光学材料 光电功能材料

O472.3 2004053905 固相热分解法合成非晶ZnO及其表征=Synthesis and characteristics of amorphous zinc oxide by solid-state pyrolytic reaction[刊,中]/王志军(中科院长春光机所激发态物理重点实验室,吉林,长春(130033)),王之建…∥发光学报。—2003,24(5)。—497-500     

高温固相法制备ZnO∶Zn绿色荧光粉及其在近紫外LEDs中的应用研究

采用高温固相法在温度900～1 100 ℃,时间3 h的条件下制备出系列ZnO∶Zn荧光粉样品,并进行了封装应用研究。利用X射线衍射分析(XRD)、场发射扫描电子显微镜(FESEM)、荧光分光光度计(PL)和可见光光谱分析系统等手段对样品分别进行了表征分析。研究结果表明：所制备的荧光粉样品均具有ZnO晶型的六方纤锌矿结构,样品可以有效地被近紫外光激发,所发射的绿光光谱具有宽谱发射特征,峰位于502 nm归属于氧空位发射,同时940 ℃条件下制备的荧光粉样品具有最高的发光强度。结合近紫外LED芯片和RGB荧光粉分别制备出绿光LED和白光LED,其中绿光LED在不同驱动电流(250～500 mA)泵浦下表现出稳定的光谱发射特性,发射光谱谱型和色坐标基本未变,发射强度随电流升高而增加,所制备的白光LED在色温3 212 K时,显色指数达到94.1,发光效率为85.6 lm·W-1(@300 mA,9.3 V),在(250～500 mA)驱动电流泵浦下同时也表现出稳定的光谱发射特性,所制备的ZnO∶Zn绿色荧光粉对于制备高显色、高品质近紫外白光LED具有潜在的应用价值。     

弯曲表面上ZnO亚微米棒阵列的制备

以ZnS和金属Zn粉末混合物为蒸发源以及金属Zn片为衬底,利用热蒸发气相沉积方法,在弯曲的金属Zn微球表面上,成功地获得了ZnO亚微米棒阵列结构。场发射扫描电镜研究表明:在弯曲的Zn微球表面,能自组织地生长出大量的截面为六边形的ZnO亚微米棒,这些亚微米棒的平均直径为500nm,长约1μm。棒的顶部是平滑的。能量散射X射线谱结果表明:合成的产品只存在Zn和O两种元素,其成分比例接近1∶1。没有观察到S元素。光致发射(PL)光谱显示:在387nm紫外波长处,出现一个强的半峰全宽为16nm的窄发光峰,可归属于ZnO的近带边发光,而509nm左右较弱的宽峰则源于界面缺陷态发光。这些研究结果说明我们所合成的这种ZnO亚微米棒阵列材料在紫外受激发射器件方面有着潜在的应用价值。     

退火处理对ZnO纳米线紫外探测器性能的改善

通过介电泳方法定向排列了ZnO纳米线,制作了自组装有序的纳米线紫外探测器.为了适合在金叉指电极上排列,用水热方法设计生长了超长的ZnO纳米线,并通过700℃的热退火处理,使得可利用的表面缺陷增多.通过研究器件的光致发光光谱和光响应,发现光、暗电流比和响应恢复时间有显著提高,并分析了其中可能的机理.     

聚氧化乙烯表面修饰对ZnO光学性质的影响

利用聚氧化乙烯(PEO)对ZnO表面进行修饰,研究有机包覆对ZnO光学性质的影响。用吸收光谱和光致发光光谱来表征和研究PEO包覆对ZnO纳米粒子光学性质的影响。吸收光谱结果表明随着ZnO薄膜中PEO含量的增加,激子吸收峰逐渐向低能侧方向移动。光致发光光谱是由紫外发射和与氧空位有关的深能级缺陷发光组成,且随着ZnO薄膜中PEO含量的增加,紫外发射与深能级发光强度之比逐渐增大,当ZnO薄膜中的PEO达到最大值时,其比值为31．5,远远大于纯ZnO薄膜的紫外发射与深能级发光强度之比1．04。由此可见,ZnO被PEO包覆后,提高了紫外发光效率,改善了ZnO薄膜的质量。     

四角锥氧化锌的制备及其强蓝光发射性质研究

采用热蒸发锌(Zn)粉的方法制备了大量的ZnO纳米棒状和四角锥状结构。用扫描电子显微镜(SEM)、拉曼光谱(Raman Spectra)和光致发光谱(PL)对样品进行了形貌,结构和发光特性分析。结果表明:合成的ZnO纳米棒具有良好的晶体结构,直径约100～500 nm,长度约2～5μm,还有一些四角锥状结构。在325 nm波长光激发下,有微弱的391 nm带边紫外发射和很强的488 nm蓝光发射,呈现出纳米ZnO优异的蓝光特性,并对其生长机理和发光机理进行了初步的探讨。     

BaZr(BO3)2:Eu的合成及发光性能研究

用硝酸盐热分解法成功制备了BaZr(BO3)2:Eu(Eu3+的掺杂量为摩尔分数5%)荧光材料,并研究了其在254及147 nm光束激发下的发光特性.254 nm光束激发下的发射主峰位于612 nm处,归属于Eu3+的5D0-7F2的电偶极跃迁,但在147 nm光束激发下的发射主峰位于592 nm处,归属于Eu3+的5D0-7F1的磁偶极跃迁.通过激发光谱分析,上述现象归因于在紫外激发下占据非对称格位Ba2+的Eu3+被优先激发,而在真空紫外激发下占据对称格位Zr4+的Eu3+被优先激发.结果表明BaZr(BO3)2:Eu并不适合作为等离子平板显示器用红色发光材料.     

中位-四l-(对十六酰氧基)苯基卟啉的合成与表征

本文以四－（对羟基苯基）卟啉与十六酰氯为原料,通过酯化反应合成了中位－四－（对十六酰氧基苯基）卟啉,采用红外光谱监测了反应进程,以硅胶为固定相,氯仿为洗脱剂采用柱层析方法对反应产物进行了分离与提纯。最后用元素分析,紫外可见光谱,红外光声光谱,核磁共振氢谱,摩尔电导等手段对合成产物进行了结构表征,对主要的紫外光谱,红外光谱及核磁共振氢谱吸收带进行了经验归属,初步确定了合成产物的结构。     

ZnO薄膜的特殊光谱性质及其机理

以同步辐射真空紫外光(195nm)为激发源,在低温下观察到Si基衬底上ZnO薄膜的发光有三种紫外发射,其峰值波长分别为380,369．5,290nm。它们各自具有不同的衰减时间和不同的温度依赖关系,但其激发谱相同。强激发带不在近紫外区,而在真空紫外区(100～200nm),可能源于ZnO的下价带(Zn3d组态)电子的激发。对三种紫外发射的来源作了分析讨论。     

Co掺杂ZnO纳米棒的共振拉曼光谱和发光特性

采用X射线衍射(XRD)和透射电子显微镜(TEM)手段对微乳液法合成的Zn0.9Co0.1O纳米棒进行了表征.通过室温下的共振拉曼光谱和光致发光光谱手段,研究了所合成纳米材料的共振拉曼光谱和发光特性,并与体相ZnO的研究结果对比,发现合成的材料具有四阶声子紫外共振拉曼散射,而体相材料只有两阶,并观察到在紫外和可见区域所...     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.