Self-alignment of self-assembled InAs quantum dots

The lateral self-alignment properties of self-assembled InAs quantum dots (QDs) on a conventional GaAs (1 0 0) substrate by molecular beam epitaxy were investigated. The shape and optical properties of QDs were investigated by atomic force microscopy, transmission electron microscope, and photoluminescence (PL). Attempts were made to grow InAs-QDs using the In-interruption growth technique, in which the In flux was periodically interrupted. QDs grown without using the In-interruption growth technique were grown randomly on all regions. On the other hand, in the case of QDs grown using the In-interruption growth technique, QDs were self-aligned at the boundary between bright and dark regions, the PL intensity was increased and the PL peak position of QDs were red-shifted to 1300 nm. This represent a new technique for growing self-aligned QDs because no extra processing such as electron-beam lithography, V-grooves and surface modification by scanning tunneling microscopy is needed, and aligned QDs can be grown in situ on conventional GaAs substrates.     

The effect of inserting strain-compensated GaNAs layers on the luminescence properties of GaInNAs/GaAs quantum well

Photoluminescence (PL) properties of GaInNAs/GaAs quantum wells (QWs) with strain-compensated GaNAs layers grown by molecular beam epitaxy are investigated. The temperature-dependent PL spectra of GaInNAs/GaAs QW with and without GaNAs layers are compared and carefully studied. It is shown that the introduction of GaNAs layers between well and barrier can effectively extend the emission wavelength, mainly due to the reduction of the barrier potential. The PL peak position up to 1.41 μm is observed at the room temperature. After adding the GaNAs layers into QW structures, there is no essential deterioration of luminescence efficiency. N-induced localization states are also not remarkably influenced. It implies that with optimized growth condition, high-quality GaInNAs/GaAs QWs with strain-compensated GaNAs layers can be achieved.     

High-density carrier dynamics in Ge/Si quantum dots studied by time-resolved photoluminescence spectroscopy

We studied the temperature dependence of high-density carrier dynamics in as-grown and thermally annealed Ge quantum dots (QDs) in silicon crystals. In as-grown and thermally annealed samples, photoluminescence (PL) intensity exhibited a power-law dependence on the excitation intensity and its power-law index was ~ 0.7 at low temperatures. With increasing measurement temperature, PL intensity decreased and the index of the power-law function increased up to ~ 1.5, in which carrier recombination dynamics is dominated by a single carrier trapping. Moreover, in thermally annealed QDs, the index of the power law increased more rapidly than as-grown QDs, suggesting that the carrier recombination dynamics drastically changed in thermally annealed QDs. Effects of Ge/Si interface on high-density carrier recombination process are discussed.     

Anomalous temperature-dependent photoluminescence characteristic of as-grown GaInNAs/GaAs quantum well grown by solid source molecular beam epitaxy

The photoluminescence (PL) mechanisms of as-grown GaInNAs/GaAs quantum well were investigated by temperature-dependent PL measurements. An anomalous two-segmented trend in the PL peak energy vs. temperature curve was observed, which has higher and lower temperature-dependent characteristics at low temperature (5–80 K) and high temperature (above 80 K), respectively. The low and high-temperature segments were fitted with two separate Varshni fitting curves, namely Fit_low and Fit_high, respectively, as the low-temperature PL mechanism is dominated by localized PL transitions while the high-temperature PL mechanism is dominated by the e1–hh1 PL transition. Further investigation of the PL efficiency vs. 1/kT relationship suggests that the main localized state is located at 34 meV below the e1 state. It is also found that the temperature (80 K) at which the PL full-width at half-maximum changes from linear trend to almost constant trend correlates well with the temperature at which the PL peak energy vs. temperature curve changes from Fit_low to Fit_high.     

Low-density InAs QDs with subcritical coverage obtained by conversion of In nanocrystals

We report growth of InAs/GaAs quantum dots (QDs) by molecular beam epitaxy with low density of 2 μm^?2 by conversion of In nanocrystals deposited at low temperatures. The total amount of InAs used is about one monolayer, which is less than the critical thickness for conventional Stranski–Krastanov QDs. We also demonstrate the importance of the starting surface reconstruction for obtaining uniform QDs. The QD emission wavelength is easily tunable upon post-growth annealing with no wetting layer signal visible for short anneals. Microphotoluminescence measurements reveal well separated and sharp emission lines of individual QDs.     

