EQCM analysis of Bi oxidation mechanism on a Pt electrode

The electro-oxidation behaviours of bismuth (Bi) species adsorbed on a platinum (Pt) anode were investigated using an in situ electrochemical quartz crystal microbalance analysis in the measurement of cyclic voltammetry (CV) and electrochemical impedance spectroscopy under potentiostatic mode. In the CV of Bi modified Pt, there were four distinct features in the current–potential curves during an anodic scan: (i) the adsorption of water molecules in acidic media, (ii) the formation of Bi oxide, (iii) ionization of Bi oxide and (iv) partial desorption of Bi species. During a cathodic scan, the Bi modified Pt surface recovered to its original state via the reduction of Bi oxide and re-deposition of Bi ion. Surface mass data with electrical charge change and impedance measurements of Bi modified Pt supported the electrocatalytic oxidation of bismuth species as the responsible mechanism.     

Well-dispersed multi-walled carbon nanotube/polyaniline composite films

Multi-walled carbon nanotube (MWNT)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dispersed MWNTs. The results of transmission electron microscopy (TEM) show that aniline can be used to solve MWNTs via formation of donor–acceptor complexes. Scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI-coated MWNTs in these films facilitated improved electron and ion transfer relative to pure PANI films and this may be due to the strong interaction between MWNTs and PANI.     

Computational Modelling and Sustainable Synthesis of a Highly Selective Electrochemical MIP-Based Sensor for Citalopram Detection

A novel molecularly imprinted polymer (MIP) has been developed based on a simple and sustainable strategy for the selective determination of citalopram (CTL) using screen-printed carbon electrodes (SPCEs). The MIP layer was prepared by electrochemical in situ polymerization of the 3-amino-4 hydroxybenzoic acid (AHBA) functional monomer and CTL as a template molecule. To simulate the polymerization mixture and predict the most suitable ratio between the template and functional monomer, computational studies, namely molecular dynamics (MD) simulations, were carried out. During the experimental preparation process, essential parameters controlling the performance of the MIP sensor, including CTL:AHBA concentration, number of polymerization cycles, and square wave voltammetry (SWV) frequency were investigated and optimized. The electrochemical characteristics of the prepared MIP sensor were evaluated by both cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. Based on the optimal conditions, a linear electrochemical response of the sensor was obtained by SWV measurements from 0.1 to 1.25 µmol L⁻¹ with a limit of detection (LOD) of 0.162 µmol L⁻¹ (S/N = 3). Moreover, the MIP sensor revealed excellent CTL selectivity against very close analogues, as well as high imprinting factor of 22. Its applicability in spiked river water samples demonstrated its potential for adequate monitoring of CTL. This sensor offers a facile strategy to achieve portability while expressing a willingness to care for the environment.     

以马来松香丙烯酸乙二醇酯为交联剂的咖啡因分子印迹电化学传感器

以咖啡因为模板分子, 含菲环骨架的马来松香丙烯酸乙二醇酯为交联剂, 甲基丙烯酸为功能单体, 在玻碳电极表面以自由基热聚合的方式制备分子印迹聚合物敏感膜, 构建了测定咖啡因的新型分子印迹膜电化学传感器. 通过循环伏安法、 差分脉冲伏安法及电化学交流阻抗法研究了传感器对咖啡因的响应特性. 结果表明, 在最佳的实验条件下, 传感器的峰电流与咖啡因浓度在3.00×10^-3~2.73 mmol/L范围内呈现良好的线性关系, 检出限(S/N=3)为1.12×10^-4 mmol/L. 传感器具有良好的选择性和重现性. 将该传感器用于可口可乐饮料中咖啡因含量的测定, 平均回收率为98.7%.     

