蛭石负载TiO2光催化剂的制备与性能

以新疆尉犁工业蛭石为载体,采用溶胶-凝胶法制备负载型二氧化钛光催化剂,利用XRD、TG、SEM、IR和低温N₂吸附－脱附对负载型二氧化钛进行表征,并以亚甲基蓝为目标降解物对其光催化性能进行研究。讨论了不同TiO₂负载量、反应温度和煅烧温度等因素对负载型二氧化钛光催化性能的影响,结果表明：TiO₂负载量为4.0wt%,反应温度为40 ℃,煅烧温度为400 ℃时,复合材料光催化效果最好,经60 W紫外灯照射20 min后,TiO₂/VMT复合材料对亚甲基蓝溶液的降解率为92.08%。     

Fe2O3/TiO2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO₂纳米管阵列,采用化学浴方法在TiO₂纳米管阵列上修饰了Fe₂O₃纳米颗粒.利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能.结果表明,Fe₂O₃纳米颗粒的修饰将TiO₂纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe₂O₃/TiO₂纳米管阵列的光电流是未修饰的TiO₂纳米管阵列的9倍.而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO₂纳米管阵列高出30%.     

阳极氧化法制备TiO2纳米管及其光催化性能

纳米TiO₂对诸多环境污染物有显著的光催化降解作用,光催化已发展成为新型环境污染治理技术。本文采用阳极氧化法制备出TiO₂纳米管,对比了四种电解液组成(A氟化铵+硫酸铵+水;B氟化铵+硫酸铵+乙酸+水;C氟化铵+硫酸铵+甘油+水;D氢氟酸+二甲基亚砜(DMOS)+乙醇)对催化剂表面形貌及光催化性能的影响。结果表明,电解液A和C都制备出了形貌清晰的TiO₂纳米管,管径约为60~74 nm。样品经400 ℃煅烧,TiO₂晶型主要为锐钛矿相;经500 ℃煅烧,出现少量金红石相;经700 ℃煅烧,晶型全部为金红石相。具有良好形貌的TiO₂纳米管同时具有良好的紫外光吸收能力。当亚甲基蓝初始浓度为10 mg·L^-1,经500 ℃煅烧的TiO₂纳米管光催化活性最佳,光照30 min亚甲基蓝的降解率达89.98%。亚甲基蓝光催化降解反应符合一级反应动力学,反应速率常数为0.079 30。     

中空Ta2O5/TiO2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC₂纳米碳化物涂层,并以所得TaTiC₂/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta₂O₅/TiO₂复合光催化剂。采用X射线粉末衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、紫外-可见（UV-Vis）漫反射（DRS）及N₂物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta₂O₅/TiO₂复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀（20~30 nm）,碳化物主要以TaTiC₂晶相存在且具有纳米级的颗粒尺寸。中空Ta₂O₅/TiO₂复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO₂与Ta₂O₅通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。n_Ti∶n_Ta=2.5∶1.5时,相应的中空Ta₂O₅/TiO₂复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

双介孔结构的纳米TiO2/I2复合材料的制备及其可见光催化性能

以钛酸丁酯为前驱体, 碘溶胶为碘源, 在室温下采用水解沉淀法制备了单质碘和纳米TiO₂复合的双介孔结构光催化剂(M-I₂-TiO₂). 采用X射线衍射(XRD)、透射电子显微镜(TEM)、比表面分析(BET)、紫外-可见(UV-Vis)漫反射光谱和傅里叶变换-红外光谱(FT-IR)对M-I₂-TiO₂进行了表征. 以次甲基蓝(MB)溶液为模拟废水, 对M-I₂-TiO₂的光催化性能进行了评价, 研究了不同热处理温度对光催化活性的影响. 结果表明, M-I₂-TiO₂在可见光区有显著的吸收, 300 ℃热处理得到的样品比表面积高达227.6 m²/g, 600 ℃热处理所得样品的比表面积仍高达111.8 m²/g, 而400 ℃热处理所得样品具有最好的光催化降解性能. 双介孔结构纳米TiO₂/I₂复合材料的光催化降解性能显著高于相同方法制备的纯TiO₂和Degussa P-25商业产品. 催化剂经6次重复使用其光催化活性基本保持不变.     