引入Si掺杂层调控InGaAs/GaAs表面量子点的光学特性

在InGaAs/GaAs表面量子点(SQDs)的GaAs势垒层中引入Si掺杂层,以研究Si掺杂对InGaAs/GaAs SQDs光学特性的影响。荧光发光谱(PL)测量结果显示,InGaAs/GaAs SQDs的发光强烈依赖于Si掺杂浓度。随着掺杂浓度的增加, SQDs的PL峰值位置先红移后蓝移; PL峰值能量与激光激发强度的立方根依赖关系由线性向非线性转变;通过组态交互作用方法发现SQDs的PL峰位蓝移减弱;时间分辨荧光光谱显示了从非线性衰减到线性衰减的转变。以上结果说明Si掺杂能够填充InGaAs SQDs的表面态,并且改变表面费米能级钉扎效应和SQDs的荧光辐射特性。本研究为深入理解与InGaAs SQDs的表面敏感特性关联的物理机制和载流子动力学过程,以及扩大InGaAs/GaAs SQDs传感器的应用提供了实验依据。     

Growth of strain-compensated GaInNAs/GaAsP quantum wells for 1.3 μm lasers

Strain-compensated GaInNAs/GaAsP quantum well structures and lasers were grown by gas source molecular beam epitaxy using a RF-plasma nitrogen radical beam source. The optimal growth condition for the quantum well structure was determined based on room-temperature photoluminescence measurements. Effects of rapid thermal annealing (RTA) on the optical properties of GaInNAs/GaAsP quantum well structures as well as laser diodes are examined. It was found to significantly increase the photoluminescence from the quantum wells and reduce the threshold current density of the lasers, due to a removal of N induced nonradiative centers from GaInNAs wells.     

Self-assembled InAs quantum dots with two different matrix materials

The effects of matrix materials on the structural and optical properties of self-assembled InAs quantum dots (QDs) grown by a molecular beam epitaxy were investigated by atomic force microscopy, cross-sectional transmission electron microscopy (TEM), and photoluminescence (PL) spectroscopy. Cross-sectional TEM image indicated that the average lateral size and height of InAs QDs in a GaAs matrix on a GaAs substrate were 20.5 and 5.0 nm, respectively, which showed the PL peak position of 1.19 μm at room temperature. The average lateral size and height of InAs QDs buried in an InAlGaAs matrix on InP were 26.5 and 3.0 nm, respectively. The PL peak position for InP-based InAs QDs was around 1.55 μm at room temperature. If we only consider the size quantization effects, the difference in PL peak position between two QD systems with different matrices may be too large. The large difference in peak position can be mainly related to the QD size as well as the strain between the QDs and the matrix materials. The intermixing between the QDs and the matrix materials can partially change the In composition of QDs, resulting in the modification of the optical properties.     

The role of Sb in the molecular beam epitaxy growth of 1.30–1.55 μm wavelength GaInNAs/GaAs quantum well with high indium content

Sb-assisted GaInNAs/GaAs quantum wells (QWs) with high (42.5%) indium content were investigated systematically. Transmission electron microscopy, reflection high-energy electron diffraction and photoluminescence (PL) measurements reveal that Sb acts as a surfactant to suppress three-dimensional growth. The improvement in the 1.55 μm range is much more apparent than that in the 1.3 μm range, which can be attributed to the difference in N composition. The PL intensity and the full-width at half maximum of the 1.55 μm single-QW were comparable with that of the 1.3 μm QWs.     

Absorption and photoluminescence of PbS QDs in glasses

Optical properties of PbS quantum dots (QDs) precipitated inside the oxide glass matrix were investigated. Photoluminescence (PL) from the PbS QDs showed peak wavelengths located at 1170–1680 nm with widths of 150–550 nm. Radii of QDs in glasses were 2.3–4.7 nm depending upon the thermal treatment. Peak wavelengths of PL bands shifted as much as 70 nm as the temperatures and excitation irradiances increased. Calculated effective local temperatures indicated that these shifts of PL spectra were associated with local heating induced by the temperatures and laser beam.     

