LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and LiCoO<Subscript>2</Subscript> composite cathode materials obtained by mechanical activation

New composite cathode materials xLiMn₂O₄/(1 ? x) LiCoO₂(x = 0.7, 0.6, 0.5 и 0.4) were obtained by mechanical activation. According to scanning electron microscopy data, the process was accompanied by pronounced dispersion and fine mixing of the initial components. In the course of the preparation and electrochemical cycling of the composites, LiMn₂O₄ and LiCoO₂ partially reacted, leading to the replacement of manganese with cobalt in the structure of spinel, which was detected by powder X-ray diffraction (XRD), IR and X-ray photoelectron spectroscopy (XPS), and cyclic chronopotentiometry. The specific discharge capacity of composites was ～100 mAh/g.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

Mesoporous amorphous MnO<Subscript>2</Subscript> as electrode material for supercapacitor

A kind of novel mesoporous, electrochemical active material, amorphous MnO₂ has been synthesized by an improved reduction reaction and using supramolecular as template. The synthesized sample was characterized physically by thermogravimetric analysis, X-ray diffraction, transmission electron microscope (TEM), and Brunauer–Emmett–Teller (BET) surface area measurement, respectively. Electrochemical characterization was performed using cyclic voltammetry and chronopotentiometry in 2 mol/l KOH aqueous solution electrolyte. The results of BET and TEM analysis indicated that supramolecular template plays an important role in the process of big specific surface area mesoporous material forming. After sintering at 200 °C, the sample still remained an amorphous structure, and its specific capacitance reached 298.7 F/g and presented a very stable capacitance after 500 cycles. In addition, the electrochemical process, such as ion transfer and electrical condition, was also investigated with electrochemical impedance spectroscopy.     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

Effects of Ni-ion doping on electrochemical characteristics of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> powders prepared by a spray-drying method

Spinel LiMn_2−x Ni _x O₄ compounds doped with a range of Ni (x=0–0.06) were synthesized by a spray-drying method. The structure and morphology characteristics of the powders were studied in detail by means of X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy. The XRD data reveal that all the samples have well-defined spinel structure, but, with the increase in Ni content, the doped lithium manganese spinels have smaller lattice constant. The undoped and doped spinel LiMn₂O₄ particles are fine, narrowly distributed, and well crystallized. The electrochemical characteristics of the samples are measured in the coin-type cells in a potential range of 3.2–4.35 V vs Li/Li⁺. All cyclic voltammogram curves exhibit two pairs of redox reaction peaks, but, among them, there are some differences about the peak split. With the increase in the Ni content, the specific capacities of the samples decrease slightly, but their cyclic ability increases.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Synthesis,characterization and thermal analysis of polyaniline (PANI)/Co<Subscript>3</Subscript>O<Subscript>4</Subscript> composites

Conducting polyaniline/Cobaltosic oxide (PANI/Co₃O₄) composites were synthesized for the first time, by in situ deposition technique in the presence of hydrochloric acid (HCl) as a dopant by adding the fine grade powder (an average particle size of approximately 80 nm) of Co₃O₄ into the polymerization reaction mixture of aniline. The composites obtained were characterized by infrared spectra (IR) and X-ray diffraction (XRD). The composition and the thermal stability of the composites were investigated by TG-DTG. The results suggest that the thermal stability of the composites is higher than that of the pure PANI. The improvement in the thermal stability for the composites is attributed to the interaction between PANI and nano-Co₃O₄.     

LiMn2O4 nanorods as a super-fast cathode material for aqueous rechargeable lithium batteries

LiMn₂O₄ nanorods were prepared by a facile hydrothermal method in combination with traditional solid-state reactions and characterized by X-ray diffraction analysis. Their electrochemical behavior was tested by cyclic voltammetry and repeated charge/discharge cycling. Results show that the reversible intercalation/deintercalation of Li-ions into/from LiMn₂O₄ cathode can yield up to 110 mAh/g at 4.5 C, and still retains 88% at the very large charge rate of 90 C with well-defined charge and discharge plateaus. It presents very high power density, up to 14.5 kW/kg, and very excellent cycling behavior, 94% capacity retention after 1200 cycles. It is thus a competitor for LiFePO₄.     

