Selective determination of caffeine and trigonelline in aqueous extract of green coffee beans by FT-MIR-ATR spectroscopy

A non-destructive, fast, simple and reliable Fourier transform mid-infrared attenuated total reflectance spectroscopy (FT-MIR-ATR) method for the selective determination of caffeine and trigonelline in the aqueous extract of green coffee beans was developed and validated. The calibration curves were linear in the range 2000 − 7000 mg/L for caffeine and trigonelline with R² ≥ 0.9997. The limits of detection (LOD) were 140 and 100 mg/L and the limits of quantification (LOQ) were 470 and 330 mg/L for caffeine and trigonelline, respectively. The precision (% RSD) was 3.0% and 4.3% for caffeine and trigonelline, respectively. The developed method was applied to 20 samples of green coffee beans to determine the two alkaloids. The amount of caffeine and trigonelline in the green coffee beans were found in the range 0.84 − 1.15% (w/w) and 0.83 − 1.13% (w/w), respectively. The accuracy of the developed analytical method was evaluated by spiking standard caffeine and trigonelline to green coffee beans and the average recoveries were 93 ± 5% and 98 ± 4%, respectively. Therefore, the developed FT-MIR-ATR methods can be used for direct determination of the two alkaloids in the green coffee beans.     

Trends of development in plasma techniques for atomic spectrometric analysis: A review

Trends of development in atomic spectrometry with plasma sources for optical emission spectrometry and mass spectrometry are discussed, especially for inductively coupled plasmas and discharges under reduced pressure. Important fields of application such as materials analysis and environmental analysis with special reference to the speciation of traces of heavy metals are discussed.Introductory lecture at the Symposium on Plasma Techniques of the 1994 International Symposium on Microchemical Techniques, Montreux, May 16–20, 1994     

The use of microemulsion for determination of sodium and potassium in biodiesel by flame atomic absorption spectrometry

A new method for F AAS determination of sodium and potassium in biodiesel using water-in-oil microemulsion as sample preparation is proposed. The method was investigated for biodiesel produced from different sources, as soybean, castor and sunflower oil and animal fat and was also applied for vegetable oils. The optimized condition for microemulsion formation was 57.6% (w/w) of n-pentanol, 20% (w/w) of biodiesel or vegetable oil, 14.4% (w/w) of Triton X-100 and 8% (w/w) of water (aqueous standard of KCl or NaCl in/or diluted HNO₃). The optimized instrumental parameters were: aspiration rate of 2 mL min⁻¹ and the flame composition of 0.131 of C₂H₂/air ratio. For comparison purpose, the determination of sodium and potassium were also carried out according to European norms (EN 14108 and EN 14109, respectively). These norms are applied for determination of sodium and potassium in fatty acid methylic ester samples and consist in the sample dilution using organic solvent and determination by F AAS. The stability of microemulsified aqueous standards and samples was investigated and it was found to be stable for at least 3 days while the organic standard diluted with xylene showed a decrease around of 15% in the analytical signal in 1 h. The limits of detection were 0.1 μg g⁻¹ and 0.06 μg g⁻¹ and the obtained characteristic concentrations were 25 μg L⁻¹ and 28 μg L⁻¹ for sodium and potassium, respectively. The proposed method presented two times better limits of detection and better precision (0.4–1.0%) when compared with the dilution technique (1.5–4.5%). The accuracy of the method was evaluated through recovery tests and comparison with the results obtained by dilution technique. The recoveries ranged from 95% to 115% for biodiesel and 90% to 115% for vegetable oil samples. Comparison between the results obtained for biodiesel by both methods showed no significant differences at the 95% confidence level according to a Student's t-test. This study shows that the proposed method based on microemulsion as sample preparation can be applied as an efficient alternative for sodium and potassium determination in biodiesel samples.     

