热塑性淀粉/聚乙烯醇/蒙脱土三元纳米复合材料

用熔融挤出的方法制备了甘油塑化热塑性淀粉（TPS）/聚乙烯醇（PVA）/蒙脱土（MMT）纳米复合材料,添加蒙脱土和聚乙烯醇用以提高热塑性淀粉材料的力学性能。 在相对湿度50%的条件下,复合材料的XRD衍射谱图和透射电子显微镜测试表明,MMT以剥离状态均匀分布在TPS/PVA基体中;力学测试表明,当MMT的质量分数从0％增至5％时,复合材料的力学性能明显提高。 当蒙脱土的质量分数为3%时,复合材料最大抗张强度达到13.24 MPa,杨氏模量达到61.46 MPa。 这说明蒙脱土在复合材料中可以起到物理交联点的作用,提高了复合材料的力学性能。     

蒙脱土/二氧化钛复合颗粒电流变液材料的制备及其性能

利用溶胶-凝胶法制备了一种新型的蒙脱土/二氧化钛(MMT/TiO_2)复合电流变 颗粒材料，FT-IR，XRD，SEM分析表明TiO_2以纳米晶的形态包覆于蒙脱土表面。电 流变性能测试表明，MMT/TiO_2复合颗粒的电流变效应比纯蒙脱土电流变液有显著 提高，当颗粒体积分数为25%，直流电场强度为3kV/mm时，TiO_2质量分数为22.7% 的MMT/TiO_2复合颗粒电流变液的静态屈服应力达8.3kPa，此值约为纯蒙脱土电流 变液的4倍。同时发现TiO_2包覆量对电流变效应有重要影响。     

大分子不饱和单体法合成具有核壳结构的丙烯酸酯/聚氨酯乳液及表征

采用丙烯酸酯（AC）对水性聚氨酯（WPU）进行改性,合成了接枝型丙烯酸酯/聚氨酯(PUA)复合乳液。 随着共聚物中丙烯酸酯质量分数的增加,乳液外观由透明变为不透明,乳液粒径随之增大、分布变宽。 TEM显示,PUA乳胶粒子呈现清晰的核壳结构,且形态规整,粒径分布在60~120 nm之间。 FTIR测试表明,随着丙烯酸酯质量分数的增加,聚氨酯(PU)硬段氢键化作用先增强后减弱,硬段的有序度逐渐降低。 DSC分析表明,当AC的质量分数低于75%时,PU、聚丙烯酸酯(PA)两组分相容性较好,只出现一个玻璃化转变温度,并且随着PA质量分数的增加逐渐升高。 PA质量分数的增加,使胶膜的最大热失重速率从363 ℃提高至412 ℃,吸水率从11.3%降低至5.7%,弹性模量从16.4 MPa提高至47.6 MPa,拉伸强度从9.0 MPa提高至23.7 MPa,断裂伸长率从365%提高至408%,同时乳液的粘度下降,干燥时间变短,胶膜的附着力变好。     

三聚苯撑乙烯/蒙脱土发光光谱的时间依赖性

用原位插层法制备了插层型的三聚苯撑乙烯/蒙脱土(TPV/MMT)纳米复合材料. 研究了新制备及在室温储存180天后的TPV/MMT纳米复合材料的荧光光谱及蒙脱土层间距的变化情况. 荧光光谱分析表明, 储存180天后, TPV/MMT纳米复合材料的最大发射峰由494 nm蓝移到438 nm, 半峰宽由77 nm增加到104 nm. X射线衍射结果表明, 与新制备的复合材料相比, 蒙脱土的层间距由1.52 nm减小到1.22 nm. 红外光谱分析表明, 室温储存180天后的三聚苯撑乙烯苯环的某些特征峰由1598 和1554 cm-1分别红移到1506和1462 cm-1. 依据相关实验和理论数据探讨了储存180 天前后TPV在蒙脱土中聚集态结构的变化方式.     

