粒度分析及粒度标准物质研究进展

综述了当前粒度分析测试方法的研究进展,并简单介绍了各种测试方法的基本原理以及包括美国、欧洲、中国在内的国家和地区在粒度标准物质方面的研究概况。     

Thermal Behaviour of Some Terpenoids

The terpenoids acetyl sitosterol, lupeol, acetyl diosgenin and stigmasterol were studied. Comparison of the thermogravimetric curves and the activation energies of the terpenoids suggested the following sequence of thermal stability: acetyl sitosterol < acetyl diosgenin < lupeol < stigmasterol. The DSC curves allowed determination of the melting points and the degrees of purity. Comparison of the TG and DSC curves revealed the presence of phase transitions without mass loss that were attributed to rearrangements in the terpenoid molecules. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal Behaviour and Adsorption Properties of Natural Stilbite

Crystals collected from the Ellora valley(Aurangabad, MS, India) of the Deccan traps of India have beencharacterized as a stilbite (St) by X-ray diffraction, IRspectroscopy and chemical analyses. The thermal behaviour was studiedusing TG and DTA techniques. The sample was exchanged at refluxtemperature with NH4Cl and NH4St was prepared. This was furthertransformed to the H-form of stilbite (HSt) by heating at 573 K for 12 h.The samples so prepared were used for adsorption studies. The comparativestudy of sorption of these samples shows an increase in the sorptioncapacity of HSt. The isosteric heat was also computed for these samples.     

Effect of Processing and Aging on Particle Size of Explosives

Influence of such processes as molding powder production, pel-lets pressing and aging under different condit/ons on particle size of TATB ( 1,3,S-trlamino-2,4,6-trinltrobenzene ) and HMX (cyclotetramethylenetetranitramine) was experimentally studied. The results showed that parflele size of these explosives was greatly changed before and airier moldinu powder produc-tion, but for different size grade of explosive this change was not the same; pressing process had also great effect on explosive particle size, but before and after ageing process explosive par-tide size did not change seriously.     

Pozzolanic properties of a residual FCC catalyst during the early stages of cement hydration

The catalyst used in fluidized catalytic cracking (FCC) units of refineries after several recovery cycles in regeneration units, reduces its activity and it is partially substituted by new catalyst in the process. As it has a high silicon and aluminum oxides content, the pozzolanic properties of a Brazilian FCC spent residual catalyst, used in different substitution degrees to cement, were evaluated by three thermal analysis techniques during the early stages of hydration of a type II Portland cement. NCDTA curves show in real time that the residual catalyst, accelerates the stages of cement hydration. TG and DSC curves of respective pastes after 24 h of hydration evidence the pozzolanic activity of the waste, respectively, by the lower water mass loss during the dehydroxylation of the residual calcium hydroxide and by the lower dehydroxylation endothermal effect. Within the analyzed period, the higher is the cement substitution degree, the higher is the pozzolanic activity of the residual catalyst.     

乙酸对阳离子型PVAc乳液粒径的影响

以醋酸乙烯酯(VAc)和甲基丙烯酰氧基乙基三甲基氯化铵为主单体,Gemini超支化双子型阳离子表面活性剂和OP-10为复合乳化剂,通过乳液聚合制得一系列阳离子型聚醋酸乙烯酯乳液(1n),考察了VAc的主要杂质乙酸对1n粒径的影响.研究结果表明,乙酸含量增多时,Gemini超支化阳离子表面活性剂的临界胶束浓度和表面张力都...     

Effect of Variant Counterions on Stability and Particle Size of Silica Sol

The effects of variant counterions with ionic strength of 0.05, 0.10, 0.20 and 0.25 mol·kg^-1 on the stability and particle size of silica sols have been studied using the traditional methods of Ubbelohde viscosity measurement, TEM and titration respectively, finding that the stability and particle size of the silica sols are all concerned with the acidic, positively electric properties and the sizes of the counterions, as well as the attraction between the counterions and surface silicon hydroxyl groups of the silica sols. The small positively charged counterions lead to the decrease in particle sizes, making the silica sol the most stable. But the larger weakly acidic counterions can restrict the particle sizes of the silica sols and easily make the sols coagulate. It was also found that there existed a linear relationship between log r and log η, which has not ever been reported. The effect of temperature on the stability and particle sizes was also discussed.     

