Formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys

The formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys were investigated by X-ray photoelectron spectroscopy (XPS) and by adsorption of CO probe molecules, which was characterized by temperature-programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS). The PdAg/Pd(1 1 1) surface alloys were prepared by annealing (partly) Ag film covered Pd(1 1 1) surfaces, where the Ag films were deposited at room temperature. Surface alloy formation leads to a modification of the electronic properties, evidenced by core-level shifts (CLSs) of both the Pd(3d) and Ag(3d) signal, with the extent of the CLSs depending on both initial Ag coverage and annealing temperature. The role of Ag pre-coverage and annealing temperature on surface alloy formation is elucidated. For a monolayer Ag covered Pd(1 1 1) surface, surface alloy formation starts at ∼450 K, and the resulting surface alloy is stable upon annealing at temperatures between 600 and 800 K. CO TPD and HREELS measurements demonstrate that at 120 K CO is exclusively adsorbed on Pd surface atoms/Pd sites of the bimetallic surfaces, and that the CO adsorption behavior is dominated by geometric ensemble effects, with adsorption on threefold hollow Pd₃ sites being more stable than on Pd₂ bridge sites and finally Pd₁ a-top sites.     

Infrared reflection absorption spectral study for CO adsorption on Pd/Pt(1 1 1) bimetallic surfaces

Infrared reflection absorption spectroscopy (IRRAS) was used to investigate carbon monoxide (CO) adsorption on 0.15 nm-thick-0.6 nm-thick Pd-deposited Pt(1 1 1) bimetallic surfaces: Pd_x/Pt(1 1 1) (where x is the Pd thickness in nanometers) fabricated using molecular beam epitaxial method at substrate temperatures of 343 K, 473 K, and 673 K. Reflection high-energy electron diffraction (RHEED) measurements for Pd_0.15-0.6 nm/Pt(1 1 1) surfaces fabricated at 343 K showed that Pd grows epitaxially on a clean Pt(1 1 1), having an almost identical lattice constant of Pt(1 1 1). The 1.0 L CO exposure to the clean Pt(1 1 1) at room temperature yielded linearly bonded and bridge-bonded CO-Pt bands at 2093 and 1855 cm⁻¹. The CO-Pt band intensities for the CO-exposed Pd_x/Pt(1 1 1) surfaces decreased with increasing Pd thickness. For Pd_0.3 nm/Pt(1 1 1) deposited at 343 K, the 1933 cm⁻¹ band caused by bridge-bonded CO-Pd enhanced the spectral intensity. The linear-bonded CO-Pt band (2090 cm⁻¹) almost disappeared and the bridge-bonded CO-Pd band dominated the spectra for Pd_0.6 nm/Pt(1 1 1). With increasing substrate temperature during the Pd depositions, the relative band intensities of the CO-Pt/CO-Pd increased. For the Pd_0.3 nm/Pt(1 1 1) deposited at 673 K, the linear-bonded CO-Pt and bridge-bonded CO-Pd bands are located respectively at 2071 and 1928 cm⁻¹. The temperature-programmed desorption (TPD) spectrum for the 673 K-deposited Pd_0.3 nm/Pt(1 1 1) showed that a desorption signal for the adsorbed CO on the Pt sites decreased in intensity and shifted ca. 20 K to a lower temperature than those for the clean Pt(1 1 1). We discuss the CO adsorption behavior on well-defined Pd-deposited Pt(1 1 1) bimetallic surfaces.     

