Mode-locked all-fiber ring laser based on broad bandwidth in-fiber acousto-optic modulator

Active mode-locking of long-cavity all-fiber ring laser based on broad bandwidth in-fiber acousto-optic modulator (AOM) is reported. The proposed AOM combines the advantages of intermodal coupling induced by standing flexural acoustic waves in a double-ended tapered fiber. We focus our attention on the effects of large tapered transitions to improve the bandwidth modulation. Our approach permits the implementation of broad modulation bandwidth (13 nm), high modulation depth (50 %), and low optical loss (1.1 dB) in an 80-μm configuration. The effects of the AOM in the laser performance are also investigated. Transform-limit optical pulses of 25 ps temporal width and 2.7 W peak power were obtained at 2.46 MHz repetition rate.     

A Low-Cost 16 Quadrature Amplitude Modulation Direct-Detection–Orthogonal Frequency-Division Multiplexing Radio-over-Fiber System Using Low-Cost Direct-Modulation Laser to Generate Optical mm-Wave

Abstract

This article demonstrates a novel scheme to generate 16 quadrature amplitude modulation orthogonal frequency-division multiplexing signals for radio-over-fiber systems using a low-cost direct-modulation laser to generate an optical millimeter-wave. Mathematical analysis of that system is also investigated. The fiber Bragg grating is employed because the repetitive frequency of the radio frequency source and the bandwidth of the optical modulator are largely reduced, and the architecture of the radio-over-fiber system is simpler. Because no expensive broadband external modulator is used, the overall system is considered a low-cost solution. The simple structure and low cost of the radio-over-fiber system is attractive for the future cost-effective systems.     

用于激光聚变驱动器的全光纤、全固化光脉冲产生系统

报道一种全固化、全光纤的用于高功率激光驱动的惯性约束聚变驱动器的光脉冲产生系统,采用单纵模振荡器输出连续激光信号,经过相位调制器和振幅调制器,得到一个时间波形上已整形且具有一定带宽(约0.1 nm)的激光脉冲,经光纤放大器放大并经光纤分束器分束后同时输出四路激光脉冲,各路激光脉冲先通过时间同步调整单元精确控制时间同步关系后,经可编程光纤衰减器调节各路之间的功率平衡后再通过光纤放大器做进一步放大并通过150 m光纤传输输出至预放系统.该光纤系统可输出0.3—20 ns、带宽0.1 nm、能量数纳焦的几乎任意 关键词： 激光聚变驱动器 前端 光纤激光系统     

全光纤多种子激光脉冲产生系统

报道一种可精确同步输出宽带啁啾脉冲、纳秒级整形脉冲以及窄带光参量啁啾放大抽运脉冲的全光纤多种子激光脉冲产生系统.采用掺镱光纤锁模激光器和掺镱单纵模光纤振荡器作为系统的光源,将掺镱光纤锁模激光器输出的超短脉冲分束啁啾展宽至0.9ns后,一路进行放大产生10μJ量级的宽带啁啾脉冲为高能拍瓦激光器系统提供种子光脉冲,另一路通过1.2nm滤波产生140ps的基元脉冲,通过光纤堆积器产生可编程整形的2.3ns脉冲,再经过放大达到10μJ量级,提供任意整形的压缩脉冲.同时,将部分掺镱光纤锁模激光器输出的超短脉冲进行光电转换并锁相后,产生与锁模超短脉冲高精度同步的电脉冲用于触发幅度调制器,将掺镱单纵模光纤振荡器输出的连续光削波放大,产生光参量啁啾放大抽运脉冲.该系统能够根据物理实验的需要,非常灵活地在输出各种脉冲之间做出选择.     

Simulative investigation on the impact of laser-spectral width in single-tone radio-over-fiber transmission system using optical single side-band technique

In this paper, we analyzed the impact of laser-spectral width incorporating dual-electrode Mach–Zehnder modulator (DEMZM) in single-tone radio-over-fiber (RoF) transmission system by simulation setup. It is shown that an improvement in the measurement of received radio frequency (RF) power is achieved by reducing the laser line width from 100 MHz to 100 kHz, which further improves the BER rate and optical link by transmitting the information with low power. The results are calculated for 20 and 50 km optical single sideband (OSSB)–RoF transmission system by varying the chirp from 0 to −3 as it requires less bandwidth than optical dual sideband (ODSB)–RoF system and is tolerable for power degradation due to a chromatic fiber-dispersion, through a standard single-mode fiber (SSMF) carried by a continuous wave (CW) laser at 1550 nm of laser-spectral width varying from 100 MHz to 100 kHz with CW power of 10 mW that modulates a single RF channel of 20 GHz. Further, deployment of such lasers with OSSB scheme helps the telecom industry to reduce the designing cost of RoF communication systems.     