有机硅蒙脱土复合改性水性聚氨酯的研究

采用插层聚合制备了改性的水性聚氨酯乳液。X射线研究表明,蒙脱土以层间距5．19nm分散在水性聚氨酯基体中。硅烷和蒙脱土改性水性聚氨酯具有性能互补的效果,当有机蒙脱土和有机硅烷的质量分数分别为O．01及O．02时,聚氨酯乳液涂膜的拉伸强度和断裂伸长率比未改性时分别提高了70％、18％,吸水率降低了49％。     

原位聚合制备聚乙烯/蒙脱土(MMT)纳米复合材料的研究

利用MgCl₂在醇中溶解和蒙脱土(MMT)在醇中层间膨胀的特性,制备了MgCl₂/TiC_l4负载于MMT层间的MMT/MgCl₂/TiC_l4催化剂,并通过原位聚合合成了聚乙烯/蒙脱土纳米复合材料.经广角X射线衍射(WAXD)和透射电子显微镜(TEM)分析表明,蒙脱土片层在乙烯聚合过程中发生了层间剥离,以单片层或几片层共存的形式无规地分散于聚乙烯基质中.与分子量相近的纯聚乙烯相比,极低的蒙脱土含量(质量分数<1%)能使复合材料的屈服强度、拉伸强度和拉伸模量有很大提高.复合材料中蒙脱土片层以纳米尺寸在聚乙烯基质中的良好分布和对聚乙烯分子链运动的限制作用是力学性能提高的主要因素.     

双单体原位接枝插层法制备聚丙烯纳米复合材料的研究Ⅰ.制备、表征及力学性能的研究

用有机插层剂处理蒙脱土原土 ,制得有机蒙脱土 (O MMT) .采用双单体 (马来酸酐和苯乙烯 )原位接枝插层法 ,制备了聚丙烯 蒙脱土纳米复合材料母料 .将母料与聚丙烯基体在双螺杆上共混挤出 ,制得聚丙烯 蒙脱土纳米复合材料 (PP Montmorillonetenanocomposites,PMNC) .这是制备聚合物纳米复合材料的一种新方法 .通过X 射线衍射测试 (XRD)表明 ,有机蒙脱土片层 0 0 1面间距从原土的 1 4 9nm扩大到 2 96nm ,复合材料中蒙脱土片层 0 0 1面间距由有机蒙脱土的 2 96nm扩大到 4 0nm .力学性能测试表明 ,复合材料的力学性能明显优于PP基体 ,在提高材料拉伸强度的同时 ,缺口冲击强度也得到很大的提高 .用扫描电镜 (SEM)对材料的冲击断面形貌进行了研究 ,并从理论上分析了断裂机理 .随着蒙脱土含量的增加 ,冲击断裂形式逐渐从脆性断裂变成韧性断裂     

4,4'-二氨基二苯醚二苯酮固化环氧树脂/粘土纳米复合材料的研究

采用离子交换法, 用十六烷基三甲基溴化铵处理钙基蒙脱土(MMT), 使蒙脱土的层间距由1.49 nm扩大到2.21 nm, 制备了环氧树脂/ BADK/MMT纳米复合材料, 并用XRD等手段研究了有机蒙脱土在环氧树脂中的插层及剥离行为. 研究结果表明, 蒙脱土含量及环氧树脂与有机土的混合温度和时间均对固化后复合材料的剥离产生影响, 只有在特定条件下才能得到剥离型纳米复合材料.     

聚苯胺/离子液体/蒙脱土纳米复合材料的制备及其导电性能研究

采用1-羧甲基-3-甲基咪唑氯化盐离子液体对钠化蒙脱土进行插层改性,然后用苯胺的盐酸溶液进行二次插层,以过硫酸铵为氧化剂,盐酸溶液为掺杂剂,使进入离子液体/蒙脱土(CMMIm/MMT)层间的苯胺(An)发生氧化聚合反应,制备了一种具有良好导电性的聚苯胺/离子液体/蒙脱土复合材料(PANI/CMMIm/MMT).用红外光谱、X-射线衍射,热重分析和DSC对样品进行了表征.结果表明当离子液体/蒙脱土用量为7.5%、盐酸浓度为1mol/L、过硫酸铵与苯胺的摩尔比为1∶1、0℃下反应6h时制备的PANI/CMMIm/MMT纳米复合材料电导率最高,达到了0.3S/cm,是相同条件下聚苯胺/钠化蒙脱土纳米复合材料电导率的2.5倍,聚苯胺的7.5倍.     