Infrared reflection absorption study of carbon monoxide adsorption on Pd/Cu(1 1 1)

Pd-Cu bimetallic surfaces formed through a vacuum-deposition of Pd on Cu(1 1 1) have been discussed on the basis of carbon monoxide (CO) adsorption: CO is used as a surface probe and infrared reflection absorption (IRRAS) spectra are recorded for the CO-adsorbed surfaces. Low energy electron diffraction (LEED) patterns for the bimetallic surfaces reveal six-fold symmetry even after the deposition of 0.6 nm. The lattice spacings estimated by the separations of reflection high-energy electron diffraction (RHEED) streaks increase with increasing Pd thickness. Room-temperature CO exposures to the bimetallic surfaces formed by the Pd depositions less than 0.3 nm thickness generate the IRRAS bands due to the three-fold-hollow-, bridge- and linear-bonded CO to Pd atoms. In particular, on the 0.1 nm-thick Pd surface, the linear-bonded CO band becomes apparent at an earlier stage of the exposure. In contrast, the bridge-bonded CO band dominates the IRRAS spectra for CO adsorption on the 0.6 nm-thick Pd surface, at which the lattice spacing corresponds to that of Pd(1 1 1). A 90 K-CO exposure to the 0.1 nm-thick Pd surface leads to the IRRAS bands caused not only by CO-Pd but also by CO-Cu, while the Cu-related band is almost absent from the spectra for the 0.3 nm-thick Pd surface. The results clearly reveal that local atomic structures of the outermost bimetallic surface can be discussed by the IRRAS spectra for the probe molecule.     

Adsorption of water on TiN (1 0 0), (1 1 0) and (1 1 1) surfaces: A first-principles study

We use first-principles density functional theory-based calculations in the analysis of the interaction of H₂O with (1 0 0), (1 1 0) and (1 1 1) surfaces of TiN, and develop understanding in terms of surface energies, polarity of the surface and chemistry of the cation, through comparison with H₂O adsorption on ZrN. While water molecule physisorbs preferentially at Ti site of (1 0 0) and (1 1 1) surfaces, it adsorbs dissociatively on (1 1 0) surface of TiN with binding stronger than almost 1.32 eV/molecule. Our analysis reveals the following general trends: (a) surfaces with higher energies typically lead to stronger adsorption, (b) dissociative adsorption of H₂O necessarily occurs on a charge neutral high energy surface and (c) lower symmetry of the (1 1 0) plane results in many configurations of comparable stability, as opposed to the higher symmetry (1 0 0) and (1 1 1) surfaces, which also consistently explain the results of H₂O adsorption on MgO available in literature. Finally, weaker adsorption of H₂O on TiN than on ZrN can be rationalized in terms of greater chemical stability of Ti arising from its ability to be in mixed valence.     

Adsorption of carbon monoxide on Pd(3 1 1) and (2 1 1) surfaces

Adsorption of carbon monoxide on Pd(3 1 1) and (2 1 1) stepped surfaces has been investigated by the extended London-Eyring-Polyani-Sato (LEPS) method constructed using a 5-parameter Morse potential. The calculated results show that there exist common characteristics of CO adsorption on the two surfaces. At low coverage, CO occupies threefold hollow site of the (1 1 1) terrace and is tilted with respect to the surface normal. Among the threefold hollow sites on the (1 1 1) terrace, the nearer the site is to the step, the greater is the influence of the step. The twofold bridge site on the (1 0 0) step is also a stable adsorption site at high coverage. Because of the different lengths of the (1 1 1) terraces, the (3 1 1) and (2 1 1) stepped surfaces have different characteristics. A number of new sites are exposed on the boundary regions, including the fourfold hollow site (H₄) of the (3 1 1) surface and the fivefold hollow site (H₅) of the (2 1 1) surface. At high coverage, CO resides in the H₅ site of the (2 1 1) surface, but the H₄ site of the (3 1 1) surface is not a stable adsorption site. This study further shows that the on-top site on the (1 0 0) step of Pd(3 1 1) is a stable adsorption site, but the same type of site on Pd(2 1 1) is not.     