Nanopore membrane-based electrochemical immunoassay

Using nanotechnology in the immunoassay field, Lynntech has developed a nanopore-based sensor with electrochemical signal transduction for the detection of biologically relevant molecular targets. Antibodies of interest were immobilized on the inside wall of nanopores and the antibody–antigen interaction was monitored by measuring the ionic conductance through the nanopores. We have used electrochemical impedance spectroscopy to monitor the changes in the ionic conductance due to the antibody–antigen interaction. To aid the development of a portable, fast immunoassay instrument, we have selected specific impedance frequency values that are very sensitive to the ionic conductance changes. Biomarkers of prostate cancer, prostate-specific antigen and hepsin, were successfully assayed by the nanopore membrane-based electrochemical immunoassay in both phosphate-buffered saline and plasma medium.     

Electrochemical impedance analysis of methanol oxidation on carbon nanotube-supported Pt and Pt-Ru nanoparticles

Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) are employed to investigate methanol oxidation reactions on single-walled carbon nanotube-supported platinum (Pt) and platinum–ruthenium (Pt-Ru) nanoparticles. EIS and CV measurements show consistent results: Pt catalyst supported on single-walled carbon nanotubes possesses higher catalytic activity for methanol oxidation than that on carbon black. Additionally, semicircles in the second quadrant of the Nyquist diagrams are observed for methanol oxidation on all types of catalytic nanoparticles when applying an electrical potential of 600 mV, which indicates the occurrence of negative resistance during electrocatalytic methanol oxidations. However, all impedance spectra show positive resistance at other electrode potentials (e.g., 300, 400, and 800 mV). Electrocatalytic characteristics of all catalysts are further analyzed by equivalent circuit simulations. We propose that intermediate coverage on the catalyst surface and subsequently the oscillation of nonlinear electrochemical methanol oxidations lead to the occurrence of negative resistance at 600 mV.     

Electrosynthesis of Molecularly Imprinted Poly‐o‐phenylenediamine on MWCNT Modified Electrode for Selective Determination of Meldonium

In this study, a molecularly imprinted polymer (MIP) was synthesized by electrochemical polymerization and used to construct an electrochemical sensor for determination of meldonium (MEL) selectively for the first time. The polymer film was generated by using o‐phenylenediamine (o‐PD) as a monomer on the surface of carboxylic acid functionalized multiwalled carbon nanotube (MWCNT) modified pencil rod electrode in the presence of MEL as a template. MEL imprinted (MEL‐imp) and non‐imprinted (N‐imp) polymer films and coated electrodes were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), profilometry, electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Voltammetric measurements were carried out in a ferrocyanide/ferricyanide redox probe solution for MEL‐imp and N‐imp electrodes in the presence and absence of template molecule. The decrease in peak current of redox probe was linear with the concentration of MEL in the range of 0.1–5 μg/mL and the limit of detection (3 s/b) was found to be 0.066 μg/mL under optimized experimental conditions. The proposed sensor was successfully applied for selective determination of MEL in human urine sample with long term stability and good reproducibility.     

Two-layered Au@Ag Bimetallic Nanocomposites-poly (L-Met) Platform for Highly Sensitive Chlorpheniramine Maleate Detection

The two-layered bimetallic Au@Ag and poly(L-methionine) (Au@Ag/p-L-met) sensor was newly developed for the electrochemical determination of chlorpheniramine maleate (CPM). After electropolymerization of L-met, bimetallic surfaces were prepared by electrodeposition of Au@Ag nanoparticles on the p-L-met/PGE. The surface characterization was carried out by scanning electron microscopy (SEM), Energy Dispersive X-ray spectroscopy (EDX), Cyclic Voltammetry (CV) and Electrochemical impedance spectroscopy (EIS). The sensor shows good electrocatalytic activity, high sensitivity, wide linear range (0.87–600.0 μM) and a low detection limit (0.26 μM) by using Differential pulse voltammetry (DPV). The sensor was used to determine CPM in pharmaceutical samples with satisfactory results.     

