Na3AlF6-Al2O3熔盐体系中ZnFe2O4基阳极的电化学行为

研究了ＺｎＦｅ２Ｏ４基阳极在Ｎａ３ＡｌＦ６－Ａｌ２Ｏ３熔盐体系中的电化学稳定性，讨论了电极的析氧历程并得到了析氧过电位与阳极表观电流密度之间的Ｔａｆｅｌ关系式，η＝０．１２＋０．０５２ｌｏｇｉ（ｉ＝０．０１５－０．４４Ａ／ｃｍ＾２）用三角波电位扫描法测定了电极析氧过程的伏安曲线。     

Na_3AlF_6-LiF-RE_2O_3体系表面张力的研究

用最大气泡压力法,采用三因子一次回归正交设计,研究了Na_3AlF_6-LiF-RE_2O_3体系的表面张力,得出表面张力(Y)与RE_2O_3含量(c_1)、LiF含量(c_2)及溶体温度(t)的回归方程如下:Y=260.78 4.088c_1 0.073c_2 0.557c_1c_2-0.136t-0.00483c_1t-0.00050c_2t。     

ZnFe2O4基惰性阳极在微型槽铝电解中的腐蚀行为

在960℃下,改变电解质分子比、阳极电流密度、电解质中氧化铝浓度,对ZnFe2O4基惰性阳极材料在微型槽铝电解中的腐蚀行为进行了考察.实验证明ZnFe2O4基阳极材料在电解过程中的腐蚀,随电解质中氧化铝浓度的升高、阳极电流密度的提高、电解质分子比的降低而减少.当电解质中氧化铝达到饱和时,在足够高的电流密度下,腐蚀趋向于一个最低值.     

铝电极在LiNO3-KNO3熔盐中的电化学行为

采用循环伏安和恒电位电解法考察了铝电极在LiNO3-KNO3熔盐中的电化学行为. 实验结果表明, 在该熔盐中, 锂离子在铝电极上的电还原过程伴随着新生态的锂原子向电极内部的随后扩散步骤; 锂原子进入铝电极后与铝发生合金化, 形成β-LiAl合金和γ-LiAl合金; 锂离子在铝电极上的还原过程受还原态锂在铝基体内的扩散步骤控制. 循环伏安实验发现, 铝电极在该熔盐中的氧化和还原峰电流都先随循环次数增加而增大, 最后基本上趋于稳定. 这表明铝电极在该熔盐体系中具有较好的电化学稳定性.     

Na_3AlF_6-AlF_3熔盐中Ti(Ⅳ)的阴极还原机理

应用循环伏安法和计时电位法研究了在990℃下Na3AlF6-AlF3熔盐中,TiO2钨丝电极上的阴极还原机理.实验表明,Ti(Ⅳ)电沉积过程分两步进行:即首先是Ti(Ⅳ)还原为Ti(Ⅱ),然后Ti(Ⅱ)再还原为金属钛,可表示为:Ti(Ⅳ)→Ti(Ⅱ)→Ti.     

NO_x储存催化剂Pt/BaAl_2O_4-A1_2O_3的XAFS研究

采用共沉淀－浸渍法在不同载体焙烧温度下,制备了不同Ａｌ／Ｂａ原子比的Ｐｔ／ＢａＡｌ２Ｏ４－Ａ１２Ｏ３系列样品。用ＸＲＤ,ＸＡＮＥＳ,ＥＸＡＦＳ,以及ＮＳＣ（ＮＯ_ｘ　ｓｔｏｒａｇｅ ｃａｐａｃｉｔｙ）测定等手段对样品的微观结构和ＮＯ_ｘ储存性能进行了详细的表征．样品中Ｂａ物种是以ＢａＡｌ２Ｏ４和ＢａＣＯ３两种混合物相的形式存在,且伴随着载体焙烧温度和Ｂａ含量的降低,ＢａＡｌ２Ｏ４物相的分散度变高,ＮＯ_ｘ储存活性也随之提高,这表明ＢａＡｌ２Ｏ４相的分散度与样品的ＮＯ_ｘ储存性能密切相关,小颗粒的ＢａＡｌ２Ｏ４相是ＮＯ_ｘ的主要储存活性中心．在样品中,Ｐｔ物种以金属原子簇形式存在．分散度很高,其Ｐｔ—Ｐｔ壳层配位数较标样Ｐｔ粉有显著下降,Ｐｔ—Ｐｔ键长变短,出现了纳米收缩现象．高分散的小颗粒金属Ｐｔ原于簇为捕获和氧化ＮＯ_ｘ的主要活性中心．     