Formation of Ge-diffusion-suppressed GaAs layers and InAs quantum dots on Ge/Si substrates

Crystal growth of GaAs layers and InAs quantum dots (QDs) on the GaAs layers was investigated on Ge/Si substrates using ultrahigh vacuum chemical vapor deposition. Ga-rich GaAs with anti-site Ga atoms grown at a low V/III ratio was found to suppress the diffusion of Ge into GaAs. S-K mode QD formation was observed on GaAs layers grown on Ge/Si substrates with Ga-rich GaAs initial layers, and improved photoluminescence from 1.3 μm-emitting InAs QDs was demonstrated.     

Investigation on a two-pot solvothermal route for preparing high quality CdSe QDs

High quality zinc-blende CdSe quantum dots (QDs) have been synthesized through a novel two-pot solvothermal route employing non toxic and low cost materials without the use of inert atmosphere. The temperature is varied by maintaining the precursor amount a constant in all experiments. The X-ray powder diffraction (XRD) and high resolution transmission electron microscope (HRTEM) measurements indicate the occurrence of zinc-blende CdSe quantum dots (QDs) with the size ranging from 3.5 to 7 nm. The absorption spectra of the CdSe nanoparticles exhibit a blue shift, as an indication of the quantum confinement effect. The photoluminescence (PL) spectra of the CdSe nanoparticles confirm that the particles are monodisperse, size-tunable and possess enhanced luminescent property.     

Temperature quenching of photoluminescence of ordered GaInP2 alloy under different excitation densities

The photoluminescence (PL) emission from an epi‐structure containing an atomically ordered GaInP₂ layer and a GaAs layer was studied under excitation power densities of 0.03 – 3 W/cm²at temperatures of 10 to 300 K. The quenching of the integrated PL intensity from both: the GaInP₂and the GaAs layers is stronger under low excitation, than under high excitation density. The temperature dependence, however, have different shapes being the PL decay observed for the GaInP₂ layer stronger than that for the GaAs layer. Comparing the temperature dependence of the PL intensity from the ordered GaInP₂ and the GaAs layers under different excitation densities and analyzing them together, we conclude that the inhomogeneity of the ordered layer is responsible for the different temperature behavior of the GaInP₂ alloy PL emission. To explain the experimentally observed PL intensity temperature dependence an additional nonradiative recombination mechanism due to a thermally activated escape of the carriers from its confinement within regions of lower bandgap has to be taken into account. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Characterization of InAs quantum dots on lattice-matched InAlGaAs/InP superlattice structures

Self-assembled InAs quantum dots (QDs) in an InAlGaAs matrix, lattice-matched to InP substrate, have been grown by molecular beam epitaxy (MBE). Transmission electron microscopy (TEM), double-crystal X-ray diffraction (DCXRD) and photoluminescence (PL) are used to study their structural and optical properties. In InAs/InAlGaAs/InP system, we propose that when the thickness of InAs layer deposited is small, the random strain distribution of the matrix layer results in the formation of tadpole-shaped QDs with tails towards random directions, while the QDs begin to turn into dome-shaped and then coalesce to form islands with larger size and lower density to release the increasing misfit strain with the continuous deposition of InAs. XRD rocking curves showing the reduced strain with increasing thickness of InAs layer may also support our notion. The results of PL measurements are in well agreement with that of TEM images.     

Improvement of GaInNAsSb films fabricated by atomic hydrogen-assisted molecular beam epitaxy

The effect of incorporation of antimony in GaInNAs films grown by atomic hydrogen-assisted molecular beam epitaxy (MBE) has been investigated. We show that the rate of incorporation of N and In forming GaInNAs do not depend on the Sb beam flux. However, the incorporation of Sb is strongly dependent on the Sb/As₂ flux ratio. Introducing a small amount of Sb (<∼1%) significantly improves the photoluminescence (PL) emission efficiency of GaInNAs, but Sb concentration of >1% rapidly degrades the PL intensity, though a large redshift can still be achieved. Therefore, there is an optimum amount of Sb for the growth of low-strained GaInNAs films to improve the overall optical quality.     

