Stable MHz-repetition-rate passively Q-switched microchip laser frequency doubled by MgO:PPLN

We present an Nd³⁺:YVO₄ microchip laser that is passively Q-switched by a semiconductor saturable absorber mirror. The system generates 520 ps pulses at 1064 nm with 340 mW average output power at up to 2.3 MHz repetition rate. Single longitudinal and transverse mode operation with a peak-to-peak timing jitter less than 1 % is achieved. We discuss the influence of different setup parameters by using numerical simulations of the coupled rate equations and FEM simulations of the thermal management. The infrared light was frequency doubled in an MgO:PPLN crystal with up to 75 % conversion efficiency, which to our knowledge is the highest conversion efficiency that was ever achieved with passively Q-switched microchip lasers.     

Wavelength conversion based on degenerate-four-wave-mixing with continuous-wave pumping in silicon nanowire waveguide

We present a comprehensive numerical study on the all-optical wavelength conversion based on the degenerate four-wave-mixing with continuous-wave pumping in the silicon nanowire waveguide. It is well known that the conversion efficiency and the 3-dB bandwidth can be greatly affected by the phase-matching condition. Through proper design of the waveguide cross-section, its dispersion property can be adjusted to satisfy the phase-matching condition and therefore effective wavelength conversion can be achieved in a large wavelength range. Generally, the group velocity dispersion plays a dominant role in the wavelength conversion. However, the fourth-order dispersion takes an important effect on the wavelength conversion when the group velocity dispersion is near the zero-point. Furthermore, the conversion efficiency and the 3-dB bandwidth can also be affected by the interactive length and the initial pump power. Through the numerical simulation, the optimal values for the interactive length and the initial pump power, which are functions of the propagation loss, are obtained to realize the maximum conversion efficiency.     

一种直角转弯圆波导模式转换器设计

设计了一种尺寸紧凑并具有高功率容量的圆波导TE₁₁-TM₀₁模式转换器,结构呈直角转弯形状。该转换器利用传输TE₁₁模式的圆波导与其E面分支耦合进行模式转换,并在TM₀₁输出端口的反向传输短路面加入调配螺钉来拓宽频带。设计结果表明,转换器在工作频率12.7 GHz处的转换效率为99.6%,大于90%的带宽约20%,填充SF₆绝缘气体工作时可获得12 MW的功率容量。     

基于光纤四波混频波长转换和色散的慢光实验研究

对基于光纤四波混频（FWM）波长转换和色散的慢光实现进行了详细和系统的实验研究.首先,实验测定了高非线性光纤中FWM带宽约为40 nm,从而确定了慢光的可调谐带宽;接着,在普通单模光纤和色散补偿光纤（DCF）中针对500 MHz正弦信号和100 ps短脉冲信号分别实现了34和198 ns的脉冲延迟,在DCF中还实现了209 ns的脉冲提前.讨论了增大延迟量的方法,指出随着宽带FWM波长转换的实现和大色散光纤的应用有望获得微秒量级的大延迟量,从而为高性能光纤延迟线和全光缓存器等应用提供支持. 关键词： 慢光 四波混频 色散     

腔内带圆形空心波导的可调谐窄带脉冲染料激光器

本文报道了一种腔内带圆形空心波导和掠入射光栅的可调谐窄带脉冲染料激光器;实验结果表明:该激光系统能获得基横模、窄频带和高效率的激光输出。文中对系统设计机理也进行了分析。     

High power optically pumped far infrared lasers1

A review of operating principles and achieved characteristics of high power methyl fluoride lasers at λ = 496 μm is presented. In addition, a novel linear pumping scheme is described which allows direct amplification of radiation from a narrow bandwidth (<60 MHz) methyl flouride oscillator. A gain of 7. output power ∼ 10 kW and conversion efficiency of 0.15% have been observed. The method offers an avenue toward a MW-level narrow bandwidth source for use in plasma diagnostics.     

