Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Jump rate and linear distance of vacancy on the structure and electrical conductivity of Ni0.65Zn0.35CuxFe2−xO4 ferrites

Ferrite compositions of Ni_0.65Zn_0.35Cu_xFe_2−xO₄ (0⩽x<1) were examined using X-ray analysis. The effect of the linear distance of vacancy jumping on the lattice parameter was studied. The jump rate of vacancy increased with increasing Cu concentration. The increase of jump rate of vacancy enhanced the linear distance which increased the conductivity and mobility of the charge carriers. The majority of charge carriers of our systems are holes. The estimated linear distance of each jump was 2.86×10⁻⁷ m. The decrease of thermal conductivity was attributed to the increase of the jump rate and also the linear distance. The formation of oxygen vacancies during the substitution of Cu²⁺ ions for Fe³⁺ ions helped the internal stress to decrease the lattice parameter. Because the ionic radius of O²⁻ (0.136 nm) is larger than that of Fe³⁺ (0.067 nm) ion.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Spin reorientation and magnetocrystalline anisotropy of (Nd1−xDyx) Fe14B

Spin reorientation and magnetocrytalline anisotropy of (Nd_1−xDy_x)₂Fe₁₄B (x=0.25, 0.5, 0.75) have been studied from mangetization curves of magnetically aligned powders. In (Nd_1−xDy_x)₂Fe₁₄B, the spin reorientation temperature (T_SR) decreases linearly on increasing Dy-substitution from 135 to 56 K with the ratio of ΔT_SR=−1.11 K/Dy at% in the composition range of 0⩽x⩽0.75. The spin reorientation angle at 4.2 K decreases on Dy-substitution from 30.4° at x=0 to 14.7° at x=0.75. From the investigation of the magnetocrystalline anisotropy at 4.2 K, the disappearance of the spin reorientation for compositions x≳0.85 is expected.     

Defect equilibria and partial molar properties of (La,Sr)(Co,Fe)O3−δ

The oxygen nonstoichiometry δ of La_1−xSr_xCo_1−yFe_yO_3−δ (x = 0.6 and y = 0.2, 0.4) was investigated by thermogravimetry in the range 703 ≤ T/°C ≤ 903 and 1E−5 < pO₂/atm < 1. The oxygen deficit increases with increasing T and decreasing pO₂. Electronic conductivities σ were measured as a function of pO₂ in the range 1E−5 < pO₂/atm < 1 at 700 ≤ T/°C ≤ 900. At constant T, a p-type pO₂-dependence of σ is observed. Oxygen nonstoichiometry data are analyzed with regard to the enthalpy and entropy of oxidation ΔH_ox^θ and ΔS_ox^θ, as well as to the partial molar enthalpy and entropy of oxygen with respect to the standard state of oxygen (pO₂^θ = 1 atm), (h_O − H_O^θ) and (s_O − S_O^θ), respectively. For 2.67 ≤ (3 − δ) ≤ 2.79, (h_O − H_O^θ) decreases with increasing δ, while (s_O − S_O^θ) is constant within the limits of error. Defect chemical modelling was performed by an ideal solution model under consideration of three different valence states for B-site ions (Co or Fe). The dependence of σ on δ is modelled, using calculated defect concentrations as functions of δ. Deviations from the ideal behaviour suggest an immobilization of n-type charge carriers by oxygen vacancies.     

High temperature properties of the n = 2 Ruddlesden–Popper phases (La,Sr)3(Fe,Ni)2O7−δ

The crystal chemistry and mixed conductor properties of the n = 2 member of the Ruddlesden–Popper (R–P) phases Sr_3−xLa_xFe_2−yNi_yO_7−δ with 0 ≤ x ≤ 0.3 and 0 ≤ y ≤ 1.0 have been studied at high temperature. High-temperature X-ray diffraction and thermogravimetric measurements of the equilibrium pO₂ (10^− 5 ≤ pO₂ ≤ 1 atm) in the temperature range 400 ≤ T ≤ 1000 °C indicate that the Sr₃FeNiO_7−δ phase is able to accommodate a large oxygen non-stoichiometry (δ ∼ 1.5) without structural transformations. The electrical conductivity and oxygen permeability increase with the substitution of Ni for Fe in the range 550 ≤ T ≤ 1000 °C. The electrical transport of the Sr₃FeNiO_7−δ phase is thermally activated and the activation energy decreases with the substitution of Ni for Fe for a given oxygen content. The increase in the oxygen permeation flux with increasing Ni content is due to an increasing oxygen non-stoichiometry and a lower activation energy for permeation.     