基于纳米金的分子印迹传感器检测果蔬中的氧化乐果和乐果

以甲基丙烯酸为功能单体,氧化乐果为印迹分子,构建了一种可用于检测果蔬中氧化乐果和乐果的分子印迹传感器.在金电极上电沉积金纳米粒子,然后将修饰电极浸入10 mL含有氧化乐果和甲基丙烯酸的聚合物溶液中进行9次循环电聚合(-0.3～0.3 V),无水甲醇/乙酸洗涤除去模板分子.循环伏安法和电化学阻抗谱表征传感器,差分脉冲伏安...     

Electrochemical impedance studies of the undoping process of platinum phthalocyanine charge transfer microcrystals

Platinum phthalocyanine (PtPc) microcrystal films undergo three successive electrochemical oxidations. Each of these processes is associated with anion insertion or doping. The reverse process of anion insertion, undoping, has been investigated using electrochemical impedance spectroscopy and in-situ UV–vis spectroscopy. The impedance theory of conductive polymer films developed by Vorotyntsev et al. is applicable to this process. The kinetics of the undoping process depend upon the previous oxidative treatment, and thus the doping level. Three different states of the film can be demarcated, depending on the degree of oxidation (and thus the degree of doping) of the PtPc film. These are called the lightly doped, the conductive and the over-doped state, respectively. For lightly doped films, the film conductivity, the redox capacitance, the diffusion coefficient for charge transport and the rate of electrochemical reaction all decrease with decreasing potential. The film conductivity depends upon the concentration of free charge carriers. For the more highly doped conductive film, all of the above parameters are greatly enhanced, and the electrochemical reaction is accelerated and proceeds at a very high rate. The potential dependence of the redox capacitance and the diffusion coefficient depends on the type of anion. During undoping at 0 V, unusually high diffusion coefficients with a magnitude of order 10⁻² cm² s⁻¹ are observed and are attributed to the strong interactions between the electronic and ionic carriers during the phase transformation. For the over-doped film, undoping leads to an increase in the film conductivity and electrochemical reaction rate. The potential dependence of the redox capacitance and diffusion coefficients for charge transport implies strong interactions within the film. Hypsochromic shifts in UV–vis spectra with decreasing potential indicate conformational relaxation during the undoping process. SEM investigation confirms that the doped film swells during the de-doping process.     

Development of an Electrochemical Sensor for Selective Determination of Dopamine Based on Molecularly Imprinted Poly(p-aminothiophenol) Polymeric Film

In this study, a molecularly imprinted electrochemical sensor (MIP/DA) was investigated for selective and sensitive determination of dopamine (DA) by electrochemical polymerization of p-aminothiophenol in the presence of DA on gold electrode. According to electrochemical behaviour of the sensor, gained through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), MIP/DA sensor showed distinctive electron transfer characteristics in comparison to the non-imprinted (NIP/DA) sensor. Besides the MIP/DA sensor showed high selectivity for dopamine through its analyte specific cavities. The sensor had a broad working range of 5.0×10⁻⁸–2.0×10⁻⁷ M with a limit of detection (LOD) of 1.8×10⁻⁸ M and the developed sensor was successfully applied for determination of dopamine in pharmaceutical samples.     

A microgap impedance sensor for the determination of trace water in organic solvents

A microgap impedance sensor with a 50 μm gap was developed for the determination of trace water in organic solvents by coating poly(dimethyldiallylammonium chloride) (PDMDAAC) and ferricyanide/ferrocyanide composite materials on indium tin oxide (ITO). The electrochemical properties of the composite materials were investigated with cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). We observed that the impedance response of the sensor depended on the concentration of trace water in the organic solvents. Under optimized conditions, the linear range for the determination of trace water was 0-0.06% for chloroform (CHCl(3)), 0-0.10% for acetone (CH(3)COCH(3)), 0-0.12% for tetrahydrofuran (THF), and 0-0.10% for acetonitrile (CH(3)CN), and the detection limits were 0.65, 1.54, 0.61, and 1.72 ppm, respectively. The results obtained from the impedance sensors were comparable to those obtained using the traditional Karl Fischer method.     

