多层膜外退火方法制备MgB2超导薄膜

报道了利用电子束蒸发的Mg/B多层膜作为前驱体，然后退火制备MgB₂薄膜的工作. 实验中发现，采用翻转膜面的退火处理方式可以有效地避免降温过程中Mg蒸气在薄膜表面形成的颗粒凝结，由此稳定地实现了面积为10 mm×10 mm，均匀、平整的超导薄膜的制备，T_c达35 K，转变宽度为0.8 K，在5 μm×5 μm的区域内薄膜的平均粗糙度小于10 nm. 为了便于后续器件制作过程中的微加工工艺，研究了膜厚小于1000 ?时薄膜的成相规律，发现当样品厚度减薄后，T_c会有明显降低. 通过调整前驱薄膜中的不同分层厚度，仍可实现转变温度达30 K以上、厚度约600 ?的MgB₂薄膜，在20 K时的临界电流密度为2.4×10⁶ A/cm².     

光折变法制备的As2S8条形波导的光阻断效应

实验研究了As₂S₈薄膜光折变现象.提出并采用紫外光激励的方法试制了As₂S₈条形波导，导模激励显示该波导具有良好的导波特性.在此基础上，考察了As₂S₈条波导的光阻断效应，实现了光-光效应的开关功能. 关键词： 光波导技术 2S₈条形波导')" href="#">As₂S₈条形波导 光阻断效应 光激励法     

Optical waveguides in LiNbO3 formed by ion implantation

Abstract

Ion implantation in LiNbO₃ can be used to modify the refractive index. The change in indices, n ₀ n _e results from the damage formed by energy deposited by the (dE/dx)_nuclear collisions between the ions and the lattice and is independent of the ion species. A saturation change in index of some ?7% occurs after a deposition of 10²³ keV cm^?3 at 300K, greater changes of ?9 % occur with implants at 77K. Annealing studies indicate the optical absorption formed during irradiation is removed below 200°C whereas the index changes exist up to 400°C. For optical waveguide production a negative change in the index is not ideal as the damaged layer cannot directly act as the region of optical confinement. However the (dE/dx)_electronic term is unimportant and so we have been able to form optical waveguides by ion implantation with light energetic ions (e.g. MeV He⁺ ions) because the damaged layer is then formed beneath an unchanged high index surface layer. This retains the desirable electrooptic properties of the single crystal LiNbO₃. The experimentally observed waveguide modes are in accord with our theoretical predictions of the refractive index profiles.     

钛离子辐照对MgB2超导薄膜的载流能力和磁通钉扎能力的影响

利用混合物理化学气相沉积法(hybrid physical-chemical vapor deposition, HPCVD)可以制备出高性能的MgB₂超导薄膜, 再对薄膜进行钛(Ti)离子辐照处理.经过辐照处理后的样品被掺入了Ti元素, 与未处理的干净MgB₂样品相比,其超导转变温度没有出现大幅度的下降, 而在外加磁场下的临界电流密度得到了明显的提高,同时样品的上临界磁场也得到了提高. 在温度5 K, 外加垂直磁场为4 T的情况下, Ti离子辐照剂量为1× 10¹³/cm²的样品的临界电流密度达到了1.72× 10⁵ A/cm², 比干净的MgB₂要高出许多,而其超导转变温度仍能维持在39.9 K的较高水平.     

Optical properties of a waveguide written inside a LiTaO3 crystal by irradiation with focused femtosecond laser pulses

Optical waveguides were fabricated by modifying the optical properties inside a LiTaO₃ crystal by irradiation with femtosecond laser pulses, and the performance and optical properties of the waveguide were investigated. On the basis of near-field pattern of the light guided through the waveguides, the optimum writing conditions such as the pulse energy and the pulse duration were determined. The waveguide written inside a LiTaO₃ crystal had a strong polarization dependence of guided light. Observation by a polarized microscope suggested that the stress distribution around the photoexcited region should be responsible for the polarization dependence of guided light. In addition, the second harmonic generation from a laser beam passing through the waveguide was observed, which suggests that the ferroelectric properties of LiTaO₃ were preserved after the photoexcitation.     