高分散 Ru/MMT 催化剂的制备及其催化喹啉加氢性能

 通过简单的离子交换法制备出高分散的蒙脱土 (MMT) 负载 Ru 催化剂, 采用 X 射线衍射、X 射线光电子能谱、程序升温还原和高分辨透射电子显微镜等手段对催化剂进行了表征. 结果表明, 金属 Ru 在蒙脱土层间高度分散, Ru 的平均粒径约 2 nm. 在喹啉加氢反应中, 该催化剂显示出很高的反应活性和选择性. 在 2 MPa 和 60 °C 的温和条件下, 以水为溶剂时, Ru/MMT 催化喹啉加氢生成 1,2,3,4-四氢喹啉的选择性高于 96.4%, 喹啉转化率达 99.2%. 当温度升高到 140 °C、压力增加到 3 MPa 时, 不需要补加催化剂就可以将喹啉一步加氢生成十氢喹啉, 选择性高达 98.1%.     

Preparation and characterization of novel thermal-stable vinylidene chloride–methyl acrylate–glycidyl methacrylate copolymer

A novel copolymer was synthesized by vinylidene chloride (VDC)/methyl acrylate (MA)/glycidyl methacrylate (GMA). The Fourier transform infrared (FTIR) and ¹H-nuclear magnetic resonance analyses indicated that the copolymer of VDC/MA/GMA (PVMG) was synthesized successfully. The influences of GMA on the molecular weight, melting point, and thermal stability of copolymer were investigated by gel permeation chromatograph, differential scanning calorimeter, thermogravimetric analysis–FTIR, respectively. The copolymerization eliminated the phenomenon of “double melting peaks” for poly(vinylidene chloride), and the melting point was reduced to 165°C. The GMA also enhanced the thermal stability of copolymer, which was proved by the increased decomposition temperature of copolymer. The existence of GMA caused the cross-linking of the copolymer, which contributed to the improvement of barrier performance of PVMG.     

Preparation of epoxy-acrylic latex based on bisphenol F epoxy resin

Bisphenol F based epoxy-acrylic latex with different amount of epoxy resin was successfully prepared by semi-continuous seeded emulsion polymerization. The resulting composite latexes had a narrow size distribution of about 105 nm in diameter. The DSC result showed that the epoxy resin and polyacrylate were grafting copolymerization. The FTIR spectra showed that the epoxy group had been introduced into the epoxy acrylic latex system, and the composite latex could be crosslinked with epoxy hardener at room temperature. The crosslinked composite latex film exhibited a high Tg compared to epoxy-acrylic latexes. The surface of the films with the epoxy resin was regular, and diffused into the polyacrylate phase in the epoxy-acrylic latexes films. Since the curing reactions occurred before latex particle coalescence stage, the surfaces of the cured epoxy-acrylate latex films had a number of interface particle. Compared with the acrylic latex, the thermal stability of the epoxy-acrylate latex was increased, and the stability of the cured film increased with increasing epoxy content.     

Synthesis of polyaniline/multiwall carbon nanotube composite via inverse emulsion polymerization

