The crystallographic texture and magnetic anisotropy of melt-spun CeCo5.4 ribbon

CeCo_5.4 ribbons have been prepared by melt spinning at wheel speeds v=5, 15, 25 and 35 m/s. The ribbons are essentially single 1:5 phase, and have significant crystallographic texture and magnetic anisotropy. The ribbon's longitudinal direction is easy direction, and normal to the ribbon plane direction is hard direction. For v=5 m/s [1 1 1]-axes of the grains near non-contact surface of the ribbon are normal to the ribbon plane. With increase of v, [1 1 0] and [2 0 0]-axes of the grains near non-contact surface rotate toward the normal direction and the c-axes parallel to the ribbon plane. The anisotropy increases up to v=25 m/s and then decreases. The grains near contact-wheel surface are randomly oriented for all v. The coercivity increases with increase of v due to decrease of the grain size. The values of coercivity are smaller in the easy direction and are larger in the hard direction, meaning that the coercivity mechanism is mainly characterized by domain wall pinning.     

The superconducting properties of Cu-doped MgB2 bulks prepared by a high-energy milling method

The Cu-doped MgB₂ bulks were prepared by a high-energy milling and subsequent sintering method. Compared to the pure and Cu-doped bulks prepared only by sintering, the critical current density (J_c) of the milled Cu-doped samples was improved with a slight decrease in critical transition temperature (T_c). Using the phase analysis and microstructure observation, it has been found that the MgB₂ grains in the milled Cu-doped sample was refined with the high-energy milling and thus provided more grain boundary pinning, which was contributed to the improvement of J_c at high field.     

High heat generation ability in AC magnetic field for nano-sized magnetic Y3Fe5O12 powder prepared by bead milling

Nano-sized magnetic Y₃Fe₅O₁₂ ferrite having a high heat generation ability in an AC magnetic field was prepared by bead milling. A commercial powder sample (non-milled sample) of ca. 2.9 μm in particle size did not show any temperature enhancement in the AC magnetic field. The heat generation ability in the AC magnetic field improved with a decrease in the average crystallite size for the bead-milled Y₃Fe₅O₁₂ ferrites. The highest heat ability in the AC magnetic field was for the fine Y₃Fe₅O₁₂ powder with a 15-nm crystallite size (the samples were milled for 4 h using 0.1 mm? beads). The heat generation ability of the excessively milled Y₃Fe₅O₁₂ samples decreased. The main reason for the high heat generation property of the milled samples was ascribed to an increase in the Néel relaxation of the superparamagnetic material. The heat generation ability was not influenced by the concentration of the ferrite powder. For the samples milled for 4 h using 0.1 mm? beads, the heat generation ability (W g⁻¹) was estimated using a 3.58×10⁻⁴ fH² frequency (f/kHz) and the magnetic field (H/kA m⁻¹), which is the highest reported value of superparamagnetic materials.     

Preparation of α-Fe2O3 nanoparticles by high-energy ball milling

α-Fe₂O₃ nanoparticles were prepared by high-energy ball milling using α-FeOOH as raw materials. The prepared samples were characterized by transmission electron microscopy (TEM), Mössbauer spectroscopy, X-ray diffraction (XRD) and differential thermal analysis–thermogravimetric analysis (DTA–TGA). The results showed that after 90 h milling α-Fe₂O₃ nanoparticles were obtained, and the particle size is about 20 nm. The mechanism of reaction during milling is supposed that the initial α-FeOOH powder turned smaller and smaller by the high-speed collision during ball milling, later these particles turned to be superparamagnetic, at last these superparamagnetic α-FeOOH particles were dehydrated and transformed into α-Fe₂O₃.     

