梨醋半成品的超滤处理

用截留分子量不同的中空纤维超滤膜组件对梨醋半成品进行了处理.结果表明,使用截留分子量为1万的中空纤维超滤膜组件,在0.1 MPa压力差和室温下,将梨醋半成品超滤5 h,透过通量基本恒定在6 L/(m2.h).梨醋经过超滤,酸度保留率可达97.4%,糖度保留率88.3%,且风味不变,澄清透明,放置13个月无沉淀物.     

高性能MWCNTs-OH修饰聚偏氟乙烯中空纤维超滤膜的制备

以羟基多壁碳纳米管(MWCNTs-OH)作为添加剂,采用非溶剂致相转化法制备MWCNTs-OH修饰聚偏氟乙烯中空纤维超滤膜.先将MWCNTs-OH加入溶剂N,N-二甲基乙酰胺(DMAC)中超声处理以加强其分散性,力求制得均一铸膜液.通过水通量、截留率、红外光谱,XRD及力学性能测试表征膜性能,并用SEM观察其形貌.重点考察MWCNTs-OH对中空纤维膜通量、截留和力学性能的影响.结果表明,当MWCNTs-OH质量分数从0增加到0.09 wt%时,修饰膜的水通量由376.40 L/m2h增加到510.90 L/m2h,而对BSA截留率保持稳定(95%以上);膜的拉伸强度由1.68 MPa提高到2.42 MPa,断裂伸长率由44.18%提高到76.93%.SEM和TEM研究表明,MWCNTs-OH添加量较少时,在膜中可均匀分散,添加量大时则容易团聚.XRD和IR图谱分析表明MWCNTs-OH参与聚合物结晶过程而未改变聚合物晶型.     

Armos/聚砜共混中空纤维基膜及其纳滤复合膜的制备与性能研究

中空纤维膜因其体积装填密度高、占地面积小、成本相对低等优点备受关注。本文通过将Armos聚合液与聚砜(PSf)共混，经干-湿法纺丝制备了Armos/PSf共混中空纤维超滤膜，研究表明：Armos均匀分散在中空纤维膜中，中空纤维膜断面呈现疏松的多孔结构，随着Armos共混含量的增加，膜的亲水性和纯水通量均提高，但对PEG-20000截留率下降明显。以Armos/PSf共混中空纤维膜为基膜，通过界面聚合制备了中空纤维复合纳滤膜，优化的制备条件为：基膜中Armos的共混含量为4%、水相单体浓度为3%、油相单体浓度为0.15%时，制得的中空纤维复合纳滤膜性能最佳，其通量为8.40L/(m²·h)，对MgSO₄的截留率为88%。     

抗污染PVA/PVDF电纺纳米纤维复合超滤膜的制备及过滤性能

以聚对苯二甲酸二醇酯(PET)无纺布为基底,聚偏氟乙烯(PVDF)纳米纤维为支撑层,聚乙烯醇(PVA)纳米纤维膜为分离层,采用静电纺丝法制备超滤膜,并用水/丙酮混合溶液对复合纳米纤维膜表面进行溶液处理,再加入戊二醛交联改性得到致密分离层.采用扫描电子显微镜(SEM)和红外光谱(FTIR)表征了复合超滤膜的表面,用水接触角(WCA)表征复合超滤膜的亲水性.在0.02 MPa恒压下死端过滤油/水乳液,测试复合超滤膜的过滤性能.结果表明,最优条件下制备的复合超滤膜死端过滤油/水乳液的通量为(42.50±4.78)L/(m~2·h),截留率达到(95.72±0.33)%;循环使用5次后,依然具有较好的过滤性能,常压下死端过滤复合超滤膜的纯水通量为(3469±28)L/(m~2·h).     

