Compression of CdCu3Ti4O12 perovskite to 55 GPa

Synchrotron x-ray diffraction measurements of CdCu₃Ti₄O₁₂ (CDCTO) were performed up to 55.5 GPa. There is no structural phase transformation in this pressure range. The irregular curvature shifts of the P-V curve are attributed to the grain surface effect. Analysis indicates that the grain surface of CDCTO is stiffer than the grain interior at higher pressures. We point out that the atoms on grain surfaces must be either densely packed or have a strong correlation with the gain interior in order to have a high dielectric constant, as in CaCu₃Ti₄O₁₂. The derived bulk modulus of CDCTO is approximately 235±7 GPa with K^′=5.1±0.4.     

Electronic Structure and Elastic Properties of Ti3AlC from First-Principles Calculations

We perform a first-principles study on the electronic structure and elastic properties of TiaA1C with an antiperovskite structure. The absence of band gap at the Fermi level and the finite value of the density of states at the Fermi energy reveal the metallic behavior of this compound. The elastic constants of Ti3AlC are derived yielding c11 = 356 GPa, c12 = 55 GPa, c44 = 157 GPa. The bulk modulus B, shear modulus G and Young＇s modulus E are determined to be 156, 151 and 342 GPa, respectively. These properties are compared with those of Ti3AlC2 and Ti2AlC with a layered structure in the Ti-Al-C system and FeaAlC with the same antiperovskite structure.     

Electronic and elastic properties of the superconducting nanolaminate Ti<Subscript>2</Subscript>InC

The electronic properties and elastic parameters of the superconducting nanolaminate Ti₂InC are analyzed using the ab initio full-potential linearized augmented-plane-wave (FLAPW) method with the generalized gradient approximation (GGA) of the local spin density. The equilibrium parameters of the crystal lattice, the band structure, the total and partial densities of states, and the Fermi surface are determined within a unified approach. The independent elastic constants, the bulk modulus, and the shear modulus are calculated, and the elastic parameters are numerically estimated for the first time for polycrystalline Ti₂InC.     

Structural, electronic and elastic properties of M2SC (M = Ti, Zr, Hf) compounds

Using ab initio calculations, we have studied the structural, electronic and elastic properties of M₂SC, with M = Ti, Zr and Hf. Geometrical optimization of the unit cell are in good agreement with the available experimental data. The band structures show that all three materials are conducting. The analysis of the site and momentum projected densities shows that the bonding is achieved through a hybridization of M-atom d states with S and C-atom p states. The Md-Sp bonds are lower in energy and are stiffer than Md-Cp bonds. The elastic constants are calculated using the static finite strain technique. We derived the bulk and shear moduli, Young's moduli and Poisson's ratio for ideal polycrystalline M₂SC aggregates. We estimated the Debye temperature of M₂SC from the average sound velocity. This is a quantitative theoretical prediction of the elastic properties of Ti₂SC, Zr₂SC, and Hf₂SC compounds, and it still awaits experimental confirmation.     

First-principles studies of the electronic and elastic properties of Ti2GeC

We have performed first-principles studies on electronic structure and elastic properties of Ti₂GeC. The calculated band structure shows that this compound is electrical conductor. From the pressure dependence of elastic constants, we find that Ti₂GeC is most stable in the pressure range from 0 to 100 GPa. The strong Ti 3d, Ge 4p and C 2p hybridization may stabilize the structure of Ti₂GeC. By analyzing the ratio between the bulk and shear moduli, we conclude that Ti₂GeC is brittle in nature, and the brittleness of Ti₂GeC originated from the large value of Ti atom occupying the internal parameter z.     

