荧光探针法研究核壳结构有机硅-丙烯酸酯乳液的聚合行为

以芘为荧光探针,探讨了有机硅-丙烯酸酯核壳乳液聚合过程中,芘的第一振动峰(373 nm处)与第三振动峰(384 nm处)荧光强度的比值I1/I3与乳化剂、有机硅单体(D4)和引发剂(KPS)用量之间的关系,并结合聚合过程中探针芘的I1/I3峰值与单体转化率及乳胶粒形态演变之间的关系,研究了核壳结构有机硅-丙烯酸酯乳液的聚合行为.研究结果表明,探针芘的I1/I3峰值随乳化剂用量,D4用量,KPS用量不同发生相应的变化,随单体转化率的增加而增大.当乳化剂用量、D4用量、KPS与总单体的质量比依次为2 g、8 g、0.7%时,得到的乳液具有优良的综合性能.聚合反应过程中,当种子乳胶粒转变为核壳乳胶粒时,芘的I1/I3峰值仍呈现出明显的转变,说明有机硅-丙烯酸酯核壳乳液具有互穿聚合物网络结构.因此,荧光探针可用于研究有机硅-丙烯酸酯核壳乳液聚合反应进程.     

氧化-还原低温引发苯乙烯/丙烯酸丁酯细乳液共聚合动力学与成核机理的研究

详细讨论了 [(NH4 ) 2 S2 O8/NaHSO3 ]氧化 还原引发体系引发苯乙烯 (St)丙烯酸丁酯 (BuA)体系的细乳液共聚合的动力学特征及其与成核机理的关系 .细乳液的聚合速率比相同条件下的常规乳液聚合速率低 ,引发期长 .随聚合温度、引发剂浓度、乳化剂浓度的增加 ,聚合速率增大 .共乳化剂正十六烷 (HDE)的浓度在一定范围内增大 ,反应的速率增大 ,然后再增加HDE ,反应速率下降 .建立动力学曲线数学模型 ,并深入讨论了细乳液的聚合动力学特征 ,与常规乳液所得结果相比较 ,探讨了细乳液的单体液滴成核机理 .     

恒电流库仑分析法测定乙烯基三乙氧基硅烷

建立了恒电流库仑分析法测定乙烯基三乙氧基硅烷(VTES)含量的方法. 探讨了电解液、反应时间、极化电位、溶剂等因素对测定的影响. 结果表明, 选用V(甲酸)∶V(KBr (2 mol/L))∶V(乙醇)＝6∶1∶3为电解液, 极化电位为200 mV, VTES与溴的四氯化碳溶液反应30 min, 甲醇为VTES的溶剂时测定结果最佳. 该方法用于样品VTES的测定, 加标回收率为98.4%～102.7%, 相对标准偏差为1.7%.     

高固含量低粘度丙烯酸酯乳液压敏胶的制备

采用常规种子乳液聚合法合成出了固含量为65%、粘度小于400mPa·s的乳液压敏胶,研究了共聚单体、乳化剂、引发剂、缓冲剂及种子乳液量对丙烯酸酯共聚物乳液粘度和聚合稳定性的影响。结果表明:含羧基和羟基的功能单体对乳液的粘度和聚合稳定性影响较大;乳液压敏胶粘度随乳化剂量在预乳化液中所占比例增大及种子乳液量的增大而增大,随引发剂过硫酸铵(APS)用量增大而降低,随缓冲剂碳酸氢钠在预乳化液中所占比例增大先增大后减小;乳液压敏胶的聚合凝胶率随乳化剂量在预乳化液中所占比例增大及种子乳液量降低而减小,当APS为单体量的0.3%,NaHCO3在预乳化液和反应中的比例为2/4时,乳液凝胶率最低。     

