A potentiometric sensor for determining E133 dye in beverages

An ion-selective potentiometric sensor with an ionophore is developed based on the ion associate of artificial food colorant E133 and a cetylpyridinium cation. The main electroanalytical parameters of the sensor are evaluated: linearity range of the response, pH effect, and the effect of temperature on the electrode performance and selectivity. The sensor is used to determine E133 in the Powerade beverage. The accuracy of the determination is confirmed by an extraction–photometric method.     

A polymer membrane potentiometric sensor for silver

Four new sulfur-containing compounds based on pyridine, benzene, 1,8-naphthyridine and 1,10-phenanthroline have been synthesized. These molecules have been incorporated into a polymeric matrix as neutral carriers and evaluated as silver sensors. Two of the compounds (pyridine and benzene) show high selectivity for Ag(+). The sensor with the pyridine-based compound, in particular, shows near-Nernstian response and good sensitivity towards Ag(+) with a short response time (<10s), making it ideal for use in flow analysis.     

A potentiometric sensor for the determination of diclofenac

A diclofenacselective electrode with a plasticized poly(vinyl chloride) membrane containing an ion associate of diclofenac with Astrafloxin FF as an electrode-active substance was developed. The linearity range of the electrode function varied from 5 × 10^?5 to 5 × 10^?2 M; the slope of the electrode function was 59.0 ± 1.2 mV/pc, and the working pH range was 9–12. The effectiveness of the use of this electrode for monitoring diclofenac in pharmaceutical preparations was demonstrated.     

A novel, sensitive potentiometric hydrocarbon sensor for high-vacuum applications

A potentiometric device based on interfacing a solid electrolyte oxygen ion conductor with a thin platinum film acts as a robust, reproducible sensor for the detection of hydrocarbons in high- or ultrahigh-vacuum environments. Sensitivities in the order of approximately 5 x 10(-10) mbar are achievable under open circuit conditions, with good selectivity for discrimination between n-butane on one hand and toluene, n-octane, n-hexane, and 1-butene on the other hand. The sensor's sensitivity may be tuned by operating under constant current (closed circuit) conditions; injection of anodic current is also a very effective means of restoring a clean sensing surface at any desired point. XPS data and potentiometric measurements confirm the proposed mode of sensing action: the steady-state coverage of Oa, which sets the potential of the Pt sensing electrode, is determined by the partial pressure and dissociative sticking probability of the impinging hydrocarbon. The principles established here provide the basis for a viable, inherently flexible, and promising means for the sensitive and selective detection of hydrocarbons under demanding conditions.     

A novel ferroin membrane sensor for potentiometric determination of iron

A novel potentiometric approach for both batch and flow injection determination of iron(II) and/or iron(III) is described. It is based on the formation and monitoring of ferroin with a PVC membrane sensor containing ferroin-TPB as an electroactive component plasticized with 2-nitrophenyl phenyl ether. The sensor exhibits fast Nernstian response for ferroin with a cationic calibration slope of 30 +/- 0.2 mV/concentration decade down to 4 x 10(-7)M ferroin (0.03 ppm Fe) at pH 3-9. Interferences from common inorganic cations are negligible or can be eliminated by a pretreatment with DDC. The ferroin sensor was successfully applied to the determination of iron contents in water, alloys, rocks and pharmaceuticals. The results show good correlation with data obtained by the standard spectrophotometric ferroin method, the coefficient of correlation is better than 0.7%.     

A ferrocene-modified platinum electrode as a potentiometric sensor for l-ascorbic acid

A half-oxidized platinum electrode modified with a monolayer of ferrocene is proposed as a potentiometric sensor for l-ascorbic acid in an aqueous glycine buffer pH 2.2. The ferrocene was covalently attached to the surface by a silane carbon chain. The potentials of 15 electrodes were measured and a slope of (50 ± 8.8) mV per decade change in concentration of ascorbic acid was obtained over the concentration range 10^?3-10^?6 M. Recovery experiments with pure l-ascorbic acid solutions showed a relative standard deviation of 1.9%, in the analysis of fresh orange juice, the relative standard deviation was 6.1%.     