Theoretical studies on the adsorption and decomposition of H2O on Pd(1 1 1) surface

To provide information about the chemistry of water on Pd surfaces, we performed density functional slab model studies on water adsorption and decomposition at Pd(1 1 1) surface. We located transition states of a series of elementary steps and calculated activation energies and rate constants with and without quantum tunneling effect included. Water was found to weakly bind to the Pd surface. Co-adsorbed species OH and O that are derivable from H₂O stabilize the adsorbed water molecules via formation of hydrogen bonds. On the clean surface, the favorable sites are top and bridge for H₂O and OH, respectively. Calculated kinetic parameters indicate that dehydrogenation of water is unlikely on the clean regular Pd(1 1 1) surface. The barrier for the hydrogen abstraction of H₂O at the OH covered surface is approximately 0.2-0.3 eV higher than the value at the clean surface. Similar trend is computed for the hydroxyl group dissociation at H₂O or O covered surfaces. In contrast, the O-H bond breaking of water on oxygen covered Pd surfaces, H₂O_ad + O_ad → 2OH_ad, is predicted to be likely with a barrier of ∼0.3 eV. The reverse reaction, 2OH_ad → H₂O_ad + O_ad, is also found to be very feasible with a barrier of ∼0.1 eV. These results show that on oxygen-covered surfaces production of hydroxyl species is highly likely, supporting previous experimental findings.     

Density-functional study of the CO chemisorption on bimetallic Pd–Sn(1 1 0) surfaces

We study the ordered PdSn c(2 × 2), (2 × 1), and PdSn₂ (3 × 1) overlayers deposited on Pd(1 1 0) by using first-principles density-functional calculations. It appears that the two PdSn structures are almost degenerate in the energy. Pd–Sn surfaces we consider do not display the marked buckling with Sn atoms displaced towards vacuum that is common for Pt–Sn surfaces. Low-coverage CO chemisorption at these overlayers and on analogous surface structures on Pd₃Sn is considered. It is shown that inclusion of an empirical correction to the CO adsorption energy changes the stable adsorption site from the long-bridge to the top one in most cases. The adsorption energy decreases with the number of Sn atoms in the vicinity of the adsorption site, and this property correlates well with the position of the centre of gravity of the local Pd d-electron band, and also with the variation of the local density of d-electron states at the Fermi level. The centre-of-gravity value is used to assess the core-level shifts for Pd atoms in various geometries. Most of the calculated data compare rather well with the recent measurements on Pd–Sn overlayers at Pd(1 1 0) as well as with other data on related bimetallic systems.     

First-principles calculations of hydrogen molecule adsorption on Ti (0 0 0 1)-(2 × 1) surface

Adsorption of H₂ molecule on the Ti (0 0 0 1)-(2 × 1) surface was studied by density functional theory with generalized gradient approximation (GGA). The parallel and vertical absorption cases were investigated in detail by adsorption energy and electronic structure analysis, we obtained three stable configurations of FCC-FCC (the two H atoms adsorption on the two adjacent fcc sites of Ti (0 0 0 1) surface, respectively), HCP-HCP (the two H atoms adsorption on the two adjacent hcp sites of Ti (0 0 0 1) surface, respectively) and FCC-HCP (the one H atom adsorption on the fcc site and the other adsorption on the near hcp site) based on the six different parallel adsorption sites after the H₂ molecule dissociates. However, all the end configurations of four vertical adsorption sites were unstable, H₂ molecule was very easy to desorb from Ti surface. The H-H bond breaking and Ti-H bond forming result from the H₂ molecule dissociation. H-H bond breaking length ranges from 1.9 Å to 2.3 Å for different adsorption configurations due to the strong Ti-H bond forming. The H₂ dissociative approach and the end stable configurations formation in parallel adsorption processes are attributed to the quantum mechanics steering effects.     

First principles studies of a Xe atom adsorbed on Nb(1 1 0) surface

We study adsorption sites of a single Xe adatom on Nb(1 1 0) surface using a density functional theory approach: the on-top site is the most favorable position for adsorption. We compare the binding features of the present study to earlier studies of a Xe adatom on close-packed (1 1 1) surfaces of face-centered cubic metals. The different features are attributed through a microscopic picture to the less than half filled d-states in Nb.     

