Ti_(100-δ)Cu_δ(δ=0.02,0.28,1.39,5.65)阴极的制备及电催化还原NO_3~-机理

以Ti板为基体,采用异位电沉积法通过调控电镀时间制备了质量分数(δ)分别为0.02,0.28,1.39和5.65的Ti_(100-δ)Cuδ阴极;利用扫描电子显微镜(SEM)、X射线衍射(XRD)、电化学测试及NO_3~-处理实验等手段对其微观形貌、物相组成、电催化活性、抗腐蚀性能和产物选择性等进行了表征.结果表明,δ≥0.28时Ti_(100-δ)Cuδ电极表面的Cu镀层呈现(111)晶面择优取向,可有效提高电极稳定性;Cu活性层的形成为NO_3~-的吸附提供了活性点位,增强了电极的电催化性能,但Cu的加入会降低电极抗腐蚀性能;在一定的载铜量范围内,单质Cu对NO_3~-降解产物NO-2的吸附有一定的抑制作用,但会增强NO-2的还原反应活性,提高N2选择系数.应用Ti_(100-δ)Cuδ(δ=5.65)阴极在电流密度为20 m A/cm2、电解时间6 h条件下对NO_3~-进行处理,结果表明,NO_3~-去除率和N2选择系数分别高达75.47%和32.65%,与Ti电极的NO_3~-去除率(39.89%)和N2选择系数(2.19%)相比有显著提高.     

Oxygen permeability and CO_2-tolerance of Ce_(0.8)Gd_(0.2)O_(2-δ)-Ln BaCo_2O_(5+δ) dual-phase membranes

A series of oxygen permeable dual-phase composite oxides 60 wt% Ce0.8Gd0.2O2-δ-40 wt% Ln Ba Co2O5+δ(CGO-LBCO, Ln = La, Pr, Nd,Sm, Gd and Y) were synthesized through a sol-gel route and effects of the Ln3+cations on their phase structure, oxygen permeability and chemical stability against CO2 were investigated systemically by XRD, SEM, TG-DSC and oxygen permeation experiments. XRD patterns reveal that the larger Ln3+cations(La3+, Pr3+and Nd3+) successfully stabilized the double-layered perovskite structure of sintered LBCO,while the smaller ones(Sm3+, Gd3+, and Y3+) resulted in the partial decomposition of LBCO with some impurities formed. CGO-PBCO yields the highest oxygen permeation flux, reaching 2.8×10-7mol s-1 cm-2at 925?C with 1 mm thickness under air/He gradient. The TG-DSC profiles in 20 mol% CO2/N2 and oxygen permeability experiments with CO2 as sweep gas show that CGO-YBCO demonstrates the best chemical stability against CO2, possibly due to its minimum basicity. The stable oxygen permeation flux of CGO-YBCO under CO2 atmosphere reveals its potential application in the oxy-fuel combustion route for CO2 capture.     

Synthesis and Characterization of Li(11)Nd(18)Fe(4)O(39-δ)

Li(11)Nd(18)Fe(4)O(39-δ) has been synthesized by the solid-state reaction of pellets, covered with powder of the same composition to avoid lithium loss, with a final reaction temperature of 950 °C. This phase has been reported previously to have various stoichiometries: Li(5)Nd(4)FeO(10), Li(8)Nd(18)Fe(5)O(39), and Li(1.746)Nd(4.494)FeO(9.493). The crystal structure of Li(11)Nd(18)Fe(4)O(39-δ) is closely related to that reported previously for two of the other three compositions but contains extra Li and differences in Li/Fe site occupancies. Fe is present in a mixture of 3+ and 4+ oxidation states, as confirmed by M?ssbauer spectroscopy. The oxygen content of 39 - δ is variable, depending on the processing conditions. Samples slow-cooled in air from 800 °C are semiconducting, attributed to the presence of Fe(4+) ions, whereas samples quenched from 950 °C in N(2) are insulating.     

