Polyol synthesis and magnetic study of Mn3O4 nanocrystals of tunable size

Nanosized manganese oxide particles were prepared by the so-called polyol process. The average diameter of the particles was controlled by the growth time. X-ray diffraction (XRD), transmission electron microscopy (TEM) and X-ray photon spectroscopy (XPS) show that the particles are well crystallized, pure, stoichiometric Mn₃O₄ single crystals of uniform size ranging from about 5 to 12 nm. The variation of their dc-magnetization, M, as a function of the magnetic field, H, and temperature, T, clearly corresponds to ferromagnetic ordering at low temperature, with a Curie temperature slightly higher than 40 K. The evidence for superparamagnetism in these particles, due to their very small size, has been discussed in the light of their M(H) and M(T) for zero-field-cooled (ZFC) and field-cooled (FC) plots.     

Synthesis and magnetic properties of NiFe2−xAlxO4 nanoparticles

Nanocrystalline Al-doped nickel ferrite powders have been synthesized by sol–gel auto-ignition method and the effect of non-magnetic aluminum content on the structural and magnetic properties has been studied. The X-ray diffraction (XRD) revealed that the powders obtained are single phase with inverse spinel structure. The calculated grain sizes from XRD data have been verified using transmission electron microscopy (TEM). TEM photographs show that the powders consist of nanometer-sized grains. It was observed that the characteristic grain size decreases from 29 to 6 nm as the non-magnetic Al content increases, which was attributed to the influence of non-magnetic Al concentration on the grain size. Magnetic hysteresis loops were measured at room temperature with a maximum applied magnetic field of ≈1 T. As aluminum content increases, the measured magnetic hysteresis curves become more and more narrow and the saturation magnetization and remanent magnetization both decreased. The reduction of magnetization compared to bulk is a consequence of spin non-collinearity. Further reduction of magnetization with increase of aluminum content is caused by non-magnetic Al³⁺ ions and weakened interaction between sublattices. This, as well as the decrease in hysteresis was understood in terms of the decrease in particle size.     

Controlled synthesis and magnetic properties of hard magnetic CoxC (x=2, 3) nanocrystals

We report our recent results in synthesis and characterization of cobalt carbide (Co₃C and Co₂C) nanoparticles and nanowires. The synthesis methods were based on a simple one-pot tetraethylene glycol reduction process. By changing the synthesis parameters, the nanocrystal morphology can be adjusted from nanoparticles with different size to nanowires. The magnetic properties of the nanostructure and their correlation to the crystalline structures and the nanoscale morphology have been investigated theoretically and experimentally. It is revealed that the properties are related to both the crystal structures and the morphology.     

Hydrothermal synthesis and magnetic properties of gadolinium-doped CoFe2O4 nanoparticles

CoFe_2−xGd_xO₄ (x=0-0.25) nanoparticles were synthesized via a simple hydrothermal process at 200 °C for 16 h without the assistance of surfactant. The as-synthesized powders were characterized by X-ray diffraction, transmission electron microscopy, and a vibrating sample magnetometer. The X-ray diffraction results showed that the as-synthesized powders were in the pure phase with a doping amount of ≤0.25, and the peaks could be readily indexed to the cubic spinel cobalt ferrite. Transmission electron microscopy and high resolution transmission electron microscopy observations revealed that the gadolinium-doped cobalt ferrite nanoparticles were single crystal, roughly spherical, uniformly distributed, and not highly agglomerated. The room temperature magnetic field versus magnetization measurements confirmed a strong influence of gadolinium doping on the saturation magnetization and coercivity due to large lattice distortion and grain growth of small particles.     

Fabrication and magnetic properties of amorphous Co0.71Pt0.29 nanowire arrays

Highly ordered Co_0.71Pt_0.29 alloy nanowire arrays have been fabricated successfully by direct current electro-deposition into the pores of a porous anodic aluminum oxide (AAO) template. SEM and TEM images reveal that the nanowires of array are uniform, well isolated, and parallel to one another. The aspect ratio of nanowires is over 200. XRD and EDS pattern indicates that amorphous Co_0.71Pt_0.29 structure was formed during electro-deposition. In amorphous sample, magnetocrystal anisotropy is very small, therefore, shape anisotropy plays a dominant role which leads to strong perpendicular anisotropy. High coercivity (Hc=1.7 kOe) and squareness (Mr/Ms) around 0.7 were obtained in the samples when the field was applied parallel to the axis of the nanowires. However, when it changed to polycrystalline structure after annealing, due to the competition of magnetocrystal anisotropy and shape anisotropy, the sample did not display perpendicular anisotropy.     