基于强激光辐照固体锡靶产生极紫外光源的实验研究

建立了一套利用高功率YAG激光器辐照固体锡靶产生高转换效率极紫外光 (extreme ultraviolet) 源的实验装置.利用建立的实验装置开展了极紫外光源的强度和转换效率与抽运激光强度关系的实验研究,发现极紫外光源的转换效率随抽运激光强度的变化具有饱和效应.实验发现：当抽运激光能量达到250mJ时,极紫外光源的转换效率最高,波长为13.5nm处0.27nm带宽范围内的极紫外光源的能量转换效率为1.6%,此时对应的激光强度为1.8×10¹¹W/cm². 关键词： 极紫外光 转换效率     

基于开口椭圆环的高效超宽带极化旋转超表面

电磁波的极化态在信号传输和灵敏度测量中有非常重要的应用价值. 本文设计、仿真并实验验证了微波频段基于开口椭圆环谐振器的极化旋转超表面. 理论上, 将多阶表面等离子谐振和高阻抗表面相结合, 解释了多谐振点、高效率极化旋转的物理机理. 数值上, 通过对结构参数的仿真分析, 给出了运用开口椭圆环结构设计多频段、超宽带高效极化旋转超表面的方法. 所设计和制作的超表面能够在相对带宽104.5%的频率范围内实现大于85%的极化旋转效率. 这些工作将为极化操控超表面的设计和应用提供重要帮助.     

High efficiency and broad bandwidth terahertz vortex beam generation based on ultra-thin transmission Pancharatnam–Berry metasurfaces

The terahertz(THz) vortex beam generators are designed and theoretically investigated based on single-layer ultra-thin transmission metasurfaces. Noncontinuous phase changes of metasurfaces are obtained by utilizing Pancharatnam–Berry phase elements, which possess different rotation angles and are arranged on two concentric rings centered on the origin.The circularly polarized incident THz beam could be turned into a cross-polarization transmission wave, and the orbital angular momentum(OAM) varies in value by lh. The l values change from ±1 to ±5, and the maximal cross-polarization conversion efficiency that could be achieved is 23%, which nearly reaches the theoretical limit of a single-layer structure.The frequency range of the designed vortex generator is from 1.2 THz to 1.9 THz, and the generated THz vortex beam could keep a high fidelity in the operating bandwidth. The propagation behavior of the emerged THz vortex beam is analyzed in detail. Our work offers a novel way of designing ultra-thin and single-layer vortex beam generators, which have low process complexity, high conversion efficiency and broad bandwidth.     

大角带宽高衍射效率体全息光栅的设计和制备

高性能体全息光栅是全息波导的重要耦合元件,角带宽小、平均衍射效率不高是制约体全息光栅性能的重要因素.以不对称倾斜记录为出发点,设计并制备了大角带宽高衍射效率的体全息光栅.首先讨论在横电模式光和横磁模式光下体全息光栅的记录参数与其衍射效率的关系,找到平均衍射效率较高的记录参数范围,随后进一步分析在此范围内的记录参数与体全...     

52 mJ narrow-bandwidth degenerated optical parametric system with a large-aperture periodically poled MgO:LiNbO3 device

We have demonstrated efficient, high-energy, narrow-spectral-bandwidth 2.128 microm pulse generation by use of periodically poled MgO:LiNbO3 devices with a 36 mm length and a 5 mm x 5 mm large aperture. A free-running degenerated optical parametric oscillator (OPO) pumped with a Q-switched 1.064 microm Nd:YAG laser exhibits a high slope efficiency of 75% and an optical-to-optical conversion efficiency of 70% with a broad spectral bandwidth (>100 nm). In a configuration with a spectrally narrowed master oscillator followed by a power amplifier, we have achieved an output pulse energy of 52 mJ with a spectral bandwidth of less than 2 nm at the degeneracy point. The total optical-to-optical conversion efficiency of the system reached 50%.     

Acoustooptic collinear TE-TM mode conversion in a two-layer Ti-indiffused and proton-exchanged waveguide structure in LiNbO3

Acoustooptic collinear TE-TM mode conversion was investigated in a two-layer Ti-indiffused and proton-exchanged waveguide structure in LiNbO₃. A very narrowband interaction of only 130 kHz (0.31 nm optical bandwidth) was achieved with about 25 mW acoustic power for 96% conversion efficiency. This structure is especially suitable for constructing novel-type acoustooptical gas sensors.     

Intense supercontinuum generation in the near-ultraviolet range from a 400-nm femtosecond laser filament array in fused silica

An intense supercontinuum(SC) in the near-ultraviolet range is generated from filamentation by focusing a 400-nm laser into fused silica with a microlens array(MLA). The spectrum of the SC is shown to be sensitive to the distance between the MLA and fused silica. In our optimal conditions, the near-ultraviolet SC can cover a range of 350-600 nm,where a bandwidth of approximately 55 nm above the 1μJ/nm spectral energy density and 20 nm bandwidth with tens ofμJ/nm are achieved. In addition, the energy conversion efficiency of the 400 nm laser for SC generation is further analyzed.A maximum conversion efficiency of 66% is obtained when the entrance face of fused silica is set around the focus of the MLA.     