A novel uranyl membrane sensor with potentiometric anionic response

A novel potentiometric uranyl membrane sensor with a divalent anionic response is developed, characterized and used for determination of uranyl ion. The sensor incorporates triethylenetetramine (TETA) as an ionophore in poly(vinyl chloride) matrix membrane (PVC) plasticized with o-nitrophenyloctyl ether (o-NPOE). In strong sulphate test solutions, UO₂²⁺ ion forms a highly stable [UO₂(SO₄)₂]²⁻ anion, extractable in TETA as {(2TETAH)²⁺ [UO₂(SO₄)₂]²⁻} complex. Formation of the complex is confirmed and characterized by elemental analysis, mass spectrometry and infrared spectrometry. Sensor based on this system displays at pH 2.5-3.8 a linear response over the concentration range of 1.0 × 10⁻¹-3.5 × 10⁻⁵ mol l⁻¹ uranium with a near-Nernstian calibration slope of −26.5 ± 0.3 mV decade⁻¹. The lower limit of detection is ∼5 μg ml⁻¹, the lifetime is 12 weeks and negligible interferences are caused by most common cations. Validation of the assay method reveals excellent performance characteristics in terms of sensitivity, selectivity, fast response and potential stability. The sensor is used for the determination of 0.01-7.09 wt% uranium in naturally occurring and certified ore samples. The results show an average recovery of 97.6% and compare fairly well with data obtained using X-ray fluorescence technique.     

Polymeric membrane sensor for potentiometric determination of vanadyl ions

In this research, new electrodes were prepared by incorporating a new calix[4]arene derivative into a plasticized poly(vinyl chloride) matrix. Calibration plots with Nernstian slopes (29.9 ± 1.1 mV/decade) for vanadyl ion were observed over a linear range of about four decades of concentration (1.0 × 10⁻⁵ to 1.0 × 10⁻¹ mol dm⁻³, at 25 °C). This electrode revealed a lower limit of detection of 3.9 × 10⁻⁶ mol dm⁻³. Conductometric data showed the relatively strong interaction between calix[4]arene and vanadyl ions. The results show that this electrode can be used in acetonitril and methanol media until 10% (v/v) concentration without interference. It has a short response time and can be used for more than two months without any considerable divergence in the potentials. The influence of membrane composition, the pH of the test solution, and the interfering ions on the electrode performance was investigated. The effect of temperature on the electrode response showed that the temperature higher than 50 °C deteriorates the electrode performance. The isothermal temperature coefficient of this electrode amounted to 0.0015 V °C⁻¹. The results of application show that the electrode can be used successfully in present Cr³⁺ and Fe³⁺.     

Flow injection potentiometric sensor for determination of phenylpropanolamine hydrochloride

A new polymeric membrane electrode has been constructed for the determination of phenylpropanolamine hydrochloride. The electrode was prepared by solubilizing the phenylpropanolamine-phosphomolybdate ion associate into a polyvinyl chloride matrix plasticized by dibutylphthalate as a solvent mediator. The electrode showed near-Nernstian response over the concentration range of 1 × 10^?5–1 × 10^?2 M with low detection limit of 6.3 × 10^?6 M. The electrode displays a good selectivity for phenylpropanolamine with respect to a number of common inorganic and organic species. The electrode was successfully applied to the potentiometric determination of phenylpropanolamine ion in its pure state and its pharmaceutical preparation in batch and flow injection conditions.     

PVC matrix membrane sensor for potentiometric determination of dodecylsulfate

The construction and performance characteristics of a new potentiometric PVC membrane sensor for the determination of sodium dodecyl sulfate (SDS) are described. The sensor was based on the use of an N-cetyl-N,N,N trimethyl ammonium (CTA) dodecyl sulfate (DS) ion pair as ion exchange sites in PVC matrix in the presence of o-nitrophenyl octylether as plasticiser. The sensor exhibited a fast, stable, and near-Nernstian response for SDS over the concentration range of 1 × 10^?3 to 10^?6 M at 25°C and the pH range 4–8.5 with anionic slope of 52.5 ± 0.5 mV decade^?1. The lower detection limit was 3 × 10^?6 M, and the response time was 25 s. Selectivity coefficients of SDS with respect to a number of different species were investigated. There were negligible interferences caused by most of the investigated anions. The determination of 1.0–280.0 µg mL^?1 of SDS in aqueous solutions showed an average recovery of 99.1%, and the mean relative standard deviation was 1.4 at 100 µg mL^?1. The results obtained in the determination of SDS in liquid soap, water and in some pharmaceutical preparations compared favourably with those obtained by the Methylene Blue active substance method (MBAS). In the present investigation, the DS sensor has been used as an end-point indicator electrode for some precipitation titration reactions, e.g. titration of SDS with CTMABr and cetylpyridinium chloride with SDS.     