CoTiO3改性K2FeO4电极的电化学行为

CoTiO3改性K2FeO4电极的电化学行为;K2FeO4;CoTiO3;改性电极; 放电电位     

γ-Al_2O_3负载Cr促进SO_4~(-2)/ZrO_2固体超强酸研究

将 Cr促进的 SO2 - 4 /Zr O2 ( SZ)固体超强酸 Cr-SZ负载于 γ-Al2 O3载体上 ,制成 Cr-SZ/Al2 O3系列固体超强酸 ,利用探针反应考察了其超强酸性、中强酸性和弱酸性的变化情况 .详细研究了样品的比表面、硫含量、 Zr O2 晶化情况及正丁烷低温异构化反应活性 .结果发现 ,负载后部分 Cr-SZ的正丁烷低温异构化反应活性显著提高 .含铬样品酸强度和脱氢性能的增强对其正丁烷异构化反应活性的提高均有贡献 .样品酸性和脱氢性之间的合适匹配使 Cr-SZ/Al2 O3显示出很高的正丁烷异构化反应活性 .     

磷酸钒钠Na_3V_2(PO_4)_3电化学储能研究进展

锂离子电池在全球范围内的广泛应用加剧了对锂资源的消耗,其成本和原料将限制其未来发展。钠与锂具有相似物理化学性质,并且储量丰富。根据锂离子"摇椅式"电池原理,富钠离子化合物可类似富锂离子正极材料,提供可脱嵌的钠离子及结构。钠离子较锂离子大,其可逆脱嵌反应要求材料结构具有较大的容钠位与离子迁移通道。聚阴离子体磷酸钒钠Na_3V_2(PO_4)_3属于钠离子超导体(NASICON)材料,其NASICON结构骨架形成了稳定的容钠位,并且开放的三维离子迁移通道利于提高钠离子的扩散。Na_3V_2(PO_4)_3作为电池正极材料,具有理想的比容量、电压平台与循环稳定性,从而受到了广泛关注。本文首先介绍了Na_3V_2(PO_4)_3结构特点,其次结合团队已有的工作基础对Na_3V_2(PO_4)_3在钠离子电池、混合离子电池、水系电池,混合超级电容器等体系中的应用与反应机理进行了阐述;总结了基于Na_3V_2(PO_4)_3设计的复合材料与结构并探讨了Na_3V_2(PO_4)_3可能存在的问题与未来发展趋势。     

AlCl3(ZnCl2,MgCl2)对Sm2O3的氯化效果及电化学行为

研究了AlCl_3(ZnCl_2、MgCl_2)对Sm_2O_3的氯化效果以及Sm_2O_3在Li Cl-KCl-AlCl_3(ZnCl_2、MgCl_2)熔盐体系中的电化学行为。在Li Cl-KCl-Sm_2O_3熔盐中加入AlCl_3(ZnCl_2、MgCl_2)后,ICP测量结果表明,AlCl_3体系中Sm(Ⅲ)离子的浓度最高,并且在923 K时达到最大值;固相反应表明,AlCl_3氯化Sm_2O_3生成SmCl_3,而Sm_2O_3和ZnCl_2(MgCl_2)反应生成Sm OCl。电化学行为表明,AlCl_3体系中观察到了两种Al-Sm的合金峰,而ZnCl_2体系中只观察到Zn-Sm金属间化合物的形成峰,MgCl_2体系中没有形成合金。在-6.25 A·cm~(-2)下,W电极上恒电流电解2 h获得了Al-Li-Sm合金,经XRD分析,合金为Al_2Sm相。     

