温度对超薄铜膜疲劳性能影响的分子动力学模拟

用嵌入原子势的分子动力学方法模拟了温度对超薄铜膜疲劳性能的影响. 通过模拟, 首先给出了超薄铜膜的总能及应力随循环周次的变化曲线; 根据叠加经验式得出的叠加量随循环周次变化曲线, 判断出各种恒定温度下超薄铜膜的疲劳寿命. 由 200–400 K温度范围内超薄铜膜的疲劳寿命-温度变化曲线, 可以发现存在两个温度区域: 在约370 K以下, 超薄铜膜的疲劳寿命随温度升高缓慢增加, 而在约370 K以上增加较快. 建立了模型并用位错演化机制解释了超薄铜膜疲劳寿命的温度依赖关系. 关键词： 分子动力学 疲劳 温度效应 位错     

Cyclic deformation and fatigue cracking behaviors of Cu–28wt%Ag binary alloy

The cyclic deformation and fatigue cracking behaviors of coarse-grained Cu–28wt%Ag binary alloy were investigated under axial plastic strain amplitudes ranging from 10^?4 to 7.5 × 10^?4. It was found that the cyclic stress of the Cu–Ag alloy increased rapidly in the initial tens of cycles and became saturation with further cyclic deformation. The cyclic saturation stress increased with increasing the plastic strain amplitude. The interfaces are classified into two categories based on the orientations of the eutectic and the dendrites, i.e. type I and type II interfaces. The surface damage morphologies show that fatigue cracks normally nucleated either along the type I interfaces or along the slip bands (SBs), while no cracking occurred along the type II interface. Fatigue striations with different spacings appeared on the fracture surface, and secondary cracks along the striations were also observed. Based on the experimental results, the cyclic deformation and fatigue cracking behavior of the Cu–Ag binary alloy were discussed in detail.     

Fatigue of lead titanate and lead zirconate titanate thin films

The fatigue of lead titanate and lead zirconate titanate ferroelectric thin films, i.e., a change in the polarization as a function of the number of switching cycles in an external electric field, is investigated experimentally. The threshold numbers of switching cycles are determined to be 10¹⁰–10¹¹ for the lead titanate films and 10⁹–10¹⁰ for the lead zirconate titanate films. It is shown that a change in the temperature does not substantially affect the threshold number of switching cycles at which the switched polarization decreases drastically. However, an increase in the external field strength leads to a noticeable decrease in the threshold number of switching cycles. The process of fatigue is accompanied by an increase in the coercive field and the internal bias field. It is established that, as the number of switching cycles increases, the internal bias field changes more significantly as compared to the coercive field. The absence of a change in the phase composition in repeatedly switched samples indicates that the fatigue processes have a nonchemical nature. The anomaly observed in the frequency dependence of the permittivity in the frequency range 10⁶–10⁷ Hz due to the domain structure disappears after multiple switching cycles. This suggests that the observed fatigue phenomenon has a domain nature.     

Incipient plasticity and voids nucleation of nanocrystalline gold nanofilms using molecular dynamics simulation

In this study, the incipient plasticity and voids nucleation of nanocrystalline gold were investigated using a molecular dynamics simulation. The effects of mean grain size and temperature were evaluated in terms of the material's stress-strain diagram, Young's modulus, yield strength, common-neighbor analysis, slip vectors, and deformation behaviors. From the stress-strain diagram, at 300?K, the maximum stress value corresponding to a grain size of 3.2?nm was much lower and the stress curve was clearly different from those corresponding to other grain sizes. Young's modulus increased with increasing mean grain size. The inverse Hall–Petch relation was observed. The slip was the main deformation behavior at a mean grain size of 3.2?nm. Moreover, the internal stress was more pronounced with increasing temperature. At 700?K, the main deformation area range was concentrated in the lattice at the middle of the samples, resulting in an almost force–induced structural transformation phenomenon in the middle. Void damage occurred at the junction of three–grain boundaries during the tensile process. With decreasing mean grain size, the less internal differential slip was generated under the same temperature and strain conditions.     

