Solid-phase microextraction method for gas chromatography with mass spectrometric and pulsed flame photometric detection: studies of organoarsenical speciation

The development, optimization, and application of a novel method for arsenic speciation based on capillary gas-liquid chromatography with simultaneous quadrupole ion-trap mass spectrometric (MS) detection and pulsed flame photometric detection (PFPD) is described. The method couples the sensitive arsenic-selectivity of PFPD with the structure elucidation capability of molecular MS detection for the determination of trace levels of unknown organoarsenicals in complex matrices. The conditions that affect the PFPD response in the presence of interfering species were optimized using the sequential Simplex algorithm for three key factors: gate delay (18.3 ms), gate width (9.1 ms), and combustion gas composition (16.6 ml/min H2). Complete discrimination in the PFPD of the arsenic signal from interfering S-, C-, and OH-emitting species that are problematic in existing methods was achieved. Additionally, a revised interpretation of our previously reported mechanism [J. Chromatogr. A 807 (1998) 253] for the dithiol derivatization and subsequent GC-MS determination of dimethylarsinic acid is presented.     

Analysis of procyanidins in chocolate by reversed-phase high-performance liquid chromatography with electrospray ionisation mass spectrometric and tandem mass spectrometric detection

Four cation-exchange materials, possessing propanesulfonic acid ligands, for use in capillary electrochromatography were prepared from different commercially available 5-microm bare-silica particles ranging from 80 to 800 A in pore size. The performance of the materials was investigated at different compositions of the mobile phase (pH, ionic strength, and acetonitrile content) using tricyclic antidepressants and related quaternary ammonium analogues as test analytes. The wide-pore materials promoted pore flow, but this had no positive influence on the performance. The small-pore (highest surface area) particles gave, as could be expected, the best selectivity.     

Comparison of in-tube sorptive extraction techniques for non-polar volatile organic compounds by gas chromatography with mass spectrometric detection

A commercial in-tube sorptive extraction device, known as solid-phase dynamic extraction (SPDE), has been evaluated for the extraction of non-polar volatile aromatic analytes from aqueous solutions in both headspace and liquid injection modes. An automated sampler is used with a gas-tight 2.5 ml syringe equipped with a special needle that is coated on the inside with a non-polar extraction phase. After absorption onto the phase, the analytes were thermally desorbed directly into a GC-MS system. The technique was evaluated for the determination of furan, benzene and toluene. The sensitivity for toluene was greatly improved on using SPDE compared to static headspace. A slight increase in sensitivity was observed for benzene but none for determination of furan. Estimated limits of detection ranged from 0.2 to 2 microg/l.     

The analysis of beta-agonists by packed-column supercritical fluid chromatography with ultra-violet and atmospheric pressure chemical ionisation mass spectrometric detection

Packed-column supercritical fluid chromatography (pSFC) using ultra-violet (UV) and atmospheric pressure chemical ionisation (APCI) mass spectrometry (MS) provides a versatile method for the identification and quantification of beta-agonists. We have achieved good separation of clenbuterol, salbutamol, terbutaline and fenoterol with good resolution and reasonable retention times using a high concentration of methanol modifier in the supercritical CO2, together with small amounts of both acidic (trifluoroacetic acid, TFAA) and basic (triethylamine, TEA, or diethylamine, DEA) additives. APCI-MS gave unambiguous identification of the 4 analytes, and increasing cone voltage provided informative fragmentation patterns. The pSFC-MS technique was shown to be linear (R2 > or = 0.996) over the concentration range 1-50 micrograms ml-1. Single ion monitoring (SIM) gave detection limits (on-column) of 2.5 ng (clenbuterol), 0.83 ng (terbutaline), 7.6 ng (salbutamol) and 2.7 ng (fenoterol). The pSFC-MS system was shown to be reproducible within a day, between days, and between restrictors. Analysis of milk samples 'spiked' with beta-agonists showed that the matrix caused no interference, with detection limits of approximately 500 micrograms l-1 of beta-agonists. More dilute solutions could be analysed by pre-concentration before the SFC stage.     

Speciation analysis for mercury in gas condensates by capillary gas chromatography with inductively coupled plasma mass spectrometric detection

A method allowing species-selective determination of atomic mercury, non-polar dialkylated mercury compounds,polar monoalkylated species and inorganic mercury complexes in natural gas condensates was developed. Inductively coupled plasma mass spectrometry was employed as a detection method for capillary gas chromatography and compared with microwave induced plasma atomic emission detection for the analysis of hydrocarbon-rich matrices. The method was based on two consecutive injections allowing comprehensive speciation analysis. First a sample aliquot was diluted with toluene and analysed for Hg0 and individual dialkylmercury compounds. Then, another aliquot was butylated with a Grignard reagent for the species specific determination of Hg(II) and monoalkylated mercury species. The detection limits were down to 0.08 pg level.     

