FT-Raman and photoacoustic infrared spectroscopy of syncrude light gas oil distillation fractions

FT-Raman and photoacoustic (PA) infrared spectra of 12 distillation fractions derived from Syncrude light gas oil (LGO), which has a boiling range from 195 to 343 degrees C, were analyzed in detail in this study. In the fingerprint region (200-1800 cm(-1)) most of the information is obtained from the FT-Raman spectra, which display 36 bands that are assignable to various alkyl or aryl functional groups. Monocyclic, bicyclic and tricyclic aromatics in the 12 fractions were also characterized using Raman bands in this region. The corresponding section of the infrared spectra is much simpler, displaying a relatively small number of bands due to either aromatic or aliphatic CH(n) (n=1, 2 or 3) groups. The Cz.sbnd;H stretching region in both FT-Raman and PA infrared spectra of the LGO distillation fractions was curve-fitted according to procedures established in previous investigations of Syncrude samples with various boiling ranges. The PA spectra of the LGO fractions were also analyzed using an accepted integration strategy that requires no a priori assumptions with regard to the number of constituent bands or their shapes. The curve-fitting results show that the frequencies of the 11 Raman and eight infrared bands used to model the aliphatic ( approximately 2775-3000 cm(-1)) parts of the respective spectra decrease systematically as the median boiling points of the LGO fractions increase. These band positions are consistent with those determined in earlier studies of other distillation fractions. Both curve fitting and integration show that the abundance of CH(2) groups increases at the expense of CH(3) groups as the boiling points of the fractions increase within the LGO region.     

Fourier transform Raman spectroscopy of Syncrude Sweet Blend distillation fractions: the 200-1800 cm-1 region

The fingerprint (200-1800 cm(-1)) region in FT-Raman spectra of Syncrude Sweet Blend (SSB) and its three constituent distillation fractions (naphtha, light gas oil and heavy gas oil) was analyzed in detail in this study. Approximately 50 bands were observed and assigned to functional groups in saturated (alkanes) and unsaturated (aromatics) species. Characteristic bands for mono-, bi-, and tricyclic aromatics were identified and used to quantify these groups in SSB and the distillation fractions. Total aromatics content was determined using the carbon-carbon stretching bands in the 1600-cm(-1) region, and shown to agree with earlier results obtained from the C-H stretching region. The bands due to mono- and bicyclic aromatics permitted calculation of the relative abundances of these species with an accuracy equivalent to that obtained using NMR spectroscopy, a traditional method for measuring this quantity.     

Fluorescence rejection in Raman spectra of Syncrude Sweet Blend distillation fractions

Four techniques for the reduction or elimination of fluorescence from Raman spectra of Syncrude process samples were examined in this study. These methods are based on the retrieval of Raman bands from differential, or derivative spectra. Differential data were generated by subtracting similar spectra of a given sample obtained in three ways: (a) shifted detection utilizing an array detector and two successive spectrometer settings; (b) shifted excitation (dispersive Raman) where the two spectra are recorded using neighbouring laser lines and ordinary photon counting; (c) shifted excitation (FT-Raman) in which the laser frequency is changed in software before acquisition of the second spectrum. In addition to these differential techniques, derivative spectra were acquired directly with a dispersive Raman system by modulating the wavelength during scanning. These fluorescence rejection methods were applied to two groups of Syncrude Sweet Blend distillation fractions. For light gas oils (boiling range, 195-343 degrees C) the ratio of monocyclic and bicyclic aromatic species was determined and bands due to aliphatic CH(n) groups were characterized. Heavy gas oils (343-524 degrees C) yielded bands that allowed quantitation of monocyclic, bicyclic and total aromatic groups. Bands due to aliphatics were also identified for the heavy gas oils. These results constitute a significant advance compared to the information obtainable using conventional dispersive and FT-Raman spectroscopy for the analysis of hydrocarbon distillation fractions.     