Nanoscale Kirkendall Effect and Oxidation Kinetics in Copper Nanocrystals Characterized by Real‐Time,In Situ Optical Spectroscopy

The low‐temperature oxidation of ≈10 nm diameter copper nanocrystals is characterized using in situ UV–vis absorbance spectroscopy and observed to lead to hollow copper oxide shells. The kinetics of the oxidation of solid Cu nanocrystals to hollow Cu₂O nanoparticles is monitored in real‐time via the localized surface plasmon resonance response of the copper. A reaction‐diffusion model for the formation of hollow nanoparticles is fit to the measured time for complete Cu nanocrystal oxidation, and is used to quantify the diffusion coefficient of Cu in Cu₂O and the activation energy of the oxidation process. The diffusivity measured here in single‐crystalline nanoscale systems is 1–5 orders of magnitude greater than in comparable systems in the bulk, and have an Arrhenius dependence on temperature with an activation energy for diffusion of 37.5 kJ mol^?1 for 85 °C ≤ T ≤ 205 °C. These diffusion parameters are measured in some of the smallest metal systems and at the lowest oxidation temperatures yet reported, and are enabled by the unique nanoscale single‐crystalline material and the in situ characterization technique.     

Estimation of fatigue life of railway bridges under traffic loads

Random modelling of railway bridge loading enables fatigue damage to be calculated on the basis of the cumulative damage theory of Palmgren-Miner and the classification of the stress-time history by means of the “rain-flow” counting method. The results of calculations are the mean value of the damage and the standard deviation of the stresses, and thus an estimation of the bridge fatigue life. Accordingly the bridge life is dependent on the number of stress cycles and their distribution, the standard deviation of stresses, and on the shape of the Wöhler curve. Bridge life increasing span and decreases with an increasing traffic load. Results are presented as obtained in a detailed study of the effects on the bridge life of different parameters (vehicle speed, damping of bridge vibrations, variability in length and time of the moving load and its magnitude, number of stress cycles and their distribution). The equivalent damage method (the λ_T-method) in the integral form enables one to compare the effects of the traffic loads with those of the standard loading.     

Strain bursts during cyclic deformation and coarse slip

Summary Single crystals of 99·98% copper were cyclically deformed in push-pull at 50 cps by an electrodynamical vibrator designed to make the stress amplitude independent of changes in plastic compliance of the specimen. Over a period ofN cycles (280 < < N < 10⁶) the stress amplitude was increased linearly with time up to 3·2 kp/mm² giving a fatigue life of 10⁶. During this monotonic increase of stress amplitude withN > 5000 the plastic strain amplitude did not rise monotonically but showed about 20 regularly spaced, strong maxima. These slip bursts lasted typically about 50 cycles and originated from slip distributed throughout the specimen. The next burst occurred when the stress amplitude had increased by about 12%. Observations of the influence of the rate of stress amplitude increase, unidirectional prestrain, and orientation are reported. If one stops increasing the stress amplitude between two strain bursts at a stress amplitude of only about 1·5 kp/mm² and then pulls the specimen unidirectionally, a yield point with a lower yield stress is observed just at the stress where the next strain burst would have occurred had the increase of cycling stress been continued. During the subsequent yield elongation in a unidirectional test there form very strong (0·3 m) and widely spaced (5 m) slip lines. This coarse slip cannot be explained in terms of point defect clusters at the very beginning of a fatigue test of a pure metal. All of these observations can, however, be interpreted in terms of the formation and dissociation of dislocation dipoles formed by mutual trapping of dislocations of opposite sign on different slip planes. It seems reasonable that the main part of cyclic hardening is due to this mutual trapping even in tests performed so that no bursts occur. This is in agreement with the ample evidence supplied by electron microscopy that almost nothing but dipoles are observed after cyclic deformation.Published in Z. f. Metallkunde59 (1968), 927.     

