Thermal and mechanical properties of irradiated poly(vinyl chloride)/calcium carbonate composite

A composite consisting of PVC and CaCO₃ particles was irradiated with different doses of Gamma rays or electron beam in order to compensate the tensile strength decreases by filler addition. The deployment of irradiation process on the composite improved significantly the tensile strength by about 10–20 % using E-beam and Gamma irradiation at a dose of 250 kGy, respectively. Moreover, the irradiated composite exhibited higher thermal stability. Two thermal dehydrochlorination processes after irradiation have been observed instead of three thermal process before. The calculation of the activation energy of each step showed that initiation step consumed about 60 % of the used energy.     

Thermal degradation of poly(vinyl chloride)

This paper presents an initial attempt at describing poly(vinyl chloride) (PVC) thermal degradation through a semi-detailed and lumped kinetic model. A mechanism of 40 species and pseudocomponents (molecules and radicals) involved in about 250 reactions permits quite a good reproduction of the main characteristics of PVC degradation and volatilization. The presence of the two step mechanism—the first step of which corresponds to dehydrochlorination and the second to the tar release and residue char formation—are correctly predicted both in quantitative terms and in the temperature ranges. The model was validated by comparison with several thermo gravimetric analyses, both dynamic at different heating rates, and isothermal. When compared with the typical one step global apparent degradation models, the approach proposed here spans quite large operative ranges, especially when it comes to predicting product distributions. The initial results of these product predictions, even though quite preliminary, are encouraging and confirm the validity of the model.     

Thermal degradation of ethanolamine treated poly(vinyl chloride)/wood flour composites

The influence of ethanolamine treatment of wood flour on the thermal degradation behaviour of PVC/wood flour composites was investigated. The decomposition of untreated and treated wood flour and PVC/wood flour composites was measured using thermogravimetric analysis (TGA). The TGA indicated an accelerated degradation of the composite after treatment in a temperature range between 240 and 350 °C. This was caused by a synergistic decomposition of treated wood flour and polymer. Additionally, the colour of the material was measured in order to analyse the effect of the treatment. The lightness of the composite was reduced with increasing ethanolamine concentration.     

Thermal properties of poly(vinyl chloride)/polyurethane blends

Blends of poly(vinyl chloride) and a polyurethane elastomer were investigated by DSC and tensile testing. Up to 30 wt% single glass transition was found. It was concluded that the polyurethane forms partly a true blend and is partly disperged in the continuous blend phase.     

Thermal decomposition of poly(vinyl chloride) and chlorinated poly(vinyl chloride). II. Organic analysis

A concerted study of poly(vinyl chloride), chlorinated poly(vinyl chloride), and poly(vinylidene chloride) polymers by spectroscopy, thermal analysis, and pyrolysis-gas chromatography resulted in a proposed mechanism for their thermal degradation. Polymer structure with respect to total chlorine content and position was determined, and the influence of these polymer units on certain of the decomposition parameters is presented. Distinguishing differences were obtained for the kinetics of decomposition, reactive macroradical intermediates, and pyrolysis product distributions for these systems. It was determined that chlorinated poly(vinyl chloride) systems with long-chain ? CHCI? units were more thermally stable than the unchlorinated precursor, exhibited increasing activation energy for the dehydrochlorination, and produced chlorine-containing macroradical intermediates and chlorinated aromatic pyrolysis products. The poly(vinyl chloride) polymer was relatively less thermally stable, exhibited decreasing activation energy during dehydrochlorination, and produced polyenyl macro-radical intermediates and aromatic pyrolysis products.     

Thermal degradation of γ-irradiated poly(vinyl chloride)

The thermal degradation of unstabilized poly(vinyl chloride) irradiated with γ-rays has been investigated by dynamic thermogravimetry in a nitrogen atmosphere. The overall effect of irradiation is to render PVC more susceptible to thermal degradation. The change in activation energy of degradation with dose showed a behavior parallel with the change of intrinsic viscosity with dose. The minimum and maximum E_a values were found to correspond with the minimum and maximum observed on [η] versus dose curves. This behavior indicates an inverse relationship between the rate of thermal degradation and molecular size.     