有机硅-丙烯酸酯聚合物乳液合成及粒径分析

通过种子乳液半连续法合成了有机硅改性丙烯酸酯聚合物乳液,并对其粒子形态及分布进行分析。结果表明:通过种子乳液半连续聚合工艺可制备出固含量42wt%,乳化剂含量4wt%(基于单体量)、窄分布纳米粒子的有机硅改性丙烯酸酯聚合物乳液。随反应进行,粒径分布变窄,平均粒径逐渐增大。随乳化剂中SDS与OP-10的摩尔比减少,粒径增大。     

硅丙乳液的合成工艺研究

采用半连续种子乳液聚合工艺,以乙烯基三乙氧基硅烷(VTS)为改性剂、十二烷基硫酸钠(SDS)和烷基酚聚氧乙烯醚(OP-1O)为复合乳化体系,在引发剂过硫酸铵(APS)的作用下合成稳定的硅丙乳液.利用红外光谱(FTIR)和扫描电镜(SEM)对涂膜进行了表征.结果表明:单体转化率随乳化剂用量、引发剂用量、有机硅用量、聚合温...     

有机硅氧烷改性St/BA/AA三元共聚乳液的制备

采用核壳乳液聚合法,制备了乙烯基三乙氧基硅烷（VTES）改性的St/BA/AA三元共聚乳液,其结构经FT IR确证。研究了VTES用量、乳化剂用量及配比和引发剂用量对单体转化率和粒径的影响。结果表明：在最优条件［48%St, 48%BA, 4%AA, 1%N-MA, 4%VTES, 8%乳化剂（OP-10/SDS=1/3）, 0.8%引发剂］下,单体转化率为95.8%,平均粒径242 nm。并研究了改性St/BA/AA乳胶膜(1)的耐溶剂性和铅笔硬度。结果表明：1具有良好的耐溶剂性,铅笔硬度为2H。     

正交实验法优化氟硅丙乳液的制备工艺

利用L25(56)正交实验设计方法,研究了引发剂,乳化剂,有机硅、氟的用量以及聚合温度,单体配比等因素对乳液单体转化率的影响.在本实验条件下,得出制备氟硅丙乳液的最佳工艺条件为:乳化剂用量为4%,引发剂用量为ω=0.6%,单体配比为n(BA):n(MMA)=44:54,有机硅用量ω=10%,有机氟用量ω=4%,聚合温度...     

聚硅氧烷/丙烯酸酯核/壳复合胶乳的粒径分布与成核机理

通过种子乳液法合成出具有高有机硅含量核 壳结构的聚硅氧烷 丙烯酸酯复合粒子 .研究了聚合方法、乳化剂浓度、引发剂浓度、单体滴加速度等工艺条件对复合乳液粒径尺寸、分布与形态的影响 ,并对复合乳液的成核机理进行了探讨 .研究表明 ,乳化剂浓度对乳液粒子的粒径分布和形态、结构有显著影响 ,引发剂浓度增加将使粒子粒径减小 ;相对一次投料法 ,种子乳液法生成的粒子分布窄 ,具有明显核壳结构 ,通过壳层单体滴加速度可以控制粒子的粒径尺寸和分布 ;而壳层丙烯酸酯聚合物主要是在聚硅氧烷种子表面的“过渡层”聚合、富集而成 .     

ACPMA/BPO引发甲基丙烯酸甲酯聚合及其动力学

以4,4′-偶氮二[4-氰基戊酰(对-二甲氨基)苯胺](ACPMA)/过氧化二苯甲酰(BPO)为氧化还原引发体系,研究了甲基丙烯酸甲酯(MMA)在N,N-二甲基甲酰胺(DMF)中的聚合及其动力学行为.考察了聚合反应温度、单体浓度、ACPMA浓度和BPO浓度对聚合反应速率和聚合物分子量的影响,测定了反应级数和聚合反应的活化能.结果表明,在一定范围内,聚合反应速率随单体浓度增大、ACPMA浓度增大、BPO浓度增大和反应温度的升高而增大;聚合物分子量随单体浓度的增大而增大,随ACPMA浓度的增大、BPO浓度增大和反应温度的升高而降低.该体系具有氧化还原引发体系的特征,其引发MMA的聚合速率方程为Rp=K[ACPMA]0.57     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。