Mixed-conducting perovskite-type Sr_xBi_(1-X)FeO_(3-δ)oxygen-permeating membranes

SrxBi1-xFeO3- (SBF) series mixed conductors were synthesized using Standard ceramic method. The properties of such materials were characterized by XRD, O2-TPD techniques. Ab-normal crystal phenomena were found and explained and correlated with the oxygen permeation results. By analysis of the critical radius (rc), the degree of openness of the lattice (Fv) and the average metal-oxygen bonding energy of the perovskite lattice (ABE), it was proposed that the oxygen permeation flux is determined mainly by the oxygen diffusion rate in bulk when 1-x≤0.5, and by the concentration of oxygen vacancy when 1-x≥ 0.5. The stability of Sr0.5Bi0.5FeO3- was also investigated, and the high stability of it was attributed to the stable BO6 octahedra.     

La_(2-x)Pr_xNiO_(4+δ)体系低频内耗研究

利用内耗技术对La2-xPrxNi O4+δ(0≤x≤2.0)体系额外氧的状态进行了深入研究。La2-xPrxNi O4+δ(0≤x≤2.0)系列样品的XRD数据拟合计算得出:当x小于等于0.75时,体系为四方结构,而当x大于0.75时,体系转变为正交结构。通过对体系低频内耗和模量的测量研究发现,当0≤x≤0.75时,样品只存在一个弛豫内耗峰(P1峰),其峰值随x值增大而增大,与额外氧的浓度成正相关;当1.0≤x≤2.0时,样品中存在两个弛豫内耗峰,分析研究表明:高温侧内耗峰P1对应着前面发现的内耗单峰,它是由ab面额外氧对的取向弛豫运动引起的,在这里该内耗峰峰值随x值增大而减小,显然是受到额外氧的三维有序结构形成的影响。低温侧内耗峰峰P2可能与额外氧对的新的组态运动方式有关。     

Novel Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ) membranes for POM

A novel cobalt-free perovskite based on Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ)(BSFZ)were prepared by EDTA-citric acid method.The lattice constants of the BSFZ perovskite were characterized by in situ high-temperature X-ray diffraction(HTXRD).The thermal expansion coefficient of BSFZ is 10.5×10~(-6)K~(-1),which is lower than that of cobalt-based perovskite materials.The BSFZ membrane was also used to construct reactors for the partial oxidation of methane(POM)to syngas.Results show that the BSFZ membrane...     

Raman analysis of mode softening in nanoparticle CeO(2-δ) and Au-CeO(2-δ) during CO oxidation

Oxygen vacancy levels are monitored during the oxidation of CO by CeO(2-δ) nanorods and Au-CeO(2-δ) nanorods, nanocubes, and nanopolyhedra by using Raman scattering. The first-order CeO(2) F(2g) peak near 460 cm(-1) decreases when this reaction is fast (fast reduction and relatively slow reoxidation of the surface), because of the lattice expansion that occurs when Ce(3+) replaces Ce(4+) during oxygen vacancy creation. This shift correlates with reactivity for CO oxidation. Increases in the oxygen deficit δ as large as ~0.04 are measured relative to conditions when the ceria is not reduced.     

Novel SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) membrane for hydrogen separation

<正>Dense ceramic membranes with protonic and electronic conductivity have attracted considerable interest in recent years.In this paper,the powders of SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) were synthesized via the liquid citrate method,and the membranes of SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) were prepared by pressing followed by sintering.X-ray diffraction(XRD) was used to characterize the phase structure of both the powder and sintered membrane.The microstructure of the sintered membranes was studied by scanning electron microscopy(SEM).Hydrogen permeation through the SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) membranes was carried out using gas permeation setup at 900℃.Hydrogen permeation flux of SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) membrane reaches up to 0.042 mL/ min cm~2 at H_2 partial pressure of 0.4 atm.The hydrogen permeation fluxes obtained in this paper are similar to that of SrCe_(0.95)Tm_(0.05)O_(3-δ),and Zr doping can increase mechanical strength of SrCe_(0.75)Zr_(0.20)Tm_(0.05)O_(3-δ) membranes and the resistance to reducing circumstance.     

