谐振载荷作用下工程结构振动疲劳寿命预估的损伤力学-有限元法

建立了预估谐振载荷作用下结构振动疲劳寿命的损伤力学-有限元方法。首先根据损伤热力学原理,构建了损伤演化方程,建立光滑试件在恒幅应变交变载荷作用下寿命预估方法;进一步由损伤力学守恒积分原理,得到恒幅重复载荷作用下应力与寿命的关系式;然后根据标准件疲劳试验结果,拟合得到损伤演化方程中的材质参数;最后利用APDL语言编程对ANSYS软件进行了二次开发,借助ANSYS软件对谐振载荷作用下结构振动疲劳裂纹萌生寿命进行预估。作为算例,本文利用该方法预估了LC9CgS1铝合金梁谐振载荷作用下疲劳裂纹萌生寿命。     

Fatigue life evaluation by weight functions for orthotropic bridge decks

This paper is concerned with the prediction of fatigue crack propagation in welded orthotropic decks for road and railway steel bridges. The analysis makes use of a weight function (WF), that provides effective evaluation of the stress intensity factor (SIF) for any crack length and loading condition. The WF was determined by a hybrid (numerical/analytical) technique and verified with numerical results. The fatigue life were estimated for different initial crack lengths and loading cycles. Endurance limits were obtained to establish in-service inspection schedule of the structure. The effect of weldment residual stress on the fatigue life was also analyzed. It was shown that the WF technique provides an expedient evaluation of these effects, also accounting for non-linear (contact) phenomena.     

STUDY ON THE SURFACE CRACK GROWTH BEHAVIOR IN 14MnNbq BRIDGE STEEL

Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are systematically conducted.The experimentally measured fatigue crack growth rates of surface cracks are compared with those of through-thickness cracks in detail.It is found that the crack growth rates of surface cracks are lower than those of through-thickness cracks.In order to correct their differences in fatigue crack growth rates, a dimensionless crack closure correction model is proposed.Although this correction model is determined only by the experimental data of surface cracks under tensile loading with a constant ratio R=0.05, it can correlate the surface crack growth rates with reasonable accuracy under tensile and bending loadings with various stress ratios ranging from 0 to 0.5.Furthermore, predictions of fatigue life and crack aspect ratio for surface cracks are discussed, and the predicted results are also compared with those obtained from other prediction approaches.Comparison results show that the proposed crack closure correction model gives better prediction of fatigue life than other models.     

Extended finite element method for fretting fatigue crack propagation

In this paper, the extended finite element method (X-FEM) is considered for the analysis of fretting fatigue problems. A two-dimensional implementation of the X-FEM is carried out within the finite element software ABAQUS? by means of user subroutines, and crack propagation in fretting fatigue problems is investigated. On utilizing the non-linear contact capabilities of this code, the numerical technique is applied to a specimen-indenter model. The use of the X-FEM facilitates very accurate stress intensity factor computations on relatively coarse meshes, and furthermore, no remeshing is required for crack growth simulations. The implementation is applied to complete and incomplete contact fretting problems. A study of crack growth is conducted for several bulk loads applied to the specimen, and the influence of the initial crack angle is ascertained. The numerical simulations reveal the merits of applying the X-FEM to fretting fatigue problems.     

Thermography Applied to the Study of Fatigue Crack Propagation in Polycarbonate

Thermography was used to study the propagation of fatigue cracks during cyclic loading of pre-cracked SAE keyhole polycarbonate specimens. A micro-bolometer infrared camera (FLIR A655sc) and a commercially available software program (DeltaTherm2) were employed. The stress intensity factors were determined using a hybrid thermoelastic stress analysis (TSA) technique. The crack growth rate was determined via thermography using two different approaches. The first approach used the output of the crack-tip position from the developed TSA algorithm and the number of cycles between data sets. The second approach used temperature measurement as a new way to determine da/dN (crack growth rate) directly. As a result, da/dN vs ΔK (stress intensity factor range) graphs were plotted and fitted using Paris’ law. A comparison between the resultant da/dN vs ΔK curves and results found in the literature, as well as curves from the finite element method (FEM) simulations showed good agreement. The conclusion was that thermography is a very powerful tool that can detect, measure and monitor fatigue cracks in polycarbonate.     