Thermal decomposition of poly(vinyl chloride) and chlorinated poly(vinyl chloride). I. ESR and TGA studies

Significant effort has been made in the past by many workers to investigate the mechanism of thermal decomposition of poly(vinyl chloride) (PVC). The presence and role of free radicals has been controversial in this regard. Our data on PVC and chlorinated PVC systems demonstrate the existence of macroradicals in the early stage of thermal decomposition under inert and oxidative atmospheres. Data from conventional thermogravimetric experiments are used in conjunction with the electron spin resonance findings.     

Thermal degradation of poly(vinyl chloride): effect of oxygen on the thermal degradation of poly(vinyl chloride)

On the basis of the simultaneously measured free radical generation and HCl evolution a mechanism accounting for the effect of the oxygen on the degradation of poly(vinyl chloride) (PVC) is proposed. The mechanism is based on the reaction of oxygen with radicals generated in PVC to form unstable peroxy radicals. In addition, it is proposed that oxygen reacts directly with conjugated polyenes to form peroxy linkage.     

Poly(vinyl chloride) composite emulsion resins modified by polyurethane

An ionomer-type of polyurethane (PU) emulsion was prepared from toluene diisocyanate (TDI), polypropylene glycol (PPG) and dimethylol propionic acid (DMPA) following a self-emulsification process. The modified poly(vinyl chloride) (PVC) emulsion resin was obtained by in situ emulsion copolymerization using the PU as seeds in an autoclave. The effects of PU molecular weight on the mechanical properties and thermal stability of the PU/PVC materials were investigated. The composite latex particles and composite materials were determined and characterized using a laser particle size analyzer, transmission electron microscopy or scanning electron microscopy. The study results showed that the PU/PVC hybrid emulsion particles possess a core/shell structure. When the general mechanical properties of the composite materials increase, the thermal stabilities decrease a little. The tough fractures on the surface of the PU/PVC composite sample following impact are quite obvious. __________ Translated from Journal of Hebei Normal University (Natural Science Edition), 2007, 31(2): 228–232 [译自: 河北师范大学学报(自然科学版)]     

Thermal properties of rhodium(III) chloride

Thermal decomposition of rhodium(III) chloride under inert, oxidative and reductive gas atmospheres was investigated in order to determine its thermal properties. Stoichiometries of the reactions occurring during heating are described. it is suggested that the chemical formula of soluble rhodium(III) chloride should be presented as RhCl₃·HCL·xH₂O. Cold crystallisation of anhydrous rhodium(III) chloride at a temperature of about 500°C was established. The procedure for quantitative determination of volatile matter (water and hydrochloric acid) content and rhodium content by thermogravimetry is given and discussed. The repeatability and reproducibility of the method are estimated. This revised version was published online in July 2006 with corrections to the Cover Date.     

Some optical and mechanical properties of poly(vinyl chloride)

The optical and mechanical properties of poly(vinyl chloride) film were examined by observing both the stress and birefringence during stretching at constant rate, during relaxation at constant length and during a dynamic birefringence experiment. Experiments were also done by varying the temperature at constant length. The changes in birefringence are interpreted in terms of changes in negative distortional birefringence, changes in positive orientation birefringence, and possible reversible changes in birefringence with temperature arising from conformational changes in the polymer chain and changes in the contribution of birefringent crystals.     