Microstructure and magnetic properties studies of SmCo5 thin films grown on MgO and glass substrates

In this work, SmCo₅ thin films are deposited on single crystal MgO (1 0 0) and amorphous glass substrates with a Cr underlayer at 400 °C by sputtering. A comparison study shows that the microstructures and magnetic properties are different in the two SmCo₅ films on the MgO (1 0 0) and glass substrates, respectively. An epitaxial growth of Cr-(2 0 0)〈1 1 0〉/SmCo₅-(1 1 2¯ 0)〈0 0 0 1〉 is achieved on the MgO (1 0 0) single crystal substrate with an average grain size of 20 nm for SmCo₅. On the amorphous glass substrate, no significant crystallographic texture is found in the Cr underlayer. After the deposition of SmCo₅, a weak texture of (1 1 2¯ 0) is observed with an average grain size of 8 nm. High remanence ratio value in this film is probably due to strong exchange coupling. Both SmCo₅ films show high in-plane coercivity, high in-plane anisotropy and remanence enhancement.     

Probing the anisotropy constants of SmCo5 and PrCo5 by Hall resistance measurements in pulsed high magnetic fields up to 47 T

In order to assess the anisotropy constants of highly anisotropic thin film samples with anisotropy fields well above 10 T, Hall resistance measurements were conducted in pulsed magnetic fields. These measurements also deliver the anomalous Hall data, which are proportional to the perpendicular magnetisation. This specific approach combines the high field values obtainable by pulsed fields with a measurement technique sensitive enough to be applied to thin film samples. Two epitaxial Rare Earth-Cobalt thin films with large in-plane uniaxial magnetocrystalline anisotropy at room temperature were studied. The resulting anisotropy fields and constants are discussed with respect to measurements on single crystals and similar films investigated in quasi-static magnetic fields well below the anisotropy field. The present technique proved to be very valuable to highly anisotropic samples, as the approach to saturation is fully monitored and the data thus provides a more extended view on the hard axis magnetisation process.     

A study on magnetic properties and structure of SmCo5 thin films on Ni-W underlayers

A systematic study on Ni-W alloy underlayers has shown that a highly textured (2 1 1)-Ni₄W can be formed after deposition at room temperature. Highly textured (0 0 0 1)-SmCo₅ with a high out-of-plane coercivity (over 10 kOe) and large perpendicular anisotropy can be obtained after deposition on the (2 2 1)-Ni₄W underlayer probably due to a small mismatch between (2 2 1)-Ni₄W and (0 0 0 1)-SmCo₅. Our study indicates that the surface roughness of the underlayers also plays a crucial role, that a smooth surface is favorable for a good crystallinity and high coercivity of SmCo₅. Moreover, we found that a highly textured Ni-(1 1 1) can be obtained on the top of the (2 1 1)-textured Ni₄W. The film structure of SmCo₅/Ni/Ni₄W may be interesting as the hard/soft double-layered film for perpendicular magnetic recording or for other applications after a further development.     

Magnetic characterization of Mn5SiB2 and Mn5Si3 phases

In this work the Mn₅Si₃ and Mn₅SiB₂ phases were produced via arc melting and heat treatment at 1000 °C for 50 h under argon. A detailed microstructure characterization indicated the formation of single-phase Mn₅Si₃ and near single-phase Mn₅SiB₂ microstructures. The magnetic behavior of the Mn₅Si₃ phase was investigated and the results are in agreement with previous data from the literature, which indicates the existence of two anti-ferromagnetic structures for temperatures below 98 K. The Mn₅SiB₂ phase shows a ferromagnetic behavior presenting a saturation magnetization M_s of about 5.35×10⁵ A/m (0.67 T) at room temperature and an estimated Curie temperature between 470 and 490 K. In addition, AC susceptibility data indicates no evidence of any other magnetic ordering in 4-300 K temperature range. The magnetization values are smaller than that calculated using the magnetic moment from previous literature NMR results. This result suggests a probable ferrimagnetic arrangement of the Mn moments.     