The composite of polyaniline (PANI) and multiwall carbon nanotube carboxylated through acid treatment (c‐MWCNT) was synthesized by chemical oxidative polymerization in an inverse emulsion system. The resultant composites were compared with products from aqueous emulsion polymerization to observe the improvements in electrical conductivity, structural properties, and thermal stability obtained by this synthetic method. Prior to the inverse emulsion polymerization, MWCNT was treated with a strong acid mixture to be functionalized with carboxylic acid groups. Carboxylic acid groups on surfaces induced selective dispersibility between polar and nonpolar solvents because of the increase of hydrophilicity. As the content of c‐MWCNT was increased, the electrical conductivity was increased by a charge transport function from the intrinsic electrical conductivity of MWCNT and the formation of a highly ordered dense structure of PANI molecules on the surface of c‐MWCNT. The images observed with electron spectroscopy showed the capping of c‐MWCNT with PANI. The growth of additional ordered structures of PANI/c‐MWCNT composite, which was observed through wide‐angle X‐ray diffraction patterns, supported the capping by PANI. It was observed that the doping of the composite had a significant relationship with the concentration of dodecylbenzenesulfonic acid (DBSA). The thermal stability of PANI composite was improved by the addition of c‐MWCNT; this was thought to be related with structure ordering by inverse emulsion polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2255–2266, 2008     

Stability of Emulsion Polymerization of New Fluorinated Acrylate Emulsion and Its Characterization

The new fluorinated acrylate emulsion was synthesized by using the intermediate perfluorous nonene and 2-hydroxyethyl methacrylate as the staring reactants via semi-continuous seeded emulsion polymerization. The structures, glass transition temperature, thermal property and water repellency of the fluorinated acrylate emulsion were characterized with FTIR, differential scanning calorimetry, thermal analysis, and contact angle meter. Influences of many factors such as the theoretical solid content, the temperature of the emulsion polymerization on the stability of the emulsion polymerization, the added amount of emulsifiers and the added amount of the initiator were studied. Results show that the stability of the emulsion polymerization is fairly good when the theoretical solid content is below 30% and the reaction temperature is 80°C and the added amount of emulsifiers and the initiator are 6.0–8.0% and 2.0% respectively. In comparison with the acylate emulsion, the thermal stability of the fluorinated acrylate emulsion is decreased but the water repellency of the fluorinated acrylate emulsion is greatly increased.     

Effect of thermal treatment on the characteristics of electrospun PVDF−silica composite nanofibrous membrane

Composite nanofibrous membranes were prepared by the electrospinning and the thermal treatment from poly(vinylidene fluoride) (PVDF)-tetramethyl orthosilicate (TMOS) blend solutions. The average diameter of nanofibers was reduced with increasing the concentration of TMOS in the solution due to the decrease of the solution viscosity. The EDX spectra confirmed the presence of TMOS on the external surface of the composite nanofibrous membrane. The porosity of membranes was effectively enhanced by the introduction of electrospinning technique. However, the mechanical properties, thermal stability and hydrophobicity were not markedly amplified. Thus the thermal treatment of the composite membranes was carried out, leading to the enormous enhancement of the mechanical properties and hydrophobicity. In addition, XRD results revealed that the crystal structure of PVDF in the composite membranes transformed from α-phase to β-phase due to the formation of silica particles by the thermal treatment.     

反相非水乳液法制备聚酰亚胺微球

在N,N-二甲基甲酰胺(DMF)/Pluronic-F127、十二烷基苯磺酸钠(SDBS)/液体石蜡(LP)反相非水乳液体系中,以均苯四甲酸二酐(PMDA)和4,4′-二氨基二苯醚(ODA)为单体合成聚酰胺酸(PAA),采用吡啶/乙酸酐脱水剂,对PAA化学酰亚胺化,并进一步热酰亚胺化,制得PI耐热微球.产物通过红外、热重、扫描电镜表征.结果表明,较高的固含量和良好的乳液分散性有利于PI微球的形成;反相非水乳液体系稳定的配比条件是,VDMF∶VLP为1∶4,MF127∶MSDBS为3:2,乳化剂用量为9 wt%;在此配比条件下,当固含量为20%,热酰亚胺化温度不高于330℃时,可制得分散良好、球形规整、高热稳定性的PI微球,其粒径约为10μm.     