低截留分子量PPES超滤膜的制备

以杂萘联苯聚醚砜(PPES)为膜材料、N-甲基吡咯烷酮(NMP)为溶剂、有机小分子丙醇(PrOH)和无机小分子氯化锂(LiCl)作为混合添加剂,采用相转化法制备超滤膜.研究了聚合物浓度、混合添加剂配比、凝胶浴温度等对膜结构和性能的影响.结果表明:随聚合物浓度的增大,膜的纯水通量下降,截留率升高;混合添加剂,在PrOH含量为12%、LiCl含量为1.5%时,可制得纯水通量为252 L/(m2·h),对聚乙二醇1000(PEGl000)截留率为96%的超滤膜;随凝胶浴温度的升高,膜的纯水通量增加.     

抗油污染α-纤维素中空纤维超滤膜油-水分离性能的研究

以α-纤维素为原料,一水合N-甲基吗琳-N-氧化物(NMMO.H2O)为溶剂,聚乙二醇(PEG400)为添加剂,去离子水为内外凝胶浴,采用浸入相转化法制备用于油水分离的中空纤维非对称超滤膜,并采用纯水通量表征了膜的性能.用纤维素中空纤维超滤膜进行油水分离实验,油水乳液的截留率可达到99%以上,渗透液含油量小于10 mg/L,达到国家环境保护排放要求.考察了物理清洗、物理清洗加0.1 mol/L HCL清洗、物理清洗加0.1 mol/L NaOH清洗3种清洗方法对油水污染后膜的清洗效果.其中,物理清洗加0.1 mol/LNaOH清洗的清洗方法的通量恢复率达到99%.与其它种类的膜相比,α-纤维素中空纤维膜的油水通量衰减率仅为9.5%,表现出优异的抗油污染性能.     

新型抑菌聚砜超滤膜的制备及性能

将辣素功能结构单体N-(4-羟基-3-甲氧基苯甲基)丙烯酰胺(HMBA)和甲基丙烯酸甲酯(MMA)通过自由基引发合成出抑菌型共聚物P(H-co-M), 通过红外吸收光谱和热重分析证实了共聚物的结构. 采用共混法将共聚物引入聚砜(PSF)铸膜液中, 通过浸没沉淀相转化法制备了新型抑菌超滤膜. 考察了P(H-co-M)含量对超滤膜分离性能及抑菌性能的影响. 结果表明, 当P(H-co-M)质量分数为0.5%时, 超滤膜分离性能最佳, 对5 mg/L腐殖酸溶液的稳定水通量为122.2 L/(m2·h), 截留率为84.4%, 与未添加P(H-co-M)的超滤膜相比, 分别提高了19.2%和9.2%. 改性超滤膜具有较强的抑菌性能, 当P(H-co-M)含量为1.0%时, 抑菌率最大(约80.7%).     

聚偏氟乙烯-磺化聚醚砜相容性及其成膜性能

研究了聚偏氟乙烯(PVDF)-磺化聚醚砜(SPES)的相容性及其成膜性能.首先通过溶解度参数、粘度法和目测法研究共混溶液的相容性,接着采用浊度法测定了共混溶液的热力学性质,最后采用浸没沉淀法制备了共混膜并探讨了成膜性能.结果显示,PVDF和SPES为部分相容体系,随着SPES含量的增加,共混溶液相容性逐渐减小,当SPES含量增加到50wt%时,体系发生分相.共混溶液的成膜性能良好,SPES含量增加有利于体系发生液液分相,生成高孔隙率膜,并且极大的提高了PVDF膜的亲水性和水通量.     

