Measuring particle size-dependent physicochemical structure in airborne single walled carbon nanotube agglomerates

As-produced single-walled carbon nanotube (SWCNT) material is a complex matrix of carbon nanotubes, bundles of nanotubes (nanoropes), non-tubular carbon and metal catalyst nanoparticles. The pulmonary toxicity of material released during manufacture and handling will depend on the partitioning and arrangement of these components within airborne particles. To probe the physicochemical structure of airborne SWCNT aggregates, a new technique was developed and applied to aerosolized as-produced material. Differential Mobility Analysis-classified aggregates were analyzed using an Aerosol Particle Mass Monitor, and a structural parameter Γ (proportional to the square of particle mobility diameter, divided by APM voltage) derived. Using information on the constituent components of the SWCNT, modal values of Γ were estimated for specific particle compositions and structures, and compared against measured values. Measured modal values of Γ for 150 nm mobility diameter aggregates suggested they were primarily composed of non-tubular carbon from one batch of material, and thin nanoropes from a second batch of material – these findings were confirmed using Transmission Electron Microscopy. Measured modal values of Γ for 31 nm mobility diameter aggregates indicated that they were comprised predominantly of thin carbon nanoropes with associated nanometer-diameter metal catalyst particles; there was no indication that either catalyst particles or non-tubular carbon particles were being preferentially released into the air. These results indicate that the physicochemistry of aerosol particles released while handling as-produced SWCNT may vary significantly by particle size and production batch, and that evaluations of potential health hazards need to account for this. Disclaimer: The mention of any company or product does not constitute an endorsement by the Centers for Disease Control and Prevention. The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.     

Effect of metal oxide and oxygen on the growth of single-walled carbon nanotubes by electric arc discharge

The effect of oxygen on the growth of single-walled carbon nanotubes was studied with Ni–Co alloy powder as catalyst under helium atmosphere of 500 Torr by electric arc discharge. The oxygen included in nickel or (and) cobalt oxides was added in catalyst. The content of oxygen in atmosphere was controlled by changing vacuum degree inside furnace before inputting buffer gas. The examinations of TEM and Raman scattering showed that oxygen in metal oxide as catalyst promotes the nucleation of SWCNT by taking effect on the metal catalyst particles. However, O₂ in atmosphere has the role of oxidizing amorphous particles along with nanotubes. When its molar proportion is higher than 0.22 ppm (Parts per million), the carbon nanotubes produced are oxidized and their purity decreases. The diameter of single-walled carbon nanotube obtained under different condition has a narrow distribution around 1.28 nm.     

Measurements of work function of pristine and CuI doped carbon nanotubes

We report the results on measurements of the work function of carbon nanotubes and carbon-nanotube-based materials including pristine multi-walled and single-walled carbon nanotubes as well as single-walled carbon nanotubes intercalated by CuI with the Kelvin probe technique. We found the work function value 4.97–4.98 eV for pristine carbon nanotubes, while carbon nanotubes infilled with CuI demonstrate the work function value decreased by more than 0.1 eV (4.86–4.96 eV).     

Field—ion microscopy observation of single—walled carbon nanotubes

Field-ion microscopy(FIM),a tool for surface analysis with atomic resolution,has been employed to observe the end structure of single-walled carbon nanotubes(SWCNTs).FIM images revealed the existence of open SWCNT ends,Amorphous carbon atoms were also observed to occur around SWCNTs and traditional field evaporation failed to remove them.Heat treatment was found to be efficacious in altering the end structures of SWCNT bundles.Carbon and oxygen atoms released from heated tungsten filament are believed to be responsible for the decoration imposed on the SWCNT ends.     

