained using this on-line methodology agree well with those obtained using wet chemical digestion methods for the analysis of p-type silicon wafers containing boron concentrations ranging from 1.0 × 10¹⁶ to 9.6 × 10¹⁸ atoms cm⁻³.     

Determination of trace elements including platinum in tree bark by ICP mass spectrometry

The increasing emission of Pt-group metals from automobile catalytic converters requires the development of highly sensitive procedures for ultratrace analysis of environmental and biological systems. Tree bark, located close to motorway or industrial areas, was utilised as a substrate for collection of airborne particulate matter and samples after digestion (microwave assisted dissolution with HNO3 and HCl) were analysed by ICP mass spectrometry. The study targeted Pt and other metallic contaminants and involved analysis of some 57 tree bark samples using both quadrupole and double-focusing sector field ICP mass spectrometers. Detection limits for platinum determination in tree bark were 0.03 ng/g (DF-ICP-MS) and 0.2 ng/g (ICP-QMS). The platinum content of the bark samples ranged from 0.07-5.4 ng/g.     

Determination of mercury, selenium, bismuth, arsenic and antimony in human hair by microwave digestion atomic fluorescence spectrometry

A novel method for determination of Hg, Se, Bi, As and Sb based on microwave digestion followed by continuous flow vapour generation atomic fluorescence spectrometry was developed. The digestion for Hg was based on a two stage digestion involving HNO(3) and H(2)O(2), whilst for the hydride forming elements a common digestion using HCl and H(2)O(2) was found to be the most effective. The instrumentation and chemistry were optimised in order to provide the best accuracy and precision. The method detection limit for hair samples was found to be 0.2 ng g(-1) for Hg and between 2 and 10 ng g(-1) for the hydride forming elements. The atomic fluorescence detector showed excellent linearity over the concentration ranges studied with linear correlation co-efficients between 0.99984 and 0.99997. To validate the accuracy of the method a human hair certified reference material (GBW 0706) was analysed and excellent agreement with the certified value was obtained for all elements.     

Determination of thirteen common elements in food samples by inductively coupled plasma atomic emission spectrometry: comparison of five digestion methods

Five sample digestion procedures were evaluated for the determination of Al, B, Ca, Cu, Fe, K, Mg, Mn, Na, P, S, Sr, and Zn in food samples by inductively coupled plasma atomic emission spectrometry. The 5 procedures include dry ashing at 500 degrees C, wet digestion with HNO3-HClO4, microwave digestion with HNO3, microwave digestion with HNO3-H2O2, and microwave digestion with HNO3-H2O2-HF. For microwave digestion with HNO3-H2O2-HF, silicon (IV) oxide was used to eliminate the excess HF, making it possible to determine total Al, B, and other common elements accurately and simultaneously. Seven National Institute of Standards and Technology standard reference materials (SRMs) were analyzed to compare the recovery of 13 elements with above digestion procedures. The results demonstrated that the microwave digestion procedure with HNO3-H2O2-HF yielded the best recoveries for all 13 elements in the selected SRMs. The determined concentrations of most elements were close for all 3 microwave digestion procedures with the exception of Al in oyster tissue, bovine liver, and spinach. Notably, the wet digestion with HNO3-HClO4 is the simplest and the most effective procedure for the selected elements except Al and B. Although there are several concerns with the dry ashing procedure, it might be a preferable procedure for those analyses where only nonvolatile elements are to be determined and the concentrations of the elements are low.     

电感耦合等离子体发射光谱法测定REACH法规涉及产品中铅、铬、钴、砷、锡、铝、锆、钼和硼

采用电感耦合等离子体原子发射光谱法对REACH法规涉及产品中铅、铬、钴、砷、锡、铝、锆、钼和硼的含量进行测定。0.2g样品经微波消解处理,聚合物材质试样以8mL硝酸和2mL过氧化氢为消解试剂;无机非金属材质试样以6mL硝酸、2mL过氧化氢和2mL氢氟酸为消解试剂。各元素的方法检出限均低于15mg·kg-1。方法的加标回收率在82.4%～108%之间,测定值的相对标准偏差(n=7)在3%～6%之间。     