Method development for the determination of manganese, cobalt and copper in green coffee comparing direct solid sampling electrothermal atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry

A method has been developed for the determination of cobalt, copper and manganese in green coffee using direct solid sampling electrothermal atomic absorption spectrometry (SS-ET AAS). The motivation for the study was that only a few elements might be suitable to determine the origin of green coffee so that the multi-element techniques usually applied for this purpose might not be necessary. The three elements have been chosen as test elements as they were found to be significant in previous investigations. A number of botanical certified reference materials (CRM) and pre-analyzed samples of green coffee have been used for method validation, and inductively coupled plasma optical emission spectrometry (ICP OES) after microwave-assisted acid digestion of the samples as reference method. Calibration against aqueous standards could be used for the determination of Mn and Co by SS-ET AAS, but calibration against solid CRM was necessary for the determination of Cu. No significant difference was found between the results obtained with the proposed method and certified or independently determined values. The limits of detection for Mn, Cu and Co were 0.012, 0.006 and 0.004 μg g⁻¹ using SS-ET AAS and 0.015, 0.13 and 0.10 μg g⁻¹ using ICP OES. Seven samples of Brazilian green coffee have been analyzed, and there was no significant difference between the values obtained with SS-ET AAS and ICP OES for Mn and Cu. ICP OES could not be used as a reference method for Co, as essentially all values were below the limit of quantification of this technique.     

Characterization of Heavy Metal Air Pollution in Romania Using Moss Biomonitoring,Neutron Activation Analysis,and Atomic Absorption Spectrometry

ABSTRACT

Heavy metal air pollution in Romania was investigated by using passive moss biomonitoring. This study is a component of an international UNECE ICP Vegetation Program – moss survey. A total of 330 samples of Hypnum cupressiforme, Hylocomium splendens, Pleurozium schreberi, and other mosses were collected in Romania in the summer and autumn of 2010. The concentrations of aluminum, cadmium, chromium, copper, iron, lead, nickel, vanadium, and zinc were determined by graphite furnace/flame atomic absorption spectrometry and instrumental neutron activation analysis. The results were statistically processed to obtain spatial distribution maps of factor scores based on elemental concentrations in the moss, together with the spatial distribution maps of heavy metals in moss. The median concentrations of cadmium, 1.20?mg/kg dry weight, and lead, 30.8?mg/kg dry weight, were high compared with other European countries. The results revealed that the atmospheric deposition of these metals is a problem in north and northwest Romania.     

Investigation of the feasibility to use Zeeman-effect background correction for the graphite furnace determination of phosphorus using high-resolution continuum source atomic absorption spectrometry as a diagnostic tool

The determination of phosphorus by graphite furnace atomic absorption spectrometry at the non-resonance line at 213.6 nm, and the capability of Zeeman-effect background correction (Z-BC) to deal with the fine-structured background absorption due to the PO molecule have been investigated in the presence of selected chemical modifiers. Two line source atomic absorption spectrometers, one with a longitudinally heated and the other with a transversely heated graphite tube atomizer have been used in this study, as well as two prototype high-resolution continuum source atomic absorption spectrometers, one of which had a longitudinally arranged magnet at the furnace. It has been found that Z-BC is capable correcting very well the background caused by the PO molecule, and also that of the NO molecule, which has been encountered when the Pd + Ca mixed modifier was used. Both spectra exhibited some Zeeman splitting, which, however, did not cause any artifacts or correction errors. The practical significance of this study is to confirm that accurate results can be obtained for the determination of phosphorus using Z-BC.     

Application of a new ion-imprinted polymer for solid-phase extraction of bismuth from various samples and its determination by ETAAS

A batch process was developed to extract bismuth ions by a novel and selective sorbent. In this study, a new Bi(III)-ion imprinted polymer was prepared by formation of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex for selective preconcentration of ultra trace amounts of bismuth. Polymerization was performed with ethylene glycol dimethacrylate, as crosslinking monomer and methacrylic acid as functional monomer; in the presence of 2,2-azobisisobutyronitrile, as initiator, via bulk polymerization. Optimum pH for maximum sorption was 2.5–3.5. Maximum sorbent capacity and enrichment factor for bismuth were 35.9?mg?g^?1 and 300, respectively. The relative standard deviation and limit of detection the method were evaluated as ±4.1% and 8.6?ng?L^?1. This method is simple, selective and sensitive and can be applied to the determination of bismuth in water, biological and plant samples.     