Effects of magnetic annealing on structure and multiferroic properties of pure and dysprosium substituted BiFeO3

In this work, the effects of magnetic annealing on crystal structure and multiferroic properties of BiFeO₃ and Bi_0.85Dy_0.15FeO₃ have been investigated. It is found that the X-ray diffraction patterns of pure BiFeO₃ samples are obviously broadened after magnetic annealing, whereas those of Bi_0.85Dy_0.15FeO₃ samples are almost unchanged. Magnetic field annealing did not affect the magnetic properties of these two kinds of samples much. However, ferroelectric properties of the two materials exhibited different behaviors after magnetic field annealing. For pure BiFeO₃ samples, the remnant polarizations (P_r) are suppressed; in contrast, for Bi_0.85Dy_0.15FeO₃ samples, P_r is greatly enhanced. Possible mechanisms for the effects of magnetic field annealing have been discussed.     

Effect of nanoparticle size on magnetic damping parameter in Co92Zr8 soft magnetic films

Co₉₂Zr₈(50 nm)/Ag(x) soft magnetic films have been prepared on Si (111) substrates by oblique sputtering at 45°. Nanoparticle size of Co₉₂Zr₈ soft magnetic films can be tuned by thickening Ag buffer layer from 9 nm to 96 nm. The static and dynamic magnetic properties show great dependence on Ag buffer layer thickness. The coercivity and effective damping parameter of Co₉₂Zr₈ films increase with thickening Ag buffer layer. The intrinsic and extrinsic parts of damping were extracted from the effective damping parameter. For x=96 nm film, the extrinsic damping parameter is 0.028, which is significantly larger than 0.004 for x=9 nm film. The origin of the enhancement of extrinsic damping can be explained by increased inhomogeneity of anisotropy. Therefore, it is an effective method to tailor magnetic damping parameter of thin magnetic films, which is desirable for high frequency application.     

Synthesis and magnetic properties of antiferromagnetic Li2MnO3 nanoribbons

Single-crystalline Li₂MnO₃ nanoribbons have been synthesized via the precursor template Na_0.44MnO₂ nanoribbons in LiNO₃-LiCl eutectic molten salt. The as-prepared Li₂MnO₃ nanoribbons are characterized by a range of methods including X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy dispersive X-ray spectroscopy, and selected-area electron diffraction techniques. Magnetization measurements show that the Li₂MnO₃ nanoribbons present weak ferromagnetism, spin-glass-like behavior, and exchange bias effect at low temperature. The magnetic behaviors of Li₂MnO₃ nanoribbons can be interpreted based on a core-shell model.     

Synthesis of nanocrystalline Co-Ni alloys by precursor approach and studies on their magnetic properties

Nanocrystalline Co-Ni alloys with different compositions were prepared by polyol reduction of mixed cobalt nickel hydroxides. The precursors (mixed cobalt nickel hydroxides) were prepared by co-precipitation. Powder X-ray diffraction analysis indicated the formation of fcc phase in the alloys and their crystallite size in the range 17-25 nm. Scanning electron microscopy and transmission electron microscopy studies revealed the morphology of the particles as being close to spherical, and the energy dispersive X-ray analysis showed the stoichiometry of the alloys. The magnetization as a function of field and temperature of the alloys, measured using a superconducting quantum interference device, showed superparamagnetic behavior with negligible coercivity and remanence values.     

The unusual magnetic and electronic properties of Gd0.5Ba0.5CoO2.9

Magnetic and electrical properties of well-characterized Gd_0.5Ba_0.5CoO_2.9 have been studied carefully in order to compare them with those of other analogous cobaltates of the type Ln_0.5A_0.5CoO₃ (Ln=La, Nd and A=Sr, Ba) which are ferromagnetic. The results show that Gd_0.5Ba_0.5CoO_2.9, which has A-site cation ordering at room temperature, does not become a genuine ferromagnet at low temperatures, but the ferromagnetic interactions observed at 280 K give over to an antiferromagnetic (AFM) state on cooling to 230 K. The AFM state is rendered ferromagnetic on the application of high magnetic fields. The properties can be understood on the basis of phase separation induced by the large A-site cation-disorder, arising from the size mismatch.     

Static and dynamic magnetic characteristics of BaCo0.5Mn0.5Ti1.0Fe10O19

The effect of Mn²⁺Co²⁺Ti⁴⁺ substitution on microwave absorption has been studied for BaCo_0.5Mn_0.5Ti_1.0Fe₁₀O₁₉ ferrite-acrylic resin composites in frequency range from 12 to 20 GHz. X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer, AC susceptometer and vector network analyzer were used to analyze the structural, magnetic and microwave absorption properties. The results showed that the magnetoplumbite structures for all samples have been formed. Based on microwave measurement on reflectivity, BaCo_0.5Mn_0.5Ti_1.0Fe₁₀O₁₉ may be a good candidate for electromagnetic compatibility and other practical applications at high frequency.     