纳米荧光粉Eu_(0.12)Y_(1.88-x)Mg_xO_(3-δ)的光致发光特性

使用超声波作用下的均匀沉淀法,制备了掺杂Mg2+的纳米荧光粉Y2O3:Eu3+.考察了不同Mg2+掺杂含量下Eu0.12Y1.88-xMgxO3-δ(x=0～0.18,δ代表氧空位)的晶格常数变化,研究了掺杂含量对样品发射光谱及激发光谱的影响.结果表明,Eu0.12Y1.88-xMgxO3-δ的晶格常数在1.0604～1.062 3 nm之间,晶粒尺寸在25.9～40.7 nm之间.掺杂Mg2+后,当x=0.14时,样品Eu0.12Y1.74Mg0.14O3-δ的激发光谱中电荷迁移带(CTS)最大峰强度最高且色纯度最好.     

γ(δ)-内酯氧化合成4(5)-氧代羧酸

以γ(δ)-内酯(1或2)为原料,次氯酸钠(NaC lO)为氧化剂,分别合成了具有不同碳链长度的4(5)-氧代羧酸(3或4),其结构经NMR和MS表征。考察了NaC lO用量,pH值和反应温度对产率的影响。较适宜的反应条件为:1(或2)15 mmol,NaC lO 35 mL,pH 8~9,冰水浴下反应,3(或4)的产率35%~92%。     

Preparation and hydrogen permeation properties of BaCe_(0.95)Nd_(0.05)O_(3-δ) membranes

Dense mixed proton and electron conducting membrane made of BaCe_(0.95)Nd_(0.05)O_(3-δ)(BCNd5)was prepared by pressing followed by sintering.X-ray diffraction(XRD)was used to characterize the phase structure of both the powder and the sintered membranes.The microstructure of the sintered membranes was studied by scanning electron microscopy(SEM).Hydrogen permeation through the BCNd5 membrane was studied using a high temperature permeator.The hydrogen permeation fluxes under wet conditions are higher than those under dry conditions,which is due to H~ hopping via surface OH groups.At 925℃,a hydrogen permeation flux of 0.02 mL/min cm~2 was obtained under wet condition,which recommends BCNd5 as a potential material for hydrogen-selective membranes.     

Nd_(1 x)Ba_(2-x)Cu_3O_(7-δ)超导体的热处理

通过对Nd1 xBa2 -xCu3O7-δ的两种样品 (烧结样品和区域熔炼样品 )的XRD谱图分析 ,研究了高温氩气氛下热处理对样品中Nd对Ba的取代值x的影响 ,同时比较了不同样品的Tc 和Jc 值。研究表明 ,氩气下 95 0℃热处理可以减少Nd对Ba的取代 ,Tc 和Jc 都有不同程度的提高。对不同固溶度x值的Nd1 xBa2 -xCu3O7-δ进行吸氧热处理 ,样品在热处理前后分别作XRD分析。从XRD谱图可以看出 :当x <0 4时 ,样品经吸氧后可以从四方相转变为正交相 ,而当x >0 4时 ,样品虽经长时间吸氧也不能使其从四方相转变为正交相     

SrFe_(0.6)Cu_(0.3)Ti_(0.1)O_(3-δ)混合导体透氧材料的稳定性

利用柠檬酸络合法制备了SrFe(Cu,Ti)O_(3-δ)混合导体透氧材料. 采用XRD、O_2-TPD、H_2-TPR、SEM等测试技术考察了材料的稳定性. 结果表明,SrFe_(0.7)Cu_(0.3)O_(3-δ)在低氧压下会发生相分解,产生SrCuO__2杂相,而掺杂Ti后的SrFe_(0.6)Cu_(0.3)Ti_(0.1)O_(3-δ)在低氧压下保持单一的钙钛矿结构. H_2-TPR和O_2-TPD的测试表明,Ti~(4+)的掺杂提高了材料的氧脱附起始温度和其它金属离子的还原温度. SrFe_(0.6)Cu_(0.3)Ti_(0.1)O_(3-δ)膜在透氧过程中,会有Cu~(2+)和Sr~(2+)从钙钛矿结构中析出,在原晶粒边界形成新的小晶粒,但这种轻微的组分偏析没有影响到材料的透氧量,此透氧膜在66 h的操作过程中显示了良好的稳定性.     