Generation of flat optical frequency comb by fiber loop modulation

We propose a novel flat optical frequency comb generation system that employs fiber loop modulation and experimentally demonstrate its operation. Generally, when an external laser beam is injected into a fiber loop system including an optical modulator and an amplifying medium, multiple sidebands are generated exponentially. On the other hand, the fiber loop starts mode-locked oscillation at a center frequency to maximize the round-trip gain in the fiber loop from the seeds of the injected laser sidebands. By locking the sidebands from fiber loop modulation with the mode-locked oscillation in the fiber loop, the synchronous spectrum between the mode-locked oscillation and the sidebands can be shaped into a flat spectrum. Thus, a flat optical frequency comb with a flatness of about ±1 dB is obtained in the spectral bandwidth of about 1 THz.     

Ultrashort pulse generation using fiber FM laser

Ultrashort optical pulse generation using a fiber FM laser is presented and analyzed in detail. Fiber FM laser operation is realized using a fiber ring with an internal phase modulator and an erbium-doped fiber amplifier. To compress FM laser pulses, an external dispersive single-mode fiber is employed. Furthermore, by external intensity modulation, the pulse background is removed. The background ratio of the generated ultrashort pulse is calculated and compared with the experimental results. The experimental results show an output optical pulse width of 1.77 ps and a spectral bandwidth of 0.5 THz.     

交叉相位调制提高半导体激光器混沌载波发射机带宽方法

提出半导体激光器混沌交叉相位调制(XPM)光反馈提高混沌载波发射机带宽方法,建立了有外腔光纤传输反馈XPM控制下的激光动力学物理模型.理论导出XPM作用下激光双反馈频率失谐公式,指出XPM产生的非线性相移影响了激光器增益和线宽增强因子,其光纤二阶非线性效应使激光振幅和相位变化更加丰富,而非线性相移的出现进一步增加了新的频率分量并使频谱展宽.数值结果表明,XPM使激光器混沌带宽增加到4倍以上,使激光混沌张弛振荡频率增加到2.85倍,其光纤长度、入纤光功率、面镜反射系数、光纤二阶非线性系数等都能影响激光混沌带宽.     

Robust laser frequency stabilization by serrodyne modulation

We report the relative frequency stabilization of a distributed feedback erbium-doped fiber laser on an optical cavity by serrodyne frequency shifting. A correction bandwidth of 2.3 MHz and a dynamic range of 220 MHz are achieved, which leads to a strong robustness against large disturbances up to high frequencies. We demonstrate that serrodyne frequency shifting reaches a higher correction bandwidth and lower relative frequency noise level compared to a standard acousto-optical modulator based scheme. Our results allow us to consider promising applications in the absolute frequency stabilization of lasers on optical cavities.     

64 GHz optical millimeter-wave generation by octupling 8 GHz local oscillator via a nested LiNbO3 modulator

A novel scheme to generate a 64 GHz optical millimeter (mm)-wave via a nested LiNbO₃ Mach-Zehnder modulator with an 8 GHz local oscillator is proposed and simulated. Since the frequency response of the modulator and the local oscillator frequency are greatly reduced, the bandwidth requirements of the optical and electrical components in the transmitter are significantly decreased. The simulation results show that the generated optical mm-wave signal maintains good performance even after being transmitted over 20 km standard single-mode fiber.     

Design of an ultra-broadband all-optical fractional differentiator with a long-period fiber grating

We propose an all-optical in-fiber ultra-broadband fractional differentiator. We numerically demonstrate that a long-period grating inherently performs the temporal fractional differentiation on an optical pulse propagating in the fundamental fiber mode, within a certain spectral bandwidth around the resonance frequency. The device shows a good accuracy calculating the fractional time derivatives of the complex field of THz-bandwidth optical pulses.     