Fourier transform Raman spectroscopy of Syncrude sweet blend distillation fractions derived from Athabasca bitumen

The C-H stretching region in FT-Raman spectra of Syncrude sweet blend (SSB) and three distillation fractions (naphtha, light gas oil and heavy gas oil) was analyzed in detail in this investigation. The frequencies and intensities of the 11 aliphatic and three aromatic C-H bands used to fit the spectrum of SSB were equal to the averages (weighted sums) of the corresponding quantities in the spectra of the fractions. The additivity of the spectra, thought to be a consequence of the large number of discrete compounds contained in each fraction, makes it possible to estimate the composition of other SSB samples using the spectra of the fractions reported in this work. In the aromatic C-H region, total intensities can be used to calculate the distribution of aromatics among the distillation fractions; these data also permit calculation of the fractional aromaticity (per cent aromatic carbon) for SSB and each fraction, with accuracies comparable to those obtained using NMR spectroscopy.     

Photoacoustic infrared spectroscopy of Syncrude post-extraction oil sand

Rapid- and step-scan photoacoustic (PA) infrared spectra of three fractions of a Syncrude post-extraction oil sand were analyzed in detail in this work. The rapid-scan spectra showed that the samples were comprised primarily of kaolinite, quartz, silica, siderite, and residual hydrocarbons, and that the proportions of these constituents were different for each fraction. Depth profiling of the three post-extraction oil sands was accomplished using both rapid- and step-scan PA infrared spectroscopy. The results confirmed that kaolinite is more abundant in the near-surface region, whereas quartz and hydrocarbons are concentrated at greater depths. The modulation frequency dependence of the PA intensities for all three fractions was consistent with a model in which the samples are thermally thick; in other words, the thermal diffusion length (roughly equal to the sampling depth) was less than the particle sizes of all three samples. The results of this study are consistent with published reports on the PA infrared spectra of fine tailings generated during bitumen extraction and the spectroscopic and thermophysical characterization of clay soils and an appropriate model clay.     

磷脂酰胆碱与牛血清白蛋白相互作用的FT-IR研究

利用傅立叶变换红外(FT-IR)和拉曼(FT-Raman)光谱研究了高浓度磷脂酰胆碱(PC)与牛血清白蛋白(BSA)的相互作用,及Eu3＋对该作用的影响.FT-IR结果显示,PC/BSA混合体系中二者的相互作用主要发生在PC头部极性基团,且这一作用随BSA含量的增加而增强,作用后蛋白质二级结构中α螺旋的比例有所增加. FT-Raman光谱说明PC与BSA的相互作用影响磷脂CH链的排列有序程度. PC/BSA/Eu3＋体系的红外光谱显示, Eu3＋与PC的磷氧键发生了强相互作用,并使蛋白α螺旋的比例进一步增加.     

Photoacoustic infrared spectroscopy and thermophysical properties of syncrude cokes

This paper presents and interprets photoacoustic (PA) infrared spectra and four different thermophysical properties (thermal conductivity, thermal diffusivity, volumetric specific heat and thermal effusivity) for four sets of hydrocarbon cokes. A total of 12 samples, with varying histories, were analyzed. These cokes are a by-product of the upgrading of bitumen to Syncrude Sweet Blend (a blend of hydrotreated components), and were obtained from several locations in the thermal cokers operated by Syncrude Canada Ltd. in Fort McMurray, Alberta, Canada. PA infrared spectroscopy provides detailed information on the amount and type of residual aromatic hydrocarbons in cokes; aliphatic hydrocarbons are sometimes detected in smaller quantities. Three of the thermophysical properties (thermal conductivity, diffusivity and effusivity) display systematic differences among the cokes. On the other hand, volumetric specific heat hardly varies, a phenomenon that accounts for the observed proportionality between thermal diffusivity and conductivity. Analogous relationships exist between thermal effusivity and both thermal conductivity and thermal diffusivity for these cokes. The magnitudes of these three thermophysical properties tend to increase as aromatics contents, determined by PA spectroscopy, decrease.This revised version was published online in November 2005 with corrections to the Cover Date.     