Ab initio study of Nb2SC and Nb2S2C: Differences in coupling between the S and Nb-C layers

Using ab initio calculations, we have studied the structurally related compounds Nb₂SC and Nb₂S₂C. In Nb₂S₂C (space group , prototype Bi₂Te₃), S atoms are nearest neighbours, while in Nb₂SC (space group P6₃/mmc, prototype Cr₂AlC) this is not the case. The calculated equilibrium volume for these two phases deviates by 1.6-3.7% to previously-published experimental data and the bulk modulus-to-c₄₄ ratios obtained are 1.5 and 5.9, respectively. These results indicate a resemblance of Nb₂S₂C to hexagonal BN and graphite. Furthermore, we have demonstrated that the uniform compression method is adequate for estimating the elastic properties of Nb₂SC, a so-called MAX phase. It is our ambition that these calculations will stimulate further experimental research on these compounds.     

Ab initio calculations of elastic constants and thermodynamic properties of Li2O for high temperatures and pressures

The elastic constants and thermodynamic properties of Li₂O for high temperatures and pressures are calculated by the ab initio unrestricted Hartree-Fock (HF) linear combination of atomic orbital (LCAO) periodic approach. The lattice constant, elastic constants, Debye temperature, and thermal expansion coefficient obtained are in good agreement with the available experimental data and other theoretical results. It is found that at zero pressure the elastic constants C₁₁, C₁₂ and C₄₄, bulk modulus B and Debye temperature Θ_D decrease monotonically over the wide range of temperatures from 0 to 1100 K. When the temperature , C₁₂ approaches zero, consistently with the transition temperature 1200 K. However, with increasing pressure, they all increase monotonically and the anisotropy will weaken.     

First principles study of structural,electronic, mechanical and thermal properties of A15 intermetallic compounds Ti3X (X=Au,Pt, Ir)

The structural, electronic, elastic, mechanical and thermal properties of Ti₃Au, Ti₃Pt and Ti₃Ir intermetallic compounds crystallizing in A15 structure have been studied using density functional theory within generalized gradient approximation (GGA) for the exchange correlation potential. Elastic properties such as Young's modulus (E), rigidity modulus (G), bulk modulus (B), Poisson's ratio (σ) and elastic anisotropic factor (A) have been calculated. From the present study it is noted that Ti₃Ir is the hardest compound among the three materials studied due to its larger bulk modulus. Also, it is more ductile in nature.     

Structural, elastic and electronic properties of a new ternary-layered Ti2SiN

The structural, elastic and electronic properties of Ti₂SiN were studied by first-principle calculations. The calculated bond lengths of Ti-Si and Ti-C are 2.65 and 2.09 Å, respectively. The results show Ti₂SiN is mechanically stable, and its bulk modulus B, shear modulus G, Young's modulus E, Poisson's ratio μ and anisotropy factor A are determined to be 182 GPa, 118 GPa, 291 GPa, 0.233 and 1.57, respectively. The calculated electronic structure indicates that Ti₂SiN is anisotropic and conductive.     

Theoretical study of the structural, elastic, electronic and thermal properties of the MAX phase Nb2SiC

Structural, elastic, electronic and thermal properties of the MAX phase Nb₂SiC are studied by means of a pseudo-potential plane-wave method based on the density functional theory. The optimized zero pressure geometrical parameters are in good agreement with the available theoretical data. The effect of high pressure, up to 40 GPa, on the lattice constants shows that the contractions along the c-axis were higher than those along the a-axis. The elastic constants C_ij and elastic wave velocities are calculated for monocrystal Nb₂SiC. Numerical estimations of the bulk modulus, shear modulus, Young’s modulus, Poisson’s ratio, average sound velocity and Debye temperature for ideal polycrystalline Nb₂SiC aggregates are performed in the framework of the Voigt-Reuss-Hill approximation. The band structure shows that Nb₂SiC is an electrical conductor. The analysis of the atomic site projected densities and the charge density distribution shows that the bonding is of covalent-ionic nature with the presence of metallic character. The density of states at Fermi level is dictated by the niobium d states; Si element has a little effect. Thermal effects on some macroscopic properties of Nb₂SiC are predicted using the quasi-harmonic Debye model, in which the lattice vibrations are taken into account. The variations of the primitive cell volume, volume expansion coefficient, bulk modulus, heat capacity and Debye temperature with pressure and temperature in the ranges of 0-40 GPa and 0-2000 K are obtained successfully.     