近场光学显微镜研究CdS0.65Se0.35纳米带空间分辨光致荧光谱

通过热蒸发方法成功制备出CdS_0.65Se_0.35纳米带，得到的纳米带表面光滑，宽度厚度均一，表现出很高的结晶质量.使用近场光学显微镜对纳米带室温下的带边荧光波导和光致荧光近场光谱进行研究.发现CdS_0.65Se_0.35纳米带呈现良好的光波导的特性；同时通过近场光学显微镜得到的空间分辨光谱，发现随着传播距离的增大，纳米带的光致荧光光谱有持续的红移现象.这种光谱红移现象是带间跃迁过程中带尾态的吸收效应引起的，并作了光谱带尾态吸收的理论模拟与实验结果进行比较.光波导传输过程中光谱的变化反映了信息在整个传导过程中的情况，体现了信息传递过程中的稳定性和有效性.三元合金材料CdS_0.65Se_0.35纳米带的波导和光谱性质研究，对于其他组分可调的三元合金纳米结构的制备和研究，及发展新型的纳米功能器件有重要意义.     

Optical fiber tip in front of a phase conjugator: focused light spot with inclusion of evanescent field contribution

 Within the framework of electric dipole approximation, the focused light spot produced by a tiny optical fiber tip in front of a phase conjugate mirror is investigated numerically. The fiber tip is the probe of a reflection scanning near field optical microscope and the incident light is guided through the fiber. Intensity distribution of local field is calculated in the half space where the fiber tip locates. Both homogeneous (q _‖≤ω/c ₀) and part of inhomogeneous (ω/c ₀<q _‖≤ωn/c ₀) fields are included in establishing a field propagator (Green’s function) which is employed to calculate the local field distribution. The local field forms at the tip position a diffraction light spot with a finite central value and a finite size, and when the tip-surface distance is sufficient small, the strength and the shape of the light spot become a function of the distance, which is due to the contribution of evanescent field. Fairly good agreements are found with the existing experimental reports. Received: 30 April 1996/Accepted: 19 August 1996     

Laser-induced voltage effects in Ca3Co4O9 thin films on tilted LaAlO3（001） substrates grown by chemical solution deposition

Laser-induced voltage effects in c-axis oriented Ca3Co4O9 thin films have been studied with samples fabricated on 10 tilted LaAlO3(001) substrates by a simple chemical solution deposition method. An open-circuit voltage with a rise time of about 10 ns and full width at half maximum of about 28 ns is detected when the film surface is irradiated by a 308-nm laser pulse with a duration of 25 ns. Besides, open-circuit voltage signals are also observed when the film surface is irradiated separately by the laser pulses of 532 nm and 1064 nm. The results indicate that Ca3Co4O9 thin films have a great potential application in the wide range photodetctor from the ultraviolet to near infrared regions.     

Synthesis of photosensitive poly(methyl methacrylate-co-glycidyl methacrylate) for optical waveguide devices

Photosensitive poly(MMA-co-GMA) for optical waveguide was synthesized, and the refractive index of the polymer film was tuned in the range of 1.481–1.588 at 1550 nm by mixing with bis-phenol-A epoxy resin. The film, which was made by spinning coated the poly(MMA-co-GMA) with photo initiator, had good UV light lithograph sensitivity, high glass transition temperature (T _g : 153°C, after crosslinking) and good thermal stabilities (T _d : up to 324°C, after crosslinking). The optical waveguides with very smooth top surface were fabricated from the resulting polymer by direct UV exposure and chemical development. For waveguides with cladding, the propagation losses of the channel waveguides were measured to be below 3 dB/cm at 1550 nm.     

蓝宝石基片上制备大面积Tl2Ba2CaCu2O8超导薄膜

在2英寸双面蓝宝石基片上采用CeO₂作为缓冲层制备了高质量Tl₂Ba₂CaCu₂O₈(Tl-2212)超导薄膜.以金属铈作为溅射靶材,采用射频磁控反应溅射法生长了c轴织构的CeO₂缓冲薄膜,并研究了不同生长条件对于CeO₂缓冲层的晶体结构及表面形貌的影响.超导薄膜采用直流磁控溅射和后热处理的方法制备.扫描电子显微镜(SEM)图像显示,超     

Optical second-harmonic generation in a thin-film waveguide without control of film thickness

An optical second-harmonic wave can be generated in a three-layered optical waveguide of arbitrary film thickness under phase-matching condition. Phase-matching is achieved by utilizing mode dispersion in an optical waveguide with a two-dimensional configuration. A numerical analysis of the matching condition is given and the results of the observation of the optical second-harmonic wave of a guided Nd : YAG laser in a Ti-indiffused LiNbO₃ nonlinear film are described.     