A chemometric sensor for determining sulphaguanidine residues in honey samples

The inclusion complex of sulphaguanidine (SGN) in β-cyclodextrin has been investigated. To avoid the problem of the low solubility of β-cyclodextrin in water, solutions of β-cyclodextrin in urea have been used. A 1:1 stoichiometry and an association constant of 450 M⁻¹ have been established for the complex. A new spectrofluorimetric method has been developed for the determination of SGN residues in honey samples. This sulphonamide is widely employed for honey treatment. The method for the determination is based on second-order multivariate calibration, applying parallel factor analysis (PARAFAC). No previous separation or samples pre-treatment were required. The calibration solutions were prepared in water, with concentrations in the range from 0.02 to 0.20 μg mL⁻¹ for SGN. The use of the second-order calibration method in the standard addition mode, using the excitation-emission matrices (EEMs) as analytical signal, allowed its determination in honey samples, even in the presence of interferences, with satisfactory results. The proposed procedure was validated by comparing the obtained results with a HPLC method, with satisfactory results for the assayed method.     

Disposable potentiometric enzyme sensor for direct determination of organophosphorus insecticides

A potentiometric disposable enzyme sensor for the direct and fast determination of organophosphorus (OP) insecticides was developed by using an organophosphorus hydrolase (OPH) immobilized on an ion-selective electrode. The disposable screen-printed transducer was based on double matrix membrane technology which allows easy mass production. The potentiometric device consisted of a H(+)-sensitive electrode with integrated Ag/AgCl reference electrode. The electrodes were prepared with N,N-dioctadecylmethylamine as H(+)-sensitive ionophore and pH calibration resulted in slopes of 55 mV decade-1 over a pH range from 11 to 6. OPH was isolated from recombinant Escherichia coli DH5 alpha and immobilized within poly(carbamoyl sulfonate) prepolymer on the surface of the H(+)-sensitive electrode without any further fixation membrane. OPH catalyzes the hydrolytic cleavage of OP compounds which releases protons in a concentration proportional to hydrolyzed substrate. Sensor performance was investigated with regard to enzyme load, concentration, pH and temperature of the measuring buffer using paraoxon as analyte. Best sensitivity and response time were obtained with sensors prepared with 250 U of OPH and measuring at 37 degrees C in 1.0 mM HEPES buffer, pH 9.3, containing 100 mM NaCl. The enzyme sensor exhibited a linear calibration range of 0.01-0.15 mM chlorpyrifos, 0.05-0.35 mM diazinon, 0.05-0.4 mM paraoxon and 0.007-0.05 mM parathion, respectively. For all these analytes response times to reach 95% of maximum change in potential did not exceed 5 min. Sensors stored under dry conditions at 4 degrees C still showed 60% of initial hydrolytic rate after 70 d. The sensors even when stored dry were ready for measurements after 5 min incubation in measuring buffer. A range of putative interfering substances did not influence sensor response, and suitability of measuring OPs in soil extracts was ascertained.     

Recent trends in potentiometric sensor arrays--a review

Nowadays there exists a large variety of ion sensors based on polymeric or solid-state membranes that can be used in a sensor array format in many analytical applications. This review aims at providing a critical overview of the distinct approaches that were developed to build and use potentiometric sensor arrays based on different transduction principles, such as classical ion-selective electrodes (ISEs) with polymer or solid-state membranes, solid-contact electrodes (SCE) including coated wire electrodes (CWE), ion-sensitive field-effect transistors (ISFETs) and light addressable potentiometric sensors (LAPS). Analysing latest publications on potentiometric sensor arrays development and applications certain problems are outlined and trends are discussed.     

Measurement of pork freshness using potentiometric sensor

This study evaluated pork freshness using potentiometric solid-state electrodes in order to detect chemical indices such as reduced compounds, organic compounds and sulfides, which are produced during the initial stage of putrefaction in meat. Pt, CuS and Ag₂S electrodes selected as solid-state electrodes have, respectively, been used to detect the organic compounds (regarded as chemical indices of deterioration in meat freshness). The outputs of these electrodes have been analyzed by principal component analysis (PCA) and multiple regression analysis (MRA) in order to find the correlation with the results of viable bacterial counts. By using the potentiometric sensor, the pork freshness was evaluated and the PCA and MRA corresponded to the degree of bacterial increases more simply and rapidly than other methods such as viable bacterial counts or a biosensor.     

A PVC-based pentathia-15-crown-5 membrane potentiometric sensor for mercury(II)

Poly(vinyl chloride) (PVC)-based membrane of pentathia-15-crown-5 exhibits good potentiometric response for Hg²⁺ over a wide concentration range (2.51 × 10⁻⁵ to 1.00 × 10⁻¹ mol dm⁻³) with a slope of 32.1 mV per decade of Hg²⁺ concentration. The response time of the sensor is as fast as 20 s. The electrode has been used for a period of six weeks and exhibits fairly good discriminating ability towards Hg²⁺ in comparison to alkali, alkaline and some heavy metal ions. The electrode can be used in the pH range from 2.7 to 5.0.     

