Interpolation formulas for maxwell viscosity of certain metals as a function of shear-strain intensity and temperature

The purpose of this study is the construction of interpolation formulas for the dependence of Maxwell viscosity, a quantity which is the reciprocal of shear-strain relaxation time , on shear-strain intensity and temperature for several metals: iron, aluminum, copper, and lead. This function was interpolated in various temperature and deformation velocity ranges in accordance with available experimental data for iron (0 10⁷ sec^–1, 200 ° T 1500 °); aluminum (0 10⁷ sec^–1, 300 ° T 900 °); copper (0 10⁵ sec^–1, 300 ° T 1300 °); lead (0 10⁶ sec^–1, 90 ° T 400 °); temperatures in °K.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 4, pp. 114–118, July–August, 1974.     

Hypersonic flow past blunt-edged delta wings

A method is proposed for calculating hypersonic ideal-gas flow past blunt-edged delta wings with aspect ratios = 100–200. Systematic wing flow calculations are carried out on the intervals 6 M 20, 0 20, 60 80; the results are analyzed in terms of hypersonic similarity parameters.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 175–179, September–October, 1990.     

Study of initial segment of turbulent jets of various gases in a parallel air stream

Results are presented of a study of the gasdynamic parameters and the geometric characteristics of the mixing zone of axisymmetric jets of gases of differing density (Freon-12, air, and helium) propagating in a parallel air stream, within the limits of the initial segment (0x/R3–30). Experimental data are presented on the effect of different densities (0. 27 n8.2) and velocities (0m1.7) of the gas jet and the parallel stream on the mixing process.     

Experimental investigation of separation of turbulent boundary layer in vicinity of a step

The results of an experimental investigation of the separation of a turbulent boundary layer in the vicinity of a step on a flat plate at M = 2 and 3, and Re = U/v = (26–66)·10⁶ m^–1 are given. The step height was varied from 3 to 16 mm, which corresponded to the range of relative heights 1.1 h/ 7.6, where is the thickness of the boundary layer at the point at which the pressure starts to increase in front of the step. The obtained data for the pressure distribution in front of the step, and on its face and top surface, and the results of probe measurements in the separation and adjacent regions provide a more accurate scheme of the flow. The obtained data are compared with the results of other investigations.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 73–80, September–October, 1977.We express our thanks to A. M. Kharitonov for valuable comments made during the discussion of this work, and also to M. A. Gol'dfel'd for kindly providing the experimental data for axisytnmetric steps.     

Approximate relationships for the determination of the pressure on the surface of a sphere or cylinder with an arbitrary mach number in the free stream

Numerical calculations have been made [1–4] of the pressure distribution over the surface of a sphere or cylinder during transverse flow in the range 0 /2, where is the angle reckoned from the stagnation point along the meridional plane, and on the basis of these results simple analytical equations have been proposed in order to determine the pressure for arbitrary Mach numbers M in the free stream. The gas is assumed to be ideal and perfect.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 185–188, March–April, 1985.     

Investigation of stationary flow of viscous gas in a thin three-dimensional shock layer

A three-dimensional shock layer near the blunt surface of a fairly smooth body is analyzed asymptotically. Equations of the first approximation are obtained and justified in various cases of the limit 1, 0, ( – 1)^–1M ^-2 0. These equations are simplified for the flow near the stagnation point of a body with double curvature and near the blunt leading edge of a sweptback wing. The results of some calculations are given and compared with the results of [17, 18] in the case of axisymmetric flow.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 115–126, September–October, 1980.     

Numerical solution of the Navier-Stokes equations for flow of gas around a rectangle

A difference scheme of the Lax-Wendroff type was used to solve the Navier-Stokes equations for the problem of flow of a perfect gas around a rectangle (cylinder of rectangular cross section) with and without a front plate for subsonic, transonic, and small supersonic flow velocities (Mach numbers 0.3M2 and Reynolds numbers 1R250). The occurrence and development of front, lateral, and rear separation of the flow are discussed, and the aerodynamic characteristics of the considered bodies are determined.Moscow. Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 4, pp. 10–17, July–August, 1972.     