Synthesis and rheological investigation of a magnetic fluid using olivary silica-coated iron particles as a precursor

A new type of magnetic fluid was prepared by dispersing monodispersed iron–silica (Fe–SiO₂) composite particles in polyethylene glycol (PEG) 400. The composite particles Fe–SiO₂ were synthesized by hydrogen reduction from α-Fe₂O₃–SiO₂ spheres. Their microstructures were observed by a high-resolution transmission electron microscope (HRTEM) and the magnetism was characterized with a superconducting quantum interference device (SQUID) magnetometer. Both steady-state and dynamic rheological properties of the magnetic fluid under different magnetic fields were studied by using a rheometer. Experimental results show that this magnetic fluid has a relatively high magnetoviscous effect at low shear rates. The yield stress of this material shows an increasing trend with a magnetic flux density. Also, viscoealstic properties of such materials are different from conventional ones.     

Structural transformations and magnetic properties of Fe60Pt15B25 and Fe60Pt25B15 nanocomposite alloys

Structural and magnetic properties of two rapidly solidified and post-annealed Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅ alloys are compared. The as-quenched Fe₆₀Pt₁₅B₂₅ ribbon was fully amorphous whereas in the Fe₆₀Pt₂₅B₁₅ alloy the amorphous phase coexists with an fcc FePt disordered solid solution. Differential scanning calorimetry curves of both alloys reveal a single exothermal peak with onset temperatures of 873 and 847 K for Fe₆₀Pt₁₅B₂₅ and Fe₆₀Pt₂₅B₁₅, respectively. Magnetically hard, tetragonal ordered L1₀ FePt and magnetically soft Fe₂B nanocrystalline phases were formed due to the annealing of the alloys, as indicated by X-ray diffraction and Mössbauer spectroscopy measurements. Two-phase behavior was detected in the temperature dependence of magnetization of the annealed samples. A magnetic hardening was observed for all annealed ribbons. Magnetic properties of the annealed alloys, studied by hysteresis loop measurements, were related to the differences in the relative fractions of the hard and soft magnetic phases calculated from Mössbauer spectra. The alloy with 25 at% Pt exhibits better hard magnetic properties (H_c=437 kA/m, M_r/M_s=0.74) than the alloy with smaller Pt content (H_c=270 kA/m, M_r/M_s=0.73) mainly due to the larger abundance of the ordered tetragonal FePt phase.     

Synthesis and magnetic characterization of Zn0.6Ni0.4Fe2O4 nanoparticles via a polyethylene glycol-assisted hydrothermal route

Zn-doped nickel ferrite nanoparticles (Zn_0.6Ni_0.4Fe₂O₄) have been prepared via a surfactant, polyethylene glycol assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy, transmission electron microscopy (TEM), and vibrating scanning magnetometry (VSM) were used for the structural, morphological, and magnetic characterizations of the product, respectively. TEM analysis revealed that the nanoparticles have a narrow size distribution, with average particle size of 15±1 nm, which agrees well with the XRD based estimate of 14±2 nm. The absence of saturation and remanent magnetization, and coercivity in the high temperature region of the M-H curve and non-zero magnetic moments indicate superparamagnetism of the nanoparticles with a canted spin structure. The appearance of a peak on the temperature-dependent zero-field cooling magnetization curve at ∼190 K indicates the blocking temperature of the sample.     

New ferromagnetic La3Co2TaO9 double perovskite: Structural and magnetic properties

The new double perovskite La₃Co₂TaO₉ has been prepared by a solid-state procedure. The crystal and magnetic structures have been studied from X-ray powder diffraction (XRPD) and neutron powder diffraction (NPD) data. Rietveld refinements were performed in the monoclinic space group P2₁/n. The structure consists of an ordered array of alternating B′O₆ and B″O₆ octahedra sharing corners, tilted along the three pseudocubic axes according to the Glazer notation a⁻b⁻c⁺. Rietveld refinements show that at RT the cell parameters are a=5.6005(7) Å, b=5.6931(7) Å, c=7.9429(9) Å and β=89.9539(7)°, and the refined crystallographic formula of this “double perovskite” can be written as La₂(Co)_2d(Co_1/3Ta_2/3)_2cO₆. Magnetization measurements and low-temperature NPD data show that the perovskite is a ferromagnet with T_C=72 K. At high T it follows the Curie–Weiss law with an effective magnetic moment of 3.82μ_B per Co ion which is very close to spin only Co²⁺ (HS).     