Pd adsorption on Si(1 1 3) surface: STM and XPS study

Pd-induced surface structures on Si(1 1 3) have been studied by scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS). In the initial process of the Pd adsorption below 0.10 ML, Pd silicide (Pd₂Si) clusters are observed to form randomly on the surface. By increasing the Pd coverage to 0.10 ML, the clusters cover the entire surface, and an amorphous layer is formed. After annealing the Si(1 1 3)-Pd surface at 600 °C, various types of islands and chain protrusions appears. The agglomeration, coalescence and crystallization of these islands are observed by using high temperature (HT-) STM. It is also found by XPS that the islands correspond to Pd₂Si structure. On the basis of these results, evolution of Pd-induced structures at high temperatures is in detail discussed.     

Structural evolution of sulfur overlayers on Pd(1 1 1)

Low energy ion scattering spectroscopy (LEISS) has been used to characterize the evolution of ordered structures of S on the Pd(1 1 1) surface during annealing. During exposure of the Pd(1 1 1) surface to 0.7 L H₂S at 300 K—conditions that produce the S(√3 × √3)R30 overlayer—the intensity of the Pd LEIS signal decreases and a feature assigned to adsorbed S appears as the adsorbed layer forms. When the surface is held at 300 K after exposure to H₂S is stopped, the LEIS Pd intensity partially recovers and the S signal weakens, presumably as surface S atoms assume their equilibrium positions in the S(√3 × √3)R30 overlayer. Subsequent annealing of the S(√3 × √3)R30 structure at 700 K causes it to convert into a S(√7 × √7)R19 overlayer, whose LEIS spectrum is identical to that of clean Pd(1 1 1). The absence of LEIS evidence for S atoms at the exposed surface of the S(√7 × √7)R19 overlayer is at odds with published models of a mixed Pd-S top layer. Despite the similarity of the LEIS spectra of Pd(1 1 1) and Pd(1 1 1)-S(√7 × √7)R19, their activities for dissociative hydrogen adsorption are very different—the former readily adsorbs hydrogen at 100 K, while the latter does not—suggesting that S exerts its influence on surface chemistry from subsurface locations.     

The electronic structure and reactivity of the oxygen-modified Mo2C(0 0 0 1) surface

Oxygen adsorption on Mo₂C(0 0 0 1) has been investigated with angle-resolved photoemission spectroscopy (ARPES). When the surface is reacted with O₂, the O 2p-induced states are formed at 4.1 and 5.3 eV at the point. The emissions around the Fermi level are also intensified by oxygen adsorption, which is due to the formation of a partially filled state. It is found that the reactivity of the surface toward H₂O adsorption is much enhanced by pre-adsorption of oxygen. The reactivity is found to be maximized at θ_O ∼ 0.2.     

O2 dissociation on Pd(2 1 1) and Cu(2 1 1) surfaces

We have performed ab initio Density Functional Theory (DFT) based calculations to observe the reactivity of the Pd(2 1 1) and Cu(2 1 1) surfaces towards O₂. In order to properly address the adsorption dynamics, the static potential energy surface calculations have been complemented with first principles molecular dynamics calculations, which reveal interesting steering effects that complicate the dissociation dynamics. We have found that on both surfaces the step microfacets are very reactive and the dissociation of the O₂ molecule at room temperature occurs mostly on those sites.     

A DFT study of the chemisorption of methoxy on clean and low oxygen precovered Ru(0 0 0 1) surfaces

Adsorption of the methoxy radical on clean and on low oxygen precovered Ru(0 0 0 1) metallic surfaces has been studied by density-functional theory cluster calculations. Methoxy is predicted to be preferentially chemisorbed on both hollow sites (hcp and fcc) of such surfaces, and adopts an upright orientation (C_3ν local symmetry). Such prediction is supported by the good agreement found between the calculated vibrational frequencies and the experimentally observed RAIRS spectra. Regarding the charge transfer process between the adsorbate and the surface, our results suggest that the bonding is dominantly polar covalent which arises from a charge donation from the ruthenium surface to the radical, and the co-adsorbed electronegative oxygens deplete slightly the surface electron density. However, the major difference is not induced through much O-Ru bonding, but indirectly, by lowering the valence d-band center of the system. This results in a lower adsorption energy for methoxy than on the clean Ru(0 0 0 1) surface, in accordance with experimental data. Further, accordingly to the present calculations, the radical is expected to dissociate or desorb more easily on the modified surface but with no participation from the co-adsorbed oxygen atoms.     

