Adsorption of lysozyme on a hemodialysis sulfonated polyacrylonitrile membrane, with and without preadsorbed poly(ethyleneimine) on the external faces

We present the influence of pH, from pH 4 to 10, with a focus on the neutral range, on the adsorption of lysozyme (isoelectric point pI=11) on a sulphonated membrane and the same membrane pre-treated with poly(ethyleneimine) (PEI). We found a steep increase of the adsorbed amount above pH 6 in phosphate buffer. The adsorbed amount was about twice as low in Tris buffer, around the neutral pH. The difference between the two types of buffer is attributed to their different ionic composition. High interfacial concentration in phosphate buffer is especially linked to the phosphate divalent anions. In the presence of divalent sulphate anions, we measured the same level of interfacial concentration than with phosphate buffer. With the PEI pre-treated membrane, we observed, on the time scale of our experiments (15–20 h), similar adsorbed amounts than on the raw membrane, showing that the PEI layer does not constitute a true barrier to the penetration of lysozyme into the membrane core. However, its presence leads to a slower adsorption rate in a system where convection does not occur through the membrane.     

Adsorption mechanism of polylysine on hydroxyapatite and its effect on dissolution properties of hydroxyapatite

Adsorbed amounts of poly-l-lysine (pLys) and bromide ion on hydroxyapatite (HAp) from aqueous solutions of poly-l-lysine hydrobromide, and amounts of calcium and phosphate ions liberated concurrently from HAp during the adsorption of pLys were determined at 25 degrees . The pLys was adsorbed on HAp by the mechanism of ion-exchange between its amino groups and calcium ions of HAp. The released amount of calcium ion increased, therefore, with the adsorbed amount of pLys. On the other hand, the released amount of phosphate ion first decreased and then increased after attaining a minimum with the equilibrium concentration of pLys. The analysis using an equilibrium dialysis method revealed that the released phosphate ions were mainly in the bound state to the amino groups of pLys remaining in the solution, and that the concentrations of calcium and phosphate ions free from both HAp and pLys were restricted by each other under the law of the solubility product of HAp. The first decrease in the released amount of phosphate ion was concluded to be attributed primarily to the increase in the released amount of calcium ion because pLys remaining in the solution was little in this region. When sodium hydroxide was added to the solution, the adsorbed amount of pLys increased and then slightly decreased with the equilibrium pH of the solution due to the increase or decrease of the electrostatic attractive force between the adsorbate and the adsorbent. However, conformational change in pLys around pH 10 seemed to have little effect on the adsorption.     

Evaluation of the adsorption affinity of proteins to calcium hydroxyapatites by desorption and pre-adsorption methods

The adsorption affinity of bovine serum albumin (BSA) and lysozyme (LSZ) to calcium hydroxyapatite (CaHAP) was evaluated by desorption and two step adsorption methods. These experiments were carried out at 15°C in a 1×10⁻⁴ mol dm⁻³ KCl solution of pH 6.0. BSA molecules were scarcely desorbed, exhibiting an irreversible adsorption of BSA, though LSZ slightly desorbed. This result supports our previous findings that LSZ adsorbs weakly onto phosphate ions exposed on ac or bc faces of CaHAP while BSA adsorbs strongly onto positively charged sites on ac or bc faces of CaHAP. The amount of adsorbed LSZ was markedly increased by the pre-adsorption of BSA, where LSZ was adsorbed onto BSA-covered CaHAP. On the other hand, the amount of adsorbed BSA was not changed by the pre-adsorption of LSZ. In both pre-adsorption systems it was confirmed by an HPLC method that no protein molecule pre-adsorbed was desorbed after the post-adsorption procedure. Therefore, it was interpreted that the enhancement of adsorption of positively charged LSZ is induced by an electrostatic attractive force through pre-adsorption of negatively charged BSA molecules with a high coverage. However, since the coverage of LSZ onto CaHAP is considerably low, no stimulation of BSA adsorption occurred on the LSZ-covered surface. The formation of double protein adsorbed layers consisting of pre- and post-adsorbed proteins was proposed.     