Electronic transport in the novel SOFC anode material La1−xSrxCr0.5Mn0.5O3±δ

Electronic conductivity in the potential SOFC anode material La_1−xSr_xCr_0.5Mn_0.5O_3±δ has been investigated in the range 0.2 < x < 0.3. log(σT) vs. 1/T plots indicate conduction via thermally activated polaron hopping. At 900 °C, conductivity in air increases with Sr²⁺ via an increase in [B_B] holes (B—transition metal). X-ray absorption spectroscopy (XAS) studies indicate that compensation for A-site Sr substitution and oxygen vacancy formation is via the Mn cation only; Cr maintains a 3+ oxidation state and 6-fold oxygen coordination. Electronic transport occurs by percolation between Mn cations in a disordered B-site sub-lattice. Conductivity decreases with p(O₂), which is indicative of p-type conduction behaviour, but the relationship cannot be explained by a simple redox equilibrium involving Mn³⁺, Mn⁴⁺ and oxygen, possibly due to co-existence of Mn²⁺, Mn³⁺ and Mn⁴⁺ via disproportionation as with La_1−xSr_xMnO_3±δ.     

The effect of cation nonstoichiometry on the electrical conductivity of acceptor-doped CaZrO3

The electrical properties of acceptor-doped Ca_1−xZr_0.99M_0.01O_3−δ (M = Mg²⁺, In³⁺) systems were investigated as a function of cation nonstoichiometry (0 ≤ x ≤ 0.05). The characterization was carried out using the impedance spectroscopy between 550 °C and 1100 °C in dry air. The contributions of the grain and grain boundary conductivity to the total conductivity were obtained from the impedance data. When the Ca deficiency (x) increased, the total conductivity rapidly decreased with the corresponding increase in activation energy. Although the grain conductivity increased slightly with increasing x, the total conductivity is mostly determined by the highly resistive grain boundary. With varying x, the activation energy of total conductivity showed the percolation behavior. The percolation threshold values vary according to the doped species. It may be due to the difference in concentration of oxygen vacancies of the specimens.     

Electrical conductivity of (Ba0.3Sr0.2La0.5)(In1−xFex)O3−δ

We have synthesized the perovskite oxides of the (Ba_0.3Sr_0.2La_0.5)(In_1−xFe_x)O_3−δ system and measured the total electrical conductivity as a function of temperature and oxygen partial pressure. It was found that the single-phase composition region extended from x = 0.0 to x = 1.0, and that the Fe valence increased from 3.06 to 3.50 in that region. The electrical conductivity was semiconducting from x = 0.0 to x = 0.40 and metallic from x = 0.50 to x = 1.0. The total electrical conductivity at 800 °C also increased with the Fe content and achieved a maximum value of 140 (S/cm) at x = 1.0. From the dependence of the electrical conductivity on the oxygen partial pressure, we conclude that above x = 0.50, the majority carriers are holes. The estimated hole conductivity increased exponentially with the amount of Fe⁴⁺ cation present. The oxide ion conductivity was dependent on the oxygen vacancy content.     

Conductivity and oxygen permeability of a novel oxide Pr2Ni0.8 − x Cu0.2FexO4 and its application to partial oxidation of CH4

Iron-doped Pr₂Ni_0.8Cu_0.2O₄ was studied as a new mixed electronic and oxide-ionic conductor for use as an oxygen-permeating membrane. An X-ray diffraction analysis suggested that a single phase K₂NiF₄-type structure was obtained in the composition range from x = 0 to 0.05 in Pr₂Ni_0.8 − xCu_0.2Fe_xO₄. It is considered that the doped Fe is partially substituted at the Ni position in Pr₂NiO₄. The prepared Pr₂NiO₄-based oxide exhibited a dominant hole conduction in the P_O2 range from 1 to 10^− 21 atm. The electrical conductivity of Pr₂Ni_0.8−xCu_0.2Fe_xO₄ is as high as 10² S cm^− 1 in the temperature range of 873–1223 K and it gradually decreased with the increasing amount of Fe substituted for Ni. The oxygen permeation rate was significantly enhanced by the Fe doping and it was found that the highest oxygen permeation rate (60 μmol min^− 1 cm^− 2) from air to He was achieved for x = 0.05 in Pr₂Ni_0.8 − xCu_0.2Fe_xO₄. Since the chemical stability of the Pr₂NiO₄-based oxide is high, Pr₂Ni_0.75Cu_0.2Fe_0.05O₄ can be used as the oxygen-separating membrane for the partial oxidation of CH₄. It was observed that the oxygen permeation rate was significantly improved by changing from He to CH₄ and the observed permeation rate reached a value of 225 μmol min^− 1 cm^− 2 at 1273 K for the CH₄ partial oxidation.     