有机改性TiO2光催化剂的制备及可见光催化性能

以染料黄叱精(Chrysoidine G)和TiO₂ (Degussa P25)为原料, 利用甲苯二异氰酸酯为桥连体, 成功合成了一种有机改性的TiO₂光催化剂. 采用XRD, TEM, FT-IR, UV-Vis对所得催化剂进行了表征, 以亚甲基蓝降解为探针反应, 考察其可见光催化性能. 结果表明: 甲苯二异氰酸酯在黄叱精和TiO₂之间形成了稳定的化学键, 从而实现了对TiO₂的表面有机改性; 改性后的TiO₂在可见光区(400～550 nm)有明显的吸收; 与未改性TiO₂相比, 有机改性的TiO₂催化剂在可见光照射下表现出了很好的光催化性能.     

磁载光催化剂TiO2/SiO2/Ni0.5Fe2.5O4的制备及其催化氧化性能

采用固相反应法制备磁载体(SiO₂/Ni_0.5Fe_2.5O₄),溶胶-凝胶法得到易于磁分离回收的磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄。用XRD、SEM、IR和UV-Vis等进行表征。研究了太阳光下催化剂对亚甲基蓝溶液的脱色性能。结果表明,在太阳光下,磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄可使亚甲基蓝溶液迅速脱色；3次循环使用后脱色率仍为95%以上,回收率为98.8%。     

Ag3PO4/MoS2纳米片复合催化剂制备及可见光催化性能

采用机械球磨法成功制备Ag₃PO₄/MoS₂纳米片复合催化剂。运用X射线衍射仪（XRD）、透射电子显微镜（TEM）、扫描电子显微镜（SEM）、紫外可见漫反射光谱（UV-Vis）和荧光发射光谱（PL）对复合催化剂的结构和形貌进行了表征。结果表明,Ag₃PO₄纳米粒子均匀地附着在MoS₂纳米片层结构上,两者形成紧密结合。以亚甲基蓝为模拟污染物,研究复合催化剂在可见光照射下的光催化特性;通过循环实验考察复合催化剂的稳定性。结果显示,含有1%的MoS₂纳米片与Ag₃PO₄形成的复合催化剂在30 min内对亚甲基蓝的降解率为95%,其降解动力学常数是纯相Ag₃PO₄的2倍。经过5次循环实验后复合催化剂对于亚甲基蓝的降解率为84%,而纯Ag₃PO₄对于亚甲基蓝的降解率仅为35%。Ag₃PO₄/MoS₂纳米片复合催化剂具有优良的光催化活性和高稳定性,主要归因于二硫化钼纳米片与磷酸银形成异质结,磷酸银激发的电子和二硫化钼纳米片产生的空穴直接复合,从而促使光生电子从磷酸银晶体表面快速分离,减轻了磷酸银的光电子腐蚀,同时也提高了复合物的光催化活性。     

TiO2/Gd2O3纳米粉体的制备、表征及光催化活性

利用酸催化的溶胶-凝胶法制备了纯TiO₂和Gd³⁺(0.5wt%)掺杂的TiO₂纳米粉体，采用XRD、BET、XPS、紫外-可见漫反射谱(DRS)和表面光电压谱(SPS)等技术进行了表征；以亚甲基蓝(MB)的光催化降解为探针反应，评价了其光催化活性；探讨了Gd³⁺掺杂对TiO₂纳米粉体的光催化活性的影响机制。结果表明，TiO₂/Gd₂O₃纳米粒子对MB溶液的光催化活性提高到纯TiO₂的1.5倍。掺杂Gd³⁺可以强烈抑制TiO₂由锐钛矿相向金红石相的转变；阻碍TiO₂晶粒的生长；提高高温组织稳定性，改善粉体的表面织构特性；形成光生电子的浅势捕获陷阱，抑制e^-/h⁺复合，这些因素共同作用最终导致TiO₂/Gd₂O₃纳米粉体的光催化活性明显提高。XPS分析结果证实，掺杂Gd³⁺导致粉体的表面羟基含量降低。由于产生了量子尺寸效应，复合粉体的紫外吸收带边蓝移，光的吸收能力略有降低。     