Fourier-transform Raman and infrared spectroscopic analysis of dipyrrinones and mesobilirubins

The Fourier-transform Raman (FT-Raman), infrared (FT-IR), and UV-visible absorption spectra of four dipyrrinones and two mesobilirubins have been investigated in the solid state and in CH2Cl2 solutions. A detailed spectral analysis, assignment and discussion of these spectra are presented. The bands at 1735-1738, 1691-1707 and 1359-1377 cm(-1) which were assigned to the stretching vibrations of the C-O-C and C-O-H and symmetric deformation of C-H bonds, respectively, can act as a marker to distinguish the compounds of this class. The striking differences between the spectra of the compounds suggest that mesobilirubin XIIIalpha is tending to adopt as ridge-tile conformation, rather than linear conformation.     

FT-IR, FT-Raman spectra and ab initio HF, DFT vibrational analysis of p-chlorobenzoic acid

The infrared, the Fourier transform infrared and Fourier transform Raman spectra of p-chlorobenzoic acid (p-CBA) has been recorded in the region 4000-600 cm(-1), 4000-400 cm(-1) and 4000-100 cm(-1), respectively. The optimized geometry, frequency and intensity of the vibrational bands of p-CBA were obtained by the ab initio HF and DFT (B3LYP) methods with complete relaxation in the potential energy surface using 6-311+G(d,p) basis set. The harmonic-vibrational frequencies were calculated and the scaled values have been compared with experimental FT-IR and FT-Raman spectra. The observed and the calculated frequencies are found to be in good agreement. The experimental spectra also coincide satisfactorily with those of theoretically constructed bar type spectrograms.     

Infrared absorption of CH3OSO detected with time-resolved Fourier-transform spectroscopy

A step-scan Fourier-transform spectrometer coupled with a multipass absorption cell was employed to detect temporally resolved infrared absorption spectra of CH(3)OSO produced upon irradiation of a flowing gaseous mixture of CH(3)OS(O)Cl in N(2) or CO(2) at 248 nm. Two intense transient features with origins near 1152 and 994 cm(-1) are assigned to syn-CH(3)OSO; the former is attributed to overlapping bands at 1154 ± 3 and 1151 ± 3 cm(-1), assigned to the S=O stretching mixed with CH(3) rocking (ν(8)) and the S=O stretching mixed with CH(3) wagging (ν(9)) modes, respectively, and the latter to the C-O stretching (ν(10)) mode at 994 ± 6 cm(-1). Two weak bands at 2991 ± 6 and 2956 ± 3 cm(-1) are assigned as the CH(3) antisymmetric stretching (ν(2)) and symmetric stretching (ν(3)) modes, respectively. Observed vibrational transition wavenumbers agree satisfactorily with those predicted with quantum-chemical calculations at level B3P86∕aug-cc-pVTZ. Based on rotational parameters predicted at that level, the simulated rotational contours of these bands agree satisfactorily with experimental results. The simulation indicates that the S=O stretching mode of anti-CH(3)OSO near 1164 cm(-1) likely makes a small contribution to the observed band near 1152 cm(-1). A simple kinetic model of self-reaction is employed to account for the decay of CH(3)OSO and yields a second-order rate coefficient k=(4 ± 2)×10(-10) cm(3)molecule(-1)s(-1).     

FT-Raman and infrared spectra and vibrational assignments for 3-chloro-4-methoxybenzaldehyde, as supported by ab initio, hybrid density functional theory and normal coordinate calculations