高导无氧铜的高压与高应变率本构模型研究

基于Y/G及G/B为常数的假设,构建了高导无氧铜的七种高压与高应变率本构模型.对于高导无氧铜进行了平面冲击波试验,采用纵向与横向锰铜应力计记录了试件中的纵向与横向应力,从而得到了屈服应力历史.用所构建的七种本构模型进行了数值模拟,并与高导无氧铜的平面冲击波试验结果进行比较.结果表明,平面冲击波载荷下高导无氧铜的屈服强度对于压力、密度、温度以及塑性应变的依赖性是本构描述的关键.而由Hopkinson试验取得的高导无氧铜高应变率本构模型,并不适合描述平面冲击波载荷下的本构特性. 关键词： 本构模型 高导无氧铜 平面冲击波试验 锰铜应力计     

NiTi合金中应力诱导的I/C相变及其界面动力学的研究

在改装了的拉力试验机上,以不同的拉伸速率ε(0.79—18×10^-5s^-1)进行加、卸载试验,并用中间扭摆和四端电位法同时测量了Ni-49at％Ti合金丝在应力诱导I/C相变过程的内耗Q^-1、模量M/M₀、电阻率ρ/ρ₀和应力-应变曲线。研究了应力循环和应变速率的影响。在Q^-1-ε曲线上出现Q^-1峰,而在f²-ε曲线上出现与之相对应的模量极小。内耗峰的高度Q_p^-1和模量亏损值均随ε增大而增大。根据界面动力学模型和内耗的实验数据,计算得应力诱导I/C相变过程界面的动力学关系为V=V^*(△G—△G_R)^m,V^*和m为动力学参数,△G_R为相变过程中运动相界面所受的阻力,计算得△G_R≈1cal/mol。讨论了内耗和模量亏损、软模效应之间的关系。 关键词：     

Thermomechanical response of an Ni–Ti–Cr shape-memory alloy at low and high strain rates

The thermomechanical response of an Ni–Ti–Cr shape-memory alloy is investigated at various initial temperatures, over a wide range of strain rates, using an Instron hydraulic testing machine and one of the modified split-Hopkinson-bar systems at the Center of Excellence for Advanced Materials, University of California, San Diego. The transition stress for the stress-induced martensite formation is observed to be quite sensitive to the initial deformation temperature, but the yield stress of the resulting martensite is not. The linear transition stress–temperature relation with a slope of 8.5?MPa?K^?1, obtained in a quasistatic loading regime, seems to remain valid for strain rates up to 500–700?s^?1. The transition stress and the yield stress of the stress-induced martensite show strain-rate sensitivity, increasing monotonically with increasing strain rate. There exists a certain critical strain rate at which the transition stress equals the yield stress of the material. This critical strain rate determines the material's deformation behaviour; the material deforms by the formation of stress-induced martensites and their subsequent yielding, when the strain rate is less than this critical value, and through dislocation-induced plastic slip of the parent austenite, when the strain rate exceeds the critical value. It appears that the critical strain rate increases slightly with decreasing initial temperature.     

63Cu NMR analysis of microstructure evolution in Al–Cu–Mg alloys

⁶³Cu NMR spectroscopy has been used to detect metastable Guinier–Preston–Bagaryatsky (GPB) zones and nanoscale precipitates of equilibrium S-phase (Al₂CuMg) in dilute alloys of aluminium containing copper and magnesium with compositions which lie in the α?+?S phase field. The GPB zones are observed to form rapidly at room temperature with a time development closely related to the Vickers hardness. The final development of S-phase in the alloy has been confirmed by the observation of a line shape in the alloy identical to that observed in a specimen prepared from stoichiometric Al₂CuMg. Analysis of the hyperfine structure of the ⁶³Cu line shape observed for S-phase shows clearly that two Cu sites are present with approximately equal population. This result suggests that possibly two crystallographically distinct Al₂CuMg phases are present. The addition of small amounts of silver to Al–Cu–Mg alloys in the α?+?θ phase field is known to induce the formation of Ω-phase: a slight distortion of tetragonal θ-phase Al₂Cu. A hyperfine-structured ⁶³Cu line shape assigned to Ω-phase, indicating one distinct Cu site, has been observed in two separate Al–1.7?at.%?Cu–0.33?at.%?Mg alloys containing 0.1 and 0.18?at.%?Ag, but not in the same Al–Cu–Mg alloy without Ag.     