A potentiometric microbial sensor based on immobilized escherichia coli for glutamic acid

The sensor consists of immobilized E. coli (which contains glutamate decarboxylase) and a carbon dioxide gas-sensor. Continuous introduction of sample solution into a flow system incorporating the sensor gives a potential which increases until a steady state is reached after 5 min. Measurements can also be made with only a 1- or 3-min introduction period with little loss of sensitivity. Calibration plots of mV measurements vs. logarithmic glutamic acid concentration are linear in the range 100–800 mg l^-1. The sensor is highly selective, stable and reproducible. It has been applied to the determination of glutamic acid in fermentation broths.     

A potentiometric multisensor system for determining lysine in aqueous solutions containing potassium and sodium chloride

A potentiometric multisensor system has been developed for the determination of lysine in aqueous solutions containing sodium and potassium chlorides. The sensor array includes a cross-sensitive sensor, the response of which is the Donnan potential at the ion-exchange polymer/test solution interface, a set of ion-selective electrodes, and a silver-silver chloride reference electrode. Multidimensional regression analysis has been employed for the calculation of component concentrations. The relative error of determining lysine, potassium, and sodium did exceed 10% in the tested solutions.     

PVC matrix membrane sensor for potentiometric determination of cetylpyridinium chloride.

A novel cetylpyridinium chloride-selective membrane sensor consisting of cetylpyridinium-ferric thiocyanate ion pairs dispersed in a PVC matrix placticized with dioctylphthalate is described. The electrode shows a stable, near-Nernstian response for 1 x 10(-3)-1 x 10(-6) mol l-1 cetylpyridinium chloride (CPC) at 25 degrees C over the pH range 1-6 with a cationic slope of 57.5 +/- 0.4. The lower detection limit is 8 x 10(-7) mol l-1 and the response time is 30-60 s. Selectivity coefficients for CPC relative to a number of interfering substances were investigated. There is negligible interference from many cations, anions and pharmaceutical excipients; however, cetyltrimethylammonim bromide (CTMAB) interfered significantly. The determination of 0.5-350 micrograms/ml of CPC in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 56.0 micrograms/ml. The direct determination of CPC in Ezafluor mouthwash gave results that compare favorably with those obtained by the British Pharmacopoeia method. Precipitation titrations involving CPC as titrant are monitored with a CP sensor. The CP electrode has been utilized as an end point indicator electrode for the determination of anionic surfactants in some commercial detergents.     

A PVC-based cryptand C2B22 membrane potentiometric sensor for zinc(II)

A PVC membrane electrode for zinc ions based on cryptand C2_B22 as membrane carrier was prepared. The electrode exhibits a linear stable response over a wide concentration range (5.0 × 10^–2– 5.0 × 10^–5 mol/L) with a slope of 24 mV/ decade and a limit of detection of 3.98 × 10^–5 mol/L (2.6 μg/g). It has a fast response time of about 30 s and can be used for at least 4 months without any divergence in potential. The proposed sensor revealed good selectivities for Zn²⁺ over a wide variety of other metal ions and could be used in a pH range of 4–7. It was used as an indicator electrode in potentiometric titration of zinc ion. Received: 26 February 1998 / Revised: 25 May 1998 / Accepted: 28 May 1998     

Liquid membrane potentiometric sensor for determination of Fe3+ ion

Solution studies showed a selective interaction between the new synthesized ionophore, 2-[(thiophen-2-yl)methyleneamino]isoindoline-1,3-dione (TMID) and Fe(III) ion. Therefore, TMID was used as an iron selective ion-carrier in a plasticized liquid membrane sensor. The linear response range of the proposed electrode was 1.0 × 10^?6–1.0 × 10^?2 M. The Nernstian slope of 20.1 ± 0.3 mV/decade, and a detection limit of 5 × 10^?7 M was obtained. The sensor could be used in the pH range of 2.3–4.8, and the response time was about 10 s. The lifetime of the electrode was at least 7 weeks. The sensor accuracy was investigated in two ways: (i) with the potentiometric titration of a Fe³⁺ solution with EDTA and (ii) with Fe(III) monitoring in some cationic mixtures. Finally, the newly fabricated electrode was effectively applied as an indicator electrode for the direct Fe³⁺ determination in real samples.