Comparative study of electroluminescence from annealed amorphous SiC single layer and amorphous Si/SiC multilayers

Si quantum dots (Si QDs) films were prepared by annealing amorphous SiC single layer and amorphous Si/SiC multilayers fabricated in plasma enhanced chemical vapor deposition system. The microstructures were characterized by Raman spectroscopy as well as Fourier transforms infrared spectroscopy for both samples. It was found that Si QDs with average size of 2.7 nm were formed after annealing and the electroluminescence (EL) band centered at 650 nm can be observed at room temperature. The EL intensity from the Si/SiC multilayers was obviously improved by one order of magnitude and the corresponding EL band width was reduced compared with that from SiC single layer film. The improved electroluminescence behavior can be attributed to the formation of the denser Si QDs, good size distribution and the strong confinement effect of carriers in multilayerd structures.     

Amorphous carbon-based films with surface-plasmon-enhanced full-color photoluminescence

A series of amorphous carbon-based films were deposited on the nanostructured Ag layers to observe surface plasmon (SP) enhanced photoluminescence (PL). The dependence of PL peak wavelength and intensity on the film composition and the nanostructure of the Ag layers were systematically investigated. The PL wavelength was tuned from 442 nm to 635 nm by varying the carbon content of the as-deposited carbon-based films. The nanostructure of Ag layers varied from nanoparticles (NPs) to continuous films via process control. With the SPs generated at the carbon-based film/Ag layer interface, the PL intensity was found to be significantly enhanced with a peak enhancement factor of 6, and the light emission range of the composite films was extended to 434–653 nm. The dependence of PL intensity on the spectral overlap between the carbon-based films and plasmon resonant Ag layers, Ag surface morphology and the internal quantum efficiency (IQE) of the carbon-based films was discussed. The redshift of SP resonance with the increasing refractive index of the upper carbon-based films was observed.     

Ultrafast carrier capture in charged InAs quantum dots

We report theoretical and experimental results of our investigation on carrier capture and relaxation processes in undoped and modulation-doped InAs/GaAs self-assembled quantum dots (QDs). We find that carrier capture and relaxation in the ground state is faster in the modulation-doped quantum dots compared to the case in neutral dots at an excitation level as low as one electron–hole pair per dot. The ultrafast photoluminescence (PL) transient rise time observed in the charged dots is attributed to the relaxing of strained field induced by the presence of cold carriers in the dots. The Hamiltonian of electron’s interaction with local vibrating field and carrier capture time are also calculated.     

Si doping effect on self-organized InAs/GaAs quantum dots

In situ ultra high vacuum scanning probe microscopy (SPM) and low-temperature photoluminescence (PL) studies have been performed on Si-doped self-organized InAs/GaAs quantum dots samples to investigate the Si doping effects. Remarkably, when Si is doped in the sample, according to the SPM images, more small dots are formed when compared with images from undoped samples. On the PL spectra, high-energy band tail which correspond to the small dots appear, with increasing doping concentration, the integral intensity of the high-energy band tail account for the whole peak increase too. We relate this phenomenon to a model that takes the Si atom as the nucleation center for QDs formation.     

Growth and characterization of GaAs layers on polished Ge/Si by selective aspect ratio trapping

Epitaxial GaAs layers have been deposited on polished Ge film grown on exactly (0 0 1) oriented Si substrate by metal-organic chemical vapor deposition (MOCVD) via aspect ratio trapping (ART) method. Double-crystal X-ray diffraction shows that the full-width at half-maximum (FWHM) of the (4 0 0) reflection obtained from 1 μm GaAs is 140 arcsec. Scanning electron microscopy (SEM) of the GaAs layer surface shows that the amount of antiphase domain defects (APD) raised from GaAs/Ge interface using Ge ART on Si is dramatically reduced compared to GaAs layers grown on exact (0 0 1) Ge substrate. Defect reduction and Ge diffusion at vicinal GaAs/Ge interface were investigated via cross-section transmission electron microscopy (X-TEM) and secondary ion mass spectrometry (SIMS). Film morphology and optical properties were evaluated via SEM and room temperature photoluminescence (PL).