Removal of phosphate by aluminum oxide hydroxide

The development and manufacture of an adsorbent to remove phosphate ion for the prevention of eutrophication in lakes are very important. The characteristics of phosphate adsorption onto aluminum oxide hydroxide were investigated to estimate the adsorption isotherms, the rate of adsorption, and the selectivity of adsorption. Phosphate was easily adsorbed onto aluminum oxide hydroxide, because of the hydroxyl groups. The adsorption of phosphate onto aluminum oxide hydroxide was influenced by pH in solution: the amount adsorbed was greatest at pH 4, ranging with pH from 2 to 9. The optimum pH for phosphate removal by aluminum oxide hydroxide is 4. The selectivity of phosphate adsorption onto aluminum oxide hydroxide was evaluated based on the amount of phosphate ion adsorbed onto aluminum oxide hydroxide from several anion complex solutions. It is phosphate that aluminum oxide hydroxide can selectively adsorb. The selectivity of phosphate onto aluminum oxide hydroxide was about 7000 times that of chloride. This result indicated that the hydroxyl groups on aluminum oxide hydroxide have selective adsorptivity for phosphate and could be used for the removal of phosphate from seawater.     

Lysozyme Adsorption onto Different Supports: A Comparative Study

The interaction between proteins and solid surfaces has been investigated. The aim of this work is to compare three different materials (hydroxyapatite, polystyrene with core-shell structure (PE-CS) and a functionalized styrene divinylbenzene copolymer) to be used as adsorbents for lysozyme, known as a “hard” protein. Tests were performed according to an experimental design in order to compare the effects of pH, lysozyme and phosphate buffer concentration onto the adsorbed amount of protein. A 2³ factorial design and a cross design, which was performed in triplicate, were used to distinguish the most important variables and to infer about the interaction between them. Hydroxyapatite showed the best performance—higher adsorbed amount of lysozyme and smaller dispersion (72.2 ± 0.9 mg/g). However, PE-CS can be regarded as a promising support as high amounts of lysozyme are adsorbed onto this material with relatively small dispersion.     

A cyclic voltammetry study of the adsorption of alcohol dehydrogenase (HLADH) onto a platinum electrode

A cyclic voltammetry study of the interfacial behaviour of horse liver alcohol dehydrogenase (HLADH) at a Pt surface in a phosphate buffer solution pH 7.0 over the temperature range 273 to 353 K is presented. The surface charge density, resulting from protein adsorption, was shown to be directly proportional to the amount of adsorbed protein (surface concentration). HLADH exhibits very high affinity towards adsorption onto a Pt surface via chemisorption. The Langmuir isotherm was employed for modeling the adsorption process and the values of the Gibbs free energy, enthalpy and entropy of adsorption were calculated. The thermodynamic data suggested that disruption of tertiary structure of the protein occurs upon adsorption at the Pt surface and that the breaking of intramolecular interactions during the adsorption governs the rate of the process.     

Adsorption behavior of statherin and a statherin peptide onto hydroxyapatite and silica surfaces by in situ ellipsometry

The salivary protein statherin is known to adsorb selectively onto hydroxyapatite (HA), which constitutes the main mineral of the tooth enamel. This adsorption is believed to be crucial for its function as an inhibitor of primary (spontaneous) and secondary (crystal growth) precipitation of calcium phosphate salts present in saliva. A fragment corresponding to the first 21 N-terminus amino acids of statherin (StN21) was previously found to reduce the rate of demineralization of HA. Therefore, the interfacial properties of this peptide and statherin onto silica, hydrophobized silica and HA discs was studied by in situ ellipsometry. Their reversibility induced by dilution and elutability induced by buffer and sodium dodecyl sulfate (SDS) was also determined. The results revealed that statherin adsorbed at a greater extent onto the HA as compared to StN21, suggesting that the hydrogen bonding between the uncharged polar residues at the C-terminal region of statherin and HA contributes to its adsorption. However, on both silica surfaces the peptide adsorption appeared to proceed in a similar way. Onto the hydrophobized silica the adsorption of both peptides was suggested to occur either via multilayer formation or adsorption of aggregates from solution, while onto the hydrophilic silica adsorption of peptide aggregates from solution was the suggested mechanism. Further, both peptides were observed to be strongly adsorbed onto HA, even after SDS treatment, in comparison to the layers adsorbed onto hydrophobized silica. Both peptide layers were found to be weakly adsorbed onto the hydrophilic silica surface as they were totally removed by buffer dilution.     