Magnetoresistivity and microstructure of YBa2Cu3Oy prepared using planetary ball milling

We have studied the microstructure and the magnetoresistivity of polycrystalline YBa₂Cu₃O_y (YBCO or Y-123 for brevity) embedded with nanoparticles of Y-deficient YBCO, generated by the planetary ball milling technique. Bulk samples were synthesized from a precursor YBCO powder, which was prepared from commercial high purity Y₂O₃, Ba₂CO₃ and CuO via a one-step annealing process in air at 950 °C. After planetary ball milling of the precursor, the powder was uniaxially pressed and subsequently annealed at 950 °C in air. Phase analysis by X-ray diffraction (XRD), granular structure examination by scanning electron microscopy (SEM), microstructure investigation by transmission electron microscopy (TEM) coupled with energy dispersive X-ray spectroscopy (EDXS) were carried out. TEM analyses show that nanoparticles of Y-deficient YBCO, generated by ball milling, are embedded in the superconducting matrix. Electrical resistance as a function of temperature, ρ(T), revealed that the zero resistance temperature, T_co, is 84.5 and 90 K for the milled and unmilled samples respectively. The milled ceramics exhibit a large magnetoresistance in weak magnetic fields at liquid nitrogen temperature. This attractive effect is of high significance as it makes these materials promising candidates for practical application in magnetic field sensor devices.     

Study on dielectric and magnetic properties of Ho3Fe5O12 ceramics

Ho₃Fe₅O₁₂ ceramics with garnet structure were prepared by the solid-state reaction method. The results revealed the existence of Fe²⁺ ions have intensive influence on dielectric and magnetic properties of Ho₃Fe₅O₁₂ ceramics, which could be further confirmed by oxygen treatment. With a magnetic field lower than 10 kOe, the ME coefficient reaches 33 ps m⁻¹ at room temperature. And the ME coupling was further verified by dielectric anomaly near Néel temperature.     

Synthesis and magnetic properties of single-crystalline BaFe12O19 nanoparticles

Rod-like and platelet-like nanoparticles of simple-crystalline barium hexaferrite (BaFe₁₂O₁₉) have been synthesized by the molten salt method. Both particle size and morphology change with the reaction temperature and time. The easy magnetization direction (0 0 l) of the BaFe₁₂O₁₉ nanoparticles has been observed directly by performing X-ray diffraction on powders aligned at 0.5 T magnetic field. The magnetic properties of the BaFe₁₂O₁₉ magnet were investigated with various sintering temperatures. The maximum values of saturation magnetization (σ_s=65.8 emu/g), remanent magnetization (σ_r=56 emu/g) and coercivity field (H_ic=5251 Oe) of the aligned samples occurred at the sintering temperatures of 1100 °C. These results indicate that BaFe₁₂O₁₉ nanoparticles synthesized by the molten salt method should enable detailed investigation of the size-dependent evolution of magnetism, microwave absorption, and realization of a nanodevice of magnetic media.     

Effects of O2/Ar ratio and annealing temperature on electrical properties of Ta2O5 film prepared by magnetron sputtering

The effects of the oxygen-argon ratio on electric properties of Ta2O5 film prepared by radio-frequency magnetron sputtering were investigated.The Ta2O5 partially transforms from the amorphous phase into the crystal phase when annealing temperatures are 800℃ or higher.The lattice constant of Ta2O5 decreases with the increase of the O2/Ar ratio,which indicates that oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies during the deposition process.For the films deposited in working gas mixtures with different O2/Ar ratios and subsequently annealed at 700℃,the effective dielectric constant is increased from 14.7 to 18.4 with the increase of the O2/Ar ratio from 0 to 1.Considering the presence of an SiO2 layer between the film and the silicon substrate,the optimal dielectric constant of Ta2O5 film was estimated to be 31.Oxygen gas in the working gas mixture contributes to reducing the density of oxygen vacancies,and the oxygen vacancy density and leakage current of Ta2O5 film both decrease with the increase of the O2/Ar ratio.The leakage current decreases after annealing treatment and it is minimized at 700℃.However,when the annealing temperature is 800℃ or higher,it increases slightly,which results from the partially crystallized Ta2O5 layer containing defects such as grain boundaries and vacancies.     