Capillary supercritical fluid chromatography with simultaneous flame ionization and mass spectrometric detection

A simple interface between a capillary supercritical fluid chromatograph and an Extranuclear Simulscan mass spectrometer is described. The SFC column is directly inserted into the ion source through the existing GC-interface. The system is equipped with a splitting device which allows simultaneous EI/MS and flame ionization detection when CO₂ is used as the supercritical phase. The effect of source temperature and pressure on CO₂ clustering was studied for optimization of source conditions. The performance of the system was evaluated with a series of model compounds and standard mixtures.     

Pesticide trace analysis using solid-phase extraction and gas chromatography with electron-capture and tandem mass spectrometric detection in water samples

Gas chromatography (GC) with electron-capture detection (ECD), mass spectrometry (MS) and tandem mass spectrometry (MS-MS) were employed for the identification of 12 pesticides in water samples. For this purpose, a solid-phase extraction procedure with C18 cartridges was used, optimising the breakthrough volume and the saturation concentration. In GC-MS-MS, the lowest detectable concentrations for the pesticides were between 2 and 26 ng l(-1), recoveries ranged from 70 to 133% in water samples spiked at 100 ng l(-1) and the relative standard deviations were in the range 5.3 to 17.4%. The proposed analytical methodology was applied to analyse pesticides in wetland samples from Almería (Spain).     

Rapid and sensitive method for determining free amino acids in honey by gas chromatography with flame ionization or mass spectrometric detection

This paper describes a rapid, sensitive and specific method for determination of free amino acids in honey involving a new reaction of derivatization and gas chromatography (GC) with flame ionization (FID) and mass spectrometric (MS) detection. The method allows the determination of 22 free amino acids in honey samples in a short time: 8 and 5 min for GC-FID and GC-MS, respectively. Quantitation was performed using Norvaline as internal standard, with detection limits ranging between 0.112 and 1.795 mg/L by GC-FID and between 0.001 and 0.291 mg/L by GC-MS in the selected-ion monitoring mode. The method was validated and applied to a set of 74 honey samples belonging to four different botanical origins: eucaliptus, rosemary, orange and heather. The statistical treatment of data shows a correct classification of different origins over 90%.     

Evaluation of time-of-flight mass spectrometric detection for fast gas chromatography

Separations below 1 s of a mixture of organic compounds ranging from C5 to C8 have been performed to investigate the performance of a time-of-flight mass spectrometer in fast gas chromatography. The gaseous samples were focussed on a cold trap, and then injected after thermal desorption to obtain the required narrow input band-widths. Also, to obtain a very fast separation, a short narrow bore column was used, operated at above-optimum inlet pressures. With this system, it was possible to identify ten compounds within 500 ms, showing peak-widths (2.354sigma) as narrow as 12 ms. The spectral acquisition rate used for these analyses was 500 Hz. The quality of the recorded spectra and the comparison with library spectra was very high. Deconvolution algorithms offer the possibility of identifying overlapping peaks. It is shown that the spectral scan speed of the time-of-flight mass spectrometer is high enough for very fast separations.     

Simultaneous determination of anthraquinones in radix Polygoni multiflori by capillary gas chromatography coupled with flame ionization and mass spectrometric detection

A rapid, accurate and reliable analytical method was developed for the simultaneous determination of five major anthraquinones, aloe-emodin, chrysophanol, emodin, physcion, and rhein, in radix Polygoni multiflori, a traditional Chinese herbal medicine. The method comprises a fast ultrasonic extraction with methanol and derivatization with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA)+1% trimethylchlorosilane (TMCS) followed by capillary gas chromatographic (GC) separation. The effect of reaction time on the derivatization of anthraquinones was examined. A baseline separation of the anthraquinone and internal standard derivatives was achieved in 15min. The detection limits range from 0.22 to 0.60microg/mL for the five anthraquinones. The calibration curves are linear over the concentration range studied (from the detection limits to 40.0microg/mL) with the squares of correlation coefficients, R2, greater than 0.998. The developed method was successfully applied to the simultaneous determination of anthraquinones in radix P. multiflori samples. The peak identification was confirmed using GC-MS. The contents of anthraquinones in radix P. multiflori samples studied were 27.41, 289.6, 64.22, 202.1, 288.6microg/g for chrysophanol, emodin, aloe-emodin, physcion, rhein, respectively. All relative standard deviations are less than 3.2%. The recoveries range from 80.2% to 119.3% for the five analytes. To the authors' best knowledge, this is the first GC method reported for the simultaneous determination of the five anthraquinones in radix P. multiflori.     