Electrochemical Polymerization of Aniline in Polyamide and Polyvinyl Alcohol Matrices

The electrochemical polymerization of aniline was studied in polymer matrices (polyamid-12 and polyvinyl alcohol) on an electrode in the potential cycling mode from –0.2 to +0.8 V vs. SCE. The indices of this process such as the potentials and currents of the polyaniline redox peaks, polymerization rate, and properties of the conducting composite formed depend on the nature of the matrix polymer and are a function of the extent of interaction of this matrix polymer with aniline and polyaniline.     

纳米氧化铜修饰的苯巴比妥分子印迹传感器的制备及其电化学性能

为了改善分子印迹传感器的灵敏度,在四丁基高氯酸铵的支持电解质溶液中,以甲基丙烯酸为功能单体,马来松香丙烯酸乙二醇酯为交联剂在纳米氧化铜修饰过的玻碳电极上电聚合了一种苯巴比妥(PB)识别性能的分子印迹传感膜.采用循环伏安(CV)法、差分脉冲伏安(DPV)法及交流阻抗(EIS)法对这种纳米氧化铜修饰过的印迹及非印迹电极的电化学性能进行了研究,结果显示纳米氧化铜修饰过的印迹及非印迹电极的电化学性能完全不同.X射线衍射(XRD)证实纳米粒子为氧化铜.采用扫描电镜(SEM)对纳米氧化铜修饰过的印迹传感器的形貌进行分析,发现纳米氧化铜分散在电极表面,改善了修饰印迹传感器的识别点.差分脉冲伏安法(DPV)表明苯巴比妥的浓度在1.0×10-8-1.8×10-4mol·L-1范围内呈现良好的线性关系(线性相关系数R=0.9994);检出限2.3×10-9mol·L-1(信噪比(S/N)=3).研究结果表明纳米氧化铜修饰过的印迹传感器具有较高灵敏度及选择性.此印迹传感器能用于实际样品中苯巴比妥的检测,加标回收率在95.0%-102.5%.     

LiPF_6/三氟乙酰胺室温熔盐的制备及在碳-碳电容器中的性能

利用LiPF6和三氟乙酰胺为前驱物,制备了低共熔温度约为-62℃的室温熔盐,并测试了该熔盐作为碳-碳电化学电容器(EDLCs)电解液时的性能。其中,使用差示扫描量热法(DSC)和红外光谱法(FTIR)分析了不同LiPF6和三氟乙酰胺配比熔盐的热稳定性,拟制了该二元组分的共熔相图,认为LiPF6和三氟乙酰胺极性基团间的氢键作用促成了室温熔盐的形成。循环伏安(CV)、交流阻抗(EIS)和电导等测定结果表明,所制备的LiPF6/三氟乙酰胺电解液的室温电导率为1.30mS/cm,电化学窗口大于5.6V,大于60℃的使用温度,作为电解液可满足碳-碳EDLCs的使用要求。     

The Electrochemical Behavior of a N‐containing Calix[4]arene Derivative

The electrochemical behavior of 5,11,17,23‐Tetrakis‐dimethylaminomethylcalix[4]arene (DCA) has been investigated by cyclic voltammetry (CV). The results show that there is an irreversible electrochemical oxidative wave with peak potential of 1.35 V in chloroform at a glassy carbon electrode. The kinetic parameters of the andic wave, such as α, n and k_s, were discussed. In addition, a new pair of quasi‐reversible redox peaks with peak potentials of 0.72 V and 0.94 V was found. It can result in DCA electrodeposition at the electrode surface. This film modified electrode was characterized by CV and electrochemical impedance spectroscopy (EIS). Moreover, the possible mechanism of electrodeposition was also discussed     

Electroreductive polymerization of trans-[RuCl 2(vpy) 4] on Nd-Fe-B magnets: electrochemical impedance spectroscopy interpretation, Raman spectroscopy, X-ray photoelectron spectroscopy and scanning electron microscopy analysis