分散剂类型对聚苯胺粒径分布和电化学特性的影响

采用化学氧化聚合法以苯胺为单体、过硫酸铵为氧化剂,在不同分散剂体系中合成聚苯胺,考察分散剂对聚苯胺性能的影响。通过激光粒度仪、傅里叶红外吸收光谱、四探针电阻仪和电化学工作站等测试手段研究聚苯胺的结构、导电性、粒径分布及电化学性能。结果表明：分散剂能降低聚苯胺的粒径分布,提高聚苯胺的导电性和电化学稳定性;当分散剂聚乙二醇占苯胺单体质量的20％时,聚苯胺的平均粒径为3．85μm,导电率为4．68S／cm,极化电位为0．73V。     

Insight into the Effect of ZIF-8 Particle Size on the Performance in Nanocarbon-Based Supercapacitors

Carbon materials derived from zeolitic imidazolate framework-8 (ZIF-8) and composites thereof have been intensively investigated in supercapacitors. The particle size of the used ZIF-8 ranges from dozens of nanometers to several microns. However, the influence of the particle size of ZIF-8 on the capacitive performances is still not clear. A series of ZIF-8 with different particle sizes (from 25 to 296 nm) has been synthesized and carbonized for supercapacitors. Based on TEM, EDX mapping, XRD, Raman, nitrogen adsorption–desorption, XPS, and the results of electrochemical tests, the optimal particle size (≈70 nm) for superior supercapacitor performances in both acidic and alkaline electrolytes has been obtained. This important result provides a significant reference to guide future ZIF-8 related research to achieve the best electrochemical performance.     

Coupled Single‐Particle and Population Balance Modeling for Particle Size Distribution of Poly(propylene) Produced in Loop Reactors

A comprehensive model was developed for the PSD of PP produced in loop reactors. The polymeric multilayer model (PMLM) was first applied to calculate the single particle growth rate under intraparticle transfer limitations. In order to obtain the comprehensive model, the PMLM was solved together with a steady‐state particle population equation to predict the PSD in the loop reactors. The simulated PSD data obtained under steady‐state polymerization conditions agreed with the actual data collected from industrial scale plant. The comprehensive model was also used to predict the effects of some critical factors, including the intraparticle mass and heat transfer limitations, the feed catalyst particle size and the catalyst deactivation, etc., on the PSD.

     

Effect of sulfadiazine on biological model membranes

Summary In this paper the optimization of the kaolin calcination is studied, aiming at using the produced metakaolin as supplementary cementitious material. Representative samples of poor Greek kaolin (Milos island) and a high purity commercial kaolin were tested. Samples were heated at different temperatures during different times. The optimization of calcination conditions was studied by DTA-TG and XRD analysis of the raw and thermal treated kaolin samples, by pozzolanic activity analysis of metakaolins and finally by strength development analysis of cement-metakaolin mixtures. This approach showed that heating at 650°C for 3 h is efficient to convert poor kaolins with low alunite content to highly reactive metakaolins. However in the case of kaolin with a high alunite content, thermal treatment at 850°C for 3 h is required in order to remove undesirable SO₃. Evidence was found that poor kaolins can be efficiently used for the production of highly reactive metakaolins.     

水滑石晶体长厚比及晶粒尺寸控制方法研究

层状双金属氢氧化物（LayeredDoubleHydrox－ides，简称LDH）是一类重要的无机晶体材料，因其具有层状结构以及层板元素的可调控性和层间阴离子的可交换性，在催化、离子交换、吸附、医药犤１～８犦等方面具有广泛的用途，已受到人们越来越广泛的关注。近年来，随该类材料应用领域的不断拓展，在许多情况下要求LDH晶体具有小的粒径尺寸，以便最大限度地发挥其功能性。例如将LDH作为阻燃剂犤９犦使用，小粒径粉体可增强与聚合物基材的相容性，提高材料的阻燃、抑烟和力学性能。另一方面，因LDH具有层状结构，在复合材料中其层板能有效…     

Maximum Achievable Particle Size in Emulsion Polymerization: Modeling of Large Particle Sizes

A simplified model for particle formation in emulsion polymerization (comprising aqueous‐phase propagation to degrees of polymerization which may enter a pre‐existing particle and/or form new particles by homogeneous or micellar nucleation, coupled with the aqueous‐phase and intra‐particle kinetics of oligomeric radicals) is formulated to provide a model suitable for the simulation of systems containing large‐sized particles. The model is particularly useful to explore conditions for growth of large particles while avoiding secondary particle formation. Applied to the Interval II emulsion polymerization of styrene with persulfate initiator at 50°C, it is found that there is an effective maximum particle size that can be achieved if the formation of new particles is to be avoided. The parameter space of initiator concentration, particle number concentration and particle radius is mapped to show a “catastrophe” surface at the onset of new nucleation. Advanced visualization techniques are used to interpret the large number of simulations in the series, showing a maximum achievable particle diameter of around 5 μm.     