A direct solid sampling electrothermal atomic absorption spectrometry method for the determination of silicon in biological materials

A solid sampling electrothermal atomic absorption spectrometry method for direct determination of trace silicon in biological materials was developed and applied to analysis of pork liver, bovine liver SRM 1577b and pure cellulose. The organic matrix was destroyed and expelled from the furnace in the pyrolysis stage involving a step-wise increasing the temperature from 160 °C to 1200 °C. The mixed Pd/Mg(NO₃)₂ modifier has proved to be the optimum one with respect to the achievement of maximum sensitivity, elimination of the effect of the remaining inorganic substances and the possibility of using calibration curves measured with aqueous standard solutions for quantification. For the maximum applicable sample amount of 6 mg, the limit of detection was found to be 30 ng g^− 1. The results were compared with those obtained by different spectrometric methods involving sample digestion, by electrothermal atomic absorption spectrometry using slurry sampling, by wavelength dispersive X-ray fluorescence spectrometry and by radiochemical neutron activation analysis. The method seems to be a promising one for analysis of biological materials containing no significant fraction of silicon in form of not naturally occurring volatile organosilicon compounds. The still incessant serious limitations and uncertainties in the determination of trace silicon in solid biological materials are discussed.     

Titanium as a chemical modifier for the determination of cobalt in marine sediments

The determination of cobalt in marine sediments by electrothermal atomic absorption spectrometry was studied using no modifier and magnesium and titanium as modifiers. Titanium is one of the major sediment constituents, which widely affects the cobalt determination and it was studied as a chemical modifier since it was the only concomitant that increased the cobalt signal in the concentration range usually found in sediments. The performance of Mg and Ti as chemical modifiers was compared relative to maximum pyrolysis and atomization temperatures, linear calibration range, sensitivity and matrix effects. The pyrolysis curves showed that the analyte could be stabilized up to 1400 °C when either Ti or Mg(NO₃)₂ was present, while only 1000 °C could be used in the absence of a modifier. The optimum atomization temperature was 2500 °C in all cases. Analytical curves were compared using no modifier, 5 μg Ti and 100 μg Mg(NO₃)₂ as modifiers, and the linear range found was up to approximately 4 ng Co whether a modifier was used or not. With Ti as a chemical modifier, analytical curves for cobalt in aqueous solution and in a synthetic matrix resulted in the same sensitivity (m₀=55 pg), whereas the use of Mg led to characteristic mass values of 59 and 72 pg in aqueous solution and in a synthetic matrix, respectively, showing some matrix effect. The detection limits (3σ, n=10) were 0.4 μg g⁻¹ using no modifier and 0.3 μg g⁻¹ with Ti as a modifier in the original matrix. A reference estuarine sediment NIST 1646 with a non-certified content of 10.5 μg g⁻¹ Co was analyzed and the found value of 10.9±2.4 μg g⁻¹, (n=3), using Ti as chemical modifier and calibration against aqueous standards, was in good agreement with the recommended value.     

Platinum determination by instrumental neutron activation analysis with special reference to the spectral interference of Sc-47 on the platinum indicator nuclide Au-199

A method of instrumental neutron activation analysis (INAA) is developed for the determination of platinum by the ¹⁹⁹Au daughter of ¹⁹⁹Pt in the presence of the spectral interference from the ⁴⁷Sc daughter of ⁴⁷Ca. The contributions of the Pt and Ca signals to the integral 157–161 keV peak were separated by calculating the number of disintegrations due to the ⁴⁷Sc from the signal of her parent ⁴⁷Ca at 1297.1 keV γ-ray. The method was used to calculate the trace concentrations of Pt in air samples, collected on filters.     