Micromechanical properties of poly(butylene terephthalate) nanocomposites with single- and multi-walled carbon nanotubes

Polymer nanocomposites with carbon nanotubes (CNT) are becoming important structural materials because of their superior mechanical properties and easy processability. The objective of the work is to investigate the influence of small amounts of single walled carbon nanotubes (SWCNT), as well as multi-walled carbon nanotubes (MWCNT), on the microhardness of a thermoplastic polymer such as poly(butylene terephthalate) (PBT). The nanocomposites were obtained by introducing the CNT into the reaction mixture during the synthesis of PBT. The polymers without carbon nanotubes (reference material) and with carbon nanotubes were synthesized using an in-situ polycondensation reaction process. Weight percentages ranging from 0.01 to 0.2 wt% of the single walled and from 0.01 to 0.35 wt% of the multi-walled nanotubes were dispersed in 1,4-butanediol (BD) by ultrasonication and by ultra high speed stirring. The nanocomposites were extruded followed by injection molding. The samples were characterized by electron microscopy and microindentation hardness techniques. The variations of the micromechanical properties (indentation hardness) of the nanocomposites with nanotube content and with temperature are discussed in the light of the stress transfer between the polymer matrix and nanotubes, the degree of dispersion, the nature of the tubes and other structural parameters.     

结构与尺寸对碳纳米管物理吸附储氢的影响

采用巨正则蒙特卡罗方法,在298K和10MPa下,系统地研究了碳纳米管及其阵列的物理吸附储氢量与单壁管的管径、多壁管的层间距和管层数、单壁管阵列的管间距和排列方式的关系.发现单壁管的管径等于6nm时,管内的储氢密度达到最大;多壁管的层间距由034nm增大至061或088nm时,物理吸附储氢量明显增大;单壁管阵列的管间距等于17nm时,其管外间隙处的储氢密度达到最大,且方阵阵列优于三角阵列;当单壁管阵列的管间距大于06nm时,其管外的储氢密度均大于管内的储氢密度.指出合理地选择单壁管的管径、多壁管的层间距、单壁管阵列的管间距和排列方式,可以有效地提高碳纳米管及其阵列的物理吸附储氢量,并给出了相应的理论解释.     

多壁碳纳米管阵列场发射研究

研究了Ar离子束轰击及温度对多壁碳纳米管阵列场发射性能的影响.经Ar离子轰击35min后，发现阵列顶端的Fe催化剂颗粒明显减少，弯曲的顶部被轰击掉，使碳纳米管的场发射电流明显减小而场发射像无明显改变.温度的增加引起碳纳米管的场发射电流也随之增加.还研 究了在透明阳极技术中涂在阳极的荧光粉对场发射电流的影响.对同一碳纳米管阵列样品，发现涂有荧光粉的透明阳极使测量到的场发射电流大幅度减小，只是未涂荧光粉阳极电流的 1/30左右.直接用二氧化锡导电膜作阳极时，测得样品的开启场强为1.0V/μm.沉积了荧光粉的二 关键词： 多壁碳纳米管 场发射     

Functional multi-walled carbon nanotube/polysiloxane composite films as supports of PtNi alloy nanoparticles for methanol electro-oxidation

We demonstrate the use of molecular monolayers to enhance the nucleation of electrocatalytically active PtNi alloy nanoparticles onto the multi-walled carbon nanotubes (MWCNTs). After the siloxane was polymerized on the nanotube surfaces, the carbon nanotubes were embedded within the polysiloxane shell with a hydrophilic amino group situated outside. Subsequent deposition of PtNi nanoparticles led to high density of 3-10 nm diameter PtNi alloy nanoparticles uniformly deposited along the length of the carbon nanotubes. The presence of MWCNTs and PtNi in the composite films was confirmed by transmission electron microscopy (TEM), X-ray diffraction (XRD) and energy dispersion X-ray spectra analysis (EDS). The electrocatalytic activity of the PtNi-modified MWCNT/polysiloxane (PtNi/Si-MWCNT) composite electrode for electro-oxidation of methanol was investigated by cyclic voltammetry (CV), and excellent electrocatalytic activity can be observed.     