Effect of alternating electric current on the nanoindentation of copper

Electromechanical interaction determines the structural reliability of electronic interconnects. Using the nanoindentation technique, the effect of alternating electric current on the indentation deformation of copper strips was studied for the indentation load in a range of 100 to 1600???N at room temperature. During the test, an alternating electric current of the electric current density in a range of 1.25 to 4.88?kA/cm² was passed through the copper strips. The indentation results showed that the reduced contact modulus decreased linearly with increasing the electric current density. The indentation hardness decreased with increasing the indentation deformation, demonstrating the normal indentation size effect. Using the model of strain gradient plasticity, we found that the strain gradient underneath the indentation decreased slightly with increasing the electric current density for the same indentation depth.     

Low-temperature plasticity in nanocrystalline titanium and copper

The stress-strain compressive curves, temperature dependences of the yield stress, and small-inelastic-strain rate spectra of coarse-grained and ultrafine-grained (produced by equal-channel angular pressing) titanium and copper are compared in the temperature range 4.2–300 K. As the temperature decreases, copper undergoes mainly strain hardening and titanium undergoes thermal hardening. The temperature dependences of the yield stress of titanium and copper have specific features which correlate with the behavior of their small-inelastic-strain rate spectra. Under the same loading conditions, the rate of microplastic deformation of ultrafine-grained titanium is lower than that of coarse-grained titanium and the rate peaks shift toward high temperatures. The deformation activation volumes of titanium samples differing in terms of their grain size are (10–35)b ³, where b is the Burgers vector magnitude. The dependences of the yield stress on the grain size at various temperatures are satisfactorily described by the Hall-Petch relation.     

中子衍射法研究单晶镍基高温合金热机械疲劳引起的应力和晶格错配

采用中子衍射法对热机械疲劳后的单晶镍基高温合金样品内部中心点进行了实验测量,数据处理采用了双相叠加峰和单峰分析两种方法,计算得到了样品材料的宏观等效应力、应力偏量、γ相和γ′相的等效应力和晶格错配度等.实验结果表明,两种分析方法得到的宏观等效应力基本一致.在热机械疲劳循环100周出现最大宏观等效应力和应力偏量,此时位错等微缺陷达到饱和,偏离中心点处γ′相应力减小显著;在热机械疲劳开始阶段负错配度明显减小,随循环周次增多基体塑性应变累积又使负错配度以每次81×10^-6的速度逐渐线形增大. 关键词： 中子衍射 单晶高温合金 等效应力 应力偏量     

Low-cycle fatigue small crack initiation and propagation behaviour of cast magnesium alloys based on in-situ SEM observations

In-situ observations on the initiation and propagation behaviour of low-cycle fatigue small cracks in cast magnesium–aluminium alloys (AM50 and AM60B) were carried out with scanning electron microscopy (SEM) to elucidate the resistance to fatigue cracking and to evaluate the fatigue small crack growth rate accurately and quantitatively. The results indicate that the fatigue small cracks formed preferentially on β-phase (Mg₁₇Al₁₂) boundaries at room temperature. In addition, the effects of the parameters of stress levels in low-cycle fatigue and temperatures as well as microstructure on fatigue small crack propagation behaviour are revealed. The variation of crack open displacement (COD) with stress levels and cycles at elevated temperature shows that it is unsuitable to estimate the fatigue small crack growth rate of cast magnesium alloys using conventional measurement methods such as the plastic-replica technique due to the obvious difference between microscopic cracks in the open and closed states. Stabilized crack propagation behaviour is limited to cases where the physical crack length is less than 1?mm in low-cycle fatigue.     