Fourier-transform laser Raman (3500-50 cm(-1)) and infrared (4000-400 cm(-1)) spectral measurements have been made for the solid 3-chloro-4-methoxybenzaldehyde. The electronic structure calculations -ab initio (RHF) and hybrid density functional methods (B3LYP and B3PW91) -- have been performed with 6-31G* and 6-311G* basis sets. Molecular electronic energies, equilibrium geometries, IR and Raman spectra have been computed. Potential energy distribution (PEDs) and normal mode analysis have also been performed. A complete assignment of the observed spectra has been proposed. Investigation of the relative orientation of the aldehydic oxygen and chlorine atom with respect to the methoxy group has shown that two forms, O-cis and O-trans exist, with O-trans form being more stable. The energy difference between O-cis and O-trans forms is 0.057 kcal/mol (21 cm(-1)) with B3LYP/6-31G*, which is less than the calculated torsional vibrational frequencies of the aldehyde and methoxy group. In the CH (O) aldehydic stretching region five observed bands are probably due to multiplet Fermi resonance. An infrared doublet near 1700 cm(-1) with nearly equal intensities has been ascribed to the Fermi resonance: the two bands at 1696 and 1679 cm(-1) arise due to the interaction between the CO stretching fundamental and a combination of O-CH(3) and CC stretching vibrations.     

Synthesis, DTA, IR and Raman spectra of penthylenediammonium hexachlorostannate NH3(CH2)5NH3SnCl6.

The Raman and IR spectra of NH3(CH2)5NH3SnCl6 have been measured at ambient temperature. It is shown that the cations in the compound assume a symmetry lower than C2v. Combination bands observed in the 2100-1800 cm(-1) region in the IR spectrum of NH3(CH2)5NH3SnCl6 indicate that the compound contains the C-NH3 grouping, the bands are discussed and their assignment are suggested. No evidence of existence of hydrogen bonding is found from the infrared spectrum in the region of 2800-3200 cm(-1); anions and cations are found not connected by hydrogen bonding and are therfore isolated. The Raman spectrum of anions can be interpreted in terms of disordered groups, not clearly showing the predicted splitting of bands.     

Nondestructive discrimination of ivories and prediction of their specific gravity by Fourier-transform Raman spectroscopy and chemometrics

Fourier-transform (FF) Raman spectroscopy and chemometrics were used for nondestructive analysis of ivories. The discrimination of five kinds of ivories, two subspecies of African elephant, mammoth, hippopotamus, and sperm whale, was investigated, and a calibration model for predicting their specific gravity was developed. FT-Raman spectra were measured in situ for them and chemometrics analyses were carried out for the 3050-350 cm(-1) region. The five kinds of ivories were clearly discriminated from each other on the scores plots of two or three principal components (PCs) obtained by principal component analysis (PCA). The loadings plot for PC 1 shows that the discrimination relies on the content ratio of organic collagenous protein and inorganic hydroxyapatite of ivories. The loadings plot for PC 2 shows that bands due to the CH3 and CH2 stretching modes of the protein also play a role in the discrimination. Using partial least squares regression (PLSR), we developed a calibration model that predicts the specific gravity of the ivories from the FT-Raman spectra. The correlation coefficient and root mean square error of cross validation (RMSECV) of this model were 0.980 and 0.024, respectively.     

Vibrational analysis of hydroxyacetone

In order to be able to fully understand the vibrational dynamics of monosaccharide sugars, we started with hydroxyacetone CH2OHCOCH3, and glycolaldehyde CH2OHCOH, which are among the smallest molecules that contain hydroxyl and carbonyl group on neighboring carbon atoms. This sterical configuration is characteristic for saccharides and determines their biochemical activity. In this work vibrational analysis of hydroxyacetone was undertaken by performing the normal coordinate analysis for glycolaldehyde first, and transferring these force constants to hydroxyacetone. The observed Raman and infrared bands for 90 wt.% solution of hydroxyacetone in water (acetol) were used as a first approximation for the bands of free hydroxyacetone. The number of observed Raman and infrared bands for acetol exceeds the number of calculated values for the most stable hydroxyacetone conformer with Cs symmetry, which suggests more than one conformer of hydroxyacetone in water solution. In particular, there are two bands both in infrared (1083 and 1057 cm(-1)) and in Raman spectrum (1086.5 and 1053 cm(-1)) that are assigned to the CO stretching mode and this is one of the indicators of several hydroxyacetone conformers in the solution. Additional information was obtained from low temperature Raman spectra: at 240 K a broad asymmetric band centered around 280 cm(-1) appears, suggesting a disorder in the orientation of hydroxyl groups. Glassy state forms at approximately 150K. The broad band at 80 cm(-1) is assigned to frozen torsions of hydroxymethyl groups.     