Effect of Fe/Sr mole ratios on the formation and magnetic properties of SrFe12O19 microtubules prepared by sol-gel method

The sol was obtained by sol-gel method. Then, the sol was dripped onto the absorbent cotton template. The gel was obtained after the evaporation of water. Strontium ferrite microtubules were prepared after carrying out calcination process at different temperatures. The phase, morphology and particle diameter and the magnetic properties of samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM), respectively. The effects of Fe³⁺/Sr²⁺ mole ratio and calcination temperature on the crystal structure, morphology and magnetic properties of ferrite microtubules were studied. The external diameters of obtained SrFe₁₂O₁₉ microtubules were found to range between 8 and 13 μm; the wall thicknesses ranged between 1 and 2 μm. When the Fe³⁺/Sr²⁺ mole ratio and the calcination temperature were 11.5 and 850 °C, respectively, the coercivity, saturation magnetization and remanent magnetization for the samples were 7115.1 Oe, 70.1 and 42.4 emu/g, respectively. The mechanism of the formation and variation in magnetic properties of the microtubules were explained.     

Structural, optical and magnetic properties of Nd-doped BiFeO3 thin films prepared by pulsed laser deposition

Nd-doped BiFeO₃ thin films were grown by pulsed laser deposition on quartz substrate and their structural, optical and magnetic properties have been studied. X-ray diffraction analysis revealed that Nd addition caused structural distortion even with 5% of Nd concentration, additional secondary phase appeared in all samples but its intensity was greatly reduced with Nd addition. Doping-induced variations in texture and structure modifying both magnetic and optical properties of BiFeO₃ thin films. The energy band gap decreases while the refractive index increases with addition of Nd³⁺ in BiFeO₃ for Bi³⁺. These variations in energy band gap and refractive index have been explained on the basis of density of states and increase in disorders in the system. All the samples were found to exhibit ferromagnetism at room temperature and the saturation magnetization increases with the increase in structural distortion with addition of Nd. Finally, Nd-doping modifies the physical properties of BiFeO₃ in comparison to undoped BiFeO₃ thin films.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Biosynthesis and magnetic properties of mesoporous Fe3O4 composites

Magnetic Fe₃O₄ materials with mesoporous structure are synthesized by co-precipitation method using yeast cells as a template. The X-ray diffraction (XRD) pattern indicates that the as-synthesized mesoporous hybrid Fe₃O₄ is well crystallized. The Barrett-Joyner-Halenda (BJH) models reveal the existence of mesostructure in the dried sample which has a specific surface area of 96.31 m²/g and a pore size distribution of 8-14 nm. Transmission electron microscopy (TEM) measurements confirm the wormhole-like structure of the resulting samples. The composition and chemical bonds of the Fe₃O₄/cells composites are studied by Fourier transform infrared (FT-IR) spectroscopy. Preliminary magnetic properties of the mesoporous hybrid Fe₃O₄ are characterized by a vibrating sample magnetometer (VSM). The magnetic Fe₃O₄/cells composites with mesoporous structure have potential applications in biomedical areas, such as drug delivery.     