Studies of porphyrin zinc compounds intercalated into V<Subscript>2</Subscript>O<Subscript>5</Subscript> xerogel

The intercalation of meso-tetrakis(4-pyridyl)porphyrin zinc, the cationic salts of meso-tetrakis(N-methylpyridinium-4-yl)porphyrin zinc, and zwitterionic meso-tetrakis-[N-(3-sulfonatopropyl)pyridinium-4-yl]porphyrin zinc from aqueous solutions as well as of meso-tetrakis(N-methylpyriclinium-4-yl)porphyrin zinc from pyridine solutions into V₂O₅ xerogel was studied. The intercalation complexes obtained were characterized by X-ray diffraction analysis, TG analysis, IR, and UV reflectance spectroscopy.     

Fabrication and photocatalytic property of TiO<Subscript>2</Subscript> nanofibers

TiO₂ nanofibers were prepared from tetrabutyl titanate sol precursors by using electrospun method. X-ray diffraction (XRD) and atomic force microscope (AFM) were used to characterize their crystal structure and morphology feature. The results demonstrated that TiO₂ nanofibers possessed anatase phase and the average diameter of TiO₂ nanofibers was about 150 nm. The photocatalytic property of TiO₂ nanofibers was evaluated for the photodecomposition of methyl orange solution. And TiO₂ nanofibers exhibited high photocatalytic activities with transfer efficiency about 100% after 20 min.     

Effects of polyvinyl alcohol on the electrochemical performance of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> cathode material

In view of the close relationship between the morphology of LiNi_0.8Co_0.15Al_0.05O₂ (NCA) and its electrochemical performance, polyvinyl alcohol (PVA) was added to control the NCA morphology. And thus a new NCA cathode material modified by PVA (NCA-PVA) was prepared. The morphology and structure of the obtained samples were characterized by X-ray diffraction, scanning electron microscopy, and laser diffraction. The electrochemical performance was characterized with electrochemical workstation and cell tester by assembling into CR2032 coin-type half-cell. The results show that the obtained NCA-PVA has a better layer structure and smaller cation mixing degree, smaller particle size, and more uniform particle size distribution than the pristine NCA without adding PVA. The electrochemical performance is also improved: the initial discharge capacity increases from 143.36 to 184.84 mAh g^?1. And the charge-discharge efficiency increases from 78.25 to 86.42%. The specific discharge capacities of NCA-PVA are all higher than that of the NCA (about 50 mAh g^?1) at all testing rates (0.1, 0.2, 0.5, 1.0, 2.0, and 5.0 C).     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.     

Layered LiNi<Subscript>0.80</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> as cathode material for hybrid Li<Superscript>+</Superscript>/Na<Superscript>+</Superscript> batteries

LiNi_0.80Co_0.15Al_0.05O₂ (NCA) is explored to be applied in a hybrid Li⁺/Na⁺ battery for the first time. The cell is constructed with NCA as the positive electrode, sodium metal as the negative electrode, and 1 M NaClO₄ solution as the electrolyte. It is found that during electrochemical cycling both Na⁺ and Li⁺ ions are reversibly intercalated into/de-intercalated from NCA crystal lattice. The detailed electrochemical process is systematically investigated by inductively coupled plasma-optical emission spectrometry, ex situ X-ray diffraction, scanning electron microscopy, cyclic voltammetry, galvanostatic cycling, and electrochemical impedance spectroscopy. The NCA cathode can deliver initially a high capacity up to 174 mAh g^?1 and 95% coulombic efficiency under 0.1 C (1 C?=?120 mA g^?1) current rate between 1.5–4.1 V. It also shows excellent rate capability that reaches 92 mAh g^?1 at 10 C. Furthermore, this hybrid battery displays superior long-term cycle life with a capacity retention of 81% after 300 cycles in the voltage range from 2.0 to 4.0 V, offering a promising application in energy storage.     