Waveguide properties and optical switching of prism-coupled Au:SiO2 nanocomposite films

In this study, we present theoretical and experimental analyses on the waveguide mode properties of prism-coupled Au:SiO₂ nanocomposite films with the near infrared laser of 1550 nm wavelength where the optical absorption diminished enough for the generation of guided mode. The evolution of guided mode in the nanocomposite waveguide and its propagation properties were also evaluated. As an effective way of utilizing the surface plasmon resonance properties for the application to optical switching devices, we employed an attenuated total internal reflection type optical switch geometry and tested its effectiveness for the absorptive opto-functional materials system using a cross-modulation technique with 532-nm pump and 1550-nm probe beams. The index change probe beam experiences was found to be purely refractive in nature and negative in sign, presumably due to the photo-thermal effect induced in the nanocomposite film by the irradiation of pump beam.     

Acousto-optic light deflection in an Al2O3 optical waveguide structure

The total deflection of an optical guided wave by a surface acoustic wave (SAW) in a silicon-based SiO₂/AL₂O₃/SiO₂ optical waveguide structure is reported. The SAW is generated by an interdigital transducer with piezoelectric ZnO deposited on top of the optical waveguide structure.     

二氧化钛修饰的微结构聚合物光纤预制棒制备及其在光催化中应用的探索研究

首次用二氧化钛(TiO₂)纳米材料修饰的547孔微结构聚合物光纤(MPOF)二次预制棒作为阵列化微管式光催化反应器对亚甲基兰的光催化分解进行研究.将高光催化活性的P25型二氧化钛纳米粒子均匀分散在TiO₂溶胶中,对547孔微结构聚合物光纤孔洞内壁进行铺膜,得到了负载光催化剂的阵列化微管材料.该TiO₂MPOF有序复合的阵列化微管不仅对二氧化钛纳米粒子起到负载作用,还可以作为光波导介质(rolling-up薄膜波导,聚光、导光进入二氧化钛薄膜层)、污染物反应流体通道.以有机染料亚甲基兰为模拟污染物,研究了TiO₂负载量、亚甲基兰的初始浓度及溶液pH值等因素对光降解效果的影响.该反应器547个孔道的内表面用于负载光催化剂,不仅增加了固-液接触面积,也提高了光的吸收效率,从而提高了光催化效率.迄今为止,这种兼具导光、聚光、传质、负载功能于一体的光催化反应器还未见报道.     

Secondary-ion-mass spectrometry study on near-stoichiometric LiNbO3 strip waveguide fabricated by vapour transport equilibration and Ti co-diffusion

Secondary-ion-mass spectrometry was applied to study Ti-concentration profiles in the depth direction and on the surface of near-stoichiometric (NS) Ti:LiNbO₃ strip waveguides fabricated using vapour transport equilibration (VTE) and co-diffusion of Ti-metal strips. Results show that the profile of Ti concentration along the width direction on the waveguide surface can be well fitted by a sum of two error functions, while, in the depth direction, the Ti concentration follows either a complementary error function or a generalized Gaussian function. Surface Ti concentration, 1/e width and depth, mean diffusivities along the width and depth directions of the guide are, respectively, 1.04?×?10²¹?cm^–3, 8.5?µm, 6.3?µm, 0.18 and 0.1?µm²/h. Two-dimensional refractive index profile in the NS waveguides is indirectly constructed by assuming linearity between Ti-induced index change and Ti concentration. The surface refractive index increments at 1545?nm, Δn_o and Δn_e , are evaluated to be 3.132?×?10^–3 and 1.186?×?10^–2, respectively. All of the above-mentioned diffusion and optical parameters are compared with the corresponding data of the common congruent Ti:LiNbO₃ waveguide or NS waveguide fabricated starting from a NS substrate. The rationality of the assumed linear relationship between the index change and the Ti concentration is discussed. The results show that the assumed linearity remains controversial, and all expressions and data with regard to the refractive index are the approximate results and need to be verified by direct measurement on refractive index.     

