The dynamic behaviour of a piezoelectric actuator bonded to an anisotropic elastic medium

Surface-bonded piezoelectric actuators can be used to generate elastic waves for monitoring damages of composite materials. This paper provides an analytical and numerical study to simulate wave propagation in an anisotropic medium induced by surface-bonded piezocermic actuators under high-frequency electric loads. Based on a one-dimensional actuator model, the dynamic load transfer between a piezoceramic actuator and an anisotropic elastic medium under in-plane mechanical and electrical loading is obtained. The wave propagation induced by the surface-bonded actuator is also studied in detail by using Fourier transform technique and solving the resulting integral equations in terms of the interfacial shear stress. Typical examples are provided to show effects of the geometry, the material combination, the loading frequency and the material anisotropy of the composite upon the load transfer and the resulting wave propagation.     

Thermal Buckling Analysis of Size-Dependent FG Nanobeams Based on the Third-Order Shear Deformation Beam Theory

In this paper,the thermal effects on the buckling of functionally graded(FG) nanobeams subjected to various types of thermal loading including uniform,linear and non-linear temperature changes are investigated based on the nonlocal third-order shear deformation beam theory.The material properties of FG nanobeam are supposed to vary gradually along the thickness direction according to the power-law form.The governing equations are derived through Hamilton's principle and solved analytically.Comparison examples are performed to verify the present results.Obtained results are presented for thermal buckling analysis of FG nanobeams such as the effects of the power-law index,nonlocal parameter,slenderness ratio and thermal loading in detail.     

Three-dimensional thermoelastic analysis of finite length laminated cylindrical panels with functionally graded layers

Based on the 3D thermoelasticity theory, the thermoelastic analysis of laminated cylindrical panels with finite length and functionally graded (FG) layers subjected to three-dimensional (3D) thermal loading are presented. The material properties are assumed to be temperature-dependent and graded in the thickness direction. The variations of the field variables across the panel thickness are accurately modeled by using a layerwise differential quadrature (DQ) approach. After validating the approach, as an important application, two common types of FG sandwich cylindrical panels, namely, the sandwich panels with FG face sheets and homogeneous core and the sandwich panels with homogeneous face sheets and FG core are analyzed. The effect of micromechanical modeling of the material properties on the thermoelastic behavior of the panels is studied by comparing the results obtained using the rule of mixture and Mori–Tanaka scheme. The comparison studies reveal that the difference between the results of the two micromechanical models is very small and can be neglected. Then, the effects of different geometrical parameters, material graded index and also the temperature dependence of the material properties on the thermoelastic behavior of the FG sandwich cylindrical panels are carried out.     

A new super convergent thin walled composite beam element for analysis of box beam structures

In this paper, a new composite thin wall beam element of arbitrary cross-section with open or closed contour is developed. The formulation incorporates the effect of elastic coupling, restrained warping, transverse shear deformation associated with thin walled composite structures. A first order shear deformation theory is considered with the beam deformation expressed in terms of axial, spanwise and chordwise bending, corresponding shears and twist. The formulated locking free element uses higher order interpolating polynomial obtained by solving static part of the coupled governing differential equations. The formulated element has super convergent properties as it gives the exact elemental stiffness matrix. Static and free vibration analyses are performed for various beam configuration and compared with experimental and numerical results available in current literature. Good correlation is observed in all cases with extremely small system size. The formulated element is used to study the wave propagation behavior in box beams subjected to high frequency loading such as impact. Simultaneous existence of various propagating modes are graphically captured. Here the effect of transverse shear on wave propagation characteristics in axial and transverse directions are investigated for different ply layup sequences.     

Dynamic analysis of thick short length FGM cylinders

In this paper a thick short length hollow cylinder made of functionally graded materials (FGMs) under internal impact loading is considered. The inner surface of the cylinder is pure ceramic, the outer surface is pure metal, and the material composition varies continuously along its thickness. Finite Element Method based on Rayleigh-Ritz energy formulation has been applied to study the propagation of elastic waves in FG thick hollow cylinders. The Newmark direct integration method is applied to solve the time dependent equations. The time histories of displacements, stresses, wave propagation in two directions and velocities of radial stress wave propagation for various values of volume fraction exponent have been investigated. Also by using fast Fourier transform, the first natural frequencies for FG cylinders with simply-simply and clamped-clamped ends conditions are illustrated. The model has been compared with result of a plane strain FG thick hollow cylinder which is subjected to an internal impact loading, and it shows very good agreement.     