Modeling the binding of peptides on carbon nanotubes and their use as protein and DNA carriers

An in-depth study of a novel functionalization of carbon nanotubes for their application as protein and DNA carriers is presented. First, the optimum conditions for the dispersion of single-walled carbon nanotubes (SWCNTs) with amphiphilic polypeptides were obtained, and the SWCNT–polypeptide complexes were characterized by different techniques (UV–Vis-NIR, CD, and AFM). Based on the properties of the SWCNT–polypeptide complexes, a model that characterizes the adsorption of natural proteins onto SWCNT was described for the first time. This model predicts the adsorption of natural proteins on SWCNTs based on the protein structure and composition, and therefore, allows the design of methods for the preparation of SWCNT–protein complexes. Besides, the use of cationic-designed amphiphilic polypeptides to disperse SWCNTs is applied for subsequent and efficient binding of DNA to carbon nanotubes by a bilayer approach. Therefore, in this article, we develop procedures for the use of SWCNTs as protein and DNA carriers. The systems were delivered into cells showing that the efficiency of delivery is affected by the charge of the complexes, which has important implications in the use of SWCNT as platforms for protein and DNA binding and subsequent use as delivery systems.     

Investigation of the Morphological and Mechanical Properties of Polyethylene Terephthalate (PET)/Ethylene Propylene Diene Rubber (EPDM) Blends in the Presence of Multi-Walled Carbon Nanotubes

In this study the blends of polyethylene terephthalate (PET)/ethylene propylene diene rubber (EPDM) in the presence of multi-walled carbon nanotubes (MWCNT) (1 and 3?wt %) were prepared by melt compounding in an internal mixer. Mechanical and morphological properties of the nanocomposites were investigated. The thermal behaviors of the PET/EPDM nanocomposites were also investigated, by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The results of the mechanical tests showed that the tensile strength, elastic modulus and the hardness of the blends were increased with increasing CNT, while the impact strength and elongation at break decreased. The DSC and TGA results showed an increase of melting temperature (T_m) and degradation temperature of the nanocomposites with the addition of the carbon nanotubes, because the carbon nanotubes serve both as nucleating agents to increase T_m and prevent the composite from degradation to increase the thermal stability. The microstructure of the composites was evaluated through field emission scanning electron microscopy (FESEM) and the results showed a good distribution of the MWCNT within the polymer blend.     

Polyelectrolyte Nanocomposite Membranes with Imidazole-Functionalized Multi-Walled Carbon Nanotubes for Use in Fuel Cell Applications

The preparation and characterization of a new type of nanocomposite polyelectrolyte membrane (PEM), based on Nafion® and imidazole modified multi-walled carbon nanotubes (MWCNT-Im), for direct methanol fuel cell (DMFC) applications is described. Related to the interactions between the protonated imidazole groups, grafted on the surface of multi-walled carbon nanotubes (MWCNT), and the negatively charged sulfonic acid groups of Nafion®, new electrostatic interactions can be formed in the interface of the Nafion® and MWCNT-Im which result in both lower methanol permeability and also higher proton conductivity. The physical characteristics of these manufactured nanocomposite membranes were investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), water uptake, methanol permeability and ion exchange capacity, as well as proton conductivity. The Nafion®/MWCNT-Im membranes showed higher proton conductivity, lower methanol permeability and, as a consequence, a higher selectivity parameter in comparison to neat Nafion® or Nafion® containing –OH functionalized multi-walled carbon nanotubes (MWCNT-OH) membranes. The obtained results indicated that the Nafion®/MWCNT-Im membranes could be utilized as efficient polyelectrolyte membranes for direct methanol fuel cell applications.     

单壁碳纳米管弹性性质的羟基接枝效应

用分子动力学方法研究了端口接枝不同数量羟基对扶手椅型和锯齿型单壁碳纳米管弹性模量的影响.结果表明,未接枝的扶手椅型(5, 5),(10,10)管和锯齿型(9, 0),(18, 0)管杨氏模量分别为948,901和804,860GPa.在接枝2—8个羟基情况下,锯齿型单壁碳纳米管拉伸杨氏模量基本不随接枝数量增加发生变化,而扶手椅单壁碳纳米管则不同,接枝状态下的弹性模量比未接枝状态小很多,但接枝一定数量后,其杨氏模量又略增到某一稳定值.分别从接枝后碳纳米管变形电子密度等值线结构、C—C键长和系统结合能变化规律等方面,对单壁碳纳米管弹性模量的接枝效应进行了分析. 关键词： 碳纳米管 羟基 接枝效应 杨氏模量     