Mechanised flow system for on-line microwave digestion of food samples with off-line catalytic spectrophotometric determination of cobalt at ng l-1 levels

A mechanised system for on-line slurry food sample digestion was developed and an off-line cobalt determination was performed. The stabilised slurry sample was introduced into an air carrier stream until reaching the digestion coils located inside a household microwave oven. Software written in Visual Basic 3.0 was developed to permit the transport of the slurry samples and the programming of the microwave oven and also the control of the mineralization valve. The proposed system was optimized for determination of cobalt in certified samples such as mussels, bovine liver and fish and also uncertified fish samples. The digestion parameters were established as 3 mol l-1 HNO3 for mussels, 3 mol l-1 HNO3 plus 0.16% v/v H2O2 for bovine liver and 12 mol l-1 HNO3 for fish employing maximum power for 5 min of microwave actuation. In the subsequent spectrophotometric method for the catalytic determination of cobalt, the Tiron and hydrogen peroxide concentrations were 1.8 x 10(-3) and 3.0 x 10(-4) mol l-1, respectively, and the sample residence time was 300 s as determined by an optimisation process. The proposed method features a linear range from 10 to 200 ng l-1 Co (r > 0.996) with detection and quantification limits of 1.7 and 5.5 ng l-1 Co, respectively. The precision, expressed as RSD, was 2.4% (n = 12) for repeatability and 5.2% (n = 10) for reproducibility and the accuracy of the proposed method was assessed by using certified samples and an alternative technique (ETAAS).     

Ion chromatographic determination of trace level phosphorus in purified quartz

Trace levels of phosphorus in purified quartz are determined by ion chromatography. In situ reagent purification, matrix digestion and oxidation of phosphorus to orthophosphate ion are carried out simultaneously in a vapour phase digestion (VPD) assembly using a mixture of HF, HNO3 and H2O2. A drastic reduction (475 times) in phosphate blank from reagents (HF/H2O2) was achieved in the VPD through in situ purification of the reagent. The residues remaining after volatilisation (solvent/matrix), mostly consisting of insoluble phosphate/fluoride salts of divalent and trivalent cations, were solubilised by ion-exchange dissolution. Phosphate was analysed on the IonPac AS17 column with suppressed conductivity detection. The results of the ion chromatography (IC) method were compared with a spectrophotometric method. Accuracy was evaluated by analysing a certified reference material (silicon, NIST 57a). The method detection limit was 0.05 microg g(-1).     

Determination of zirconium traces in polymers by ICP-IDMS – a powerful and fast method for routine testing of zirconium residues in polyolefins

Zirconium trace analyses play an important role for polyolefins produced by modern catalytic processes with zirconium metallocenes. A reliable and fast routine testing method by inductively coupled plasma isotope dilution mass spectrometry (ICP-IDMS) was therefore developed, which allows the determination of zirconium in polymers down to the low ng/g level. With respect to its precision, accuracy, and time-consumption this method is suitable for routine testing of production processes. A spike solution, enriched in the stable isotope ⁹¹Zr, was prepared and used for the isotope dilution procedure, which has the advantage of being an internal “one point” calibration method. The polyolefin samples were dissolved by microwave assisted digestion with a mixture of concentrated HNO₃/HF.     

Development and application of new iondashexchange techniques for the separation of the platinum group and other siderophile elements from geological samples

Two new aniondashexchange techniques have been developed for the separation of the platinum group elements Ru, Pd, Ir, Pt and the siderophile metals Re, Ag, Zn and Cd from geological samples following a NiS fire assay digestion procedure. Both methods are simple and permit the isolation of these elements in sufficient purity for quantitative analysis by isotope dilutiondashinductively coupled plasma mass spectrometry (ID-ICPMS) at yields of 75-95%. The high affinity of the considered elements to anion exchange resins allows the use of small (1.25 ml) columns even for the processing of 5-10 g sized silicate rock samples. Following fire assay digestion and dissolution of the NiS buttons in aqua regia, the samples are loaded onto the resin bed as solutions in 1 M HCl. After elution of the bulk sample matrix with dilute HCl and HNO(3), Zn and Cd are stripped from the column using 0.8 M HNO(3). Small amounts of bromine water are added to the dilute mineral acids for the stabilization of strongly retained Ir(IV). Following this, the iondashexchange techniques permit the sequential elution of Ag, Re and the PGE using 11 M HCl, 8 M HNO(3) and 13.5 M HNO(3). The iondashexchange methods have been applied to separation of Ru, Pd, Re, Ir and Pt from the geological reference material SU-la prior to concentration measurements by ID-ICPMS. Our analytical results are in good agreement with previously published data for this sample and display an external reproducibility (based upon repeat dissolutions) of approximately 2-10% for the elements considered in this study.     