纵横载荷作用下功能梯度梁的弯曲和过屈曲

基于一阶非线性梁理论和物理中面概念,导出了纵横向载荷作用下功能梯度材料(FGM)梁非线性弯曲和过屈曲问题的控制方程,并获得了该问题的精确解;据此解研究了梯度材料性质、外载荷、横向剪切变形以及边界条件等因素对功能梯度材料梁非线性力学行为的影响,分析中假设功能梯度材料性质只沿梁厚度方向,并按成分含量的幂指数函数形式变化。结果表明:纵横载荷共同作用下,功能梯度梁的弯曲构形将有无限多个;随着梯度指数的增大,梁的变形减小,临界载荷升高;随着长高比的增大,横向剪切变形的影响减小。     

Investigation of thermo-elasto-plastic behavior of thick-walled spherical vessels with inner functionally graded coatings

Having high corrosion and thermal resistance characteristics, Functionally Graded Materials have been found wide range of applications in engineering fields. The analytical elasto-plastic solution for spherical vessels composed of outer homogenous part and inner FG coating under combined pressure and thermal loading is presented in this paper. Furthermore, the loading conditions resulted into onset of yielding from inner radius and fully plastic vessel are obtained. Material constituents in both homogenous and FG parts are assumed to be aluminum and SiC as metal matrix and ceramic particles, respectively. Although the amount of SiC particles in the homogenous part of vessel is assumed to be constant, it is varying in the radial direction of FG part based on the power law function. The results concerning two types of vessels with harder and softer FG coatings are also compared with those from homogenous vessel. Moreover, two dimensional finite element model was applied to simulate the process while the results were considered to verify the accuracy of the analytical solution. Generally, the results demonstrate that coating and grading behavior can really affect the stress distribution and yield pattern in the homogenous vessel with an inner FG coating.     

NiTi形状记忆合金裂纹尖端热力耦合行为研究

本文对NiTi形状记忆合金I型裂纹尖端热力耦合行为进行了数值仿真分析和实验验证。建立了包含相变和热力耦合的本构模型,通过有限元计算得到了裂纹尖端附近的纵向应变、马氏体体积分数和温度场分布,依据马氏体相变情况对裂纹尖端有效应力强度因子进行了修正,揭示了加载速率对形状记忆合金裂纹尖端有效应力强度影子的影响规律。参数研究表明,随着加载频率的增加,裂纹尖端附近温度逐渐升高,马氏体相变区域逐渐缩小,有效应力强度因子呈下降趋势,形状记忆合金表现出增韧效应,有助于减缓裂纹扩展。本研究结果对于揭示热力耦合作用下超弹性形状记忆合金疲劳裂纹扩展规律具有重要参考意义。     

Wave propagation and dynamic analysis of smoothly graded heterogeneous continua using graded finite elements

The dynamic behavior of smoothly graded heterogeneous materials is investigated using the finite element method. The global variation of material properties (e.g., Young’s modulus, Poisson’s ratio and mass density) is treated at the element level using a generalized isoparametric formulation. Three classes of examples are presented to illustrate this approach and to investigate the influence of material inhomogeneity on the characteristics of wave propagation pattern and stress redistribution. First, a cantilever beam example is presented for verification purposes. Emphasis is placed on the comparison of numerical results with analytical ones, as well as modal analysis for beams with different material gradation profiles. Second, wave propagation patterns are explored for a fixed-free slender bar considering homogeneous, bi-material, tri-layered and smoothly graded materials (steel/alumina), which also provide further verification of the numerical procedures. Comparison of stress histories in these samples indicates that the smooth transition of material gradation considerably alleviates the stress discontinuity in the bi-material system (with sharp interface). Third, a three-point-bending epoxy/glass graded beam specimen is investigated for validation purposes. The beam is graded along the height direction. Stress evolution history at a location of interest is analyzed in detail, which not only reveals the dependence of stress evolution on material gradation direction, but also provides information predictive of potential material failure time for graded beams with different material gradation profiles. Jointly, these three classes of examples provide proper verification and validation for the present numerical techniques.     