Dynamic mechanical properties of plasticized poly(vinyl chloride)

The complex compliance in extension of gels of poly(vinyl chloride) (PVC) in di(2-ethylhexyl) phthalate (DOP) and in tricresyl phosphate (TCP) was measured over the frequency range from 0.6 to 0.006 cps and the temperature range from ?66 to 65°C: the weight fractions of DOP and TCP in the gels were 0.32, 0.40, 0.49, and 0.59. Measurements were carried out in an apparatus using forced low-frequency longitudinal osillations. Data for the gels could not be combined by the method of reduced variables, since there were gradual changes with decreasing temperature, attributable to an increase in crystallinity. Application of the reduction method of Ninomiya and Ferry for solutions of crystalline polymers was found to be successful. The apparent melting temperatures (T′_m) were obtained from the temperature dependence of the vertical shift factors. An apparent heat of fusion of ca. 120 cal/mole of monomer unit was found. This melting range was in agreement with that of secondary crystallinity in plasticized PVC reported in calorimetric studies by Juijn. With decreasing temperature, two phenomena occurred in the temperature range from T_g + ca. 80°C to T_g: the vitrification of a concentrated amorphous solution and the slight crystallization of the polymeric component. The larger the difference between T_g and T′_m the broader the primary dispersion zone on the frequency scale. This broadening effect was explained as due to the difference in dependence of T_g and T′_m on plasticizer concentration, without any need to consider any specific interaction between plasticizer and PVC.     

Electrical properties and X-ray diffraction of wood and wood plastic composite (WPC)

Wood plastic composite (WPC) of kadom, simul, mango and debdaro were prepared with two monomers, methylmethacrylate (MMA) and butylmethacrylate (BMA) using high energy ionizing radiation. X-ray diffraction and scanning electron microscope (SEM) studies reveal that significant grafting occurred with wood fiber. Electric properties like resistivity and dielectric constant of both wood and WPC were measured under different moisture contents and relative humidities. The resistivities of wood decreased dramatically with increase of moisture content, but those of WPC decreased very slowly with moisture content. The dielectric constant of wood increased significantly with moisture content but no significant difference was observed in the case of WPC within the range of moisture contents studied. The dielectric constants of untreated wood also increased with their densities.     

Novel preparation of electrically conducting poly (vinyl chloride) by photo-dehydrochlorination from poly (vinyl chloride)/polypyrrole composite film

Polypyrrole (PPy) was deposited electrochemically on a platinum plate from a nitric acid solution of pyrrole. The PVC/PPy composite film was finally obtained by casting poly(vinyl chloride) (PVC) onto the PPy electrode from a tetrahydrofuran solution of PVC. The prepared composite film was irradiated at 90°C with a low-pressure mercury lamp in the stream of hydrogen gas saturated with steam, and the PVC film was dehydrochlorinated, leading to the formation of conjugated polyene. The electrical conductivity (σ) of the PVC film in the irradiated composite film was reveled: σ=2.51 × 10^?5S cm^?1. By iodine doping, σ was further enhanced up to 5.04 X 10^?3 S cm^?1. The tensile strength of the irradiated composite film became larger than that of the original PVC film; i.e., the stress at break was: 461 (composite film); 401 kg cm^?2 (PVC). These results were brought about by the doping of radical species to the conjugated polyene. The anion, NO^?₃, doped during the electrodeposition of PPy was photodecomposed to generate radical NO₂ and this species was doped to the polyene, resulting in the formation of electrically conductive PVC and mechanically improved composite film. © 1994 John Wiley & Sons, Inc.     

Preparation and characterization of wet poly(vinyl chloride)-polypyrolle composite film

Wet poly(vinyl chloride) (wPVC) coated glassy carbon (GC) electrode was prepared by casting a DMF solution of poly(vinyl chloride) on glassy carbon and immersing it in methanol, and then in water. The wPVC coated GC (wPVC/GC) electrode showed electrochemical activity in aqueous solution; therefore, it was possible to obtain a wPVC/polypyrolle (PPy) composite by electropolymerization from aqueous solution of pyrolle (Py) into the wPVC matrix on the electrode. PPy segregated in wPVC matrix and the mechanical properties of PPy was improved by forming a composite without changing the electrochemical properties of PPy. The PPy/wPVC ratio can be controlled by controlling the concentration of PVC in DMF solution.     