IR and FTMW-IR spectroscopy and vibrational relaxation pathways in the CH stretch region of CH3OH and CH3OD

Infrared spectra of jet-cooled CH(3)OD and CH(3)OH in the CH stretch region are observed by coherence-converted population transfer Fourier transform microwave-infrared (CCPT-FTMW-IR) spectroscopy (E torsional species only) and by slit-jet single resonance spectroscopy (both A and E torsional species, CH(3)OH only). Twagirayezu et al. reported the analysis of ν(3) symmetric CH stretch region (2750-2900 cm(-1); Twagirayezu et al. J. Phys. Chem. A 2010, 114, 6818), and the present work addresses the more complicated higher frequency region (2900-3020 cm(-1)) containing the two asymmetric CH stretches (ν(2) and ν(9)). The additional complications include a higher density of coupled states, more extensive mixing, and evidence for Coriolis as well as anharmonic coupling. The overall observed spectra contain 17 interacting vibrational bands for CH(3)OD and 28 for CH(3)OH. The sign and magnitude of the torsional tunneling splittings are deduced for three CH stretch fundamentals (ν(3), ν(2), ν(9)) of both molecules and are compared to a model calculation and to ab initio theory. The number and distribution of observed vibrational bands indicate that the CH stretch bright states couple first to doorway states that are binary combinations of bending modes. In the parts of the spectrum where doorway states are present, the observed density of coupled states is comparable to the total density of vibrational states in the molecule, but where there are no doorway states, only the CH stretch fundamentals are observed. Above 2900 cm(-1), the available doorway states are CH bending states, but below, the doorway states also involve OH bending. A time-dependent interpretation of the present FTMW-IR spectra indicates a fast (～200 fs) initial decay of the bright state followed by a second, slower redistribution (about 1-3 ps). The qualitative agreement of the present data with the time-dependent experiments of Iwaki and Dlott provides further support for the similarity of the fastest vibrational relaxation processes in the liquid and gas phases.     

FT-IR and FT-Raman spectral investigation, computed IR intensity and Raman activity analysis and frequency estimation analysis on 4-chloro-2-bromoacetophenone using HF and DFT calculations

In this work, the experimental and theoretical spectra of 4-chloro-2-bromoacetophenone (4C2BAP) are studied. FT-IR and FT-Raman spectra of title molecule have been recorded in the region 4000-100 cm(-1). The structural and spectroscopic data of the molecule in the ground state have been calculated by using Hartree-Fock and density functional method (B3LYP) with the 6-31G (d, p) and 6-311G (d, p) basis sets. The vibrational frequencies are calculated and scaled values are compared with the experimental FT-IR and FT-Raman spectra. The DFT (B3LYP/6-311G (d, p)) calculations are more reliable than the ab initio HF/6-311G (d, p) calculations for the vibrational study of 4C2BAP. The optimized geometric parameters (bond lengths and bond angles) are compared with experimental values of the molecule. The alteration of vibrational bands of the carbonyl and acetyl groups due to the presence of halogens (Cl and Br) in the base molecule is also investigated from their characteristic region of linked spectrum.     

Vibrational spectroscopy investigation using ab initio and density functional theory analysis on the structure of 2-amino-4,6-dimethoxypyrimidine

The FTIR and FT-Raman spectra of 2-amino-4,6-dimethoxypyrimidine (2A46DMP) has been recorded in the region 4000-400 cm(-1) and 3500-100 cm(-1), respectively. The optimized geometry, frequency and intensity of the vibrational bands of 2A46DMP were obtained by the ab initio and DFT levels of theory with complete relaxation in the potential energy surface using 6-31G(d,p) and 6-311G(d,p) basis sets. The harmonic vibrational frequencies were calculated and the scaled values have been compared with experimental FTIR and FT-Raman spectra. The observed and the calculated frequencies are found to be in good agreement. The experimental spectra also coincide satisfactorily with those of theoretically constructed bar type spectrograms.     