Electronic and elastic properties of a double perovskite slab-rocksalt layer of Eu2SrAl2O7 investigated by LSDA+U

The electronic structure and elastic properties of a double perovskite slab-rocksalt layer compounds of Eu₂SrAl₂O₇ were calculated by local- (spin-) density approximation [L(S) DA] band theory with Hubbard term of U. We used and for the calculations. The band gap of Eu₂SrAl₂O₇ is 4.8 eV. Both of Eu-O and Al-O bonds have strong covalent character and Sr-O is a perfect ionic bond. The full set elastic constants indicate the elastic modulus of Eu₂SrAl₂O₇ is 224 and 240 GPa by calculation and experiment, respectively.     

First principles studies on the elastic,thermodynamic properties and electronic structure of Ti15−xMoxSn compounds

The structural, elastic, thermodynamic and electronic properties of the Ti_15−xMo_xSn compounds were systematically investigated by means of first-principles calculations based on the density functional theory (DFT). The calculated results demonstrate the Ti_15−xMo_xSn compounds still remain the stable β phase structure. The calculation of cohesive energy shows that the structural stability of the Ti_15−xMo_xSn compounds increases apparently with the increase of Mo content. According to Hooke's law, the single crystal elastic constants were obtained and show that all the calculated compounds keep mechanical stability. Then the bulk modulus B, shear modulus G, Young's modulus E and Poisson's ratio ν of polycrystalline aggregates were calculated at zero pressure. The calculated results show that among these Ti_15−xMo_xSn compounds, Ti₄Mo₁₁Sn exhibits the largest stiffness while Ti₁₂Mo₃Sn shows the greatest ductility. The compounds Ti₁₂Mo₃Sn and Ti₁₁Mo₄Sn with the two lowest elastic Young's modulus of 61.01 GPa and 65.59 GPa are expected to be promising metallic biomaterials for implant applications. Besides, the Debye temperature Θ_D and the electronic density of states (DOS) are also investigated and discussed.     

Crystal structure and compressibility of a high-pressure Ti-rich oxide, (Ti0.50Zr0.26Mg0.14Cr0.10)O1.81, isomorphous with cubic zirconia

A Ti-rich oxide, (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)_∑=1.0O_1.81, was synthesized at 8.8 GPa and 1600 °C using a multi-anvil apparatus. Its crystal structure at ambient conditions and compressibility up to 10.58 GPa were determined with single-crystal X-ray diffraction. This high-pressure phase is isomorphous with cubic zirconia (fluorite-type) with space group Fm3¯m and unit-cell parameters a=4.8830(5) Å and V=116.43(4) Å³. Like stabilized cubic zirconia, the structure of (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 is also relaxed, with all O atoms displaced from the (, , ) position along 〈1 0 0〉 by 0.319 Å and all cations from the (0, 0, 0) position along 〈1 1 1〉 by 0.203 Å. No phase transformation was detected within the experimental pressure range. Fitting the high-pressure data (V vs. P) to a third-order Birch-Murnaghan EOS yields K₀=164(4) GPa, K′=4.3(7), and V₀=116.38(3) Å³. The bulk modulus of (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 is significantly lower than that (202 GPa) determined experimentally for cubic TiO₂ or that (~210 GPa) estimated for cubic ZrO₂. This study demonstrates that cubic TiO₂ may also be obtained by introducing various dopants, similar to the way cubic zirconia is stabilized below 2370 °C. Furthermore, (Ti_0.50Zr_0.26Mg_0.14Cr_0.10)O_1.81 has the greatest ratio of Ti⁴⁺ content vs. vacant O²⁻ sites of all doped cubic zirconia samples reported thus far, making it a more promising candidate for the development of electrolytes in solid oxide fuel cells.     