A mesoscale investigation of strain rate effect on dynamic deformation of single-crystal copper

A combined finite element (FE) simulation and discrete dislocation dynamics (DD) approach has been developed in this paper to investigate the dynamic deformation of single-crystal copper at mesoscale. The DD code yields the plastic strain based on the slip of dislocations and serves as a substitute for the 3D constitutive form used in the usual FE computation, which is implemented into ABAQUS/Standard with a user-defined material subroutine. On the other hand, the FE code computes the displacement and stress field during the dynamic deformation. The loading rate effects on the yield stress and the deformation patterning of single-crystal copper are investigated. With the increasing of strain rate, the yield stress of single-crystal copper increases rapidly. A critical strain rate exists in each single-crystal copper block for the given size and dislocation sources, below which the yield stress is relatively insensitive to the strain rate. The dislocation patterning changes from non-uniform to uniform under high-strain-rate. The shear stresses in the bands are higher than that in the neighboring regions, which are formed shear bands in the crystal. The band width increases with the strain rate, which often take places where the damage occurs.     

Development and validation of a viscoelastic finite element model of an L2/L3 motion segment

The prediction of the time dependent response of the spine to dynamic loading conditions is essential in understanding the injury mechanisms leading to occupationally related low back disorders (OLBD). Many previous finite element (FE) models of the lumbar spine have over-simplified the geometry and the material properties of their elements, yielding results limited generalizability. This study reports on the development and validation of a nonlinear viscoelastic FE model that can quantify the mechanical responses of the L2/L3 motion segment to time varying external loads. This model was developed by consideration of the intrinsic material properties of its individual constituents. A piecewise parameter identification method was adopted due to the inherent complexity in determining the role and contribution of each element to the overall behavior of the motion segment. The results of simulation of four loading conditions (quasistatic, constant loading rate, creep and cyclic relaxation) showed a satisfactory agreement with experimental observations in the literature. The detailed estimates of the state of stress/strain of this validated FE model can be used to test the role of epidemiological risk factors such as prolonged awkward posture, speed of lift (strain rate effect) and complex repetitive loading in OLBD.     

梯形应力脉冲在弹性杆中的传播过程和几何弥散

在应力波传播过程中,几何弥散效应往往难以避免.对应力波在弹性杆中传播的几何弥散效应进行解析分析,对于基础波动问题研究以及材料动态力学行为表征等课题,显得至关重要.本文简单说明了弹性杆中考虑横向惯性修正的一维 Rayleigh-Love应力波理论,概述了其波动控制方程的变分法推导过程;针对 Hopkinson杆实验中常用的梯形应力加载脉冲,建立了相应的偏微分方程初边值问题的求解模型,并运用 Laplace变换方法研究了脉冲在杆中传播的几何弥散现象;根据留数定理进行 Laplace反变换,给出了杆中不同位置和时刻的应力波的级数形式解析解,分析了计算项数对结果收敛性的影响;将解析计算结果与采用三维有限元数值模拟的计算结果进行对比,两者吻合程度良好,从而证明 Rayleigh-Love横向惯性修正理论可以有效地表征典型 Hopkinson杆实验中的几何弥散效应.在此基础上围绕梯形加载脉冲的弥散效应进行参数研究,定量描述了传播距离、泊松比、脉冲斜率等参数的影响.本文给出的 Rayleigh-Love杆在梯形加载条件下的解析解,揭示了几何弥散效应的本质规律,可以用于实际实验的弥散修正过程.      