A novel polyoxometalate chain constructed from sandwich lanthanide-containing polyanions [Pr(PW<Subscript>11</Subscript>O<Subscript>39</Subscript>)<Subscript>2</Subscript>]<Superscript>11−</Superscript> and sodium cation linkers

A novel sandwich-type lanthanide polyoxometalate [(CH₃)₄NH]₄Na₃[Pr(PW₁₁O₃₉)₂] · 12H₂O (1) has been synthesized by conventional method and characterized by cyclic voltammetry, IR spectroscopy and single crystal X-ray diffraction. X-ray diffraction result reveals that the sandwich type polyanions are linked by sodium cations to form a structure of zigzag chains, and the chains are further connected into an extensive two-dimensional (2D) framework depending on hydrogen bond. The emission spectrum result shows weak photoluminescence of compound 1. The magnetic studies of compound 1 demonstrate an antiferromagnetic interaction in 1.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Interference blockage of electron tunneling and pseudo-Faraday hypercapacity for C-SiO<Subscript>2</Subscript> nanocomposites

The thermodynamic and kinetic regularities of the intercalation of lithium into C-SiO₂ nanocomposites are studied. The dependence of the differential capacity and kinetic intercalation parameters on the size of nanocomposite particles is established. According to theoretical analysis, the obtained results are explained as resulting from the quantum-mechanical effect of the interference blockage of the tunneling of an electron into a nonmetallic nanoparticle. An impedance model of processes and its parametric identification are given. A new class of electrochemical energy generators is proposed.     

Electronic-Ionic Processes in Bi<Subscript>2</Subscript>Cu<Subscript>0.5</Subscript>Mg<Subscript>0.5</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript> with Pyrochlore Structure

Solid solution Bi₂Cu_0.5Mg_0.5Nb₂O_9–δ with the pyrochlore structure is synthesized by three different methods. Its structure and chemical composition are confirmed by X-ray diffraction analysis, electron microscopy, and energy-dispersive spectroscopy. The electronic-ionic processes are studied by the method of impedance spectroscopy in the frequency range from 0.3 Hz to 1.0 MHz and the temperature range from 0 to 340°С. The data are processed with the use of ZView program. Electrochemical models of samples are obtained in the form of equivalent circuits. The sign of the main charge carrier is determined by the thermo-emf method. Nonlinear effects are studied based on voltammetric characteristics. It is found that at room temperature, the charge in samples is transferred by electrons and cations (presumably, copper). In the temperature range of 260–300°С, the capacitance of samples and the specific conductivity of their volume demonstrate local minimums. Insofar as at these temperatures the oxygen conduction may occur, it is assumed that associates of anions and cations are formed. The decrease in the concentration of charge carries is confirmed by sample’s equivalent circuit into which the Gerischer impedance is introduced to enhance the accuracy. It is shown that at t = 260°С, the lifetime of charge carriers is the minimum.     

Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

Heavy metal removal using SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> binary oxide: experimental design approach

Sorption of Ni²⁺ and Cd²⁺ as heavy metals ions at the interface of the binary oxide TiO₂-SiO₂ was investigated. In addition, physical properties of TiO₂-SiO₂ matrices such as BET surface area, X-ray diffraction, and point of zero charge (pH_PZC) were measured. Statistical design of experiments was applied to find the conditions of sorption at which the maximum heavy metal removal was achieved. A second order polynomial function was used to correlate the independent variables (pH, metal ion concentration, and shaking time) and response (heavy metal removal). Values of regression parameters were determined by the computer program, Design expert^® (Stat-Ease Inc.). The quality of fit of the polynomial model equation was expressed by the regression coefficient R ². The sorption results showed that the pH is the most significant factor. In turn, the sorbed percentage reached 100% at high initial concentration and long shaking times due to formation of hydroxyl compounds between the ions and TiO₂-SiO₂ matrices. The results show that there is a Gaussian (normal) distribution of residuals (squared differences between experimentally observed and predicted values from the model), and also that the differences between observed and predicted values are in the range of ±5%. These indicate that experiments were well-conducted and the results have no significant error.