Mode-locked fiber laser frequency-controlled with an intracavity electro-optic modulator

We demonstrate a mode-locked, erbium-doped fiber laser with its repetition frequency synchronized to a second fiber laser via an intracavity electro-optic modulator (EOM). With servo control from the EOM (bandwidth approximately 230 kHz) and a slower speed intracavity piezoelectric transducer (resonance at approximately 20 kHz), we demonstrate stabilization of the repetition frequency with an in-loop rms timing jitter of 10 fs, integrated over a bandwidth from 1 Hz to 100 kHz. This represents what is to our knowledge the first time an EOM has been introduced inside a mode-locked laser cavity for fast servo action and the lowest timing jitter reported for a mode-locked fiber laser.     

基于双音外差的电光相位调制器半波电压自校准测量方法

电光相位调制器是光纤通信系统、微波光子系统和相干光通信系统中的关键器件之一. 作为器件本征参数, 电光相位调制器的半波电压通常利用光谱方法和电谱方法进行测量. 光谱方法受到光源线宽和光谱仪分辨率限制, 测量的分辨率较低; 电谱方法则需要光电检测之前将相位调制转换成强度调制, 电谱方法的主要困难在于需要对探测器的不平坦响应进行额外校准. 提出了利用双音外差实现电光相位调制器半波电压自校准测量新方法, 该方法利用双音电光相位调制的边带与移频光载波的外差拍频, 对外差拍频信号进行频谱分析, 获得电光相位调制器的半波电压; 通过设定双音调制信号的频率关系, 克服了探测器光电转换中的不平坦频率响应, 实现了自校准测量. 该方法可扩展探测器和频谱仪的测试频率两倍以上, 节省至少一半的带宽需求. 与光谱测量方法相比, 该方法测试分辨率大幅提高且避免了光源线宽的影响; 与传统电域测量方法相比, 该方法无须额外校准, 无驱动功率和工作波长限制, 且对测试仪器带宽需求降低一半以上. 实验证实了所提方法获得的电光相位调制器半波电压的测量结果与光谱分析法获得的结果一致, 且大幅度地提高了测量范围和分辨率. 该方法提供了非常简单的电光相位调制器微波特性化分析方法, 对其他光电子器件分析也提供了参考.     

Novel 60 GHz RoF system with optical single sideband mm-wave signal generation and wavelength reuse for uplink connection

In order to improve RF frequency to achieve higher bandwidth and larger capacity, we propose a novel scheme to generate optical single sideband (SSB) millimeter-wave, in which frequency doubling of local radio frequency (RF) is obtained by using one integrated Mach–Zehnder modulator (MZM), and we theoretically investigate the generating principle of SSB. The optical SSB modulation scheme is employed to generate 60 GHz optical mm-wave and the 2.5 Gb/s baseband signal is simultaneously up-converted at the central station (CS) for downlink transmission, and the optical carrier is reused for uplink connection at the base station (BS). The full-duplex 2.5 Gb/s data are successfully transmitted over 40 km standard single-mode fiber (SMF-28) for both uplink connection and downlink connection with less than 2-dB power penalty. Results show the novel 60 GHz RoF system with optical SSB mm-wave signal generation using optical frequency doubling is feasible and we can obtain simple cost-efficient configuration and good performance over long-distance transmission.     

Actively mode-locked fiber ring laser by intermodal acousto-optic modulation

We report an actively mode-locked fiber ring laser. A simple and low-insertion-loss acousto-optic modulator driven by standing flexural waves, which couples core-to-cladding modes in a standard single-mode optical fiber, is used as an active mechanism for mode locking. Among the remarkable features of the modulator, we mention its high modulation depth (72%), broad bandwidth (187 GHz), easy tunability in the optical wavelength, and low insertion losses (0.7 dB). The narrowest optical pulses obtained were of 95 ps time width, 21 mW peak power, repetition rate of 4.758 MHz, and 110 mW of pump power.     