The electropolymerization of trans-[RuCl₂(vpy)₄] (vpy=4-vinylpyridine) monomer on Nd-Fe-B magnets was studied by electrochemical impedance spectroscopy (EIS). Impedance diagrams obtained during the polymerization process were used to monitor film formation. The EIS results gave insight into the electrochemical phenomena occurring at the magnet surface as the polymerization process progressed. The film structure and morphology were also studied by X-ray photoelectron spectroscopy, scanning electron microscopy and Raman spectroscopy. The Raman spectroscopy results showed that the polymerization takes place at the vinyl groups of the monomer and also that the redox polymer structure is very similar to that of the monomer. The ratio of the intensity of the XPS peaks for fluorine (from the electrolyte PF₆ ^–) and ruthenium present in the film showed that the polymer on Nd-Fe-B contained an equal proportion of Ru²⁺ and Ru³⁺, indicating that part of the film is positively charged, i.e. {[RuCl₂(vpy)₄]⁺} _n .     

Solid polymer electrochemical capacitors using heteropoly acid electrolytes

An electrochemical capacitor utilizing a polyvinyl alcohol (PVA) and H₄SiW₁₂O₄₀ (SiWA) solid polymer electrolyte was developed. The electrolyte was deposited via precursor solution coating followed by thermal pressing and exhibited an ionic conductivity of 0.01 S/cm. The electrolyte has also shown good stability and cycle life. The performance of the solid polymer electrolyte-based capacitor was characterized using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), and was compared to a similar capacitor with an aqueous electrolyte.     

Synthesis and characterization of p-toluenesulfonate incorporated poly(3,4-ethylenedioxythiophene)

Poly(3,4-ethylenedioxythiophene) (PEDOT), a conducting polymer, was electrochemically synthesized with p-toluenesulfonate (TSNa) as a dopant on gold surface. The electrochemical properties of the polymer were studied by impedance spectroscopy and cyclic voltammetry (CV). It was found that the impedance magnitude of the electrode significantly decreased over a wide range of frequency from 10⁰ to 10⁴ Hz after the polymer deposition. The CV demonstrated enhanced reversibility of the PEDOT film. The surface morphology was investigated by scanning electronic microscope (SEM) and atomic force microscope (AFM). Due to the effect of TSNa structure, nano-fungus was observed. Polymerization time was optimized and 30 min deposition resulted in the highest charge capacity, showing the highest electroactive surface area, possibly due to its porous structured polymer. Moreover, the high specific surface area could be favorable for cell attachment. The stability of PEDOT in glutathione (GSH), a common biologically relevant reducing agent, was studied with polypyrrole (PPy) as a baseline. It showed that the former had much better stability than the latter and it could be an excellent candidate for potential applications of in vivo neural devices.     

Internal surface polarity of regenerated cellulose gel depends on the species used as coagulant

We report the development of a new selective and specific electrochemical biosensor for bacterial lipolysaccharide (LPS). An electrode interface was constructed using a l-cysteine-gold nanoparticle (AuNpCys) composite to be immobilized by electrostatic interaction in the network of a poly(vinyl chloride-vinyl acetate maleic acid) (PVM) layer on a gold bare electrode. The impedimetric biosensor is fabricated by self-assembled CramoLL lectin on the PVM-AuNpCys-modified gold electrode through electrostatic interaction. CramoLL is used as the recognition interface. AFM images showed that LPS was specifically recognized on the PVM-AuNpCys-CramoLL system surface. The measurements of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) showed that the electrochemical response of a redox probe system (K(4)[Fe(CN)(6)](4-)/K(3)[Fe(CN)(6)](3-)) were blocked, due to the procedures of modified electrode with PVM-AuNpCys-CramoLL. In the majority of the experiments the lectin retained its activity as observed through its interaction with LPS from Escherichia coli, Serratia marcescens, Salmonella enterica and Klebsiella pneumoniae. The results are expressed in terms of the charge transfer resistance and current peak anodic using the EIS and CV techniques for the development of a biosensor for contamination by endotoxins. A new type of sensor for selective discrimination of LPS types with a high sensitivity has been obtained.