Electrical conduction mechanism in Fe<Subscript>70</Subscript>Pd<Subscript>30</Subscript> catalyzed multi-walled carbon nanotubes

Carbon nanotubes (CNTs) are synthesized by the catalytic decomposition of acetylene using low pressure chemical vapour deposition method (LPCVD) at 800 °C and at a chamber pressure of 10 Torr over a supported catalyst film of Fe₇₀Pd₃₀. Morphology of these CNTs is studied using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HRTEM). From HRTEM image of these multi-walled carbon nanotubes (MWNTs), it is clear that these MWNTs do not possess a co-axial cylindrical structure, but are composed of imperfect and broken graphite cylinders of different sizes. The average diameter and length of the nanotubes varies between 20–70 nm and 5–60 μm respectively. Electrical transport measurements of these MWNTs are studied over a temperature range of 298–4.2 K. The results have been interpreted in terms of variable-range hopping (VRH) over the entire temperature range of 298–4.2 K. Three-dimensional variable-range hopping (VRH) is suggested for the temperature range (298–125 K), while two-dimensional VRH is observed for the temperature range (125–4.2 K).     

Revealing distortion of carbon nanotube walls via angle-resolved X-ray spectroscopy

Arrays of aligned single-walled carbon nanotubes (SWCNTs) produced by supergrowth method were studied by scanning electron microscopy (SEM) and angle-resolved near-edge X-ray absorption fine structure spectroscopy, which defined that nanotube disorder is 10–13° and 23–27°, respectively. The latter value was confirmed by X-ray fluorescent spectroscopy. The difference in the obtained angular deviations was attributed to distortion of the SWCNT walls, because the X-ray spectroscopy methods are sensitive to a local environment of probing atoms, while the SEM examines the nanotubes at a substantially larger length scale. Significant distortion (20–24°) of SWCNT walls could be related to the defects introduced during the growth process.     

Electrical, dielectric and surface wetting properties of multi-walled carbon nanotubes/nylon-6 nanocomposites

This paper reports that the multi-walled carbon nanotubes(MWCNT)/nylon-6 (PA6) nanocomposites with different MWCNT loadingshave been prepared by a simple melt-compounding method. Theelectrical, dielectric, and surface wetting properties of theCNT/PA6 composites have been studied. The temperature dependence ofthe conductivity of the CNT/PA6 composite with 10.0 wt{\%} CNTloading ($\sigma _{\rm RT} \sim 10^{-4}$ S/cm) are measured, andafterwards a charge-energy-limited tunnelling model (ln $\sigma (T)\sim T^{-1/2})$ is found. With increasing CNT weight percentage from0.0 to 10.0 wt%, the dielectric constant of the CNT/PA6composites enhances and the dielectric loss tangent increases twoorders of magnitude. In addition, water contact angles of theCNT/PA6 composites increase and the composites with CNT loadinglarger than 2.0 wt%even become hydrophobic. The obtainedresults indicate that the electrical and surface properties of thecomposites have been significantly enhanced by the embedded carbonnanotubes.     

Experimental study on enhanced heat transfer of nanocomposite phase change materials

Nanocomposite phase change materials (NCPCMs) containing different mass fractions (nanomaterial concentration) and different copper nanoparticle (CN)/multi-walled carbon nanotubes (MWCNT) mass ratios were prepared and experimentally studied. Latent heat and thermal conductivity of the NCPCMs were studied and calculated by using the T-history method. The results revealed that addition of CN or MWCNT to the phase change material (PCM) resulted in NCPCMs with enhanced thermal conductivity and charge rates, respectively. However, when both nanoparticle materials were added to the PCM simultaneously, the resulting NCPCMs improved their thermal performance below expectations as a result of agglomeration and sedimentation between the two additives. Thus, the NCPCMs containing only CN or MWCNT showed superior thermophysical properties than the pure PCM, while the NCPCM containing both CN and MWCNT did not improve the thermal characteristic of PCM significantly.     