Flow injection analysis-flame atomic absorption spectrometry system for indirect determination of cyanide using cadmium carbonate as a new solid-phase reactor

A new and simple flow injection system procedure has been developed for the indirect determination of cyanide. The method is based on insertion of aqueous cyanide solutions into an on-line cadmium carbonate packed column (25% m/m suspended on silica gel beads) and a sodium hydroxide with pH 10 is used as the carrier stream. The eluent containing the analyte as cadmiumcyanide complexes, produced from reaction between cadmium carbonate and cyanide, measured by flame atomic absorption spectrometry. The absorbance is proportional to the concentration of cyanide in the sample. The linear range of the system is up to 15 mg L⁻¹ with a detection limit 0.2 mg L⁻¹ and sampling rate 72 h⁻¹. The method is suitable for determination of cyanide in industrial waste waters with a relative standard deviation better than 1.22%.     

Quantitative analysis of volatiles from solid matrices of vegetable origin by high concentration capacity headspace techniques: determination of furan in roasted coffee

The study compares standard addition (SA), stable isotope dilution assay (SIDA) and multiple headspace extraction (MHE) as methods to quantify furan and 2-methyl-furan in roasted coffee with HS-SPME-GC-MS, using CAR-PDMS as fibre coating, d(4)-furan as internal standard and in-fibre internal standardization with n-undecane to check the fibre reliability. The results on about 150 samples calculated with the three quantitation approaches were all very satisfactory, with coefficient of variation (CV) versus the U.S. Food and Drug Administration (FDA) method, taken as reference, almost always below the arbitrarily-fixed limit of 15%. Furan was detected in the 1-5 ppm range, 2-methyl-furan in the 4-20 ppm range. Moreover, experimental exponential slopes (Q) and linearity (r) of both furan and 2-methyl-furan MHE regression equation on 50 samples were very similar thus making possible to use the same average Q value for all samples of the investigated set and their quantitation with a single determination. This makes this approach very rapid and competitive in-time with SA and SIDA. A non-separative method (HS-SPME-MS) was also developed in view of possible application on-line monitoring of furan and 2-methyl-furan in a pilot-plant with the aim of optimizing the roasting process to reduce these compounds to a minimum. Sampling times of 20 and 5 min were tested, the latter enabling total analysis time to be reduced to about 9 min. The results on 105 samples with both SIDA and MHE approaches were again highly satisfactory most of the samples giving a CV% versus the conventional methods below 20%. In this case too average Q values for both furan and 2-methyl-furan were used for MHE. The separative method presented very good repeatability (RSD% always below 10%) and intermediate precision over three months (RSD% always below 15%); performance were similar for the non-separative method, with repeatability (RSD%) always below 12% and intermediate precision over three months (RSD%) always below 15%. The sensitivity of both separative and non-separative methods was also very good, LOD and LOQ being in the ppb range for both furan and 2-methyl-furan, i.e. well below the amounts present in the roasted coffee samples.     

Method development for the determination of cadmium in fertilizer samples using high-resolution continuum source graphite furnace atomic absorption spectrometry and slurry sampling

The determination of cadmium (Cd) in fertilizers is of major interest, as this element can cause growth problems in plants, and also affect animals and humans. High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) with charge-coupled device (CCD) array detection overcomes several of the limitations encountered with conventional line source AAS, especially the problem of accurate background measurement and correction. In this work an analytical method has been developed to determine Cd in fertilizer samples by HR-CS GF AAS using slurry sampling. Both a mixture of 10 μg Pd + 6 μg Mg in solution and 400 μg of iridium as permanent modifier have been investigated and aqueous standards were used for calibration. Pyrolysis and atomization temperatures were 600 °C and 1600 °C for the Pd-Mg modifier, and 500 °C and 1600 °C for Ir, respectively. The results obtained for Cd in the certified reference material NIST SRM 695 (Trace Elements in Multi-Nutrient Fertilizer) of 16.7 ± 1.3 μg g⁻¹ and 16.4 ± 0.75 μg g⁻¹ for the Pd-Mg and Ir modifier, respectively, were statistically not different from the certified value of 16.9 ± 0.2 μg g⁻¹ on a 95% confidence level; however, the results obtained with the Ir modifier were significantly lower than those for the Pd-Mg modifier for most of the samples. The characteristic mass was 1.0 pg for the Pd-Mg modifier and 1.1 pg Cd for the Ir modifier, and the correlation coefficients (R²) of the calibration were > 0.99. The instrumental limits of detection were 7.5 and 7.9 ng g⁻¹, and the limits of quantification were 25 and 27 ng g⁻¹ for Pd-Mg and Ir, respectively, based on a sample mass of 5 mg. The cadmium concentration in the investigated samples was between 0.07 and 5.5 μg g⁻¹ Cd, and hence below the maximum value of 20 μg g⁻¹ Cd permitted by Brazilian legislation.     