Mechanical properties of blends of PAMAM dendrimers with poly(vinyl chloride) and poly(vinyl acetate)

Hybrid blends of poly(amidoamine) PAMAM dendrimers with two linear high polymers, poly(vinyl chloride), PVC, and poly(vinyl acetate), PVAc, are reported. The interaction between the blend components was studied using dynamic mechanical analysis, xenon nuclear magnetic resonance (NMR) spectroscopy, and tensile property measurements. The data suggest a much higher degree of interaction between components of PVAc-containing blends compared to those containing PVC. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2111–2117, 1998     

Relaxation properties of plasticised poly(vinyl chloride) and PVC blends

The temperature-frequency dependence of dielectric parameters for several PVC-plasticizer systems and PVC blends was obtained. Kinetic and activation parameters and α-relaxation spectra were estimated. The increase of the polar group number and size in the plasticizer molecules results in the narrowing of the relaxation spectra and in the increase of inner mobility of PVC segments. It was found for PVC-ABS and PVC-Paraloid blends that all relaxation characteristics depend on the miscibility of components. The results were also confirmed by the cloud point data.     

Suspension polymerization of vinyl chloride and the processibility of poly(vinyl chloride)

The most important technological procedure in the production of PVC is the suspension polymerization of vinyl chloride, as processibility of the polymer may be influenced to a considerable extent by the choice of polymerization conditions. Structure heterogeneities in PVC powders manifest themselves in plasticized PVC by the occurrence of “fish eye” particles. This review concerns the formation and properties of these particles and discusses the causes of their difficult processibility. Also, the relation between polymerization process and PVC dehydrochlorination is discussed and a new mechanism of its initiation based on the reactivity of cisoid enone structures is proposed. These structures catalyze elimination of hydrogen chloride from regular units of PVC by an interchain enzyme-like mechanism giving rise to chloroallyl structures.     

Thermal degradation of poly(vinyl chloride) synthesized with a titanocene catalyst

PVC was synthesized using a trichloroindenyltitanium-methylaluminoxane catalyst at room temperature, and its degradation was monitored along with a commercial sample at 160, 170 and 180 °C under air or nitrogen atmosphere. The process was followed by HCl evolution, yellowing index, colour formation and thermogravimetric analysis. The produced polymer had a lower molecular weight and higher surface area, compared with a commercial PVC, while ¹H NMR and T_g values show minimal differences between materials. The HCl evolution degradation studies indicate that produced PVC has a lower thermal resistance than commercial PVC, while TGA reveals the opposite behaviour. Yellowing index and colour evaluation give evidence that nitrogen atmosphere and high surface area in produced PVC allow the polyene growth, whereas low surface area and air atmosphere generate shorter polyenes and chromophoric species. Differences in degradation performance are thought to be due to chemical origin, inherent morphology and differences in instrumentation.     

Thermal stability, smoke emission and mechanical properties of poly(vinyl chloride)/hydrotalcite nanocomposites

Poly(vinyl chloride)/hydrotalcite (PVC/HT) nanocomposites were prepared through vinyl chloride suspension polymerization in the presence of HT nanoparticles surface modified with alkyl phosphate (AP). The thermal stability, smoke emission and mechanical properties of PVC/HT nanocomposites were investigated. It was found that AP molecules were effectively absorbed by HT particles with no intercalation into the interlayer of HT. The dispersion morphologies of PVC/HT nanocomposites were observed by transmission electron microscopy showing that the majority of HT particles were dispersed in the PVC matrix in the nanoscale. The Congo Red measurement and thermogravimetric analysis showed that the thermal stability time, and the temperatures at 10% weight loss and at the maximum weight loss rate of PVC resins increased as the weight fraction of HT in the composite resins increased. The well-dispersed nano-sized HT showed an obvious smoke suppression effect on PVC. The maximum smoke density decreased about 1/3 and 1/2 when 2.5 wt% and 5.3 wt% nano-sized HT were incorporated into PVC, respectively. Furthermore, PVC/HT nanocomposites exhibited greater tensile strength and impact strength than the pristine PVC.