载有C60的TiO2纳米粒子光催化活性

以水溶性C₆₀和TiO₂粒子为前驱体,采用水热法制备了载有C₆₀的锐钛矿型TiO₂纳米粒子。应用X射线衍射、透射电子显微镜、红外光谱、紫外-可见漫反射光谱、荧光光谱对产物进行了表征。以对-硝基苯酚为模型污染物研究了产物的光催化活性,结果表明适量负载C₆₀可以提高TiO₂纳米粒子的光催化活性,C₆₀起着传输电子、促进TiO₂光生载流子分离的作用,且经7次循环使用后对-硝基苯酚的降解效率仍能达到74%。讨论了载有C₆₀的TiO₂纳米粒子光催化降解对-硝基苯酚的机理。     

SiO2/TiO2-xCx/C的制备、表征及其吸附和可见光催化性能

以SiO2为成核中心,钛酸四丁酯为钛源,分别以多羟基化合物乙二醇、丙三醇、葡萄糖和聚乙烯醇为联接剂,采用水解沉淀法制备了碳掺杂和包覆的多孔SiO2/TiO2-xCx/C可见光响应型光催化剂。采用X-射线衍射(XRD)、透射电子显微镜(TEM)、X-射线光电子能谱(XPS)、傅里叶变换-红外光谱(FTIR)、比表面积(BET)和紫外-可见(UV-Vis)漫反射光谱对样品进行表征。对不同结构样品的形成机理进行了分析。以次甲基蓝(MB)溶液为模拟废水,对样品的吸附性能和可见光催化性能进行了评价。结果表明,多羟基化合物对材料的结构和性能有重要影响。碳的掺杂和包覆使材料的吸收光谱包含了整个可见光区,而多孔结构使材料的吸附性能得到提高。以聚乙烯醇为原料所得样品吸附性能最好,30 min内吸附率达到70%;而以丙三醇为原料所得样品具有最好的可见光催化性能,40 min内次甲基蓝的降解率达到95%。     

可见光下具有高光子效应和光催化活性的CuS-石墨烯氧化物/TiO2复合材料的制备（英文）

CuS-graphene oxide/TiO2 composites were prepared using a sol-gel method to improve the photocatalytic performance of the photocatalyst. The composites were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The photocatalytic activities were examined by the degradation of methylene blue (MB) under visible-light irradiation. The photodegradation of MB under visible-light irradiation reached 90.1% after 120 min. The kinetics of MB degradation was plotted alongside the values calculated from the Langmuir-Hinshelwood equation. The CuS-graphene oxide/TiO2 sample prepared using 0.2 mol of TiO2 showed the best photocatalytic activity. This was attributed to a cooperative reaction as a result of increased photoabsorption by graphene oxide and an increased photocatalytic effect by CuS.     

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin,TiO2/diatomite,and TiO2/zeolite

Three TiO₂ loaded composites, TiO₂/kaolin, TiO₂/diatomite, and TiO₂/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO₂. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO₂ content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.     

Synthesis of CuAPTPP-TDI-TiO2 Conjugated Microspheres and its Photocatalytic Activity (cited: 1)