Preparation of heterogeneous film from core-shell composite polymer particles produced by the stepwise heterocoagulation method with heat treatment

Core-shell composite polymer particle consisting of a hydrophilic core and hydrophobic shell was produced by the stepwise heterocoagulation of small cationic styrene-butyl acrylate-methacryloyoxyethyl trimethylammonium chloride terpolymer particles onto a large anionic methyl methacrylate-ethyl acrylate-methacrylic acid terpolymer particle (LP), which was proposed by the authors in 1990. In order to prepare a film from such a core-shell composite polymer emulsion, the shell content was controlled by changing the diameter of LP and by increasing the methacrylic acid content in LP.     

Degradation of vinylidene chloride/phenylacetylene (VDC/PA) copolymers. Effect of internal unsaturation on poly(vinylidene chloride) stability

The thermal degradation of vinylidene chloride/phenylacetylene copolymers containing small but varying amounts of phenylacetylene has been examined in both the solid phase and in bibenzyl solution. Incorporation of phenylacetylene into the poly(vinylidene chloride) structure greatly facilitates degradative dehydrochlorination. Indeed, the presence of phenylacetylene promotes the formation of polyene segments during the polymerization process so that all the copolymers, even at very low phenylacetylene loading, are tan in color. The decreased stability of polymers containing interal unsaturation arises from an increased rate of initiation for degradative dehydrochlorination. The propagation rate is largely unaffected by the level of unsaturation initially present in the polymer. The ratio of hydrogen chloride to stilbene formed for degradation of these copolymers in bibenzyl solution is approximately 35:1. This suggests that the chlorine atom of the initially-formed radical pair preferentially abstracts an adjacent hydrogen atom rather than interacting with solvent, i.e., the chain-carrying radical pair does not dissociate appreciably as the unzipping dehydrochlorination occurs. Thus random double bonds introduced in a variety of ways may be identified as principal defect sites responsible for the initiation of the degradative dehydrochlorination of poly(vinylidene chloride). Species which promote the degradation of poly(vinylidene chloride) probably do so by facilitating the introduction of random double bonds into the structure.     

Preparation and Properties of Cellulose/Waste Leather Buff Biocomposites

The aim of the present work was to utilize waste leather buff (WLB) as filler in cellulose and make biocomposites for packaging applications such as wrappers. Cellulose was dissolved in the environmentally friendly ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl). To this solution, WLB was added in amounts of 5 to 25 wt.% of cellulose. The cellulose and cellulose/WLB composite films were prepared by regenerating the corresponding cast solutions in a water coagulation bath followed by washing and drying. These films were tested for their tensile properties, thermal stability, and morphology. The tensile modulus and strength of the composite films were lower than those of the matrix. The lowering of the tensile modulus and strength with increasing WLB loading was attributed to the random orientation of the leather fibers of WLB in the composites. However, the % elongation at break of the composite films was found to be higher than that of the matrix and increased with increasing WLB content. The possible interaction between the matrix and WLB filler was probed using FT-IR analysis. The thermal stability of the composite films was higher than that of the matrix. The increase in thermal stability of the composite films was attributed to cross-linked collagen protein leather fibers in WLB. The fractographs of the composite films indicated good interfacial bonding between cellulose and leather fibers of WLB. These composite films may be considered for packaging and wrapping applications.     

Poly(vinyl chloride) composite emulsion resins modified by polyurethane

An ionomer-type of polyurethane (PU) emulsion was prepared from toluene diisocyanate (TDI), polypropylene glycol (PPG) and dimethylol propionic acid (DMPA) following a self-emulsification process. The modified poly(vinyl chloride) (PVC) emulsion resin was obtained by in situ emulsion copolymerization using the PU as seeds in an autoclave. The effects of PU molecular weight on the mechanical properties and thermal stability of the PU/PVC materials were investigated. The composite latex particles and composite materials were determined and characterized using a laser particle size analyzer, transmission electron microscopy or scanning electron microscopy. The study results showed that the PU/PVC hybrid emulsion particles possess a core/shell structure. When the general mechanical properties of the composite materials increase, the thermal stabilities decrease a little. The tough fractures on the surface of the PU/PVC composite sample following impact are quite obvious. __________ Translated from Journal of Hebei Normal University (Natural Science Edition), 2007, 31(2): 228–232 [译自: 河北师范大学学报(自然科学版)]