基于碳纳米薄膜/砷化镓范德华异质结的高性能自驱动光电探测器研究

基于碳纳米材料/体半导体范德华(vdW)异质结的光电器件可以同时实现碳纳米材料的超高载流子迁移率以及体半导体的优异光电性能,且具有结构简单、工艺简便、易于调控界面等优点.尤其是通过调控单壁碳纳米管(SWCNT)的直径/手性、费米能级等可以与体半导体形成能带匹配、具有原子级界面的新型混合维度vdW异质结.本文报道了一种基...     

固体单相催化剂CVD法制备成束或分散MWCNT*

CVD法制备纳米碳管的催化剂多是以Al2 O3、SiO2 或MgO作载体 ,Fe、Ni或Co等过渡族金属为活性组分[1- 3] .催化剂与载体之间的关系存在多种形式[1] ,其中固溶体催化剂[4 ,5] 使过渡金属离子能均匀地分布在载体的内部和表面 .在后续反应过程中 ,均匀分布在表面或体内的金属离子被还原成具有催化活性的金属微粒 .此法称为“原位催化分解法 (insituCVD法 )” ,常用于制备直径分布较为均匀的纳米碳管 ,但以往的这些固溶体催化剂在制备纳米碳管的产量上并没有明显的改善 .本工作报道用燃烧法制备的Fe Mo Mg O固溶体 ,不但在用于CVD法生长…     

170keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响

碳纳米管具有优异的导电性, 是未来电子元器件的理想候选材料, 应用前景广阔. 针对碳纳米管在空间电子元器件的应用需求, 本文研究了170 keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响. 采用扫描电子显微镜(SEM)、拉曼光谱仪(Raman)、X射线光电子能谱仪(XPS)及电子顺磁共振谱仪(EPR)对辐照前后碳纳米管试样的表面形貌和微观结构进行分析; 利用四探针测试仪对碳纳米管薄膜进行导电性能分析. SEM分析表明, 170 keV质子辐照条件下, 当辐照注量高于5×10¹⁵ p/cm² (protons/cm²)时, 碳纳米管薄膜表面变得粗糙疏松, 纳米管发生明显弯曲、收缩及相互缠结现象. 目前, 质子辐照纳米管发生的收缩现象被首次发现. 基于Raman和XPS分析表明, 170 keV质子辐照后碳纳米管的有序结构得到改善, 且随辐照注量增加, 碳纳米管的有序结构改善明显. 结构的改善主要是由于170 keV质子辐照碳纳米管所产生的位移效应导致缺陷重组. EPR分析表明, 随着辐照注量的增加, 碳纳米管薄膜内的非局域化电子减少. 利用四探针测试分析表明, 碳纳米管薄膜的导电性能变差, 这是由于170 keV质子辐照导致碳纳米管薄膜中的电子特性及形态发生改变. 本文研究结果有助于利用质子辐照对碳纳米管膜结构和性能进行调整, 从而制备出抗辐射的纳米电子器件.     

Electrochemical and surface characterisation of gold nanoparticle decorated multi-walled carbon nanotubes

A novel type of gold nanoparticle/multi-walled carbon nanotube (AuNP/MWCNT) composite electrodes is presented. The electrochemical reduction of oxygen on these hybrid electrodes was studied using the rotating disk electrode (RDE) method. The AuNP/MWCNT nanocomposites were prepared by sputter deposition of gold in argon atmosphere on MWCNTs followed by heat-treatment of the catalyst at different temperatures. High-resolution scanning electron microscopy (HR-SEM), glancing incidence angle X-ray powder diffraction (GIXRD) and small-angle X-ray scattering (SAXS) techniques were employed to characterise the surface structure and morphology of catalyst materials. Au nanoparticles with diameter around 20 nm were dispersed at the tips and on the sidewalls of nanotubes. Electrochemical measurements were performed to demonstrate the electrocatalytic properties of the composite catalysts towards O₂ reduction in acid media. The successful preparation of AuNP/MWCNT nanocomposites by magnetron sputtering opens up the possibility of making an efficient dispersion of nanoparticles for electrocatalyst design.