类溶胶-凝胶法制备LiMn_2O_(4-δ)Cl_δ正极材料

本文以水合氢氧化锂 (LiOH .H2 O)、水合硝酸锰 (Mn(No3) 2 .6H2 O) ,水合氯化锂 (LiCl.H2 O)为原料 ,用类溶胶 凝胶法制备了LiMn2 O4 δClδ,并且以此作正极进行了电化学测试 .结果表明 ,掺氯的尖晶石LiMn2 O4 正极材料具有优异的稳定性 ,且循环稳定后 ,容量几乎没有衰减 .     

Hydrogen Permeation Properties of Perovskite-type BaCe_(0.9)Mn_(0.1)O_(3-δ)Dense Ceramic Membrane

In recent years, mixed-conducting oxides, in which both protonic and electronic charge carriers exist, have received increasing attentions1. Ceramic membranes made of such materials are semipermeable to hydrogen at elevated temperatures. In the early 1980s, Iwahara et al. first reported protonic conduction in SrCeO3-based materials2. Later, BaCeO3 system was extensively studied because of its higher conductivities. However, the electronic conductivity of rare earth doped-BaCeO3 ceramic…     

MgO掺杂Ce_(0.9)Sm_(0.1)O_(2-δ)固体电解质的结构和电性能

采用溶胶-凝胶法合成SiO2含量为5.0×10-4(w)的Ce0.9Sm0.1O2-δ(SDC)粉体(SDCSi),并将0-3.0%(x)MgO分别加入到SDCSi陶瓷粉体中,用X射线衍射(XRD)和场发射扫描电子显微镜(FE-SEM)对材料进行表征,用交流阻抗谱(AC)测试材料的电性能.结果表明:MgO掺杂能使SDCSi的烧结温度降低100-200℃,提高陶瓷材料的致密度;清除或降低陶瓷材料晶界处SiO2杂质的有害影响,显著提高晶粒/晶界电导率和总电率;MgO掺杂到SDCSi具有烧结助剂和晶界杂质清除剂的双重作用.     

固体电解质Ce_(0.9)Er_(0.1-x)Pr_xO_(1.95+δ)的微观结构及电性能

采用柠檬酸溶胶-凝胶法制备了固体电解质Ce0.9Er0.1-xPrxO1.95+δ(x=0.02~0.08),利用X射线粉末衍射(XRD)、原子力显微镜(AFM)、拉曼光谱(Raman)、X射线光电子能谱(XPS)和交流阻抗谱研究了样品的微观结构和电性能.XRD结果表明,800℃煅烧的所有样品均形成了单相立方萤石结构;Raman光谱结果表明,Ce0.9Er0.05Pr0.05O1.95+δ具有氧缺位的立方萤石结构;XPS分析表明,Ce0.9Er0.05Pr0.05O1.95+δ存在氧缺位,Pr3+离子和Pr4+离子共存;AFM观测结果表明,1300℃下烧结的样品比1400℃下烧结的样品致密;交流阻抗谱结果表明,Pr掺杂量x=0.05时,Ce0.9Er0.05Pr0.05O1.95+δ的电导率最高(σ600℃=1.34×10-2S/cm,Ea=0.90 e V),比未掺杂Pr的Ce0.9Er0.1O1.95(σ600℃=8.81×10-3S/cm,Ea=0.92 e V)提高了52%,说明在Ce0.9Er0.1O1.95中适量掺杂Pr可提高材料的电导率,降低活化能.     