纳米储能纤维复合过滤膜的制备及性能

以静电纺丝技术制备的同轴聚甲基丙烯酸十八烷基酯(PSMA)/聚对苯二甲酸乙二酯(PET)纳米储能纤维为支撑层,经聚偏氟乙烯(PVDF)涂覆成膜和溶剂化处理,制备了一种低压高水通量的纳米储能纤维复合过滤膜(NFCM),其中以水或乙醇为凝固溶液的复合过滤膜分别记为NFCM@H2O或NFCM@EtOH.分析并讨论了不同溶剂处理方式对NFCM力学性能和表面形貌的影响,表征了膜的纯水通量和抗污性能,用扫描电子显微镜(SEM)观察了膜的横断面形貌.结果表明,PSMA/PET纳米储能纤维具有明显的吸放热行为,熔融温度和热焓值分别为36.5℃和10.7J/g,NFCM的熔融温度和热焓值分别为36℃和2.7J/g.NFCM的形貌结构、纯水通量和截留率与溶剂处理方式相关,NFCM@EtOH膜的水通量介于100~1400L/(m2·h)之间,而NFCM@H2O膜的水通量仅在40~220L/(m2·h)之间.NFCM的拉伸强度由初始0.925MPa(PVDF)提高到4.28MPa以上.NFCM中的相变材料对膜过滤性能有重要影响,并在过滤温度低于50℃时具有减缓作用.     

酚酞型聚醚砜(PES-C)超滤膜的制备及性能北大核心CSCD

以聚乙烯吡咯烷酮(PVP)和乙醇(EtOH)为添加剂,采用相转化法制得了酚酞型聚醚砜(PES-C)超滤膜。结果表明:当以乙醇为添加剂时,随着乙醇含量的增加,膜上表面变为致密结构,下表面呈多孔结构,水通量先上升后减小;当以PVP为添加剂时,随着PVP含量增加,PES-C膜的指状孔得到发展,膜通量和截留率都上升,当PVP的质量含量为10%时,PES-C膜的通量达到134.3L/(m2.h),对牛血清蛋白的截留率达85.1%。     

荷电膜的膜电位研究进展

膜电位的测定是表征荷电膜的传递现象的重要参数之一。本文简要介绍了膜电位理论基础,包括T. M. S.理论和不可逆热力学理论。分别阐述了关于离子交换膜、双极膜、两性膜以及复合膜的膜电位的最新进展,并提出今后的发展方向。     

高分子纳滤膜的研究及进展

对高分子纳滤膜的发展背景以及国内外在这一领域的研究的研究进展作了详细的介绍。     

纳米复合膜在膜分离领域的研究进展

基于纳米材料的独特性质,将其引入高分子膜所制得的纳米复合滤膜有望解决目前制约膜技术发展的“上限平衡”问题。 本文综述了碳纳米管、石墨烯、SiO2、TiO2、分子筛、ZrO2以及纳米银颗粒等纳米复合膜在膜分离领域的研究进展。 这些纳米材料对于提高复合膜的机械稳定性、亲水性、选择性、渗透性及抗污染能力等有显著的效果。 此外,对纳米复合膜的发展与应用做了展望,也对其研究中存在的问题和解决方法进行了阐述。     

Preparation of Zeolite X Membranes on Porous Ceramic Substrates with Zeolite Seeds

Zeolite X membranes were investigated by in-situ hydrothermal synthesis on porous ceramic tubes precoated with zeolite X seeds or precursor amorphous aluminosilicate, and porous α-Al2O3 ceramic tubes with a pore size of 50 200 nm were employed as supports. Zeolite X crystals were synthesized by the classic method and mixed into deionized water as a slurry with a concentration of 0.2 0.5wt%, having a range of crystal sizes from 0.2 to 2μm. Crystal seeds were pressed into the pores near the inner surface of the ceramic tubes, and crystallization took place at 95℃ for 24-96 h. It was also investigated that Boehmite sol added with zeolite X seeds was precoated on ceramic supports to form a layer of γ-Al2O3 by heating, and hydrothermal crystallization could then take place to prepare the zeolite membranes on the composite ceramic tubes. The crystal species were characterized by XRD, and the morphology of the supports subjected to crystallization was characterized by SEM. The composite zeolite membranes have zeolitic top-layers with a thickness of 10-25 μm, and zeolite crystals can be intruded into pores of the supports as deeply as 100μm. The experimental results indicate that the precoating of zeolitic seeds on supports is beneficial to crystallization by shortening the synthesis time and improving the membrane strength. The resulting zeolite X membrane shows permselectivity to tri-n-butylamine((C4H9)3N) over perfluro-tributyl-amine ((C4Fg)3N), and a permeance ratio of 57 for ((C4Hg)3N to (C4F9)3N could be reached at 350℃. Permeances of BZ, EB and TIPB through the zeolite membrane were also measured and were found to slightly increase with temperature.     