漆酶在纳米金溶胶/多重壁碳纳米管复合载体上固定方法的比较及粒子尺寸效应

以纳米金溶胶（NGS）和多重壁碳纳米管（MWCNTs）的共混物(NGS/MWCNTs)作为固定漆酶的载体,研究了3种固定漆酶方法在酶固定量、比活力上的差异。 研究了不同的固定方法对固定酶热稳定性和重复使用性及纳米金溶胶颗粒粒径对酶固定量和固定酶动力学参数的影响。 实验结果表明,NGS/MWCNTs具有良好的固定漆酶能力和高固酶比活力,NGS/MWCNTs（NGS粒径37 nm）通过简单物理吸附法固定漆酶的量和固酶的比活力最高,分别可达33.80 mg/g和9.433 U/mg。 在NGS-MWCNTs上采用化学键合方法固定的漆酶在70 ℃放置2 h后仍然保持初始活力的75％,重复使用20次后仍保持初始活力的70％。 纳米金溶胶粒子越小（24 nm）,底物和固定漆酶间亲和力越好（KM=0.027 mmol/L）,表观速率常数越大。     

Pt/C催化剂对甲酸电催化氧化的粒径效应

在甲醇溶剂中,利用SnCl2作为还原剂,通过控制反应条件制备了具有不同粒径Pt粒子的炭载Pt(Pt/C)催化剂.X射线衍射(XRD)和透射电子显微镜(TEM)的结果表明,Pt/C催化剂中Pt粒子具有高度的均一性和良好的分散度.电化学研究结果显示,对于甲酸的电催化氧化,Pt/C催化剂存在着明显的粒径效应.当Pt粒子粒径为3.2 nm时,Pt/C催化剂对甲酸的电催化氧化活性最佳.Pt/C催化剂对甲酸氧化的粒径效应与其表面含氧基团含量、Pt粒子的比表面积及相对结晶度相关.     

高岭土原位无溶剂法合成小粒径ZSM-5分子筛

结合原位水热法和无溶剂法的优点,在不添加有机模板剂和溶剂的基础上,以高岭土为原料通过晶种诱导绿色高效地合成出ZSM-5分子筛。运用X射线衍射、N2吸附-脱附、扫描电镜、透射电镜和NH3程序升温脱附(TPD-NH3)等技术对ZSM-5分子筛进行表征。表征结果与原位水热法合成的ZSM-5分子筛相比,原位无溶剂法合成ZSM-5分子筛的结晶度较高、晶体粒径较小、酸强度略高、孔结构相似。     

聚苯乙烯胶乳颗粒的成膜过程及尺寸效应

聚合物乳液成膜过程可分为介质蒸发、颗粒形变和相邻颗粒间高分子的扩散融合三个阶段.一般认为,环境温度达到或高于高分子的玻璃化转变温度(T_g)时颗粒才可能发生形变.Goudy等研究了粒径为0.24～1.05μm的聚苯乙烯(PS)胶乳的成膜过程,发现PS颗粒在368K(T_g约373K)热处理很长时间也不发生形变,而在378K热处理后,粒径较小的颗粒融合速度快于较大颗粒.     

制备单分散交联聚苯乙烯微球共聚合动力学和粒径的研究

粒子粒径分布;制备单分散交联聚苯乙烯微球共聚合动力学和粒径的研究     

4种激光粒度仪对下蜀土湿法粒度测试的对比研究

使用4种应用较为广泛的激光粒度仪(Mastersizer2000、Bettersize2000、Horiba LA950和LS13320)对粒度差异较小的下蜀土(土塘剖面)进行了测试,从而对比分析不同激光粒度仪对于下蜀土的粒度组成测试差异及其这种差异对研究结果可能产生的影响.结果表明:对粉砂颗粒组分的分析,4种激光粒度分析仪分析结果的差异最小,而对砂和粘土颗粒组分分析的差异最大.就粒度频数曲线、概率累积曲线、粒度组分、C-M图、粒度参数散点图及粒度参数剖面垂向变化等统计参数与统计方式而言,4种仪器的测试结果均有一定的差异,其中,概率累积曲线、粒度参数散点图差异较大.粒度参数的剖面变化差异也较大,影响了对剖面的阶段性划分,这在一定程度上影响了研究结果,造成使用不同仪器,可能会得出不同的结果.     

Effect of Different Composition on Particle Size Chitosan-PMAA-PNIPAM Hydrogel

Chitosan-based (chitosan-poly(methacrylic acid)-poly(N-isopropylacrylamide) [Cs-PMAA-PNIPAM] copolymer hydrogels were synthesized by free radical emulsion polymerization to study the effect of different composition of monomer on hydrogel particle size. Chitosan usually applied for medical use such as drug delivery due to its biodegradability, bio-compatibility, and non-toxicity properties. Co-polymerized chitosan with MAA and NIPAM is an improvement of chitosan gel to be more responsive to the environment of human body included different pH, temperature, ionic strength, electric field, and enzyme activities. Small size of the particles is particularly important to ensure the particles reach the target site especially as a drug delivery. A full factorial experimental design (2³) was employed to identify which factors influenced most on the particle size. The design considered three factors which is amount of MAA, NIPAM and N,N’-Methylenebisacrylamide (MBA) while particle size are chosen as the responses of the variation on each composition. Particle size distribution was measured by laser diffractionin wet condition. From the design of experiment, NIPAM shows the main factor affected the particle size. However combination of the others factors also contributed on the whole size of the hydrogel.