Trace metal analysis of coal fly ash collected plain and on a quartz fibre filter

A simple, uniform procedure has been developed for microwave-based digestion of fly ash samples collected from the hoppers of an electrostatic precipitator (ESP), or collected from flue gases on a heat-resistant quartz fibre filter and for subsequent atomic absorption spectrometric analysis of trace metals (Be, Cd, Co, Cr, Cu, Mn, Ni, Pb, V and Zn). HNO(3), HCl, HF and mixtures have been tested as digestion acids. The combination of HNO(3) and HF has been found to be efficient for the digestion of fly ash samples with and without quartz fibre filter material. In spite of the complicated matrix, results with satisfactory accuracy and precision (relative standard deviation below 10% for most of the elements) have been obtained. In the case of analysis of fly ash together with a quartz fibre filter, the calibration curve has to be determined by standard addition to a blank solution containing a dissolved blank quartz fibre filter.     

Evaluation of the combined measurement uncertainty in isotope dilution by MC-ICP-MS

The combination of metrological weighing, the measurement of isotope amount ratios by a multicollector inductively coupled plasma mass spectrometer (MC-ICP-MS) and the use of high-purity reference materials are the cornerstones to achieve improved results for the amount content of lead in wine by the reversed isotope dilution technique. Isotope dilution mass spectrometry (IDMS) and reversed IDMS have the potential to be a so-called primary method, with which close comparability and well-stated combined measurement uncertainties can be obtained.This work describes the detailed uncertainty budget determination using the ISO-GUM approach. The traces of lead in wine were separated from the matrix by ion exchange chromatography after HNO(3)/H(2)O(2) microwave digestion. The thallium isotope amount ratio ( n((205)Tl)/ n((203)Tl)) was used to correct for mass discrimination using an exponential model approach. The corrected lead isotope amount ratio n((206)Pb)/ n((208)Pb) for the isotopic standard SRM 981 measured in our laboratory was compared with ratio values considered to be the least uncertain. The result has been compared in a so-called pilot study "lead in wine" organised by the CCQM (Comité Consultatif pour la Quantité de Matière, BIPM, Paris; the highest measurement authority for analytical chemical measurements).The result for the lead amount content k(Pb) and the corresponding expanded uncertainty U given by our laboratory was:k(Pb)=1.329 x 10-10mol g-1 (amount content of lead in wine)U[k(Pb)]=1.0 x 10-12mol g-1 (expanded uncertainty U=kxuc, k=2)The uncertainty of the main influence parameter of the combined measurement uncertainty was determined to be the isotope amount ratio R(206,B) of the blend between the enriched spike and the sample.     

Determination of trace amounts of cadmium, lead, copper and zinc in natural waters by inductively coupled plasma atomic emission spectrometry with thermospray nebulisation, after enrichment on Chelex-100

Enrichment on Chelex-100, followed by evaporation when necessary, was used for the pre-concentration of Cd, Pb, Cu and Zn from natural waters. The measurements were carried out with inductively coupled plasma atomic emission spectrometry using a thermospray nebulisation system to reach the required sensitivity. The detection limits corresponding to three times the standard deviation of the blank (in 1% v/v HNO3) after a 30-fold enrichment are 0.02 microgram l-1 for Cd, 0.33 microgram l-1 for Pb and 0.03 microgram l-1 for Cu and Zn. Matrix effects, which are fairly serious with thermospray nebulisation, were taken into account by using the standard additions method. Results obtained for several river water samples were compared with those found by analysis of the non-enriched sample with inductively coupled plasma mass spectrometry or graphite furnace atomic absorption spectrometry. In all instances the agreement was satisfactory.