Molecular structure, vibrational, UV and NBO analysis of 4-chloro-7-nitrobenzofurazan by DFT calculations

In the present work, we reported a combined experimental and theoretical study on molecular structure, vibrational spectra and NBO analysis of 4-chloro-7-nitrobenzofurazan (NBD-Chloride). The FT-IR (400-4000 cm(-1)) and FT-Raman spectra (50-4000 cm(-1)) of NBD-Chloride were recorded. The molecular geometry, harmonic vibrational frequencies and bonding features of NBD-Chloride in the ground-state have been calculated by using the density functional B3LYP method with 6-311++G (d, p) as higher basis set. The energy and oscillator strength calculated by time-dependent density functional theory (TD-DFT) result in DMSO and CDCl3 solvents complements with each other. The calculated HOMO and LUMO energies show that charge transfer occurs within the molecule. Finally the calculation results were applied to simulate infrared and Raman spectra of the title compound which show good agreement with observed spectra.     

The investigation of chemical structure of coal macerals via transmitted-light FT-IR microspectroscopy

The Late Permian coals from South China are characterized by high content of the unique maceral "barkinite" and elemental hydrogen, typically produce high yields of tar, and exhibit significant oil-producing potential. "Barkinite" has been identified as suberinite for a long time, but now many Chinese workers have concluded that "barkinite" is not suberinite, rather it is a distinct maceral. The term "barkinite" was formally certified and named by the State Bureau of Technical Supervision of PR China in 1991, 1995, and 1999, however, it has not been recognized as a scientific term by international coal geologists and the ICCP. Transmitted-light FT-IR microspectroscopy and curve-fitting analysis were used to investigate the chemical structure of "barkinite"; at the same time, parallel studies were also carried out on vitrinite, fusinite, and sporinite. In comparison with other maceral types, the micro-FT-IR spectra of "barkinite" are characterized by very strong intensities of aliphatic CH(x) stretching vibrations at 3000-2800 cm(-1) and deformations at 1460-1450 cm(-1), less intense bands from aromatic CC ring stretching at 1610-1600 cm(-1) and aromatic CH out-of-plane deformations at 900-700 cm(-1). The aliphatic side-chains in the molecular structure of "barkinite" are longer and less branched. In addition, there also appear intense aliphatic ether COC and alcohol CO stretching bands at 1100-1000 cm(-1), notable aromatic CH stretching vibrations at 3050-3030 cm(-1), weak OH stretching bands of water in the 3600-3200 cm(-1) range, and rare acid CO group absorption at 1740-1700 cm(-1). Collectively the IR spectral characteristics indicate that "barkinite" is composed of great numbers of long chain aliphatics, a fewer of aromatics and rare of oxygenate components. The chemical structure of "barkinite" show that the high tar yields and the relatively high oil-producing potential of the Late Permian coals from South China are attributable to the high "barkinite" content in the Leping coals and the great numbers of long chain aliphatic substances contained in this maceral.     

FTIR, FT-Raman spectra and ab initio DFT vibrational analysis of 2,4-dichloro-6-nitrophenol

The FTIR and FT-Raman spectra of 2,4-dichloro-6-nitrophenol (2,4-DC6NP) has been recorded in the region 4000-400 cm(-1) and 3500-100 cm(-1), respectively. The optimized geometry, frequency and intensity of the vibrational bands of (2,4-DC6NP) were obtained by the ab initio and DFT levels of theory with complete relaxation in the potential energy surface using 6-31G(d,p) and 6-311+G(d,p) basis sets. The harmonic vibrational frequencies were calculated and the scaled values have been compared with experimental FTIR and FT-Raman spectra. The observed and the calculated frequencies are found to be in good agreement. The experimental spectra also coincide satisfactorily with those of theoretically constructed bar type spectrograms.