Cost-effective and dispersion-tolerant cascade modulation for millimeter-wave-over-fiber applications

In millimeter-wave-over-fiber (MWoF) feeder systems, the received millimeter-wave signals at the remote antennas (RAs) can suffer from signal fading by chromatic dispersion of optical fiber. This can be substantially mitigated by Mach-Zehnder modulator (MZM) based photonic up-conversion technique. In this technique, the data signals at intermediate frequency (IF) are frequency up-converted to millimeter-wave frequency by an MZM biased at its transmission null point. However, this scheme requires a costly, high-speed MZM, which will hinder the widespread of this technique for cost-sensitive MWoF applications. Hence, we propose and demonstrate a cost-effective way of reducing the cost of MWoF optical transmitters based on photonic up-conversion technique. We employ a dual wavelength source composed of a directly modulated laser and a polarimetric filter. This source is used to generate a millimeter-wave tone signal and to frequency up-convert the IF data signals to millimeter-wave frequency. The dual wavelength source is also shared with numerous RAs for further cost reduction. Our experimental demonstration performed with 30 Msymbol/s 16-quadrature amplitude modulation signals shows that we can transmit the 20 GHz millimeter-wave signals over 25 km standard single-mode fiber without any transmission penalty.     

Experimental research on an arbitrary pulse generation system for imaging VISAR

Imaging VISAR is an important diagnostic tool for a variety of shock-related phenomena in laser-driven experiments. To adapt to various types of shaped driven pulse, the imaging VISAR needs an illuminating light with good shaping capability. Here, a flexible laser probe system was experimentally studied. Being generated from a 1064-nm DFB laser, the continuous wave was modulated by a waveguide amplitude modulator driven by 10 GS/s arbitrary waveform generator. After being amplified by fiber amplifiers and Nd:YAG rod amplifiers, the signal pulse was frequency-converted to 532-nm green light by a thermally controlled LBO crystal with a final output energy larger than 10 mJ. Finally, the green light was coupled into a 1-mm core diameter, multimode fused silica optical fiber and propagated to the imaging VISAR. The probe laser could realize accurate pulse shaping with time resolution below 100 ps. Uniformity in intensity and capability of arbitrary pulse shaping provides great convenience for the analysis of experimental data.     

光纤激光经过模清洁器后的强度噪声分析

对1560 nm单频光纤激光光源通过一个光学模清洁器后的强度噪声进行了分析研究.实验观察到模清洁器虽然对于激光的高频强度噪声有明显的抑制作用,但强度噪声特性随频率呈一定周期变化,且在低频处模清洁器对强度噪声有放大作用.本文认为这是由于模清洁器具有类似于光纤延迟线的时延效应,将激光源的部分相位噪声转化为强度噪声.通过理论分析,由相位噪声转化的相对强度噪声幅度与激光相干时间、模清洁器的平均延时参数以及分析频率相关.分析结果与实验测量结果符合良好.此外,通过在光路中加入声光调制器进行反馈调制,激光的线宽从26 kHz压窄至16 kHz,模清洁器的锁定质量明显提高,经过模清洁器后的激光强度噪声有所减小,与理论相符.该结果进一步证实了由相位噪声转化而来的强度噪声与模清洁器的锁定质量无直接关系.通过该研究,完善了光学模清洁器对激光的噪声抑制模型.     

光纤陀螺的噪声及其实验分析

通过对FOG-110-I全光纤陀螺仪样机的研制,分析了光纤陀螺的噪声源,并对信号光背向反馈进入激光器引起的强度噪声和由光纤PZT位相调制器引起的幅度调制对光纤陀螺系统的影响作了重点分析。最后,给出了FOG-110-I全光纤陀螺样机的测试结果和实验分析。     

用于光频传递的通信波段窄线宽激光器研制及应用

通信波段窄线宽激光器在基于光纤的光学频率传递中有着重要应用. 本文报道了1550 nm超窄线宽光纤激光器的研制及其在光学频率传递中的初步应用结果. 利用一台激光光源, 分别锁定到两个参考腔上(精细度分别为344000和296000), 锁定后经拍频比对测得单台激光线宽优于1.9 Hz, 秒级频率稳定度为1.7×10^-14, 优于国内同类报道. 将研制的超窄线宽激光器用于光纤光学频率传递, 在50 km光纤盘上实现了 7.5×10^-17/s的传递稳定度, 较采用商用光纤激光器提高了3.2倍.