Heat generation ability in AC magnetic field of nano MgFe2O4-based ferrite powder prepared by bead milling

Nanosized MgFe₂O₄-based ferrite powder having heat generation ability in an AC magnetic field was prepared by bead milling and studied for thermal coagulation therapy applications. The crystal size and the particle size significantly decreased by bead milling. The heat generation ability in an AC magnetic field improved with the milling time, i.e. a decrease in crystal size. However, the heat generation ability decreased for excessively milled samples with crystal sizes of less than 5.5 nm. The highest heat ability (ΔT=34 °C) in the AC magnetic field (370 kHz, 1.77 kA/m) was obtained for fine MgFe₂O₄ powder having a ca. 6 nm crystal size (the samples were milled for 6-8 h using 0.1 mm ? beads). The heat generation of the samples was closely related to hysteresis loss, a B-H magnetic property. The reason for the high heat generation properties of the samples milled for 6-8 h using 0.1 mm ? beads was ascribed to the increase in hysteresis loss by the formation of a single domain. Moreover, the improvement in heating ability was obtained by calcination of the bead-milled sample at low temperature. In this case, the maximum heat generation (ΔT=41 °C) ability was obtained for a ca. 11 nm crystal size sample was prepared by crystal growth during the sample calcination. On the other hand, the ΔT value for Mg_0.5Ca_0.5Fe₂O₄ was synthesized using a reverse precipitation method decreased by bead milling.     

溶胶-凝胶法制备Sr2Bi4Ti5O18薄膜及其铁电性能研究

采用溶胶-凝胶法,在氧气氛中和层层晶化的工艺条件下,成功地制备了沉积在Pt/Ti/SiO₂/Si(100)衬底上的铁电性能优良的Sr₂Bi₄Ti₅O₁₈ (SBTi)薄膜,并研究了SBTi薄膜的微结构、表面形貌、铁电性能和疲劳特性.研究表明：薄膜具有单一的层状钙钛矿结构，且为随机取向；薄膜表面光滑，无裂纹，厚度约为725nm；铁电性能测试显示较饱和、方形的电滞回线，当外电场强度为275kV/cm时 关键词： 溶胶-凝胶法 铁电薄膜 2Bi₄Ti₅O₁₈')" href="#">Sr₂Bi₄Ti₅O₁₈     

Preparation and magnetic properties of BaFe12O19/Ni0.8Zn0.2Fe2O4 nanocomposite ferrite

Nanocomposite of hard (BaFe₁₂O₁₉)/soft ferrite (Ni_0.8Zn_0.2Fe₂O₄) have been prepared by the sol–gel process. The nanocomposite ferrite are formed when the calcining temperature is above 800 °C. It is found that the magnetic properties strongly depend on the presintering treatment and calcining temperature. The “bee waist” type hysteresis loops for samples disappear when the presintering temperature is 400 °C and the calcination temperature reaches 1100 °C owing to the exchange-coupling interaction. The remanence of BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite with the mass ratio of 5:1 is higher than a single phase ferrite. The specific saturation magnetization, remanence magnetization and coercivity are 63 emu/g, 36 emu/g and 2750 G, respectively. The exchange-coupling interaction in the BaFe₁₂O₁₉/Ni_0.8Zn_0.2Fe₂O₄ nanocomposite ferrite is discussed.     

Eddy-current-resistant SmCo5/CaF2 magnets produced via high-energy milling in polar and non-polar liquids

Processes of high-energy ball milling of SmCo₅ alloys were compared for three single-liquid environments without using additional surfactants. Both coarsely grained as-cast and nanocrystalline pre-milled SmCo₅ precursors showed tendency toward formation of thin flakes if milled in polar liquids (acetone and ethanol) in a marked contrast to milling in non-polar heptane. CaF₂ dielectric powder added prior to milling in the polar liquids tends to become attached on the flake surfaces. Milling in heptane in the presence of CaF₂ produces flake-like SmCo₅ particles which with increasing the milling time are found to incorporate an increasing amount of CaF₂. The SmCo₅—5 wt% CaF₂ mixtures milled for the optimum time in both the polar and non-polar liquids were successfully hot-pressed into laminated composite magnets having intrinsic coercivity of 25–30 kOe, maximum energy product of approximately 6.5 MG Oe and electrical resistivity of 500–600 μΩ cm, which is more than 7 times the resistivity of conventional Sm–Co magnets.