Application of ICP-MS for Multielement Analysis in Small Sample Amoun ts of Pathological Thyroid Tissue

 As a result of the Chernobyl nuclear power plant accident in 1986, thyroid pathologies occurred among children in some regions of Belarus. Besides the irradiation of children’s thyroids by radioactive iodine and caesium nuclides, toxic elements from fallout are a direct risk to health. Inductively coupled plasma quadrupole-based mass spectrometry was used for multielement determination in small amounts (1–10 mg) of thyroid tissue samples obtained during thyroid operations in Minsk hospitals. The accuracy of the applied analytical technique for small biological sample amounts was checked using NIST Standard Reference Material oyster tissue (SRM 1566b) and by comparison with independent analytical methods, such as neutron activation analysis. Almost all essential elements as well as a number of toxic elements such as Cd, Pb, Hg, U etc. were determined in a multitude of human and animal thyroid tissues (up to 1 mg sample material) by quadrupole-based ICP-MS using micronebulization. In general, the thyroid tissue affected by pathology is characterized by higher calcium content. Some other elements, among them Fe, Mn, V, As, Cr, Ni, Pb, U, Ba, Sb, were also accumulated in such tissue. The results obtained will be used as initial material for further specific studies of the role of particular elements in thyroid pathology development. Received November 15, 1999. Revision March 15, 2000.     

Synthesis and characterisation of a silicon oxide film solid-phase extraction system for lead traces determination: an all the way green analytical method

In this work, an all the way green analytical procedure based on a silicon oxide film-solid phase extraction system is proposed for lead traces determination. From the synthesis of a solid phase extraction (SPE) system and throughout the metal preconcentration and determination only aqueous media were employed. Characterisation of the film was carried out by Scanning Electron Microscopy and Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy. Preconcentration conditions, prior to Pb(II) Electrothermal Atomic Absorption Spectrometry (ETAAS) determination, such as adsorption and desorption time, pH and temperature, were optimised. Langmuir, Freundlich and Dubinin-Radushkevich isotherm models were analysed along with the evaluation of adsorption energy and standard free energy (ΔG ⁰). The greatest adsorption was obtained with incubation at pH 7 and 37°C. By using a small volume of 0.5?mol?L^?1 HNO₃ (0.5?mL) lead was desorbed from the silicon oxide film after 2?h incubation, generating low amount of waste. The films showed better adjustment for the Langmuir model (R^{2 ?}=?0.989). The detection limit (3.29σ) for Pb(II) was 0.228?µg?L^?1. The developed procedure is 10-fold more sensitive in comparison to direct ETAAS determination. Recovery values from soft tap-water and soft well-water were above 95%. When hard water was analysed, Pb(II) adsorption was found to be interfered by Mg²⁺ and Ca²⁺. After five preconcentration cycles relative recovery was found not to decay below 90%, indicating that the silicon oxide film could be used for multiple lead determinations.     

Combined use of atomic spectrometric methods in the analysis of rocks

Standard reference materials of limestone, granite and argillite were analyzed by X-ray fluorescence spectrometry (XFS), flame and graphite furnace atomic absorption spectrometry (F-AAS and G-AAS), and inductively coupled plasma atomic emission spectrometry (ICP-AES). The major elements Al, Ca, Fe, Si and Ti were determined by XFS and ICP-AES. The relative standard deviations (RSD) of the concentrations of the corresponding oxides obtained by XFS and ICP-AES were (1.36±0.51)% (n=18) and (1.30±0.70)% (n=17), respectively, on the average. The relative deviations (RD) from the certified values were (1.29±3.01)% (n=18) and (–0.69±5.48)% (n=14), respectively, on the average. The numbers in parentheses are the numbers of the single RSD- and RD-values used for the calculation of the averages and the relative standard deviations. Some minor and trace elements of the standard reference materials were determined by G-AAS and ICP-AES. The precision (RSD) was markedly better in the case of ICP-AES. On the other hand, the accuracy (RD) of both methods was about the same (7%). Apparently, the precision and the accuracy are primarily determined by the measuring technique and the sample pretreatment procedure, respectively. The analytical power of the combined use of atomic spectrometric methods is also discussed.     