Determination of minor and trace volatile compounds in wine by solid-phase extraction and gas chromatography with mass spectrometric detection

A new method for the quantitative determination of important wine odorants has been developed. The wine (50 ml) is extracted in a 200 mg solid-phase extraction (SPE) cartridge filled with Lichrolut-EN resins from Merck. The elution is carried out with 1.3 ml of dichloromethane. These extracts are directly analyzed by GC-Ion Trap-MS without further concentration. Twenty-seven important wine odorants, such as volatile phenols, vanillin derivatives, aliphatic lactones, nor-isoprenoids, minor esters and terpenols, can be quantitatively determined in a single gas chromatography-mass spectrometry (GC-MS) run. The recoveries in the SPE isolation are in good agreement with those expected from the calculation of breakthrough volumes from solid-liquid distribution coefficients and are higher than 90%, except for guaiacol, vanillin, 2,6-dimethoxyphenol and 4-vinylphenol. In most cases, precision is below 10%. Method linearity is satisfactory, with r2 higher than 0.99 in all cases. The analysis of spiked samples has shown that there is good agreement between the real mass of compound added to the wine and that determined by analysis. In all cases detection limits are below the odor detection threshold of the compounds, and the calibrated interval covers the natural range of occurrence of the compounds in wine.     

Supercritical fluid extraction and quantitative determination of organophosphorus pesticide residues in wheat and maize using gas chromatography with flame photometric and mass spectrometric detection

An automated method using supercritical CO2 and clean-up by solid-phase extraction (SPE) using graphitized carbon black, has been developed for the quantitative determination of organophosphorus pesticide (OPP) residues in wheat and maize. Recoveries were as good as, or better than, those obtained using liquid extraction (LE) and gel permeation chromatography (GPC) for 10 OPP's spiked at levels equivalent to 0.05 and 0.50 microg/g. Lower limits of detection were possible using supercritical fluid extraction (SFE). Incurred residues were found in wheat and maize samples, and good agreement was obtained using SFE+SPE and LE+GPC. The SFE+SPE method required less analyst time and organic solvent, and hazardous waste was reduced.     

Improved analysis of volatile halogenated hydrocarbons in water by purge-and-trap with gas chromatography and mass spectrometric detection

An analytical system composed of a purge-and-trap injection system coupled to gas chromatography with mass spectrometric detection (PTI-GC-MS) specific for the analysis of volatile chlorinated hydrocarbons (VCHCs) (chloroform; 1,1,1-trichloroethane; tetrachloromethane; 1,1,2-trichloroethylene; tetrachloroethylene) and trihalomethanes (THMs) (chloroform; bromodichloromethane; dibromochloromethane; bromoform) in water was optimised. Samples were purged and trapped in a cold trap (-100 degrees C) fed with liquid nitrogen (cryo-concentration). In order to make this method suitable also for only slightly contaminated waters, some modifications were made to PTI sample introduction, in order to avoid any air intake into the system. PTI, GC and MS conditions were optimised for halogenated compound analysis and limits of detection (LOD) were evaluated. The proposed method allows analysis of samples whose concentrations range from microg/L to ng/L. It is, therefore, applicable to drinking waters, in analyses required by law, and to slightly contaminated aqueous matrices, such as those found in remote areas, in environmental monitoring. Moreover, by changing cold trap temperature, even sparkling mineral waters can be analysed, thus avoiding CO2 interference during the cryo-concentration phase. Our method has been successfully used on real samples: tap water, mineral water and Antarctic snow.     