A model for predicting the retardation effect following a single overload

Many engineering components are subjected to variable amplitude loading history. It is well known that retardation in fatigue crack growth occurs due to application of single overloads in a constant amplitude loading block. Many models have been proposed to capture this counter intuitive phenomenon which has resulted in improved understanding of retardation effect following tensile overloads and consequently resulting in better life prediction models. The proposed study is focused on to evaluation of retardation in fatigue life due to application of a single overload. A model for prediction of crack growth and crack growth rate following single overloads is presented. Several modifications to Wheeler’s growth idea are proposed, which incorporate a consideration for effective stress intensity factor, based on Elber’s concept of crack closure, relationship between overload ratio and the Wheeler’s exponent, and fatigue growth rate calculations. The results presented here show that plastic zone interaction following overload and the consideration of crack closure explain retardation effect following a single overload. Correlation between analysis and experimental data obtained from several sources in literature show that the scheme, is robust and provides an insight into the nonlinear aspect of crack growth results. The model has been tested for 2024-T3 aluminum alloy and 6061-T6 aluminum alloy and thorough calibrations performed, established the fidelity of the program.     

巴西圆盘试样中心斜裂纹疲劳扩展轨迹的边界元模拟

提出了一个平面弹性体多裂纹疲劳扩展模型. 它主要涉及到复合型加载情况下多裂纹尖端疲劳扩展的数学模型及杂交位移不连续法(一种边界元法). 在数值模拟中, 对每一裂纹扩展增量分析时,在其先前的边界上增添裂纹扩展增量, 且只对新增添的裂纹扩展增量划分单元, 同时, 按照这种边界元法的实施方法对一些单元特征进行调整, 就可以方便地模拟裂纹扩展. 用这种数值方法模拟了巴西圆盘试样中心斜裂纹疲劳扩展轨迹,数值结果说明了预报模型的有效性, 揭示了裂纹体几何对疲劳扩展的影响.      

Fatigue crack growth behavior of Al7050-T7451 attachment lugs under flight spectrum variation

This paper discusses an analytical and experimental investigations of the fatigue crack growth behavior in attachment lugs subjected to a randomized flight-by-flight spectrum. In the analysis, the stress intensity factors for through-the-thickness cracks initiating from lug holes were compared by weight function method, boundary element method (BEM), the interpolation of Brussat’s solution. The stress intensity factors of a corner crack at a transition region were obtained using two parameter weight function method and correction factors. Fatigue life under a load spectrum was predicted using stress intensity factors and Willenborg retardation model considering the effects of a tensile overload. Experiments were performed under a load spectrum and compared with the fatigue life prediction using the stress intensity factors by different methods. Changes of fatigue life and aspect ratio according to the clipping level of the spectrum were discussed through experiment and prediction. Effect of the spectrum clipping level on the fatigue life was experimentally evaluated by using beach marks of fractured surface.     

Investigation on 3D fatigue crack propagation in surface-cracked specimens

In the present work the fatigue crack growth in AISI304 specimens is investigated experimentally. In 3D finite element analysis the virtual crack closure technique is applied to calculate distributions and variations of the stress intensity factor along the surface crack front. It is confirmed that the stress intensity factor along the surface crack front varies non-uniformly with crack growth. Crack growth rate is proportional to the stress intensity factor distribution in the 3D cracked specimen. The fatigue crack growth in surface cracked specimens can be described by the Forman model identified in conventional compact tension specimens. For crack growth in the free specimen surface the arc length seems more suitable to quantify crack progress. Geometry and loading configuration of the surface cracked specimen seem to not affect the fatigue crack growth substantially.     

Effects of mixed-mode overloading on the mixed-mode I+II fatigue crack growth

In this study, the finite element modeling of the compact tension shear specimens has been used to evaluate the effects of overloading on fatigue crack growth with mixed-mode loading I+II. Element creation and modeling is done by CASCA software. FRANC2D was used for stress analysis and the determination of crack parameters. Life estimation of samples was done by using the software ETBX. To create the mixed-mode I+II, different loading angles of 0, 15, 45 and 75 degrees (with respect to normal direction to the crack surface) were used with various overloading ratios. The effects of residual stresses due to overloading with saving and restoring capabilities were considered as a separate loading. To confirm the modeling results, models were built with ABAQUS and also compared with the results of numerical and experimental data in the literature. There are good agreements in determining the path of the crack growth and life estimation. The effects of the loading direction, overloading ratio and its load ratio, combination of overloadings and their locations on the fatigue crack growth and life are investigated.     