Influence of simultaneous doping of Sb and Pb on phase formation,superconducting and microstructural characteristics of HgBa2Ca2Cu3O8+δ

We report systematic studies of structural, microstructural and transport properties of (Hg_0.80Sb_0.2−xPb_x)Ba₂Ca₂Cu₃O_8+δ (where x = 0.0, 0.05, 0.1, 0.15, 0.2) compounds. Bulk polycrystalline samples have been prepared by two-step solid-state reaction route at ambient pressure. It has been observed that simultaneous substitution of Sb and Pb at Hg site in oxygen deficient HgO_δ layer of HgBa₂Ca₂Cu₃O_8+δ cuprate high-T_c superconductor leads to the formation of Hg-1223 as the dominant phase. Microstructural investigations of the as grown samples employing scanning electron microscopy reveal single crystal like large grains embodying spiral like features. Superconducting properties particularly transport current density (J_ct) have been found to be sensitive to these microstructural features. As for example (Hg_0.80Sb_0.05Pb_0.15)Ba₂Ca₂Cu₃O_8+δ compound which exhibits single crystal like large grains (∼50 μm) and appears to result through spiral growth mechanism, shows highest J_ct (∼1.85 × 10³ A/cm²) at 77 K. A possible mechanism for the generation of spiral like features and correlation between microstructural features and superconducting properties have been put forward.     

Mixed conductivity and electrocatalytic performance of SrFeO3-δ–SrAl2O4 composite membranes

Oxygen-ionic and electronic transport in dense (SrFe)_1−x(SrAl₂)_xO_z composites, consisting of strontium-deficient Sr(Fe,Al)O_3-δ and SrAl₂O₄ phases, is determined by the properties of perovskite-like solid solution. Increasing the content of SrAl₂O₄, with a total conductivity as low as 5 × 10^− 7 −  10^− 5 S × cm^− 1 at 973–1273 K in air, results in the gradual decrease of the partial conductivities, but also enables the suppression of thermal expansion. Compared to single-phase SrFe_1−xAl_xO_3-δ, (SrFe)_1−x(SrAl₂)_xO_z composites exhibit enhanced thermomechanical properties, while the oxygen permeability of these materials has similar values. The composite membranes exhibit stable performance under air/(H₂–H₂O–N₂) and air/(CH₄–He) gradients at 973–1173 K. The oxidation of dry methane by oxygen permeating through (SrFe)_0.7(SrAl₂)_0.3O_z results in dominant total oxidation, suggesting the necessity to incorporate a reforming catalyst into the ceramic reactors for natural gas conversion.     

Synthesis and structural characterization of perovskite type proton conducting BaZr1−xInxO3−δ (0.0 ≤ x ≤ 0.75)

Solid state sintering has been used to prepare the cubic perovskite structured compounds BaZr_1−xIn_xO_3−δ (0.0 ≤ x ≤ 0.75). Analysis of X-ray powder diffraction (XRPD) data reveals that the unit cell parameter, a, increases linearly with an increased Indium concentration. XRPD data was also used to demonstrate the completion of sample hydration, which was reached when the materials showed a set of single-phase Bragg-peaks. Dynamic thermogravimetric analysis (TGA) data showed that approx. 89% of the total number of available oxygen vacancies can be filled in BaZr_1−xIn_xO_3−δ for x = 0.50, and that the maximum water uptake occurs below 300 °C. Rietveld analysis of the room temperature neutron powder diffraction (NPD) data confirmed the average cubic symmetry (space group Pm-3m), and an expansion of the unit cell parameter after the hydration reaction. The strong O–H stretch band, 2500–3500 cm^− 1, in the infrared absorbance spectrum clearly manifests the presence of protons in the hydrated material. Proton conductivity of hydrated BaZr_1−xIn_xO_3−δ, x = 0.75 was investigated during heating and cooling cycles under dry argon atmosphere. The total conductivity during the heating cycle was nearly two orders of magnitude greater than that of cooling cycle at 300 °C, whilst these values were similar at higher temperatures i.e. T > 600 °C.     

Electric property of mixed conductor BaIn1−xCoxO3−δ

We synthesized BaIn_1−xCo_xO_3−δ (x = 0–0.8) with a defective perovskite structure by partly replacing In with Co in Ba₂In₂O₅. Based on XRD measurements, the synthesized compound was found to have cubic perovskite and orthorhombic brownmillerite structures depending on the amount of Co. BaIn_1−xCo_xO_3−δ (x = 0.2 and 0.3) showed high total electrical conductivities without undergoing the structural transformation that the original Ba₂In₂O₅ undergoes. Some of the samples showed both electronic and oxide ionic conductivities. At the same time, the oxide ionic conductivity was comparable with that of Ba₂In₂O₅. For example, the sample with x = 0.1 had a total electrical conductivity of 4.7 × 10^− 1 S cm^− 1 and an oxide ion transport number of 0.52 at 850 °C.     