Heat transfer to an isothermal flat plate in turbulent flow of a liquid over a wide range of prandtl and reynolds numbers

The study of heat transfer in turbulent flow over a flat plate is very important, not only because this situation frequently arises in practice, but also in that data for an isothermal flat plate are used to calculate heat transfer in more complex cases. In particular, such data are necessary when one uses the limiting relative laws which allow calculation of the effect of compressibility, pressure gradient, blowing, and other perturbing factors [1]. Most papers dealing with heat transfer for an isothermal flat plate refer to comparatively low Re values, when the velocity distribution in the boundary layer over almost its entire thickness can be described by the universal law of the wall. However, as Re increases there is an increasing layer adjacent to the outer boundary in which the velocity distribution cannot be described by the law of the wall, and therefore the results obtained for low Re are inapplicable. In the present paper coefficients of heat transfer from a turbulent flow to an isothermal flat plate have been obtained by numerical integration of the thermal boundary-layer equations over a wide range of the parameters 3 · 10⁵ Re 2.5·10¹², 10² Pr 10³.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 4, pp. 94–100, July–August, 1976.     

About the Regularized Navier–Stokes Equations

The first goal of this paper is to study the large time behavior of solutions to the Cauchy problem for the 3-dimensional incompressible Navier–Stokes system. The Marcinkiewicz space L^3, is used to prove some asymptotic stability results for solutions with infinite energy. Next, this approach is applied to the analysis of two classical regularized Navier–Stokes systems. The first one was introduced by J. Leray and consists in mollifying the nonlinearity. The second one was proposed by J.-L. Lions, who added the artificial hyper-viscosity (–)^{/ 2}, > 2 to the model. It is shown in the present paper that, in the whole space, solutions to those modified models converge as t toward solutions of the original Navier–Stokes system.     

Asymptotic solution to the problem of hypersonic flow over bodies in the neighborhood of the separation point of a thin shock layer

A study is made of the problem of hypersonic flow of an inviscid perfect gas over a convex body with continuously varying curvature. The solution is sought in the framework of the asymptotic theory of a strongly compressed gas [1–4] in the limit M when the specific heat ratio tends to 1. Under these assumptions, the disturbed flow is situated in a thin shock layer between the body and the shock wave. At the point where the pressure found by the Newton-Buseman formula vanishes there is separation of the flow and formation of a free layer next to the shock wave [1–4]. The singularity of the asymptotic expansions with respect to the parameter ₁ = ( –1)/( + 1) associated with separation of the strongly compressed layer has been investigated previously by various methods [3–9]. Local solutions to the problem valid in the neighborhood of the singularity have been obtained for some simple bodies [3–7]. Other solutions [7, 9] eliminate the singularity but do not give the transition solution entirely. In the present paper, an asymptotic solution describing the transition from the attached to the free layer is constructed for a fairly large class of flows.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 99–105, January–February, 1982.     

Torsion of two bonded layers by a rigid disk

The problem considered in this paper describes the torsion of a homogeneous isotropic elastic layer (0zd ₁) of finite thickness d ₁, perfectly bonded to another elastic layer (-d ₂z0) of finite thickness d ₂. The problem is reduced to the solution of a Fredholm integral equation of the second kind. The solutions are given for some particular cases.

---

Sommario In questo lavoro si considera il problema della torsione di uno strato elastico omogeneo ed isotropo (0zd ₁) di spessore finito d ₁, perfettamente incollato ad un altro strato elastico (-d ₂z0) di spessore finito d ₂. II problema é ricondotto alla soluzione di una equazione integrale di Freedholm del secondo ordine. Le soluzioni sono ottenute per alcuni casi particolari.

     

On shock layer method for the hypersonic flow problems

Chernyi’s series method[1] is not proper for the case that(γ-l)/(γ+l)<<2/(γ+1)×M²sin²β (γ=c_p/c_v-adiabatic index number, M-Much number, β-shock incidence). In this paper, we only suppose that in the neighbour of the shock, there exists a shock layer in which the density of the gas is very big, but we do not remove the case that (γ-1)/(γ+1)<<2/(γ+1)M²sin²β.     