Te/TeO2-SiO2复合薄膜的吸收和非线性光学特性研究

应用分光光度计测量Te/TeO₂-SiO₂复合薄膜的透射光谱和吸收光谱, 在480nm附近观察到Te颗粒引起的等离子体共振吸收峰; 采用Z扫描技术研究了共振(激发波长为532 nm)和非共振情况下(激发波长1064 nm) 不同电位制备薄膜的Te颗粒状态与复合薄膜的三阶非线性极化率的关系. 基于有效介质理论对复合薄膜的三阶非线性效应进行分析, 研究Te颗粒大小对Te/TeO₂-SiO₂复合薄膜的非线性光学性质的影响及其产生机理. 结果表明薄膜制备过电位增大, Te的粒径减小, 颗粒数量多, 颗粒分布趋于均匀, 使得金属颗粒的表面等离子体共振峰红移, 吸收强度增强, 导致三阶非线性光学效应增强, χ⁽³⁾由1064 nm的5.12×10^-7 esu增大为532 nm的8.11×10^-7 esu. 关键词： 碲 二氧化碲 复合薄膜 三阶非线性     

Large nonlinear optical properties of Fe2O3 nanoparticles

Nonlinear optical properties of Fe₂O₃ nanoparticles were investigated by the signal-beam Z-scan technique with Ar⁺ and Ne–He lasers. The largest reported effective nonlinear coefficient, n₂=−8.07×10⁻⁷ cm²/W, was obtained. It is demonstrated that the nonlinear optical response originals from quantum confinement effect.     

Planar waveguides in calcium barium niobate fabricated by MeV He ion implantation

A planar optical waveguide was formed in calcium barium niobate (CBN) crystal by 2.8-MeV He-ion implantation with a dose of 1.0×10¹⁶ ions/cm² at room temperature. The prism-coupling method was used to take dark mode measurements at both 633 nm and 1539 nm. The refractive-index profile (n_o and n_e) of the He-implanted CBN waveguide was analyzed with the reflectivity calculation method. The results show that the MeV He implantation results in a decrease in refractive index in barriers for both n_o (4.1%) and n_e (3.1%), but for n_e there is an increase in the waveguide region. The intensity profile of the guide mode and waveguide loss were obtained by end-fire coupling. PACS 42.79.Gn; 61.80.Jh     

Synthesis of a fluorinated photoresist for optical waveguide devices

A linear fluorinated bis-phenol-A novolac resin (LFAR) for optical waveguide was synthesized based on 4,4′-(hexafluoro-isopropylidene)diphenol, epoxy chloropropane and formaldehyde. Negative fluorinated photoresist (FP) was made by composing the LFAR, diphenyl iodonium salt and solvent. The film, which was made by spin-coating FP, had good UV light lithograph sensitivity, large hardness and high glass transition temperature (T _g >170°C, after crosslinking). Low-loss optical waveguides with very smooth top surface were fabricated from the resulting FP by direct UV exposure and chemical development. For waveguides without upper cladding, the propagation loss of the channel waveguides was measured to be 0.21 dB/cm at 1550 nm.     

The nonlinear optical property and photoinduced anisotropy of?a?novel azobenzene-containing fluorinated polyimide

A novel azobenzene-containing fluorinated polyimide was synthesized. The nonlinear optical property and photoinduced birefringence of a polyimide thin film were investigated. Large third-order nonlinear refraction (n ₂=−4.49×10⁻¹¹ cm²/W) was observed in the polyimide thin film by carrying out Z-scan measurement. The polyimide thin film exhibited larger nonlinear refraction than that of a mono-azo dye doped PMMA thin film (n ₂=−1.63×10⁻¹² cm²/W). The photoinduced birefringence of the polyimide thin film (▵ n∼10⁻²) under different pump intensities was investigated; it was much larger than that of the mono-azo dye doped PMMA thin film (▵ n∼10⁻³). Moreover, the time constants for birefringence growth and relaxation processes were determined.