Structural transition of Ti3SiC2 under high hydrostatic pressure: A first-principles study

We theoretically studied the phase transformation, electronic and elastic properties of Ti₃SiC₂ ceramic by using the pseudopotential plane-wave method within the density functional theory. Our results demonstrate that there exists a structural phase transition from α‐Ti₃SiC₂ to β‐Ti₃SiC₂ under pressure up to 384 GPa, and α‐Ti₃SiC₂ is the most stable phase at zero pressure. The calculated electronic band structure and density of states reveal the metallic behavior for the polymorphs of Ti₃SiC₂. The mechanical stability of α‐Ti₃SiC₂ at zero pressure is confirmed by the elastic constants, and is analyzed in terms of electronic level. By analyzing the ratio between bulk and shear moduli, we conclude that α‐Ti₃SiC₂ is brittle in nature.     

Ab initio calculation of the electronic structure,Fermi surface,and elastic properties of the new 7.5-K superconductor Nb<Subscript>2</Subscript>InC

Ab initio calculations were performed to investigate electronic and elastic properties of the newly discovered 7.5 K superconductor: layered Nb₂InC. As a result, electronic bands, total and site-projected l—decomposed density of states at the Fermi level, shape of the Fermi surface for Nb₂InC were obtained for the first time. Besides, independent elastic constants, bulk modulus, compressibility, shear modulus, Young’s modulus, Poisson’s ratio together with the elastic anisotropy parameters and indicator of brittle/ductile behavior of Nb₂InC were evaluated and analyzed in comparison with the available data.     

Fermi surfaces and quasi-particle band dispersions of the iron pnictides superconductor KFe2As2 observed by angle-resolved photoemission spectroscopy

We have performed an angle-resolved photoemission study of the iron pnictide superconductor KFe₂As₂ with . Most of the observed Fermi surfaces show almost two-dimensional shapes, while one of the quasi-particle bands near the Fermi level has a strong dispersion along the k_z direction, consistent with the result of a band-structure calculation. However, hole Fermi surfaces α and ζ are smaller than those predicted by the calculation while other Fermi surfaces are larger. These observations are consistent with the result of a de Haas-van Alphen study and a theoretical prediction on inter-band scattering, possibly indicating many body effects on the electronic structure.     

High pressure X-ray diffraction study on icosahedral boron arsenide (B12As2)

The high pressure properties of icosahedral boron arsenide (B₁₂As₂) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B₁₂As₂ retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B₁₂As₂—c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.     

Theoretical investigations on the elastic and thermodynamic properties of Ti2AlC0.5N0.5 solid solution

We have performed theoretical studies on the elastic and thermodynamic properties of the solid solution: Ti₂AlC_0.5N_0.5. The lattice parameters, elastic constants, bulk, shear, Young's moduli, Poisson's ratio and Debye temperature were calculated and compared with those of the end members, Ti₂AlC and Ti₂AlN. The temperature dependence of the bulk moduli, thermal expansion coefficient and specific heats of Ti₂AlC_0.5N_0.5 were obtained from the quasi-harmonic Debye model. The calculated elastic and thermodynamic properties were compared with experimental data.     

Superconductivity of proximity coupled superconductor-antiferromagnetic multilayers

Nucleation of superconducting phase in proximity coupled superconductor(SC)-antiferromagnetic(AF) multilayers is studied theoretically. For SC layer we use the usual Usadel equations. As an AF layer we consider a normal metal which undergos the magnetic phase transition associated with the nesting electron and hole Fermi surfaces. The basic formalism, suitable for study of the SC phase of the SC/AF system is presented. The superconducting transition temperature,T _c , and upper critical fields,H _c2‖ (T) andH _c2⊥ (T) have been calculated.     

Crystal structure, electronic and elastic properties for novel Hf3AlN and Zr3AlN ceramics explored by first principles studies

Investigations into crystal structure, electronic and elastic properties of M₃AlN (M=Hf, Zr) had been conducted by plane-wave pseudopotential calculations. The absence of band gap at the Fermi level and the finite value of the density of states at the Fermi energy reveal the metallic behavior of these two compounds. The charge density distributions and density of states indicate that there exist relatively soft Al-M and strong N-M covalent bonds, which might be contributed to layered chemical bonding character of M₃AlN. By analyzing Cauchy pressure and the bulk modulus to C₄₄ ratio, Hf₃AlN was predicted to be more ductile than Zr₃AlN.