The rheology of polymeric liquid crystals

The molecular theory of Doi has been used as a framework to characterize the rheological behavior of polymeric liquid crystals at the low deformation rates for which it was derived, and an appropriate extension for high deformation rates is presented. The essential physics behind the Doi formulation has, however, been retained in its entirety. The resulting four-parameter equation enables prediction of the shearing behavior at low and high deformation rates, of the stress in extensional flows, of the isotropic-anisotropic phase transition and of the molecular orientation. Extensional data over nearly three decades of elongation rate (10^–2–10¹) and shearing data over six decades of shear rate (10^–2–10⁴) have been correlated using this analysis. Experimental data are presented for both homogeneous and inhomogeneous shearing stress fields. For the latter, a 20-fold range of capillary tube diameters has been employed and no effects of system geometry or the inhomogeneity of the flow-field are observed. Such an independence of the rheological properties from these effects does not occur for low molecular weight liquid crystals and this is, perhaps, the first time this has been reported for polymeric lyotropic liquid crystals; the physical basis for this major difference is discussed briefly. A Semi-empirical constant in eq. (18), N/m² - c rod concentration, rods/m³ - c ^* critical rod concentration at which the isotropic phase becomes unstable, rods/m³ - C interaction potential in the Doi theory defined in eq. (3) - d rod diameter, m - D semi-empirical constant in eq. (19), s^–1 - D _r lumped rotational diffusivity defined in eq. (4), s^–1 - rotational diffusivity of rods in a concentrated (liquid crystalline) system, s^–1 - D _ro rotational diffusivity of a dilute solution of rods, s^–1 - f distribution function defining rod orientation - F tensorial term in the Doi theory defined in eq. (7) (or eq. (19)), s^–1 - G tensorial term in the Doi theory defined in eq. (8) - K _B Boltzmann constant, 1.38 × 10^–23 J/K-molecule - L rod length, m - S scalar order parameter - S tensor order parameter defined in eq. (5) - t time, s - T absolute temperature, K - u unit vector describing the orientation of an individual rod - rate of change ofu due to macroscopic flow, s^–1 - v fluid velocity vector, m/s - v velocity gradient tensor defined in eq. (9), s^–1 - V mean field (aligning) potential defined in eq. (2) - x coordinate direction, m - Kronecker delta (= 0 if = 1 if = ) - _r ratio of viscosity of suspension to that of the solvent at the same shear stress - _s solvent viscosity, Pa · s - ^* viscosity at the critical concentrationc ^*, Pa · s - v ₁, v₂ numerical factors in eqs. (3) and (4), respectively - deviatoric stress tensor, N/m² - volume fraction of rods - ⁰ constant in eq. (16) - ^* volume fraction of rods at the critical concentrationc ^* - average over the distribution functionf(u, t) (= d ²u f(u, t)) - gradient operator - d ²u integral over the surface of the sphere (|u| = 1)     

Flow of a viscous gas in a shock layer with equilibrium chemical reactions

Steady flow of supersonic air over a sphere is examined, allowing for viscosity, heat conduction, and actual physical and chemical processes. Flow in the shock layer at flight speeds in the range 3 km/sec V10 km/sec (10⁴R10⁶) is investigated, under the assumption of local thermodynamic equilibrium. The flow is described by simplified Navier-Stokes equations, which are solved by a finite difference method. The case of a cooled surface is examined. The distribution of gasdynamic parameters is obtained in different flow regimes. The distribution of heat flux and friction coefficient is investigated as a function of the oncoming-stream parameters and the sphere radius. The shape and position of the shock wave are determined, and the stream lines and sonic lines are constructed.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 4, pp. 150–153, July–August, 1970.The authors thank Yu. P. Lun'kin and F. D. Popov for their help in formulating the problem and their constant interest.     

A MEMS skin-friction sensor for time resolved measurements in separated flows

A MEMS surface fence sensor for skin-friction measurements in separated flows has been developed and tested successfully in low-speed flows. The new sensor is able to distinguish between forward and reverse flow and features a temporal resolution of up to 1 kHz. Calibrations of the sensor have been obtained in the range of –0.7 N m^-2_w0.7 N m^-2 with a resolution of 0.02 N m^-2. Comparative measurements with the wall-pulsed wire technique in a reverse-flow region show excellent agreement with respect to the mean skin-friction coefficient c_f but also reveal some discrepancies for the fluctuating part c_f.     