Capillary electrochromatographic separation of proteins on a column coated with titanium dioxide nanoparticles

A TiO2 nanoparticle (TiO2 NP)-coated open-tubular column for the capillary electrochromatographic separation of proteins is described. The surface chemistry of the TiO2 NPs on the inner wall of the fused silica was significantly affected by the running buffer. By varying of the phosphate buffer pH, only cathodic EOF was indicated. The results showed that TiO2 NPs are existed as a complexed form with the buffer ligand. Good separation of conalbumin (ConA), apo-transferrin (apoTf), ovalbumin (OVA), and BSA could be achieved with phosphate buffer (40 mM, pH 8.0) and an applied voltage of 15 kV. Five peaks of glycoisoforms of OVA were observed under these conditions. In comparison with the retention behavior of the analytes on the bare fused-silica column, the new column's high resolving power seems to be predominantly derived from the ligand exchange of the analytes with the phosphate adsorbed onto the TiO2 NPs. The method was also used to separate egg-white proteins. Both acidic and basic proteins in egg white were separated in a single run. The microheterogeneities of OVA could also be found in it. The separation efficiency for the main peak of OVA in egg white was around 10,000 plates/m.     

Preparation of thin polymer films with drug release and protein adsorption resistance

Thin polymer films with the ability of both drug release and protein adsorption resistance were formed on silicon substrates and silica particles. The films were made of a block copolymer of poly(N-isopropylacrylamide) (p(AAm)) that can load and release drugs and poly(2-methoxyethyl methacrylate) (p(MEMA)) that can suppress protein adsorption. Aspirin and bovine serum albumin were respectively used as model substances for testing the abilities of the films to load and release drugs and to suppress protein adsorption. The films were immersed in a phosphate buffer saline (pH 7.4) for 100 days to evaluate their water resistance. The experimental results showed that the films have both drug release and protein adsorption resistance and are highly stable against PBS.     

溶菌酶在裸金电极和疏基乙酸或正十二疏烷基醇修饰电极上的吸附

电化学石英晶体阻抗系统;疏基乙酸;溶菌酶在裸金电极和疏基乙酸或正十二疏烷基醇修饰电极上的吸附     

Adsorption of fluoride ions onto carbonaceous materials

The characteristics of fluoride ion adsorption onto carbonaceous materials were derived as adsorption isotherms at different temperatures and in different pH solutions. The fluoride ion was adsorbed into pores in carbonaceous materials produced from wood; the larger the specific surface area, the more fluoride ions adsorbed. Bone char was the most effective adsorbent. The composition of bone char includes calcium phosphate, calcium carbonate, and so on. This suggests that the phosphate ion in bone char was exchanged with a fluoride ion. Moreover, the mechanism of fluoride ion adsorption onto bone char is clearly chemical in nature because the amount of fluoride ion adsorbed onto bone char increased with increasing temperature and decreasing pH. The amount of fluoride ion adsorbed onto bone char was also shown to depend on the concentration of sodium chloride in solution because of the "salting-out" effect. The adsorption of fluoride ion onto bone char is endothermic. Bone char can be utilized to remove fluoride ions from drinking water.     

Characteristics of granular boehmite and its ability to adsorb phosphate from aqueous solution

In this study, we investigated the surface properties of granulated boehmite with vinyl acetate (G-BE20) and measured the amount of phosphate it adsorbed and the effect of contact time and solution pH on the adsorption process. The specific surface area (144.9?m²/g) and the number of surface hydroxyl groups (0.88?mmol/g) of G-BE20 were smaller than those of virgin boehmite (BE), which gave a specific surface area and number of surface hydroxyl groups of 297.0?m²/g and 1.08?mmol/g, respectively. The amount of phosphate adsorbed increased with the temperature. The isotherm model of Langmuir was used to fit experimental adsorption equilibrium data for phosphate adsorption onto G-BE20. The calculated thermodynamic parameters show the spontaneous and endothermic nature of the adsorption process. The equilibrium adsorption onto G-BE20 was reached within 16?h and the amount of phosphate adsorbed was 8.4?mg/g. The kinetic mechanism of phosphate uptake was evaluated with two different models: the Largergren pseudo first- and pseudo second-order models. The data obtained showed a better fit to the pseudo second-order model (0.991) than to the pseudo first-order model (0.967), as indicated by the r values. The rate constants for the adsorption of phosphate onto G-BE20 were calculated as 0.481?1/h and 0.029?g/mg?h. The adsorption of phosphate onto G-BE20 was the maximum in the pH range 3.0-4.0.     