A green method for the determination of hypochlorite in bleaching products based on its native absorbance

A new, green method for the determination of hypochloride in bleaching products is here presented. The method, based on a flow injection system and measurement of the native absorbance of hypochlorite at 292 nm, allows the determination of hypochlorite in the range 0.07-0.42 g Cl₂ l⁻¹. In order to achieve high selectivity a mini-column containing cobalt oxide, which effectively catalyses hypochlorite decomposition to chloride and oxygen, was inserted in the flow system. The difference in absorbance of samples no circulated and circulated through the mini-column was selected as analytical signal; thus, the method only requires 20 mg of solid, reusable catalyst, and a NaOH solution of pH 10.4; providing a sample throughput of 12 samples h⁻¹ in triplicate injection. Its usefulness for analysis of bleaching products is demonstrated.     

Chemometric investigation of systematic error in the analysis of biological materials by flame and electrothermal atomic absorption spectrometry

Systematic errors observed when using flame atomic absorption spectrometry (FAAS) and electrothermal atomic spectrometry (ETAAS) for the analysis of biological solid materials (seafood products) were evaluated. The effect of the sample pre-treatment method (microwave-assisted acid digestion, ultrasound-assisted acid leaching and slurry sampling) as well as the number of times that a certain pre-treatment process is repeated, were two factors evaluated. They give information about the effect of the sample pre-treatment on the uncertainty in the analysis. In addition, the number of measurements (i.e., number of times that an acid digest, an acid leachate or aqueous slurry are analysed) and the calibration technique used (aqueous calibration method or standard addition technique) were other two variables taken into account. This last factor gives information about the effect of the calibration on the results, while the replicate measurements showed the repeatability. A fifth variable named as sample matrix tests the influence of the matrix sample on the systematic error through the use of different reference materials. This variable allows the study of the effect of the trace element concentrations on the uncertainty because the trace elements contents are different in each reference material. Experimental design and principal component analysis approaches were used as chemometric tools. It has been found that the use of the slurry sampling technique in ETAAS and FAAS and the determination of high element concentrations by ETAAS have led to poor precision.     

Comparison of high performance TLC and HPLC for separation and quantification of chlorogenic acid in green coffee bean extracts

Two chromatographic methods, high-performance TLC (HPTLC) and HPLC, were developed and used for separation and quantitative determination of chlorogenic acid in green coffee bean extracts. For HPTLC silica gel Kieselgel 60 F 254 plates with ethyl acetate/dichlormethane/formic acid/acetic acid/water (100:25:10:10:11, v/v/v/v/v) as mobile phase were used. Densitometric determination of chlorogenic acid by HPTLC was performed at 330 nm. A gradient RP HPLC method was carried out at 330 nm. All necessary validation tests for both methods were developed for their comparison. There were no statistically significant differences between HPLC and HPTLC for quantitative determination of chlorogenic acid according to the test of equality of the means.     

Automated on-line separation preconcentration system for palladium determination by graphite furnace atomic absorption spectrometry and its application to palladium determination in environmental and food samples

A flow injection (FI) system was used to develop an efficient on-line sorbent extraction preconcentration system for palladium by graphite furnace atomic absorption spectrometry (GFAAS). The investigated metal was preconcentrated on a microcolumn packed with 1,5-bis(di-2-pyridyl)methylene thiocarbohydrazide immobilized on silica gel (DPTH-gel). The palladium is eluted with 40 μl of HCl 4 M and directly introduced into the graphite furnace. The detection limit for palladium under the optimum conditions was 0.4 ng ml⁻¹. This procedure was employed to determine palladium in different samples.