钢筋混凝土梁受弯破坏过程的细观数值模拟研究

在细观层次上将混凝土视为由粗骨料、硬化水泥砂浆及界面粘结带组成的三相非均质复合材料,能够较好地模拟混凝土加载时的裂缝扩展过程和分布规律。本文采用细观刚体弹簧元法模拟了钢筋混凝土梁的弯曲受力性能和破坏过程,加载方式采用两点对称加载。数值计算得到了钢筋混凝土梁的破坏形态和荷载一变形曲线,并分析了受力过程中纵向钢筋的应力变化。与试验结果对比表明,细观刚体弹簧元法可以有效模拟钢筋混凝土梁的裂缝开展过程、破坏形态和荷载一变形响应。     

Four-point combined DE/FE algorithm for brittle fracture analysis of laminated glass

A four-point combined DE/FE algorithm is proposed to constrain the rotation of a discrete element about its linked point and analyze the cracks propagation of laminated glass. In this approach, four linked points on a discrete element are combined with four nodes of the corresponding surface of a finite element. The penalty method is implemented to calculate the interface force between the two subdomains, the finite element (FE) and the discrete element (DE) subdomains. The sequential procedure of brittle fracture is described by an extrinsic cohesive fracture model only in the DE subdomain. An averaged stress tensor for granular media, which is automatically symmetrical and invariant by translations, is used to an accurate calculation of the averaged stress of the DE. Two simple cases in the elastic range are given to certify the effectiveness of the combined algorithm and the averaged stress tensor by comparing with the finite element method and the mesh-size dependency of the combined algorithm and the cohesive model is also investigated. Finally, the impact fracture behavior of a laminated glass beam is simulated, and the cracks propagation is compared with experimental results showing that the theory in this work can be used to predict some fracture characteristics of laminated glass.     

Microstructural modeling of asphalt concrete using a coupled moisture–mechanical constitutive relationship

The coupled effect of moisture diffusion and mechanical loading on the microstructure of asphalt concrete is studied. The traditional Continuum Damage Mechanics (CDM) framework is modified to model detrimental effects of moisture and mechanical loading. Adhesive/cohesive moisture-induced damage constitutive relationships are proposed to describe the time-dependent degradation of material properties due to moisture. X-ray two-dimensional (2D) computed tomography-imaging technique is used to construct finite element (FE) microstructural representation of a typical dense-graded asphalt concrete. After being calibrated against pull-off experiments, the proposed moisture-induced damage constitutive relationship, which is coupled to thermo-viscoelastic–viscoplastic–viscodamage mechanisms, is used to simulate the microstructure of asphalt concrete. Simulation results demonstrate that the generated 2D FE microstructural representation along with the coupled moisture–mechanical constitutive relationship can be effectively used to model the overall thermo-hygro-mechanical response of asphalt concrete.     

Assessment of assembly shape and geometric effects on amplification of shear waves using discrete element method

The discrete element method (DEM) is a capable tool used to simulate shear wave propagation in granular assemblies for many years. Researchers have studied assembly shapes such as rectangles (in 2D simulations) or cylinders and cubes (in 3D simulations). This paper aimed to qualify the effect of assembly shape on the shear wave propagation and maximum amplification in the vertical plane (horizontal and vertical directions) caused by this propagation. To this end, shear wave propagations in different assembly shapes such as rectangle, trapezium, and triangle with rigid boundary conditions were simulated. A sine wave pulse was applied with a point source by moving a particle as the transmitter particle. To evaluate the shear wave velocity of the assemblies, the transmitter and receiver particles were simulated. All the simulations were performed with 2D DEM which is a useful tool to determine the amount and location of the maximum amplification factor of the assembly in both horizontal and vertical directions. An advantage of this study was assessing the effect of parameters such as input wave frequency, assembly height, shape, and aspect ratios on the amplification of the input waves.     

Modeling the effects of material non-linearity using moving window micromechanics