Alumina Solubility in Na3AlF6-K3AlF6-AlF3 Molten Salt System Prospective for Aluminum Electrolysis at Lower Temperature

The alumina solubility in the title system within the composition range of KR{m(K₃AlF₆)/[m(K₃AlF₆)+ m(Na₃AlF₆)]} 10%―50%, a ternary Na₃AlF₆-K₃AlF₆-AlF₃ molten system with 23%―29%(mass fraction) AlF₃ was investigated by measuring the mass loss of a rotating sintered corundum disc. And the following empirical equation was derived when superheat degree was no more than 60 ℃: w(Al₂O₃)_sat=A×(T/1000)^B, where A= –1.85774+ 26.754234w(AlF₃)^–0.3683–0.00783KR^2.363+0.010266KR^2.3048+0.7902w(AlF₃)^0.00652, B=112.4625–53.2567w(AlF₃)^0.4236+ 5.1079w(AlF₃)^0.9241+0.01542w(AlF₃)^1.3540. Considering both higher alumina solubility and not too high superheat degree are required, alumina solubility of different compositions at not the same temperature but the same superheat degree was studied, which will be more industrial helpful for selecting prospective compositions. The results show that the composition deserved to be further tested in lower temperature cells is 10%―30% KR and 23%―26%(mass fraction) AlF₃.     

Liquidus Temperatures of System Na3AlF6-K3AlF6-AlF3 for Aluminum Electrolysis at Lower Temperature

Liquidus temperatures in the molten salt system Na3AlF6-K3AlF6-AlF3 of interest for aluminum electrolysis were determined by thermal analysis method. The results were presented and an empirical equation describing liquidus temperatures for primary crystallization was derived t=1003.5–0.081×A2.3159–5.87×B0.657–0.024×A2.22×B1.14+ 0.035×A2.17×B1.084, where t is the liquidus temperature in degree Celsius, A denotes the mass fraction of AlF3 in system Na3AlF6-K3AlF6- AlF3, and B denotes K3AlF6/(Na3AlF6+K3AlF6 ) in mass(%, the value was defined as KR in this paper). The composition limitations are 0相似文献   

Comparison of reduction behavior of Fe2O3, ZnO and ZnFe2O4 by TPR technique

Advanced integrated gasification combined cycle (IGCC) power generation systems require the development of high-temperature,regenerable,desulfurization sorbents capable of removing hydrogen sulfide from coal gasifier gas to very low levels.As a sort of effective desufurizer,such as Fe2O3,ZnO and ZnFe2O4,it will endure strong reducing atmosphere in desulfurization process.The reduced degree of desufurizer can have an effect on its desulfurization reactivity.In this paper,Fe2O3,ZnO and ZnFe2O4 were synthesized by precipitation or co-precipitation at constant pH.After aging,washing and drying,the solids were calcined at 800℃.The reduction behaviors of sample were characterized by temperature-programmed reduction (TPR).It is found that there are two reduction peaks for Fe203 in TPR,and whereas no reduction peaks for ZnO are found.The reduction process of ZnFe2O4 prepared by co-precipitation is different from that of Fe2O3.ZnFe2O4 is easier to be reduced than Fe2O3.The activation energy of reduction process for Fe2O3 and ZnFe2O4 is obtained at different reduction periods.     

氧化铟掺杂对ZnFe2O4半导体气敏性能的影响

用化学共沉淀法在ＺｎＦｅ２Ｏ４中掺入Ｉｎ２Ｏ３．Ｘ射线衍射分析证实，Ｉｎ２Ｏ３与ＺｎＦｅ２Ｏ３之间没有新相生成，晶格常数有微小变化．掺入Ｉｎ２Ｏ３降低了ＺｎＦｅ２Ｏ４的电导，改变了该系列材料的导电机制，提高了材料对乙醇的敏感性和选择性，而且缩短了材料的响应时间     