The metal complex 5-(4-aminophenyl)-10,15,20-triphenylporphyrin copper (CuAPTPP) was covalently linked on the surface of TiO₂ microspheres by using toluene disocyanate (TDI) as a bridging bond unit. The hydroxyl group (-OH) of TiO₂ microspheres surface and the amino group (-NH₂) of CuAPTPP reacted respectively with the active -NCO groups of TDI to form a surface conjugated microsphere CuAPTPP-TDI-TiO₂ that was confirmed by FT-IR spectra. The CuAPTPP-TDI-TiO₂ microspheres were characterized with UV-visible, elemental analysis, XRD, SEM, and UV-Vis diffuse reflectance spectra. The effect of amounts of linked TDI on the performance of photocatalytic microspheres was discussed, and the optimal molar ratio of TDI:TiO₂ was established. The photocatalytic activity of CuAPTPP-TDI-TiO₂ was evaluated using the photocatalytic degradation of methylene blue (MB) under visible-light irradiation. The results showed that, TDI, as a bond unit, was used to form a steady chemical brigdging bond linking CuAPTPP and the surface of TiO₂ microspheres, and the prepared catalyst exhibited higher photocatalytic activity under visible-light irradiation for MB degradation. The degradation rate of 20 mg/L MB could reach 98.7% under Xe-lamp (150 W) irradiation in 120 min. The degradation of MB followed the first-order reaction model under visible light irradiation, and the rate constant of 5.1×10^-2 min^-1 and the half-life of 11.3 min were achieved. And the new photocatalyst can be recycled for 4 times, remaining 90.0% MB degradation rate.     

中空Ta_2O_5/TiO_2复合光催化剂的可控氧化制备及性能

以钛粉、钽粉为原料,炭黑作为反应性模板,通过熔盐法在炭黑表面原位生长了TaTiC_2纳米碳化物涂层,并以所得TaTiC_2/C复合物为碳化物前驱体,再经可控氧化制备出中空Ta_2O_5/TiO_2复合光催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见(UV-Vis)漫反射(DRS)及N2物理吸附等手段对所制备的光催化剂进行形貌、显微结构及孔结构表征。以高压汞灯为紫外光源,以亚甲基蓝为目标降解物,通过光催化降解实验评价中空Ta_2O_5/TiO_2复合光催化剂的光催化活性。结果表明,熔盐法生长碳化物涂层厚度均匀(20~30 nm),碳化物主要以TaTiC_2晶相存在且具有纳米级的颗粒尺寸。中空Ta_2O_5/TiO_2复合光催化剂同时具有200 nm左右的中空大孔结构及壳层10 nm左右的介孔结构。中空大孔和介孔的存在提高了所制备催化剂对亚甲基蓝的吸附能力。此外,TiO_2与Ta2O5通过电子能带结构的耦合,有效提高了光生电子和空穴的分离效率,从而显著提高了光催化活性。nTi∶nTa=2.5∶1.5时,相应的中空Ta_2O_5/TiO_2复合光催化剂表现出最佳的光催化活性,对亚甲基蓝的紫外光催化降解率高达97%。     

Photocatalytic Degradation of Organic Reactive Dyes over MnTiO3/TiO2 Heterojunction Composites Under UV‐Visible Irradiation

In this study, the photocatalytic degradation of organic reactive dyes have been investigated using MnTiO₃/TiO₂ heterojunction composites in the presence of electron acceptors under UV‐Visible light irradiation. This MnTiO₃/TiO₂ heterojunction composites were prepared by annealing different mass ratios of pyrophanite MnTiO₃ (3–11 wt%) and TiO₂ at 300°C. All the MnTiO₃/TiO₂ heterojunction composites were characterized by spectral techniques like X‐ray diffraction (XRD), scanning electron microscope (SEM) and diffused reflectance UV‐visible spectroscopic analysis (DRS). Among them, 9 wt% MnTiO₃/TiO₂ heterojunction composites exhibited higher photocatalytic activity for the degradation of Reactive Blue 4 (RB 4). The photocatalytic efficiency of 9 wt% MnTiO₃/TiO₂ heterojunction composites was further enhanced by the addition of substantial amount of electron acceptors like hydrogen peroxide (H₂O₂) and ammonium peroxydisulfate ([NH₄]₂S₂O₈). The presence of oxidants (electron acceptors) facilitates the fast degradation of dye solution even in higher concentration upto 200 mg/L. The photocatalytic activity of MnTiO₃/TiO₂ heterojunction composites was also studied for the degradation of other four different structured reactive dyes. The extent of mineralization of these organic reactive dyes during photocatalytic degradation was estimated from COD analysis. MnTiO₃/TiO₂ heterojunction composites was also found to have good photostability in the presence of oxidants.     