Synthesis and characterisation of Cr3+-containing NASICON-related phases

Chromium-containing NASICON-related phosphates of the type Na_(1+x)Cr_xM_(2−x)P₃O₁₂) (M = Ti, Hf, Zr) have been synthesised by solid state reaction and structurally characterised by Rietveld refinement of the powder X-ray diffraction data. Materials of composition A_(1+x)/2Cr_xZr_(2−x)P₃O₁₂ (A = Cd, Ca, Sr), have also been prepared and characterised. The crystal structure of Na_(1+x)Cr_xM_(2−x)P₃O₁₂ corresponds to R-3c symmetry for x values ranging from 0.15 to 2.00, whereas compounds of composition A_(1+x)/2Cr_xZr_(2−x)P₃O₁₂ corresponding to R-3c are obtained when x ≤ 1.00 for Sr²⁺ and Ca²⁺, and x ≤ 1.50 for Cd²⁺. The polarizing effect of the two different metal ions A and M on the phosphorus atom and the P–O bond was studied by both ³¹P MAS NMR and infrared spectroscopy and shows that the electron density on the phosphorus, and thus the strength of the P–O bonds, are affected by both the interstitial (A) and the structural (M) metal ions.     

Preparation,characterization and electrical property of Mn-doped ceria-based oxides

Manganese-doped ceria-based oxides, Ce_1−xMn_xO_2−δ (0.05 ≤ x ≤ 0.3) and Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x≤ 0.2, 0.05 ≤ y ≤ 0.25) were synthesized, and crystal phase analysis by XRD and measurements of electrical properties were performed. Solubility limit of Mn in Ce_1−xMn_xO_2−δ˙ seemed to be between 5 mol% and 10 mol% and Mn₃O₄ was the main by-product above the solubility limit in the case of heat treatment at 1300 °C. Judging from the oxygen partial pressure dependence of total conductivity and emf measurements, Ce_1−xMn_xO_2−δ˙ is a single-phase mixed conductor within the composition below the solubility limit, and when the composition of Mn exceeds the solubility limit, it becomes the dual-phase mixed conductor of Ce_1−xMn_xO_2−δ˙ and Mn₃O₄. The doing of Mn in gadlia-doped ceria, Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x ≤ 0.2, 0.05 ≤ y ≤ 0.25), was more difficult than that in CeO₂ presumably due to the preferential reaction between Gd and Mn to give GdMnO₃ to the GDC solid solution formation, and the Mn doping seems not to be so effective in preparing the mixed ionic–electronic conductor based on GDC.     

Defect interactions in La0.3Sr0.7Fe(M′)O3−δ (M′ = Al,Ga) perovskites: Atomistic simulations and analysis of p(O2)-T-δ diagrams

Atomistic modelling showed that a key factor affecting the p(O₂) dependencies of point defect chemical potentials in perovskite-type La_0.3Sr_0.7Fe_1−xM′_xO_3−δ (M′ = Ga, Al; x = 0–0.4) under oxidizing conditions, relates to the coulombic repulsion between oxygen vacancies and/or electron holes. The configurations of A- and B-site cations with stable oxidation states have no essential influence on energetics of the mobile charge carriers, whereas the electrons formed due to iron disproportionation are expected to form defect pair clusters with oxygen vacancies. These results were used to develop thermodynamic models, adequately describing the p(O₂)-T-δ diagrams of La_0.3Sr_0.7Fe(M′)O_3−δ determined by the coulometric titration technique at 923–1223 K in the oxygen partial pressure range from 1 × 10^− 5 to 0.5 atm. The thermodynamic functions governing the oxygen intercalation process were found independent of the defect concentration. Doping with aluminum and gallium leads to increasing oxygen deficiency and induces substantial changes in the behavior of iron cations, increasing the tendencies to disproportionation and hole localization. Despite similar oxygen nonstoichiometry in the Al- and Ga-substituted ferrites at a given dopant content, the latter tendency is more pronounced in the case of aluminum-containing perovskites.     

Ionic and electronic conductivity of Yb2+xTi2−xO7−x/2 materials

Bulk and grain boundary conductivities of Yb_2+xTi_2−xO_7−x/2 (x = 0, 0.1, 0.18 and 0.29) materials were studied by impedance spectroscopy in the range 300–900 °C in air. Ionic and electronic conductivities were separated by both ion blocking Hebb–Wagner measurements and total conductivity measurements as a function of oxygen partial pressure in the temperature range 700–1000 °C. The oxygen partial pressure dependence of the total conductivity shows that these materials are nearly pure ionic conductors in air and that the ionic conductivity decreases for Yb-rich compositions. This was interpreted as a predominant effect of a decrease in mobility of ionic charge carriers, opposing the expected increase in concentration of oxygen vacancies with increasing Yb content. The studied materials become mixed conductors under typical fuel conditions, except possibly at temperatures below about 700 °C. Yb-excess slightly suppresses the electronic conductivity.