Theoretical analysis of the performance of composite membrane consisting of the catalytic and nanofiltration layers

A model of the composite membrane consisting of the catalytic layer (CL) and the nanofiltration layer (NFL) is presented. It has been found that applying NFL on the permeate side of CL it is possible to enhance substantially the conversion of substrate into the product. The best performance is obtained for high retention of substrate and low of product. At higher values of volume flow and/or longer catalytic path the retention degree of product becomes negligible. The presence of NFL enhances the influence of distribution of the reaction rate constant, k, on the conversion ratio. Comparing to k = constant the positive effect is obtained if k increases along the catalytic pore, whereas negative—if k decreases.     

Preparation of Zeolite X Membranes on Porous Ceramic Substrates with Zeolite Seeds

Zeolite X membranes were investigated by in-situ hydrothermal synthesis on porous ceramic tubes precoated with zeolite X seeds or precursor amorphous aluminosilicate, and porous α-Al2O3 ceramic tubes with a pore size of 50-200 nm were employed as supports. Zeolite X crystals were synthesized by the classic method and mixed into deionized water as a slurry with a concentration of 0.2-0.5wt%, having a range of crystal sizes from 0.2 to 2μm. Crystal seeds were pressed into the pores near the inner surface of the ceramic tubes, and crystallization took place at 95℃ for 24-96 h. It was also investigated that Boehmite sol added with zeolite X seeds was precoated on ceramic supports to form a layer of r-Al2O3 by heating, and hydrothermal crystallization could then take place to prepare the zeolite membranes on the composite ceramic tubes. The crystal species were characterized by XRD, and the morphology of the supports subjected to crystallization was characterized by SEM. The composite zeolite membranes hav     

氯化锂为添加剂制得的疏水聚偏氟乙烯不对称微孔膜的形态结构及其膜蒸馏性能

结合膜的形态结构研究了以 LiCl为添加剂制得的疏水 PVDF膜的膜蒸馏性能。与来用水溶液高分子添加剂制得的PVDF微孔膜相比,膜蒸馏性能有了较大提高,尤其具有更高的截留率。制得的微孔膜的蒸馏通量已接近商品膜的膜蒸馏通量,表明以LiCl为添加剂制得的PVDF疏水微孔膜是一种适用于膜蒸馏的较理想的疏水微孔膜。     

透氢钯复合膜的原理、制备及表征

钯及其合金膜由于具有透氢性好和耐高温的特点,除了用作氢气分离和纯化器外,还可以用作脱氢、制氢等反应的反应器,以实现反应和分离的一体化,并提高转化率和选择性。本文综述了钯基复合膜的原理、制备及表征,并重点介绍了本研究组的光催化镀膜工艺。     

两种固定化金属螯合复合亲和膜色谱介质制备

以纤维素滤纸为基质,通过碱处理、环氧活化、偶联亚氨基二乙酸二钠、固定化Ｃｕ＾２＋后制得了大孔纤维素亲和膜。另外,在活化后的膜上通过共价交联覆盖上琼脂糖,制得了具有类似“三明治”结构且性能优于的复合亲和膜,装柱后分别制得固定化金属螯合亲和膜色谱柱。对两种亲和膜进行牛血清白蛋白等温吸附测定显示,两者的最大吸附量分别为１．１７ｍｇ／ｃｍ＾２和１．３０ｍｇ／ｃｍ＾２,与传统的琼脂糖凝胶类介质吸附量相当,表     

透氢钯复合膜的原理、制备及表征

钯及其合金膜由于具有透氢性好和耐高温的特点,除了用作氢气分离和纯化器外,还可以用作脱氢、制氢等反应的反应器,以实现反应和分离的一体化,并提高转化率和选择性。本文综述了钯基复合膜的原理、制备及表征,并重点介绍了本研究组的光催化镀膜工艺。