Effects of annealing temperature on structure and magnetic properties of CoAl0.2Fe1.8O4/SiO2 nanocomposites

CoAl_0.2Fe_1.8O₄/SiO₂ nanocomposites were prepared by sol–gel method. The effects of annealing temperature on the structure and magnetic properties of the samples were studied by X-ray diffraction, transmission electron microscopy, vibrating sample magnetometer and Mössbauer spectroscopy. The results show that the CoAl_0.2Fe_1.8O₄ in the samples exhibits a spinel structure after being annealed. As annealing temperature increases from 800 to 1200 °C, the average grain size of CoAl_0.2Fe_1.8O₄ in the nanocomposites increases from 5 to 41 nm while the lattice constant decreases from 0.8397 to 0.8391 nm, the saturation magnetization increases from 21.96 to 41.53 emu/g. Coercivity reaches a maximum of 1082 Oe for the sample annealed at 1100 °C, and thereafter decreases with further increasing annealing temperature. Mössbauer spectra show that the isomer shift decreases, hyperfine field increases and the samples transfer from mixed state of superparamagnetic and magnetic order to the completely magnetic order with annealing temperature increasing from 800 to 1200 °C.     

Dielectric and magnetic properties of low-temperature fired NiCuZn-BaTiO3 composites

The composition effects on the dielectric and magnetic properties of NiCuZn-BaTiO₃ composites fired at low temperature were investigated. The coexistence of perovskite BaTiO₃ and spinel ferrite phases in the composites were observed; no significant chemical reactions occurred between BaTiO₃ and NiCuZn ceramics during sintering. The nanosized BaTiO₃ powders favored a decrease in grain size. The saturation magnetization, remanent magnetization and real permeability continuously decreased with increasing BaTiO₃ content. And the real permittivity continuously increased with the BaTiO₃ content. The Q-factor (quality factor) exhibited relatively high values with 20-30 wt% BaTiO₃. All composite materials exhibited a low dielectric loss below 100 MHz. Synthetically considerations, the composites with 20-30 wt% BaTiO₃ could obtain relatively high real permeability and real permittivity values, and the magnetic and dielectric losses were relatively low, so they were the best candidates to produce LC-integrated chip elements.     

Structural and magnetic characteristics of Co1−xNix/2Srx/2Fe2O4 nanoparticles

Co_1−xNi_x/2Sr_x/2Fe₂O₄ (x=0–0.5 in steps of 0.1) ferrite nanoparticles have been synthesized at room temperature, without calcination, using a reverse micelle process. The site preference was determined by Mössbauer spectroscopy at 300 K. The hyperfine parameters were obtained, for the whole series of solid solutions. For the X≤0.20 samples, the spectra were fitted with two discrete sextets and for the X>0.20 samples, a magnetic hyperfine field distribution and a doublet were also imposed in the fit procedure. Hysteresis loops were measured using a superconducting quantum interference device magnetometer at 2 K and 300 K. The results indicate that the relative decrease in saturation magnetization of nanoparticles compared to the submicron particles could be attributed to a surface spin termination and disorder. Magnetic dynamics of the nanoparticles was studied by the measurement of ac magnetic susceptibility versus temperature at different frequencies and it is found that the results are well described by the Vogel–Fulcher model.     

Synthesis and magnetic properties of antiferromagnetic Co3O4 nanoparticles

Antiferromagnetic Co₃O₄ nanoparticles with diameter around 30 nm have been synthesized by a solution-based method. The phase identification by the wide-angle X-ray powder diffraction indicates that the Co₃O₄ nanoparticle has a cubic spinel structure with a lattice constant of 0.80843(2) nm. The image of field emission scanning electron microscope shows that the nanoparticles are assembled together to form nanorods. The magnetic properties of Co₃O₄ fine particles have been measured by a superconducting quantum interference device magnetometer. A deviation of the Néel temperature from the bulk is observed, which can be well described by the theory of finite-size scaling. An enhanced coercivity as well as a loop shift are observed in the field-cooled hysteresis loop. The exchange bias field decreases with increasing temperature and diminishes at the Néel temperature. The training effect and the opening of the loop reveal the existence of the spin-glass-like surface spins.     

Effect of Mo doping on magnetic and transport properties of La0.5Sr0.5CoO3

The substitutional effect of Mo on the magnetic and transport properties of double exchange ferromagnets, La_0.5Sr_0.5Co_1−x Mo_xO₃ (0?x?0.2) has been investigated. Substitution of 10% Mo at the Co-site of La_0.5Sr_0.5CoO₃ decreases the Curie temperature by ∼60 K than that of the parent compound and the long-range ferromagnetic ordering disappears for x?0.2. The Mo-doped samples, however, undergo a transition from the parent metallic state to the insulating state below T_c. The insulating state is found to obey Mott's variable range hopping of conduction. The effect of Mo substitution is attributed to the factors namely, (i) the dilution of magnetic Co sublattice, (ii) the reduction of Co⁴⁺/Co³⁺ ratio resulting in a reduced carrier concentration and (iii) disruption of the intermediate spin structure of Co, namely Co³⁺: t_2g⁵e_g¹.