Adsorption of egg albumin onto methylated yeast biomass

A new biosorbent, methylated yeast (MeYE), was prepared for the adsorptive separation of proteins from aqueous solutions. Yeast was methylated in a 0.1 M HCl methyl alcohol solution at room temperature. About 80% of the carboxylic groups of yeast could be methylated within 9 h. The adsorption of egg albumin onto MeYE was studied to evaluate the protein adsorption ability of MeYE. At near neutral pH, egg albumin was scarcely adsorbed onto unmethylated yeast and the adsorbed amount of egg albumin increased with increasing methylation degree. The amount of egg albumin adsorbed onto MeYE increased with increasing pH from 4 to 7 and steeply decreased above pH 7. The Langmuir isotherm was applied to determine the apparent adsorption constant and the saturated adsorbed amount of egg albumin on MeYE. Both the apparent adsorption constant and the saturated adsorbed amount increased with the degree of methylation. The saturated adsorbed amount of egg albumin onto MeYE having methylation degree 77% was 8.41 x 10(-6) mol g(-1) or 0.378 gg(-1) at near neutral pH.     

Release characteristics of a free polyunsaturated fatty acid from an oily lymphographic agent

The release profiles of a free polyunsaturated fatty acid, alpha-linolenic acid, from solutions in an oily lymphographic agent Lipiodol-Ultra-Fluid (Lipiodol), to rabbit and human plasma, phosphate buffer solution (PBS), and PBS containing bovine serum albumin (BSA) were examined in vitro. The times required for 50% release of alpha-linolenic acid from Lipiodol were about 1 and 1.5 h in the rabbit and human plasma, respectively. Although only a slight amount of alpha-linolenic acid was released from Lipiodol to PBS after 24 h incubation at 37 degrees C, release was markedly enhanced by the addition of BSA to PBS. The amount of alpha-linolenic acid released from Lipiodol into PBS containing 5% BSA increased as the alpha-linolenic acid content in Lipiodol was increased. In all experiments, the release had stopped before all alpha-linolenic acid had been released. The prolongation of alpha-linolenic acid release from Lipiodol is considered a requisite for a selective anticancer effect of Lipiodol containing a free fatty acid on liver cancer.     

Studies on manganese nodule leached residues 2. Adsorption of aqueous phosphate on manganese nodule leached residues

Adsorption of phosphate onto manganese nodule leached residues was investigated as a possible alternative to conventional methods of phosphate removal from industrial effluents. Adsorption behaviors were studied as a function of time, temperature, pH, and concentration level of adsorbate and adsorbent in acetic acid-sodium acetate buffer medium. The adsorption of phosphate follows the Langmuir adsorption isotherms. The magnitude of adsorption of phosphate in manganese nodule leached residues was compared with that in naturally occurring Mn nodule. Manganese nodule leached residues show better affinity toward phosphate adsorption.     

Adsorption and spectroscopic characterization of lactoferrin on hydroxyapatite nanocrystals

Lactoferrin (LF), a well-characterized protein of blood plasma and milk with antioxidant, cariostatic, anticarcinogenic and anti-inflammatory properties, has been adsorbed onto biomimetic hydroxyapatite (HA) nanocrystals at two different pH values (7.4 and 9.0). The interaction was herein investigated by spectroscopic, thermal and microscopic techniques. The positive electrostatic surface potential of LF at pH 7.4 allows a strong surface interaction with the slightly negative HA nanocrystals and avoids the protein-protein interaction, leading to the formation of a coating protein monolayer. In contrast, at pH 9.0 the surface potential of LF is a mix of negative and positive zones favouring the protein-protein interaction and reducing the interaction with HA nanocrystals; as a result a double layer of coating protein was formed. These experimental findings are supported by the good fittings of the adsorption isotherms by different theoretical models according to Langmuir, Freundlich and Langmuir-Freundlich models. The nanosized HA does not appreciably affect the conformation of the adsorbed protein. In fact, using FT-Raman and FT-IR, we found that after adsorption the protein was only slightly unfolded with a small fraction of the α-helix structure being converted into turn, while the β-sheet content remained almost unchanged. The bioactive surface of HA functionalized with LF could be utilized to improve the material performance towards the biological environment for biomedical applications.     