In the analysis of materials with random heterogeneous microstructure the assumption is often made that material behavior can be represented by homogenized or effective properties. While this assumption yields accurate results for the bulk behavior of composite materials, it ignores the effects of the random microstructure. The spatial variations in these microstructures can focus, initiate and propagate localized non-linear behavior, subsequent damage and failure. In previous work a computational method, moving window micromechanics (MW), was used to capture microstructural detail and characterize the variability of the local and global elastic response. Digital images of material microstructure described the microstructure and a local micromechanical analysis was used to generate spatially varying material property fields. The strengths of this approach are that the material property fields can be consistently developed from digital images of real microstructures, they are easy to import into finite element models (FE) using regular grids, and their statistical characterizations can provide the basis for simulations further characterizing stochastic response. In this work, the moving window micromechanics technique was used to generate material property fields characterizing the non-linear behavior of random materials under plastic yielding; specifically yield stress and hardening slope, post yield. The complete set of material property fields were input into FE models of uniaxial loading. Global stress strain curves from the FE–MW model were compared to a more traditional micromechanics model, the generalized method of cells. Local plastic strain and local stress fields were produced which correlate well to the microstructure. The FE–MW method qualitatively captures the inelastic behavior, based on a non-linear flow rule, of the sample continuous fiber composites in transverse uniaxial loading.     

Mixed-mode fracture analysis of orthotropic functionally graded materials under mechanical and thermal loads

Mixed-mode fracture problems of orthotropic functionally graded materials (FGMs) are examined under mechanical and thermal loading conditions. In the case of mechanical loading, an embedded crack in an orthotropic FGM layer is considered. The crack is assumed to be loaded by arbitrary normal and shear tractions that are applied to its surfaces. An analytical solution based on the singular integral equations and a numerical approach based on the enriched finite elements are developed to evaluate the mixed-mode stress intensity factors and the energy release rate under the given mechanical loading conditions. The use of this dual approach methodology allowed the verifications of both methods leading to a highly accurate numerical predictive capability to assess the effects of material orthotropy and nonhomogeneity constants on the crack tip parameters. In the case of thermal loading, the response of periodic cracks in an orthotropic FGM layer subjected to transient thermal stresses is examined by means of the developed enriched finite element method. The results presented for the thermally loaded layer illustrate the influences of the material property gradation profiles and crack periodicity on the transient fracture mechanics parameters.     

Non-linear analysis of functionally graded circular plates under asymmetric transverse loading

Based on the first-order shear deformation plate theory with von Karman non-linearity, the non-linear axisymmetric and asymmetric behavior of functionally graded circular plates under transverse mechanical loading are investigated. Introducing a stress function and a potential function, the governing equations are uncoupled to form equations describing the interior and edge-zone problems of FG plates. This uncoupling is then used to conveniently present an analytical solution for the non-linear asymmetric deformation of an FG circular plate. A perturbation technique, in conjunction with Fourier series method to model the problem asymmetries, is used to obtain the solution for various clamped and simply supported boundary conditions. The material properties are graded through the plate thickness according to a power-law distribution of the volume fraction of the constituents. The results are verified by comparison with the existing results in the literature. The effects of non-linearity, material properties, boundary conditions, and boundary-layer phenomena on various response quantities in a solid circular plate are studied and discussed. It is found that linear analysis is inadequate for analysis of simply supported FG plates which are immovable in radial direction even in the small deflection range. Furthermore, the responses of FG materials under a positive load and a negative load of identical magnitude are not the same. It is observed that the boundary-layer width is approximately equal to the plate thickness with the boundary-layer effect in clamped FG plates being stronger than that in simply supported plates.     

Shear wave velocity in sand considering the effects of frequency based on particle contact theory

Since the shear waves involved in in-situ and laboratory measurement methods vary significantly in terms of the frequency range, it is necessary to consider the effects of frequency on the shear wave velocity. In this study, sand particles are assumed to be spherical solid particles with an equal radius and identical material properties, and sand skeletons are regarded as granular aggregations generated through the random packing of sand particles. It is also assumed that the sand particles only undergo elastic deformation during shear wave propagation. Based on a spherical particle model, a formula is obtained for calculating the shear wave velocity in sand, with the shear wave frequency as an extra influencing parameter. The quantitative calculations demonstrate that the shear wave velocity decreases with an increase of sand porosity, and accelerates with increases of vertical effective stress and elastic modulus of the sand particles. It is also indicated that both the particle density and Poisson’s ratio of the sand particles have negligible effects on the shear wave propagation. The frequency dispersion characteristics of shear wave propagating in sand are also discussed. Moreover, the critical frequency is defined and its analytical expression is derived. The calculation results obtained using the proposed equations agree well with the in-situ measurement results and bender element test data.