Sonochemical synthesis of Ce(1-x)Fe(x)O(2-δ) (0 ≤ x ≤ 0.45) and Ce(0.65)Fe(0.33)Pd(0.02)O(2-δ) nanocrystallites: oxygen storage material, CO oxidation and water gas shift catalyst

Nanocrystalline Ce(1-x)Fe(x)O(2-δ) (0 ≤ x ≤ 0.45) and Ce(0.65)Fe(0.33)Pd(0.02)O(2-δ) of ~4 nm sizes were synthesized by a sonochemical method using diethyletriamine (DETA) as a complexing agent. Compounds were characterized by powder X-ray diffraction (XRD), X-ray photo-electron spectroscopy (XPS) and transmission electron microscopy (TEM). Ce(1-x)Fe(x)O(2-δ) (0 ≤ x ≤ 0.45) and Ce(0.65)Fe(0.33)Pd(0.02)O(2-δ) crystallize in fluorite structure where Fe is in +3, Ce is in +4 and Pd is in +2 oxidation state. Due to substitution of smaller Fe(3+) ion in CeO(2), lattice oxygen is activated and 33% Fe substituted CeO(2)i.e. Ce(0.67)Fe(0.33)O(1.835) reversibly releases 0.31[O] up to 600 °C which is higher or comparable to the oxygen storage capacity of CeO(2)-ZrO(2) based solid solutions (Catal. Today 2002, 74, 225-234). Due to interaction of redox potentials of Pd(2+/0)(0.89 V) and Fe(3+/2+) (0.77 V) with Ce(4+/3+) (1.61 V), Pd ion accelerates the electron transfer from Fe(2+) to Ce(4+) in Ce(0.65)Fe(0.33)Pd(0.02)O(1.815), making it a high oxygen storage material as well as a highly active catalyst for CO oxidation and water gas shift reaction. The activation energy for CO oxidation with Ce(0.65)Fe(0.33)Pd(0.02)O(1.815) is found to be as low as 38 kJ mol(-1). Ce(0.67)Fe(0.33)O(1.835) and Ce(0.65)Fe(0.33)Pd(0.02)O(1.815) have also shown high activity for the water gas shift reaction. CO conversion to CO(2) is 100% H(2) specific with these catalysts and conversion rate was found to be as high 27.2 μmoles g(-1) s(-1) and the activation energy was found to be 46.4 kJ mol(-1) for Ce(0.65)Fe(0.33)Pd(0.02)O(1.815).     

质子导体(Ce_(0.8)La_(0.2))_(1-x)Ca_xO_(2-δ)在合成氨中的应用

利用溶胶-凝胶法合成了萤石型稀土复合氧化物(Ce_(0.8)La_(0.2))_(1-x)Ca_xO_(2-δ),利用XRD、TEM和SEM对样品进行表征.电化学方法研究表明,合成样品在400～800℃温度范围内具有质子导电特性.将(Ce_(0.8)La_(0.2))_(1-x)Ca_xO_(2-δ)高温烧结体用于固态质子传导电池,在常压下以氮气和氢气为原料合成氨气,并确定了合成氨的适宜条件.650℃时Ce0.8La0.2O2-δ和(Ce_(0.8)La_(0.2))_(1-x)Ca_xO_(2-δ)对应的氨产率分别达7.2×10-9和7.5×10-9mol·s-·1cm-2.     

Ce_(0.8)Nd_(0.2)O_(1.9)-La_(0.95)Sr_(0.05)Ga_(0.9)Mg_(0.1)O_(3-δ)固体复合电解质的结构和电性能

采用溶胶-凝胶法分别制备La0.95Sr0.05Ga0.9Mg0.1O3-δ(LSGM)和Ce0.8Nd0.2O1.9(NDC)电解质,并在NDC溶胶中加入0-15%(w,质量分数)的LSGM预烧粉体制得NDC-LSGM复合电解质,研究不同质量比复合电解质的结构和电性能.采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和X能量色散谱仪(EDS)对样品进行结构表征,交流(AC)阻抗谱测试样品导电性能.结果表明:NDC-LSGM复合体系主要由立方萤石结构相、钙钛矿结构相和杂质相组成;LSGM的添加可促进晶粒的生长,产生大量相界面,清除或降低SiO2有害影响,明显提高晶界导电性;LSGM质量分数为10%的样品NL10具有最高晶界电导率和总电导率,400°C时NL10的晶界电导率σgb和总电导率σt分别为12.15×10-4和3.49×10-4S cm-1,与NDC的σgb(1.41×10-4S cm-1)和σt(1.20×10-4S cm-1)相比分别提高了7.62和1.91倍,总电导率的提高主要归因于晶界电导率的影响.