First principles study of H2S adsorption and dissociation on Fe(1 1 0)

We report first principles density functional theory (DFT) results of H₂S and HS adsorption and dissociation on the Fe(1 1 0) surface. We investigate the site preference of H₂S, HS, and S on Fe(1 1 0). H₂S is found to weakly adsorb on either the short bridge (SB) or long bridge (LB) site of Fe(1 1 0), with a binding energy of no more than 0.50 eV. The diffusion barrier from the LB site to the SB site is found to be small (∼0.10 eV). By contrast to H₂S, HS is predicted to be strongly chemisorbed on Fe(1 1 0), with the S atom in the LB site and the HS bond oriented perpendicular to the surface. Isolated S atoms also are predicted to bind strongly to the LB sites of Fe(1 1 0), where the SB is found to be a transition state for S surface hopping between neighboring LB sites. The minimum energy paths for H₂S and HS dehydrogenation involve rotating an H atom towards a nearby surface Fe atom, with the S-H bonds breaking on the top of one Fe atom. The barrier to break the first S-H bond in H₂S is low at 0.10 eV, and breaking the second S-H bond is barrierless, suggesting deposition of S on Fe(1 1 0) via H₂S is kinetically and thermodynamically facile.     

Density functional and dynamics study of the dissociative adsorption of hydrogen on Mg (0 0 0 1) surface

A first principles study is performed to investigate the adsorption characteristics of hydrogen on magnesium surface. Substitutional and on-surface adsorption energies are calculated for Mg (0 0 0 1) surface alloyed with the selected elements. To further analyze the hydrogen-magnesium interaction, first principles molecular dynamics method is used which simulates the behavior of H₂ at the surface. Also, charge density differences of substitutionally doped surface configurations were illustrated. Accordingly, Mo and Ni are among the elements yielding lower adsorption energies, which are found to be −9.2626 and −5.2995 eV for substitutionally alloyed surfaces, respectively. In light of the dynamic calculations, Co as an alloying element is found to have a splitting effect on H₂ in 50 fs, where the first hydrogen atom is taken inside the Mg substrate right after the decomposition and the other after 1300 fs. An interesting remark is that, elements which acquire higher chances of adsorption are also seen to be competent at dissociating the hydrogen molecule. Furthermore, charge density distributions support the results of molecular dynamics simulations, by verifying the distinguished effects of most of the 3d and 4d transition metals.     

Core-level shifts at the Pt/W(1 1 0) monolayer bimetallic interface

We have measured W and Pt 4f_7/2 core-level photoemission spectra from interfaces formed by ultrathin Pt layers on W(1 1 0), completing our core-level measurements of W(1 1 0)-based bimetallic interfaces involving the group-10 metals Ni, Pd, and Pt. With increasing Pt coverage the sequence of W spectra can be described using three interfacial core-level peaks with binding-energy (BE) shifts (compared to the bulk) of −0.220 ± 0.015, −0.060 ± 0.015, and +0.110 ± 0.010 eV. We assign these features to 1D, 2D pseudomorphic (ps), and 2D closed-packed (cp) Pt phases, respectively. For ∼1 ps ML the Pt 4f_7/2 BE is 71.40 ± 0.02 eV, a shift of +0.46 ± 0.09 eV with respect to the BE of bulk Pt metal. The W 4f_7/2 core-level shifts induced by all three adsorbates are semiquantitatively described by the Born-Haber-cycle based partial-shift model of Nilsson et al. [39]. As with Ni/W(1 1 0), the difference in W 4f_7/2 binding energies between ps and cp Pt phases has a large structural contribution. The Pt 4f lineshape is consistent with a small density of states at the Fermi level, reflective of the Pt monolayer having noble-metal-like electronic structure.     