纤维增强树脂基复合材料多轴疲劳研究进展

纤维增强树脂基复合材料结构在工程应用中常常承受复杂载荷的作用, 从而使材料处于多轴循环应力条件下. 为了更加合理地进行复合材料结构设计, 必须对复合材料多轴疲劳行为进行深入的研究, 建立比较理想的复合材料疲劳寿命预测模型. 首先简单回顾了复合材料单轴疲劳损伤判据及其寿命预测模型, 然后结合作者的研究结果, 总结了近年来国内外纤维增强树脂基复合材料多轴疲劳理论的研究成果, 对各种失效准则、疲劳寿命预测模型进行了较为深入的分析, 指出了它们各自的特点及其存在的问题, 并对复合材料多轴疲劳理论的研究趋势作出了展望. 最后, 对目前常用的复合材料多轴疲劳实验方法进行了总结, 并指出了各种方法的优缺点及其实验中存在的困难.      

Symmetric-Galerkin boundary element analysis of the dynamic T-stress for the interaction of a crack with an auxetic inclusion

In this work, the symmetric-Galerkin boundary element method (SGBEM) for 2-D elastodynamics in the Laplace-space frequency domain (Laplace domain) is employed to study the dynamic stress intensity factors (DSIFs) and the dynamic T-stress (DTS) during the interaction between a crack and an auxetic inclusion under impact loading conditions. It is found that, while the auxeticity has virtually no effect on the DSIFs, its influence on the DTS is noticeable. This finding is particularly important as it implies the imperative need of fracture criteria based on both the DSIFs and DTS for predicting crack growth in composite materials with auxetic phases.     

A cyclic steady-state method for fatigue crack propagation: Evaluation of plasticity-induced crack closure in 3D

The numerical study of plasticity-induced crack closure using the node-release technique presents many difficulties widely studied in literature. For instance various rules, proposed for overcoming mesh sensitivity, are challenged by more recent studies. This paper intends to propose and evaluate a numerical method for the investigation of crack propagation under fatigue loading, and particularly for the assessment of plasticity-induced crack closure in three-dimension. The method is an extension of the “steady-state method” to cyclic loadings. The steady-state method allows a direct computation (on a fixed mesh, without releasing nodes) of stress and strain fields around the crack tip and in the wake for a steady crack growth. The method is extended to simulate crack propagation under fatigue loading. Therefore it constitutes a valuable numerical tool for gaining insight into the physics of crack propagation, as it provides accurate mechanical fields around the crack tip and their relation with crack growth rate, various loading modes and parameters. The proposed method is also compared with the classical node-release technique. A very good agreement between the two methods is found. However the steady-state method needs much less mesh refinement and computational time. Following an analysis of some features of the fatigue crack, a discussion on a crack closure criterion is opened, and a reliable criterion for the determination of local crack closure is proposed.     

拉-拉循环荷载作用下的界面脱粘研究

应用弹性力学和断裂力学基本理论，基于剪滞模型，研究了纤维增强复合材料中纤维与基体界面在拉-拉循环荷载作用下的疲劳脱粘特性。建立了描述疲劳裂纹扩展的等效Paris公式，得到了界面疲劳脱粘扩展速率、脱粘应力以及脱粘界面的摩擦系数与循环加载次数的关系式。通过数值模拟计算，进一步分析了界面疲劳脱粘的力学机理。本文分析，考虑了疲劳加载引起的脱粘界面的损伤及损伤分布的不均匀性。同时还考虑了材料泊松比的影响。     