TiO2/BiVO4, a Heterojuncted Microfiber with Enhanced Photocatalytic Performance for Methylene Blue under Visible Light Irradiation

Novel TiO₂/BiVO₄ microfiber heterojunctions were constructed using cotton as biomorphic templates. The as-synthesized samples were characterized by scanning electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy, UV-Vis diffuse reflectance spectra and photocatalytic experiment. The morphology of the as-synthesized TiO₂/BiVO₄ composites was consisted of a large quantity of microfiber structures with diameter from 2.5 μm to 5 μm, and the surface of samples became more coarse and compact with the increase of weight ratio of TiO₂. The TiO₂/BiVO₄ samples with proper content (10.00wt%) showed the highest pho-tocatalytic degradation activity for methylene blue (MB) degradation among all the samples under visible light, and 88.58%MB could be degraded within 150 min. The enhancement of photocatalytic activity was mainly attributed to the formation of n-n heterojunction at the contact interface of TiO₂ and BiVO₄, which not only narrowed the band gap of BiVO₄ for extending the absorption range of visible light, but also promoted the transfer of charge carriers across interface. A possible photodegradation mechanism of MB in the presence of TiO₂/BiVO₄ microfibrous photocatalyst was proposed.     

GO/TiO2-g-C3N4纳米复合材料的制备及可见光催化性能

以水热法制备的20% g-C₃N₄/TiO₂（20%为质量分数）为基,将其与不同质量分数的氧化石墨烯（GO）复合制备出可见光催化性能优良的GO/TiO₂-g-C₃N₄三元复合材料。利用X射线衍射（XRD）、扫描电子显微镜（SEM）、X射线光电子能谱（XPS）、紫外-可见漫反射光谱（UV-Vis DRS）、光致荧光光谱（PL）、瞬态光电流响应等分析测试手段对样品的结构、形貌和光电性能进行表征。研究了不同质量分数GO的加入对GO/TiO₂-g-C₃N₄在可见光下降解亚甲基蓝（MB）溶液的影响。结果表明： g-C₃N₄/TiO₂与GO复合后,锐钛矿相TiO₂颗粒形成小团簇附着在g-C₃N₄和GO片层表面,且当GO含量为15%时,TiO₂形成的团簇最小,对可见光的吸收最多且光生电子-空穴对的复合率最低。可见光照射下,15% GO/TiO₂-g-C₃N₄复合材料对MB的降解率在3 h内可达98.4%,且其降解速率常数（0.022 4 min^-1）分别是纯TiO₂（0.001 5 min^-1）和g-C₃N₄/TiO₂（0.002 5 min^-1）的15倍和9倍。     

Characterization, activity and mechanisms of a visible light driven photocatalyst: Manganese and iron co-modified TiO2 nanoparticles

An attempt was made to prepare Mn,Fe-codoped nanostructured TiO₂ photocatalyst for visible light assisted degradation of an azo dye (methylene blue) in aqueous solutions by a sol-gel process. The asprepared nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and photoluminescence spectra (PL) techniques. The photocatalytic activity of Mn,Fe-codoped TiO₂ catalyst was evaluated by measuring degradation rates of methylene blue (MB) under visible light. The results showed that doping with the manganese and iron ions significantly enhanced the photocatalytic activity for MB degradation under visible light irradiation. This was ascribed to the fact that a small amount of manganese and iron dopants simultaneously increased MB adsorption capacity and separation efficiency of electron-hole pairs. The results of DRS showed that Mn,Fe-codoped TiO₂ had significant absorption between 400 and 500 nm, which increased with the increase of manganese ion content. It is found that the stronger the PL intensity, the higher the photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions, so that the recombination of photoinduced electrons and holes could be effectively inhibited.