Carbon monoxide adsorption on the metastable fcc-Co/Cu(1 0 0) surface

The adsorption properties of CO on the epitaxial five-monolayer Co/Cu(1 0 0) system, where the Co overlayer has stabilized in the metastable fcc-phase, are reported. This system is known to exhibit metallic quantum well (MQW) states at energies 1 eV or greater above the Fermi level, which may influence CO adsorption. The CO/fcc-Co/Cu(1 0 0) system was explored with low energy electron diffraction (LEED), inverse photoemission (IPE), reflection-absorption infrared spectroscopy (RAIRS) and temperature programmed desorption (TPD). Upon CO adsorption, a new feature is observed in IPE at 4.4 eV above E_F and is interpreted as the CO 2π^∗ level. When adsorbed at room temperature, TPD exhibits a CO desorption peak at ∼355 K, while low temperature adsorption reveals additional binding configurations with TPD features at ∼220 K and ∼265 K. These TPD peak temperatures are correlated with different C-O stretch vibrational frequencies observed in the IR spectra. The adsorption properties of this surface are compared to those of the surfaces of single crystal hcp-Co, as well as other metastable thin film systems.     

Comparative DFT study of the adsorption of 1,3-butadiene, 1-butene and 2-cis/trans-butenes on the Pt(1 1 1) and Pd(1 1 1) surfaces

The interaction of 1,3-butadiene, 1-butene and 2-cis/trans-butenes on the Pt(1 1 1) and Pd(1 1 1) surfaces has been studied with density functional theory methods (DFT). The same most stable adsorption modes have been found on both metal surfaces with similar adsorption energies. For 1,3-butadiene the 1,2,3,4-tetra-σ adsorption structure is shown to be the most stable one, in competition with a 1,4-metallacycle-type mode, which is only less stable by 10-12 kJ mol⁻¹. On Pt(1 1 1) these total energy calculations were combined with simulations of the vibrational spectra. This confirms that the 1,2,3,4-tetra-σ adsorption is the most probable adsorption structure, but cannot exclude the 1,4-metallacycle as a minority species. Although similar in type and energy, the adsorption on the Pd(1 1 1) surface shows a markedly different geometry, with a smaller molecular distortion upon adsorption. The most stable adsorption structure for the butene isomers is the di-σ-mode. Similarly to the case of the 1,3-butadiene, the adsorption geometry is closer to the gas phase one on Pd than on Pt, hence explaining the different spectroscopic results, without the previously assumed requirement of a different binding mode. Moreover the present study has shown that the different selectivity observed on Pt(1 1 1) and Pd(1 1 1) for the hydrogenation reaction of butadiene cannot be satisfactory explained by the single comparison of the relative stabilities of 1,3-butadiene and 1-butene on these metals.     

Adsorption and dissociation of H2 on the Cu2O(1 1 1) surface: A density functional theory study

Interactions of atomic and molecular hydrogen with perfect and deficient Cu₂O(1 1 1) surfaces have been investigated by density functional theory. Different kinds of possible modes of H and H₂ adsorbed on the Cu₂O(1 1 1) surface and possible dissociation pathways were examined. The calculated results indicate that O_SUF, Cu_CUS and O_vacancy sites are the adsorption active centers for H adsorbed on the Cu₂O(1 1 1) surface, and for H₂ adsorption over perfect surface, Cu_CUS site is the most advantageous position with the side-on type of H₂. For H₂ adsorption over deficient surface, two adsorption models of H₂, H₂ adsorbing perpendicularly over O_vacancy site and H₂ lying flatly over singly-coordinate Cu-Cu short bridge, are typical of non-energy-barrier dissociative adsorption leading to one atomic H completely inserted into the crystal lattice and the other bounded to Cu_CUS atom, suggesting that the dissociative adsorption of H₂ is the main dissociation pathway of H₂ on the Cu₂O(1 1 1) surface. Our calculation result is consistent with that of the experimental observation. Therefore, Cu₂O(1 1 1) surface with oxygen vacancy exhibits a strong chemical reactivity towards the dissociation of H₂.