含缺口试件疲劳全寿命预测一种建议的方法

传统的研究含缺口构件的疲劳的方法是将疲劳启裂和疲劳裂纹扩展两个过程完全独立起来,用不同的方法来模拟,相互间并没有定量的关系。本文是基于最新发展的多轴疲劳损伤理论,建立了一种适用于各种载荷条件下的疲劳启裂和裂纹扩展的普适方法。根据从弹塑性分析中得到的应力应变,确定疲劳损伤模型,建立能够预测疲劳启裂、裂纹扩展速率和扩展方向的新方法。整个模拟可以分为两步:弹-塑性应力分析得到材料的应力应变分布;再运用一个通用的疲劳准则预测疲劳裂纹启裂和裂纹扩展。通过对1070号钢含缺口试件的疲劳全寿命预测,得到了与实验非常吻合的模拟结果。     

单元类型和尺寸对裂尖疲劳塑性数值模拟的影响研究

本文采用Jiang-Sehitoglu循环塑性模型和多轴疲劳准则对紧凑拉伸式样裂尖的循环塑性变形、裂纹扩展速率和残余应力进行了有限元数值模拟,着重考察了单元的类型和最小单元尺寸对裂尖循环塑性和裂纹扩展速率的影响.紧凑拉伸试样的材料为1070钢,数值模拟采用了线性单元(四节点)和二次单元(八节点)两种单元,裂尖附近有限元单元的最小尺寸从0.007mm到0.24mm不等.文中将裂纹扩展速率的预测值与实验值进行了比较,通过对裂纹扩展速率的比较,确定在疲劳塑性分析时对单元类型和尺寸进行合理选取.     

Experimental Investigation and Finite Element Analysis of Fatigue Crack Growth in Pipes Containing a Circumferential Semi-elliptical Crack Subjected to Bending

In this paper, a circumferential external surface flaw in a metallic round pipe under cyclic bending loading is considered. Because of very rapid changes in the geometrical parameters around the crack front region, the mesh generation of this region must be done with great care. This may lead to an increase in the run time which makes it difficult to reach valid results and conclusions. Because of the advantages of the sub-modeling technique in problems which need very high mesh density, this method is used. Stress intensity factors in mode I condition are determined using three-dimensional finite element modeling with 20 node iso-parametric brick elements in the ANSYS 9.0 standard code and the singular form of these finite elements at the crack front. In order to estimate the analysis error, the structural parameter error in energy norm criterion was used. Because of the advantages of non-dimensional analysis, this method is employed, and the stress intensity factors are normalized. For the analysis of the fatigue crack growth, the Paris law is used. The propagation path of the surface flaw is obtained from the diagram of aspect ratio versus relative crack depth. The fatigue crack growth analysis (the relative crack depth against loading cycles diagram) of different initial crack aspect ratio under cyclic loading is also considered. Fatigue shape development of initially semi-elliptical external surface defects is illustrated. The effect of the Paris exponent (material constant) on fatigue crack propagation is shown as well. Moreover, the fatigue crack growth of several specimens is assessed experimentally using a manually-constructed experimental set up. Finally, the experimental results obtained by cyclic bending loading tests are compared with the numerical results. The experimental results show good conformity with the finite element results.     

Definition of a new predictor for multiaxial fatigue crack nucleation in rubber

From an engineering point of view, prediction of fatigue crack nucleation in automotive rubber parts is an essential prerequisite for the design of new components. We have derived a new predictor for fatigue crack nucleation in rubber. It is motivated by microscopic mechanisms induced by fatigue and developed in the framework of Configurational Mechanics. As the occurrence of macroscopic fatigue cracks is the consequence of the growth of pre-existing microscopic defects, the energy release rate of these flaws need to be quantified. It is shown that this microstructural evolution is governed by the smallest eigenvalue of the configurational (Eshelby) stress tensor. Indeed, this quantity appears to be a relevant multiaxial fatigue predictor under proportional loading conditions. Then, its generalization to non-proportional multiaxial fatigue problems is derived. Results show that the present predictor, which is related to the previously published predictors, is capable to unify multiaxial fatigue data.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束,在使用的振动环境中,会因弯曲应力而导致破裂,影响到飞行安全.本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究.首先在对8 mm、12 mm无缺陷导管和含U型缺口8 mm导管的疲劳试验和有限元分析的基础上,得到了导管的最大拉应变-裂纹萌生寿命数据.然后采用基于强度极限和弹性模量估算法的Manson-Coffin公式来预测导管裂纹萌生寿命.最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数,使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度.