Characterization of new cellulose sansevieria ehrenbergii fibers for polymer composites

Natural cellulose fibers were newly identified from the sources of sansevieria ehrenbergii plant. These fibers were extracted using the mechanical decortication process. The hierarchical cell structure of the plant and fibers was analyzed using scanning electron microscope, optical microscope, Fourier transforms infrared, and X-ray diffraction. The density and diameter of the fibers were found to be approximately 0.887?g/cm³ and 10–250?μm, respectively. The various chemical compositions were analyzed and compared with other natural fibers. The thermal stability of the fiber was examined through thermogravimetric analysis/differential thermogravimetric analysis (DTG). The maximum peak temperature was obtained at 333.02?°C in DTG curve. The raw fibers exhibited a tensile strength of 50–585?MPa, an elongation at break of 2.8–21.7%, a Young’s modulus of 2.5–7.5?GPa, and a corrected compliances Young’s modulus of 2.5–7.8?GPa.     

Effect of Cyclic Deformation on Magnetorheological Elastomers

采制备了铁颗粒含量分别是60%,70%和80%的三种材料,在应变幅值为50%,75%和100%的循环加载条件下,利用改进后的动态力学分析仪测试了循环加载后材料的储能模量和损耗模量. 结果显示铁颗粒含量为70%和80%的样品,其储能模量和损耗模量都和循环加载的幅值以及循环加载的次数有关,铁颗粒含量为80%样品受加载条件的影响尤其明显. 但铁颗粒含量为60%的样品,其性能却与循环加载的幅值和次数无关. 为了更好的研究磁流变弹性体受循环加载后的性能,样品还进行了准静态拉伸测试,并用扫描电镜对测试的样品进行了原位观察.     

Effect of copper addition on some properties of rapidly solidified lead-free Sn–-10 wt% Zn alloys

This study aimed at investigating the effect of adding copper (Cu) on some properties of the lead-free alloys which rapidly solidified from melt. X-ray analysis, hardness, elastic modulus, electrical conductivity and resistivity were studied. The results indicated that the alloy hardness and elastic modulus improved by increasing the copper (Cu) content and decreasing the zinc (Zn) content. The electrical conductivity ranged from 0.250 to 0.847?×?10⁷ ohm^?1 m^?1 for the alloy under study. The electrical resistivity increases linearly with temperature until the melting point is reached. The residual resistivity results from disturbances in the lattice rather than caused by thermal vibration and the most drastic increases in the residual resistivity are caused by foreign atoms in solid solution with matrix metal. The electrical resistivity values ranged from 11.8 to 40?×?10^?8 ohm m, when the copper content changed from 0.0 to 2.0 wt% and zinc changed from 8.0 to 10.0 wt%.     

Kinetics of high-temperature deformation of polycrystalline OFHC copper and the role of dislocation core diffusion

The mechanisms of the high-temperature deformation of oxygen-free high-conductivity (OFHC) copper have been evaluated over a wide temperature (300–950°C) and strain rate (0.001–100?s^?1) regime. The stress–strain behaviour in hot compression is typical of the occurrence of dynamic recrystallization with an initial peak in the flow stress followed by a steady state, preceded by oscillations at lower strain rates and higher temperatures. The results are analysed using the kinetic rate equation involving a hyperbolic sine relation of the steady-state flow stress with the strain rate. In the temperature and strain rate range covering 500–950°C and 0.001–10?s^?1, a stress exponent of 5 and an apparent activation energy of 145?kJ/mol were evaluated from this analysis. The power law relationship also yielded similar values (5.18 and 152?kJ/mol, respectively). On the basis of these parameters, the rate-controlling mechanism is suggested to be dislocation core diffusion. The flow stress for the OFHC copper data reported by earlier investigators for different oxygen contents is consistent with the above analysis and revealed that an oxygen content of less than about 40?ppm does not have any significant effect on the core diffusion since it is too low to ‘clog’ the dislocation pipes. At strain rates greater than 10?s^?1 and in the temperature range 750–950°C, the stress exponent is about 3.5 and the apparent activation energy is 78?kJ/mol, which suggests that the plastic flow is controlled by grain boundary diffusion.