Change in the parameters of a supersonic flow in the presence of transverse blowing

A study has been made of the flow formed in a supersonic nozzle when gas is blown in a transverse jet into an expanding supersonic flow. Measurements were made of the total and static pressures of the flow at several sections of the nozzle. It was established that, depending on the relative flow rate = m_j/(m_j+ m₀) of the blown gas (m_jand m₀ are the flow rates of the blown gas and the main flow, respectively), there exist two flow regimes with different dependences of the Mach number of the flow. At small , the experimental flow parameters correspond satisfactorily to the parameters calculated in a one-dimensional model with a narrow mixing layer near the blowing section. Agreement was observed at flow rates less than a certain ^*, this critical value being determined in the model as the flow rate at which the flow after mixing becomes sonic. In the experiments at large flow rates of the blown gas, ^* < < 1, the value of M for the flow hardly depends on and corresponds to the calculated value of M for a supersonic flow having the velocity of sound near the blowing section. A scheme is proposed for calculating the flow in a nozzle with transverse blowing in the supersonic part; it describes satisfactorily the experimental results in the complete range of blown-gas-main-flow flow rate ratios (0 1) over the complete length of the nozzle.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 188–192, May–June, 1984.     

Plastic deformation of metals subjected to intensive sources

The elastoplastic strain of metals being formed when they melt under the effect of a point heat source with a pulse duration greater than 10^–6 sec is considered in this paper. The time development of the plastic strain and pressure domains in the melt is investigated. It is shown that two plastic strain domains occur during the interaction under consideration: a relatively broad domain of mechanical influence and a narrow domain of thermal influence. The stress-strain distributions as well as the hydrostatic pressure in the fluid are determined by a quasistationary temperature distribution starting with times corresponding to half (of the quasistationary) the value of the melt radius X 0.5. It is shown that the dimensions of the weak and strong plastic strain domains formed by heat and acoustic waves grow continuously to the quasistationary values, while the hydrostatic pressure in the fluid reaches the maximum value for X 0.3...0.4. The ratio between the radii of the plastic strain zones and of the liquid bath for a quasistationary temperature distribution in the first domain lies within the range 10–50, and does not exceed 1.7 for Cu, Ni, and Fe in the second. The anomalous nature of the development of the strong plastic strain domain in Al, because of migration of the metal grain boundaries to result in collapse of the domain for the values X 0.5 accompanied by a jumplike diminution in the hydrostatic pressure in the fluid, is noted.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 3, pp. 129–140, May–June, 1976.     

Interaction between a distributed source and the free surface of a viscous fluid

A self-similar solution of the Navier-Stokes equations describing steady-state axisymmetric viscous incompressible fluid flow in a half-space is investigated. The motion is induced by sources or sinks distributed over a vertical axis with a constant density. The horizontal plane bounding the fluid is a free surface. It is found that in the presence of sources a solution of the above type exists and is unique for any value of the Reynolds numberR > 0, but in the case of sinks only on the interval –2 R < 0. The results of calculating the self-similar solutions are presented. The asymptotics of the solutions are found asR 0 andR .Novosibirsk. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 2, pp. 53–65, March–April, 1996.     

Flow structure in motion of a spherical drop in a fluid medium at intermediate Reynolds numbers

The problem of flow of a viscous fluid around a spherical drop has been examined for the limiting case of small and large Reynolds numbers in several investigations (see [1–3], for instance; there is a detailed review of various approximate solutions in [4]). For the intermediate range of Reynolds numbers (approximately 1Re100), where numerical integration of the complete Navier-Stokes equations is necessary, there are solutions of special cases of the problem —flow of air around a solid sphere [5–7], a gas bubble [8, 9], and water drops [10]. The present paper deals with flow around a spherical drop at intermediate Reynolds numbers up to Re=200 for arbitrary values of the ratio of dynamic viscosities =₁/₂ inside and outside the drop. It is shown that a return flow can arise behind the drop in flow without separation. In such conditions the circulatory flow inside the drop breaks up. An approximate formula for the drag coefficient of the drop is given.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 8–15, January–February, 1976.We thank L. A. Galin, G. I. Petrov, L. A. Chudov, and participants in the seminars led by them for useful discussions.     

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²