High frequency atomic magnetometer by use of electromagnetically induced transparency

Atomic magnetometers have achieved magnetic sensitivities in the subfemtotesla regime. Their bandwidth is determined by the transverse spin relaxation rate, 1/T2, which also determines the magnetic sensitivity. It is theoretically demonstrated that by using an electromagnetically induced transparent probe beam in a pump-probe atomic magnetometer, it is possible to operate the latter at frequencies much higher than its bandwidth, maintaining a high signal-to-noise ratio.     

泵浦光的入射角对参量下转换的影响

利用参量下转换制备相关光子实现对各类探测器的量子效率的定标,是近年来兴起的新型定标技术。由于参量下转换的光子转换效率低,探测器输出信号信噪比小。采用短波激光器泵浦PPLN周期极化性晶体,可获得较大功率的参量光。分析了泵浦光在PPLN晶体端面的入射角对参量光的转换效率、空间分布、参量带宽及晶体周期的影响,并进行了数值模拟。分析发现当泵浦光正入射晶体端面时,参量光功率转换大,带宽小,发散角大;随着泵浦光入射角度逐渐增大,参量下转换的转换效率降低,相关光子的带宽变小,发散角变小且参量光的中心波长的空间位置会发生相对偏移。该研究结果可为相关光子探测、模拟探测器量子效率的高精度定标提供理论依据。     

Fields of apertured polychromatic laser beams with Gaussian and Hermite–Gaussian transverse modes

Starting from the Huygens–Fresnel diffraction integral, the field expressions of apertured polychromatic laser beams with Gaussian and Hermite–Gaussian transverse modes are derived. Influence of the bandwidth on the intensity distributions of the laser beams is analyzed. It is found that when the bandwidth increases, the amplitudes and numbers of the intensity spikes decrease and beam uniformity is improved in the near field and the width of transverse intensity distribution of the apertured beams decreases in the far field. Thus, the smoothing and narrowing effects can be achieved by increasing the bandwidth. Also, these effects are found in the laser beams with Hermite–Gaussian transverse modes as the bandwidth increases.     

A tunable,single mode,injection-locked flashlamp pumped dye laser

A tunable, very narrow bandwidth, flashpumped dye laser is described. Publse energies up to 50 mJ at a bandwidth of less than 30 MHz, and with a divergence of 0.4 mrad, are obtained. Spectral narrowing and tuning is achieved by injection locking of the pulsed laser to the radiation, of a tunable cw dye laser. The cavity is designed for single longitudinal and transverse mode operation, with a mode diameter large enough to fill the active medium. This work was supported in part by the Israel commission for Basic Research, and in part by a grant from the United States Israel Binational Science Foundation (BSF), Jerusalem, Israel.     

Quasi-phase-matched second-harmonic generation in a GaAs/AlAs superlattice waveguide by ion-implantation-induced intermixing

We report type I second-harmonic generation by use of first-order quasi-phase matching in a GaAs/AlAs symmetric superlattice structure with femtosecond fundamental pulses at 1.55 microm. Periodic spatial modulation of the bulklike second-order susceptibility chi(zxy)(2) was achieved with quantum-well intermixing for which the group III vacancies were created by As+-ion implantation. A narrow second-harmonic bandwidth of approximately 0.9 nm (FWHM) with an average power of approximately 1.5 microW was detected, corresponding to an internal conversion efficiency of approximately 0.06%, which was considerably limited by the spectral bandwidth of the fundamental.     

回旋速调管变周期TE01-TE11模式变换器

针对蛇形圆波导变换器尺寸大和带宽窄的不足,提出了变周期蛇形圆波导模式变换器,以实现TE01到TE11模式的高效率转换。根据耦合波方程,编制了优化计算程序,对工作于30.5 GHz、半径为16 mm的变周期以及传统蛇形变换器几何结构分别进行了优化计算,得到了可实现最高模式变换效率的几何参量。计算结果表明:传统结构变换器最优长度长达1 056.97 mm,转换效率98.1%,90%以上转换带宽也仅为3.3%;变周期变换器最优长度为769.53 mm,转换效率为99.3%,90%以上转换带宽为5.9%。变周期结构相对于传统结构的模式变换器具有尺寸小和带宽宽的明显优势。测试表明所提出的模式变换器具有良好的模式变换性能。     

Widely tunable 3.4 microm band difference frequency generation using apodized chi(2) grating

We achieved apodization in a quasi-phase-matched wavelength converter. The new design yields a large bandwidth and a flat phase-matching response with a high conversion efficiency. Using the method, we demonstrate widely tunable 3.4 microm band difference frequency generation in a LiNbO3 ridge waveguide.