固体超强酸SO2-4/SnO2-Al2O3的红外光谱研究

以四氯化锡、硫酸铝为原料,氨水为沉淀剂,采用共沉淀法制得新型固体超强酸SO2-4/SnO2-Al2O3.采用FT-IR技术考察了金属元素摩尔比、焙烧温度、浸渍液以及掺杂稀土氧化物对该固体超强酸结构和性能的影响.FT-IR结果表明在该固体超强酸中,锡和硫酸根是以螯合和桥式两种方式配位结合,其中起催化活化作用的主要是和硫酸根以螯合双齿结合的锡;和SO2-4/ZrO2型超强酸相比,SO2-4/SnO2-Al2O3超强酸的硫酸根FT-IR特征吸收峰发生蓝移,显示出更强的酸性.锡铝摩尔比为9∶1、焙烧温度为773K、焙烧时间为3h时,制得的SO2-4/SnO2-Al2O3样品对酯化反应的催化性能最好.     

熔盐电解LiCl-KCl-AlCl3-La2O3共析出制备Al-Li-La合金

研究了LiCl-KCl-AlCl3-La2O3熔盐体系中共析出制备Al-Li-La合金的可行性。研究表明,在LiCl-KCl熔盐中,AlCl3将La2O3氯化为LaCl3,使电解制备Al-Li-La合金顺利进行。借助循环伏安法对熔盐体系的电化学行为进行分析发现,对质量比为45∶45∶5∶2的LiCl-KCl-AlCl3-La2O3熔盐,当阴极电流密度大于0.25 A/cm2,可以实现Al、Li和La的共析出。通过研究电解温度、阴极电流密度和电解时间对合金组成的影响,得到了较佳的电解参数:电解温度650℃,在LiCl-KCl混合熔盐中加入质量分数为5%的AlCl3和2%的La2O3,阴极电流密度12.5 A/cm2,电解时间1 h。X射线衍射对合金分析测试表明,合金主要由Al2La和βLi组成。     

Na2O或K2O对气相合成1–苯基氮杂环庚烷的CoO/SiO2-Al2O3催化剂的作用

研究了Na2O或K2O对苯胺和1,6己二醇气相合成1-苯基氮杂环庚烷的CoO/SiO2-Al2O3催化剂的作用,并采用X射线衍射、透射电子显微镜、H2-程序升温还原、NH3-程序升温脱附等技术对催化剂进行了表征.结果表明,Na2O助剂能增加催化剂的弱酸中心数,减少中强酸中心数,使催化剂的选择性得到提高.加入K2O使催化剂的弱酸中心数显著减少,并使CoO在反应过程中易于烧结,因此不利于1–苯基氮杂环庚烷的合成.     

Screen‐printed Electrode Modified with ZnFe2O4 Nanoparticles for Detection of Acetylcholine

In this paper a sensor to detect acetylcholine on the basis of ZnFe₂O₄ nanoparticles modified screen printed electrode (SPE) is reported. In the range 0.08–500.0 μM, with the detection limit of 0.024±0.001 μM, acquired anodic peak currents where shown to be linearly dependent on acetylcholine concentrations by differential pulse voltammetry (DPV). It was proven that acetylcholine oxidation at adjusted electrode surface takes place at 100 mV potential less positive compared to an unadjusted screen printed electrode. The electron transfer coefficient (α=0.51) and diffusion coefficient (D=9.3×10^?6 cm²/s) of acetylcholine oxidation were determined too. In addition, this original sensor possesses numerous benefits such as reproducibility, high stability and rapid response (20 s).     

Phase relations in the system ZnV2O6 -ZnFe2O4

Using DTA and XRD methods, a diagram of phase equilibria in ZnV₂O₆-ZnFe₂O₄ system has been constructed. System ZnV₂O₆-ZnFe₂O₄ is in subsolidus area a real binary system and its components form a compound Zn₂FeV₃O₁₁. Zn₂FeV₃O₁₁ melts incongruently at 835±5°C with deposition of two solid phases: b-Zn₂V₂O₇ and ZnFe₂O₄. This revised version was published online in July 2006 with corrections to the Cover Date.