ATR-FTIR investigation on the complexation of myo-inositol hexaphosphate with aluminum hydroxide

The adsorption isotherm of and the pH effect on the adsorption of myo-inositol hexaphosphate (myo-IP6) on amorphous aluminum hydroxide was investigated. It was found that the adsorption isotherm of myo-IP6 on aluminum hydroxide could be well fitted with the Freundlich isotherm. The amount of myo-IP6 adsorbed remained almost constant in the range of pH 4.0 to 7.0, but it decreased considerably as the initial pH was over 7. The adsorption of myo-IP6 resulted in an increase in the pH level due to the release of OH(-) ions, which suggested that the adsorption of myo-IP6 on aluminum hydroxide was caused by a ligand exchange reaction. ATR-FTIR analysis of myo-IP6 in solution and adsorbed on aluminum hydroxide at different pH were performed. The ATR-FTIR investigation indicated that myo-IP6 was adsorbed onto aluminum hydroxide by forming inner-sphere complexes and adsorption facilitated the deprotonation of phosphate groups. The asymmetric vibration of the PO bond in AlPO(-)(3) appearing at a lower frequency than that in the terminal HPO(-)(3) indicated that Al bound to the O atom not as strongly as the H atom did. The ATR-FTIR investigation and theoretical calculation (with the Gaussian 03 program) revealed that three of the six phosphate groups in myo-IP6 molecules were bound to aluminum hydroxide while the other three remained free when myo-IP6 was adsorbed on aluminum hydroxide.     

Removal of Reactive Yellow 84 from aqueous solutions by adsorption onto hydroxyapatite

The adsorption of a reactive dye, Reactive Yellow 84, from aqueous solution onto synthesized hydroxyapatite was investigated. The experiments were carried out to investigate the factors that influence the dye uptake by the adsorbent, such as the contact time under agitation, absorbent dosage, initial dye concentration, temperature and pH of dye solution. The experimental results show that the amount of dye adsorbed increases with an increase in the amount of hydroxyapatite. The maximum adsorption occurred at the pH value of 5. The equilibrium uptake was increased with an increase in the initial dye concentration in solution. The experimental isotherm data were analyzed using Langmuir isotherm equation. The maximum monolayer adsorption capacity was 50.25 mg/g. The adsorption has a low temperature dependency and was endothermic in nature with an enthalpy of adsorption of 2.17 kJ mol⁻¹.     

Preparation and characterization of biodegradable poly(isobutylcyano acrylate) nanoparticles with the surface modified by the adsorption of proteins

The purpose of this work was to develop and characterize a biodegradable colloidal drug carrier which avoids uptake by the mononuclear phagocyte system. In order to imitate the cell surface, a sialic-acid-rich glycoprotein (human orosomucoid) was adsorbed onto poly(isobutylcyano acrylate) nanoparticles. The adsorption of human serum albumin and asialo-orosomucoid was also tested as a control. The adsorption was found to be dependent on the pH value and reached its maximum at a pH value close to the isoelectric point (pI) of each protein. The increase in the ionic strength due to the addition of NaCl generally resulted in an increase in the amount adsorbed. Considering the amounts of protein adsorbed (maximum of 4.5 mg m⁻²), the adsorption was assumed to be of the monolayer type. The adsorption kinetics performed at the pI of each protein showed that the equilibrium was reached within 1 h for albumin and within 8 h for the two glycoproteins. This significant difference suggested that conformational rearrangements could be much slower for the two glycoproteins than for the non-glycosylated albumin. The protein layer was found to be stable at pH 7 when the adsorption was performed beforehand at the pI, i.e. at an acidic pH. Finally, using hydrophobic interaction chromatography, the surface of the coated nanoparticles was found to be much more hydrophilic than the surface of the unmodified nanoparticles.     

Separation of human serum lipoproteins into three major classes by hydroxyapatite chromatography.

The separation of normolipidemic male serum lipoprotein fraction, prepared by ultracentrifugal flotation, was studied on hydroxyapatite columns. Potassium phosphate buffers in the pH range 5.6-7.4 were evaluated as eluents. The three main classes of the lipoproteins (high density, low density and very low density) can be separated on the Tiselius-type hydroxyapatite (Bio-Gel HTP DNA grade) column by elution with 75, 250 and 300 mM potassium phosphate buffer (pH 7.4), respectively.