Qualitative and quantitative analysis of pyrolysis oil by gas chromatography with flame ionization detection and comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry

Pyrolysis oils have attracted a lot of interest, as they are liquid energy carriers and general sources of chemicals. In this work, gas chromatography with flame ionization detector (GC-FID) and two-dimensional gas chromatography with time-of-flight mass spectrometry (GC×GC-TOFMS) techniques were used to provide both qualitative and quantitative results of the analysis of three different pyrolysis oils. The chromatographic methods and parameters were optimized and solvent choice and separation restrictions are discussed. Pyrolysis oil samples were diluted in suitable organic solvent and were analyzed by GC×GC-TOFMS. An average of 300 compounds were detected and identified in all three samples using the ChromaToF (Leco) software. The deconvoluted spectra were compared with the NIST software library for correct matching. Group type classification was performed by use of the ChromaToF software. The quantification of 11 selected compounds was performed by means of a multiple-point external calibration curve. Afterwards, the pyrolysis oils were extracted with water, and the aqueous phase was analyzed both by GC-FID and, after proper change of solvent, by GC×GC-TOFMS. As previously, the selected compounds were quantified by both techniques, by means of multiple point external calibration curves. The parameters of the calibration curves were calculated by weighted linear regression analysis. The limit of detection, limit of quantitation and linearity range for each standard compound with each method are presented. The potency of GC×GC-TOFMS for an efficient mapping of the pyrolysis oil is undisputable, and the possibility of using it for quantification as well has been demonstrated. On the other hand, the GC-FID analysis provides reliable results that allow for a rapid screening of the pyrolysis oil. To the best of our knowledge, very few papers have been reported with quantification attempts on pyrolysis oil samples using GC×GC-TOFMS most of which make use of the internal standard method. This work provides the ground for further analysis of pyrolysis oils of diverse sources for a rational design of both their production and utilization process.     

Determination of lewisite oxide in soil using solid-phase microextraction followed by gas chromatography with flame photometric or mass spectrometric detection

A rapid, sensitive, and convenient method is described for determining Lewisite oxide in soil. Samples are initially fortified with phenylarsine oxide (surrogate), then both species are extracted using ascorbic acid solutions containing 1,3-propanedithiol (derivatizing reagent). The corresponding filtered supernatant is sampled using a solid-phase microextraction fiber. Collected analytes are thermally desorbed in a heated gas chromatographic inlet, separated using fused-silica capillary columns ("primary" and "confirmatory"), and detected with either a mass spectrometric (selected ion monitoring mode) or flame photometric (sulfur-selective mode) detector. Two independent statistically-unbiased procedures were used to evaluate the detection limit for Lewisite oxide; the values range between 0.1 and 0.5 microg g(-1) soil.     

Determination of sulfonamides by packed column supercritical fluid chromatography with atmospheric pressure chemical ionisation mass spectrometric detection

Sulfonamide antibiotics are widely used to prevent bacterial infections in livestock, and residues are commonly found in milk and meat. Packed column supercritical fluid chromatography (pSFC) with detection using ultra violet (UV) and atmospheric pressure chemical ionisation (APCI) mass spectrometry (MS) provides a versatile method for the detection and quantification of six major sulfonamides. The APCI mass spectra for all the sulfonamides consisted of protonated molecules at low cone voltages. Increasing the cone voltage led to informative fragmentation patterns, which provided structural information for identification purposes. The pSFC-APCI-MS technique was shown to be linear (r2 > or = 0.999) over the concentration range 0.1-50 micrograms ml-1 using total ion current. The precision and the accuracy of the system and validation of sample preparation are acceptable, with RSD < 2% and relative error 8%. Selected ion monitoring gave detection limits as follows: sulfadiazine 41, sulfamethoxazole 45, sulfamerazine 47, sulfamethizole 59, sulfamethazine 181 and sulfadimethoxine 96 micrograms l-1, which are lower than the amounts permitted in milk products. The APCI pSFC-MS system was shown to have a high degree of reproducibility. The technique was then applied to determine the above sulfonamides in milk. The results obtained show that there are no matrix effects from the milk and that the detection limits remained as stated for the standard solutions.     

Liquid chromatography with electrospray ionisation mass spectrometric detection of phenolic compounds from Olea europaea.

The results demonstrate the potential of electrospray ionisation mass spectrometry for the specific detection of phenolic species in olives. Phenolic compounds were detected with greater sensitivity in the negative ion mode, but results from positive and negative ion modes were complementary with the positive ion mode showing structurally significant fragments. This is demonstrated by the identification of oleuropein and isomers of verbascoside. The structure of the latter were confirmed by retention, mass spectral and nuclear magnetic resonance data. These isomers have not previously been reported in olive.     

Linearity of a flame ionisation detector for capillary gas chromatography

Summary The influence of the nitrogen and hydrogen flow rates on the linearity of the flame ionisation detector is investigated and flow-rates which give a linear response over five orders of magnitude are determined.